Impex PWR 6 User's Manual
Contents
1. 34 Washers 42 and one M10 Aircraft Nut 44 Do not over tighten the nut and bolt The Supports need to swivel on the Bolt D Attach two Bushings to the pivot on the Main Frame 1 Loosen and pull the Lock Knob on the Sliding Block 48 The Sliding Block needs to be able to slide on the Chromed Incline Adjustment Bar 9 Align the two Seat Support Frames 6 to both ends of the pivot on Main Frame Secure them with one M10 x 8 14 Allen Bolt 39 two 2 34 Washers 42 and one M10 Aircraft Nut 44 E Use the Lock Knob on the Sliding Block 8 to adjust and secure the backrest incline position STEP 3 See Diagram 3 A Place the Backrest Board 14 onto the Backrest Supports 7 Secure it with four M8 x 2 Allen Bolts 40 and Y 5 8 Washers 43 B Place the Seat Pad 13 onto the Seat Support Frames 6 Secure it with four M8 x 2 Allen Bolts 40 and Y 5 8 Washers 43 DIAGRAM 3 STEP 4 See Diagram 4 A Attach the Leg Developer 5 to the open bracket on the Main Frame 1 Secure it with an Axle 17 two M10 x 34 Allen Bolts 36 and two Y 34 Washers 42 B Insert one Foam Tube 10 halfway through the hole on the Main Frame Insert two Foam Tubes halfway through the holes on the Leg Developer 5 Push six Foam Rolls 24 onto the Tubes from both ends Plug six Foam Roll End Caps 25 into the Tubes C Slide the Olympic Sleeve 20 onto the weight post on the2. Washers 42 and one M10 Aircraft Nut 44 After completing the cable installation check the tightness of the cables If the cable is too loose move up the pulley If the cable is too tight move down the pulley F Draw the Cable around the Pulley then down to the bracket on the Front Vertical Frame Attach another Pulley to the right of the Pulley previously installed in Step C Secure the two Pulleys together with the same nut and bolt previously installed G Draw the Cable around the Pulley then up and clip to the back of Sliding Pulley Bracket 57 H Connect the Shiver Bar 67 or the Single Handle 94 to the Cable by a Hook 90 for various exercises 15 DIAGRAM 10 X EXPLODED DIAGRAM 1 CWVYSOVIC 44 1dX3 PARTS LIST KEY NO DESCRIPTION Main Frame Front Stabilizer Rear Stabilizer Arm Curl Stand Leg Developer Seat Support Frame Backrest Support Sliding Block Incline Adjustment Bar Foam Tube Curl Bar Support Frame Curl Handle Tube Seat Pad Backrest Board Arm Curl Pad Curl Handle Grip Axle Y 2 3 8 Bushing Y 1 v2 Bushing Olympic Sleeve L shaped Lock Pin Spring Clip Lock Knob Foam Roll Foam Roll End Cap Y x Yo Bushing Bushing 3 1 8 x 1 5 8 End Cap Y 1 Cone shaped End Cap Y 1 End Cap 1 5 8 x 2 3 8 End Cap 1 5 8 x End Cap 2 Sliding Block Sleeve Stabilizer End Cap M10 x 2 Carriage Bolt M10 x 34 Allen Bolt M10 x 1 37
3. info impex fitness com IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 00 11 12 WARNING 35 Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine Only one person at a time should use the machine If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors Keep hands away from all moving parts Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine Use the machine only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer Do not place any sharp object around the machine Disabled person should not use the machine without a qualified person or physician in attendance Before using the machine to exercise always do stretching exercises to properly warm up Never operate th
