Infinity TSS-SAT500 User's Manual
Contents
1. that is mounted to the speaker with the finished side of the collar facing the rear of the speaker Step 8 Carefully push the ball straight into the socket mounted on the wall angle the speaker as desired and tighten the collar using the enclosed metal bar Metal Bar x Figure 3 Bracket on wall CONNECTIONS After placing the si First turn off all audio system power Use to make your connections 18 gauge spe eakers you are ready to connect your system igh quality speaker wire aker wire with polarity coding is included For longer distances 16 gauge or heavier wire is recommen coding is usually the owner s manual receiver to confirm connection procedures when making speaker connections as shown in Observe polarities Figure 4 Connect each terminal on the ed The side of the wire s that were included wi receiver to the res ective red termina with a ridge or other onsidered positive polarity i e Also consult h your amplifier or ack of the amplifier or on each speaker Connect the black terminals in the same way Important Do not reverse polarities i e to or to when making connections Doing so will cause poor imaging and diminished bass response Be certain that positive and negative wire strands are completely isolated to avoid short circuits that may damage your equipment Insert Bare End Release2. Connector Stripe Press Connector 4 Stripe Hold Output GiS Receiver or Amplifier rear view One Channel Shown 0 o o gt Figure 4 Wiring diagram shows polarity connections for one channel of a home theater system MAINTENANCE AND SERVICE The TSS SAT500 enclosure may be cleaned using soft cloth to remove fingerprints or to wipe off dust wm All wiring connections should be inspected and cleaned or remade periodically The frequency of maintenance depends on the metals involved in the connections atmospheric conditions and other factors but once per year is the minimum If a problem occurs make sure that all connections are properly made and clean If a problem exists in one loudspeaker reverse the connection wires to the left and right system If the problem remains in the same speaker then the fault is with the loud speaker If the problem appears in the opposite speaker the cause is in another component or cable In the event that your TSS SAT500 ever needs service contact your local Infinity dealer or distributor or visit www infinitysystems com for a service center near you TSS SAT500 5 SPECIFICATIONS TSS SAT500 Frequency Range Recommended Amplifier Power Range Sensitivity 2 83V 1 meter Nominal Impedance Cross
3. wm n TOTAL SPEAKER SOLUTIONS TSS SAT500 Owner s Guide 230V TSS SAT500 Owner s GUIDE Table of Contents Introduction Included Planning Your System Placement Wall Mounting Connections Maintenance and Service Specifications CZ TSS SAT500 INTRODUCTION Infinity Total Solutions Infinity Total Solutions continues Infinity s longstanding commitment to accurate sound reproduction Our high quality drivers precision dividing networks and rigid well braced enclosures combine to deliver uncompromised performance in any multichannel home theater system In addition the TSS SAT500 is magnetically shielded for safe place ment adjacent to a television INCLUDED D lo 1 Speaker 1 Wall bracket PLANNING YOUR SYSTEM Before deciding where to best place your speakers survey your room and study Figures 1 and 2 Subwoofer Left Right Front Front Channel Center Channel Channel T Couch a Left Right Center Rear Channel Channel O Channel Figure 1 This overhead view shows a typical home theater plan Left right rear channels are for a 7 channel system Center rear channel is for a 6 channel system Subwoofer Right Front Channel Center Channel gt Right Surround Left Channel Front Channel Kj e SA Left ES Surround ES O Channel
4. Figure 2 This figure shows an alternate layout which may be more suitable for some rooms Left right rear channels are for a 7 channel system Center rear channel is for a 6 channel system PLACEMENT NOTE The TSS SAT500 can be placed directly on a shelf or mounted on a wall using the included wall bracket As Left and Right Front Channels For left and right front channels place one satellite to the left and another to the right of the television as shown in Figure 1 Since the speakers are magnetically shielded you can place them very close to the TV without worrying about the magnetic field distorting the picture As Surround Channels For left and right surround channels place one speaker on the left and another on the right to the side of or slightly behind the listening area The surround speakers should be mounted at a height of between 5 ft 1 5m and 7 ft 2m In 6 or 7 channel configurations place the rear channel s behind the listening position as shown in Figures 1 and 2 NOTE An Infinity powered subwoofer will add impact and realism to both music and film soundtracks Contact your Infinity dealer for recommendations on subwoofer models for your applicatio 5 Mounting on Floor Stands An optional TSS STAND500 floor stand is available should you prefer to place your TSS SAT500 satellites on the floor see your dealer or visit www infinitysystems com for more information In addition there is a 1 4
5. 20 insert in each satellite that allows the satellite to be mounted to many third party floor stands Unscrew the rear foot to reveal the insert TSS SAT500 3 wm WaLL MounTING The TSS SAT500 satellite is designed to be mounted on the wall There is a wall bracket included The speaker bracket will require four 1 1 2 10 wood screws each screw should be fastened to a wall stud If a wall stud is unavailable install an anchor appropriate for a 1 1 2 10 screw NOTE The customer is responsible for the correct selection and use of mounting hardware available through hardware stores that will ensure the proper and safe wall mounting of the speakers Step 1 Detach shelf stand by removing screw in rear of speaker lg Step 2 Mark the positions on the wall where you would like to place the mounting screws Step 3 Place bracket against the wall and fasten four 1 1 2 10 wood screws through the bracket s screw holes into the wall If a wall stud is not available use an appropriate anchor Step 4 Unscrew round collar C from bracket A 747 1 500 Step 5 Screw the ball and shaft assembly to 1 4 20 insert on rear of speaker Back out 1 2 of a turn and tighten nut against the speaker F Step 6 Attach speaker wire as shown on page 5 Step Drop round collar C over ball and shaft assembly
6. ies Incorporated Dolby and Pro Logic are registered trademarks of Dolby Laboratories DTS is a registered trademark of DTS Inc Part No 406 000 05350 11 05 o A Harman International Company
7. over Frequency Midrange Driver s High Frequency Driver Dimensions H x W x D Weight 150Hz 25 000Hz 3dB 10 100 watts 86d8 8Q 7 000Hz 64mm 2 1 2 magnetically shielded 19mm 3 4 magnetically shielded 195mm x 89mm x 70mm 7 11 16 x 3 1 2 x 2 3 4 0 5kg 1 2 Ib Infinity continually strives to update and improve existing products as well as create new ones The specifications and construction details in this and related Infinity publications are therefore subject to change without notice 6 TSS SAT500 Declaration of Conformity CE We Harman Consumer Group International 2 route de Tours 72500 Ch teau du Loir France declare in own responsibility that the products described in this owners manual are in compliance with technical standards EN 61000 6 3 2001 EN 61000 6 1 2001 2 gt Laurent Rault Harman Consumer Group International Ch teau du Loir France 11 05 NOTES wm TSS SAT500 TECHNOLOGY PERFORMANCE DESIGN 2005 Harman International Industries Incorporated AlI rights reserved Infinity Systems 250 Crossways Park Drive Woodbury NY 11797 USA wwwinfinitysystems com Infinity and Harman International are trademarks of Harman International Industries Incorporated registered in the United States and or other countries Total Solutions is a trademark of Harman International Industr
Download Pdf Manuals
Related Search