4. Allen Bolt M10 x 6 Allen Bolt M10 x 8 14 Allen Bolt M8 x 2 Allen Bolt M8 x 5 8 Allen Bolt 34 Washer Y 5 8 Washer M10 Aircraft Nut M6 x 16 Philips Screw Chrome Panel Screw Floor Stabilizer Cross Brace Upright Beam Left Support o lt NNNNA OH OAH HAHNDDOWAOHH HAANHH HAH an Ha WAH Aa NND A di C1 N Na o o HNO 19 Right Support Rear Vertical Frame Rear Stabilizer Front Vertical Frame Upper Frame Sliding Weight Post Sliding Pulley Bracket Left Safety Catch Right Safety Catch Chrome Panel Lat Bar Double Floating Pulley Bracket Weight Post 5 x 1 5 8 Bracket 4 3 8 x 2 3 8 Bracket 2 34 x 1 34 Bracket Shiver Bar 100 Upper Cable 268 Lower Cable Pulley Small Pulley 234 x 2 End Cap 1 34 Square End Cap 2 Square End Cap 2 x 2394 Stabilizer End Cap Rubber Bumper Lat Bar Grip Pulley Bushing 5 8 Pulley Bushing M10 x 2 3 8 Carriage Bolt M10 x 2 37 Carriage Bolt M10 x 3 1 8 Carriage Bolt M10 x 3 Carriage Bolt M10 x 2 34 Allen Bolt M10 x 2 Allen Bolt M10 x 1 37 Allen Bolt M10 x 2 3 8 Allen Bolt M10 x 5 8 Allen Bolt 2 3 8 x 2 Sleeve Hook Chain Right Bar Holder Left Bar Holder Single Handle IMPEX INC LIMITED WARRANTY IMPEX Inc IMPEX warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of
5. Use a Lock Knob 23 to hold the Sliding Pulley Bracket in position B Insert the Upper Frame 55 into the top opening on the Front Vertical Frame 54 Attach the rear end of Upper Frame to the Rear Vertical Frame C Secure the Upper Frame with two M10 x 5 8 Allen Bolts 88 and Y Washers 42 Secure the Upper Frame with two M10 x 2 3 8 Allen Bolts 87 one 2 34 x 1 4 Bracket 66 and two 234 Washers 42 D Slide two Olympic Sleeves 20 onto the posts on the Sliding Weight Post Attach two Spring Clips 22 to the Olympic Sleeves E Connect the Chain 91 to the Lat Bar 61 with a Hook 90 DIAGRAM 8 1 STEP 9 See Diagram 9 amp Cable Loop Diagram A Attach the 100 Upper Cable 68 to the opening on the front Upper Frame 55 Make sure the ball stopper of the Cable is under the Frame B Attach a Pulley 70 to the opening Secure it with one M10 x 2 77 Allen Bolt 85 two 5 8 Pulley Bushings 79 and one M10 Aircraft Nut 44 C Draw the Cable along the Upper Frame towards the back of the machine to the opening on the Upper Frame Repeat Step B above to install a Pulley D Draw the Cable around the Pulley and downward Attach a Pulley to the Double Floating Pulley Bracket 62 Secure it with one M10 x 1 34 Allen Bolt 86 two 34 Washers 42 and one M10 Aircraft Nut 44 Let the Bracket hanging for now E Draw the Ca
6. Leg Developer Attach a Spring Clip 22 to the Sleeve DIAGRAM 4 V STEP 5 See Diagram 5 A Attach the Arm Curl Pad 15 to the Arm Curl Stand 4 Secure it with two M8 x 5 8 Allen Bolts 41 and two 5 8 Washers 43 Insert the Arm Curl Stand into the front opening on the Main Frame 1 Use the Lock Knob to hold the desired Arm Curl height B Attach the Curl Bar Support Frame 11 to the open bracket on the Leg Developer 5 Lock it with a L shaped Pin 21 C Remove the Pin Curl Bar Handle and Arm Curl when using the Leg Developer to exercise DIAGRAM 5 STEP 6 See Diagram 6 A Attach an Upright Beam 49 to a Floor Stabilizer 47 Secure it with two M10 x 2 3 4 Carriage Bolts 81 Y Washers 42 and M10 Aircraft Nuts 44 Do not tighten the nuts and bolts yet B Attach the upper end of Left Support 50 to the Upright Beam Secure it with one M10 x 5 8 Allen Bolt 88 and Y 34 Washer 42 C Attach the lower end of Left Support 50 to the Floor Stabilizer 47 Attach one end of the Rear Stabilizer 53 to the Floor Stabilizer Align the holes and secure them with two M10 x 3 Carriage Bolts 83 Y 34 Washers 42 and M10 Aircraft Nuts 44 D Repeat Steps A B and C above to install the other side E Securely tighten all Nuts and Bolts DIAGRAM 6 STEP 7 See Diagram 7 A Attach the Front Vertical Frame 54 to the Rear Stabilizer 53 Secu
7. NOTE Please read all instructions carefully before using this FITNESS PRODUCTS Table of Contents an POWERHOUSE CLUB Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model PWR 6 Retain This Manual for Reference 06 30 03 OWNER S E MANUAL IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD CITY OF INDUSTRY CA 91746 Tel 800 999 8899 Fax 626 961 9966 ww impex fitness com info impex fitness com TABLE OF CONTENTS BEFORE YOU BEGIN cosa naar anne 1 IMPORTANT SAFETY NOTIGES u ae Enns 2 BHARHDOWAHREPAC erh 3 ASSEMBLY INSTRUCTIONS a ua 5 EXEEODEDJIIAGBRAM Uo mere hex cepe 17 PARTS LIST aa 19 O 20 ORDERING PAR TS au crx ada ran 20 BEFORE YOU BEGIN Thank you for selecting the POWERHOUSE CLUB PWR6 by IMPEX FITNESS PRODUCTS For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts we guarantee you complete satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOLL FREE customer service number Our Customer Service Agents will provide immediate assistance to you Toll Free Customer Service Number 1 800 999 8899 Mon Fri 9 a m 5 p m PST ww impex fitness com
8. ble around the Pulley and up to the opening on the top of the Rear Vertical Frame 52 Attach a Pulley to the opening Secure it with one M10 x 2 3 8 Allen Bolt 87 two 2 Pulley Bushings 78 and one M10 Aircraft Nut 44 F Draw the Cable down to the Sliding Weight Post 56 Secure the end of the Cable with one M10 x 34 Allen Bolt 36 two 94 Washers 42 and one M10 Aircraft Nut 44 DIAGRAM 9 STEP 10 See Diagram10 amp Cable Loop Diagram A Attach the 268 Lower Cable 69 to the Sliding Pulley Bracket 57 Attach two Small Pulleys 71 to the Brackets Secure them with two M10 x 1 34 Allen Bolts 86 four Y 34 Washers 42 and two M10 Aircraft Nuts 44 B Draw the Cable upward to the opening on top of the Front Vertical Frame 54 Attach a Pulley 70 to the opening Secure it with one M10 x 2 4 Allen Bolt 85 two 5 8 Pulley Bushings 79 and one M10 Aircraft Nut 44 C Draw the Cable over the Pulley and down to the open bracket on the Front Vertical Frame 52 Install a Pulley with one M10 x 2 37 Allen Bolt 84 two 23 4 Washers 42 and M10 Aircraft Nut 44 Push the Pulley to the left side and do not tighten the nut and bolt yet D Pull the Cable around the Pulley then up to the Double Floating Pulley Bracket 62 previously installed in Step 9 E Attach a Pulley to a selected hole on the Bracket Secure it with one M10 x 1 37 Allen Bolt 86 two Y Y
9. e machine if the machine is not functioning properly A spotter is recommended during exercise OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT IMPEX INC ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY HARDWARE PACK 39 M10 x 8 1 4 Allen Bolt Qty 1 38 M10 x 6 3 4 Allen Bolt Qty 1 Cm 35 M10 x 2 1 2 Carriage Bolt Qty 2 40 M8 x 2 Allen Bolt Qty 8 nmm 37 M10 x 1 3 4 Allen Bolt Qty 2 4 41 M8 Allen Bolt B d Li 44 M10 Aircraft Nut Qty 28 Q 12 pre Y 22 Spring Clip Qty 5 D 1 8 3 4 36 7 8 9 36 10 x 3 4 Allen Bolt Qty 7 21 L shaped Lock Pin Qty 1 0 27 Bushing Qty 16 43 5 8 Washer Qty 10 17 Axle Qty 1 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 HARDWARE PACK 83 M10 x 3 3 4 Carriage Bolt Qty 4 82 M10 x 3 1 8 Carriage Bolt Qty 4 81 M10 x 2 3 4 Carriage Bolt Qty 4 80 M10 x 2 3 8 Carriage Bolt Qty 2 1 XN 84 M10 x 2 3 4 Allen Bolt Qty 1 78 1 2 Pulley Bushing Qty 2 85 MIO x 2 1 2 ALlen Bolt Qty 3 87 M10 x 2 3 8 Allen Bolt Qty 3 79 5 8 Pulley Bushing 86 M10 x 1 3 4 Al
10. len Bolt Qty 4 um 88 M10 x 5 8 Allen Bolt Qty 10 91 Chain Qty 1 90 Hook Qty 2 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ASSEMBLY INSTRUCTION Tools Required Assembling the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended this machine be assembled by two or more people to avoid possible injury STEP 1 See Diagram 1 A Attach the Main Frame 1 to the Front amp Rear Stabilizers 2 amp 3 Secure each end with two M10 x 34 Allen Bolts 36 and Y 34 Washers 42 Attach a Lock Knob 23 to the hole underneath the Main Frame B Slide the Sliding Block 8 onto the Incline Adjustment Bar 9 Align the hole then secure it with a Knob Lock 23 to hold the Sliding Block in position C Attach the Incline Adjustment Bar to the brackets on the Main Frame Secure each end with one M10 x 2 12 Carriage Bolt 35 2 34 Washer 42 and M10 Aircraft Nut 44 DIAGRAM 1 STEP 2 See Diagram 2 A Attach four Bushings 27 to a Seat Support Frame 6 B Attach a Backrest Support 7 to the rear of the Seat Support Frame 6 Align the holes and secure them with one M10 x 1 94 Allen Bolt 37 and Y 34 Washer 42 Repeat the same procedure to install the other side C Attach two Bushings to the pivot on the Sliding Block 8 Attach two Bushings to each Backrest Supports 7 Align the holes and secure them with one M10 x 6 37 Allen Bolt 38 two
11. ration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state Register on line at www impex fitness com IMPEX INC 14777 Don Julian City of Industry CA 91746 ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Service Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time info impex fitness com When ordering replacement parts always give the following information Model Description of Parts Part Number Date of Purchase PONS 20
12. re it with two M10 x 5 8 Allen Bolts 88 and 32 Washers 42 Do not tighten all the nuts and bolts yet B Attach the Cross Brace 48 to the Left amp Right Supports 50 amp 51 Secure each end of Cross Brace with two M10 x 3 1 8 Carriage Bolts 82 one 5 x 1 5 8 Bracket 64 two 2 34 Washers 42 and two M10 Aircraft Nuts 44 C Attach the Rear Vertical Frame 52 to the rear bracket on the Front Vertical Frame 54 and the Cross Brace 48 Secure it to the Front Vertical Frame with two M10 x 5 8 Allen Bolts 88 and Y 34 Washers 42 Secure it to the Cross Brace with two M10 x 2 3 8 Carriage Bolts 80 one 4 3 8 x 2 3 8 Bracket 65 two 14 Washers 42 and M10 Aircraft Nuts 44 Securely tighten all nuts and bolts previously installed D Insert two Weight Posts 63 to the holes on the Left amp Right Supports 50 amp 51 Secure each Weight Post with one M10 x 5 8 Allen Bolt 88 and 237 Washer 42 Slide an Olympic Sleeve 20 onto each Weight Post Attach a Spring Clip 22 to the Olympic Sleeve E Insert the Left amp Right Bar Holders 93 amp 92 into the selected holes on the Upright Beams Insert the Left amp Right Safety Catches 58 amp 59 into the selected holes on the Upright Beams STEP 8 See Diagram 8 A Slide the Sliding Weight Post 56 onto the Rear Vertical Frame 52 Slide the Sliding Pulley Bracket 57 onto the Front Vertical Frame 54
13. two years on the Frame from the date of purchase This warranty extends only to the original purchaser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights on products returned to IMPEX must be prepaid by the customer This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and du
Download Pdf Manuals
Related Search