Impex MWM-981 Owner's Manual
Contents
1. IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 1 Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine 2 Only one person at a time should use the machine 3 Ifthe user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY 4 Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors 5 Keep hands away from all moving parts 6 Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine 7 Use the machine only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer 8 Do not place any sharp object around the machine 9 Disabled person should not use the machine without a qualified person or physician in attendance 10 Before using the machine to exercise always do stretching exercises to properly warm up 11 Never operate the machine if the machine is not functioning properly 12 A spotter is2. 9 Secure each Handle with one M8 x 34 Allen Bolt 61 and one 5 8 Curved Washer 76 B Insert 15 9 Long Foam Tube 31 halfway through the hole on Seat Support 5 Insert 15 Short Foam Tube 22 halfway through the hole on Leg Developer 7 C Push four Foam Rolls 26 onto the Tubes from both ends of each Tube DIAGRAM 4 11 Nit NIT ul AN STEP 5 See Diagram 5 A Attach one Swivel Pulley Bracket 417 to the open bracket on the back of Vertical Frame 4 Secure it with one M10 x 2 1 Allen Bolt 66 two Washers 73 and one M10 Aircraft Nut 70 Do not over tighten the Nut and Bolt Make sure the Swivel Pulley Bracket can swivel freely B Repeat Procedure A to install the other Swivel Pulley Bracket on the other side DIAGRAM 5 A l q HN E E U Wo 13 STEP 6 See Diagram 6 Cable Loop Diagram A B C D E T o I Attach the 126 Upper Cable 32 to the front open bracket under the Upper Frame 1 Attach a Pulley 35 to the bracket Secure it with one M10 x 1 9 Allen Bolt 62 two Y Y Washers 73 and one M10 Aircraft Nut 70 Draw the Cable towards the back of the machine to the open bracket on Vertical Frame 4 Repeat B to install a Pulley Draw the Cable around the Pulley then pull back to the opening on the Front P
3. Insert a Selector Rod 21 through the center hole Slide the Selector Stem 51 onto the Guide Rods Use a Weight Selector Pin 44 to select the number of Weight Plates to exercise Attach the ring on Weight Selector Pin s cable onto the Selector Rod Note Each Weight Plate weights approximately 10 Ibs Please refer to the Weight Resistance Chart in page 25 Attach the Seat Support 5 to the Vertical Frame Secure it with two M10 x 2 3 8 Carriage Bolts 58 one 1 9 x 4 Bracket 18 two 9 Washers 73 and two M10 Aircraft Nuts 70 Attach the Vertical Seat Support 6 to Seat Support and Base Frame Secure each end of Vertical Seat Support with two M10 x 1 Allen Bolts 64 and two 34 Washers 73 DIAGRAM 1 a o Amy Wee Mii RR STEP 2 See Diagram 2 A Attach the holes on the Upper Frame 1 onto the Guide Rods 11 Place the Upper Frame onto the Vertical Frame 44 B Secure the Upper Frame to the Guide Rods with two M10 x 1 Allen Bolts 64 and 3 Washers 73 C Secure the Upper Frame to the Vertical Frame with two M10 x 2 3 8 Carriage Bolts 458 one 1 9 x 4 Bracket 18 two Y 3 4 Washers 73 and two M10 Aircraft Nuts 70 D Securely tighten all Nuts and Bolts previously installed in Step 1 and Step 2 E Attach the Leg Developer 7 to the open bracket on Seat Support 5 Secure it with one M12 x 3 1 8 Allen Bolt 67 two
4. 2 3 4 5 6 7 8 9 10 1 1 13 14 15 16 17 18 19 20 0 1 2 3 4 5 ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury STEP 1 See Diagram 1 A oo w m I Insert the two Guide Rods 11 through Rubber Bumpers and into the holes on the Rear Stabilizer Secure each Guide Rod with one M10 x 1 Allen Bolt 64 and 34 Washer 73 from the bottom The Guide Rods has holes on the rod to lock the weight stack when not in use The shorter end of the guide rod with the lock hole will need to be pointed downwards towards the Rear Stabilizer Do not tighten all Nuts and Bolts starting from this procedure until instructed to do so Attach two Rubber Bumpers 28 onto the holes onto the Guide Rods Attach the Base Frame 3 to the Rear Stabilizer Secure them with two M10 x 4 Carriage Bolts 59 one U shaped Bracket 20 two 9 Washers 73 and two M10 Aircraft Nuts 70 Attach the Vertical Frame 4 onto the Base Frame Secure them with two M10 x 2 3 8 Carriage Bolts 58 one 1 x 4 4 Bracket 18 two Y Y Washers 73 and two M10 Aircraft Nuts 70 Slide 11 Weight Plates 50 onto the Guide Rods Make sure the deep grooves on the Weight Plates all face the back of the machine and downward Align the holes on the Weight Plates
5. of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state Register on line at www impex fitness com IMPEX INC 2801 S Towne Ave Pomona CA 91766 ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Service Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time info impex fitness com When ordering replacement parts always give the following information Model Description of Parts Part Number Date of Purchase POs 23
6. recommended during exercise 13 Do not intend to insert weight selector pin while the weight stack or top plate is in elevated position 14 Be certain the weight Selector Pin is completely inserted 15 Never use dumbbells or other means to increase the weight resistance Use only weight plates provided by manufacturer 16 This machine is designed and intended for home and consumer use only not for commercial use CARE AND MAINTENANCE 1 Lubricate moving parts with WD 40 or light oil periodically 2 Inspect and tighten all parts before using the machine 3 The machine can be cleaned using a damp cloth and mild non abrasive detergent DO NOT use solvents 4 Maximum user s weight 300 Ibs WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT IMPEX INC ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS WARNING LABEL REPLACEMENT amp W i ali IG SERIOUS INJURY MAY OCCUR Do not attempt to exercise or hang from the lat bar while it is placed or stored on the storage hooks Ci 1 3 Th E E LT TH El i uctions be i obtained prior to use Replace this label if damaged illegible or removed Ke
7. 2 1 Washers 74 and one M10 Aircraft Nut 71 F Attach Seat Pad 23 to Seat Support Secure it with four M8 x 5 8 Allen Bolts 60 and four Y 5 8 Washers 72 G Attach Backrest Board 24 to Vertical Frame Secure it with two M8 x 2 1 8 Allen Bolts 63 and two 5 8 Washers 72 DIAGRAM 2 A ca ANI AO III IN lt STEP 3 See Diagram 3 A Attach the Front Press Base 8 to the Upper Frame 1 Secure it with one 8 12 Front Press Axle 19 two Y 1 x Y 5 8 Washers 75 and two M10 Aircraft Nuts 70 Do not over tighten the Nuts B Insert the axle on the Left Butterfly 9 through the open hole on Front Press Base from bottom Secure it with one Y 1 x 5 8 Washers 75 and one M10 Aircraft Nuts 70 Do not over tighten the Nut Push one large Foam Roll 27 onto the Left Butterfly C Repeat Procedure B to install the Right Butterfly 10 D Insert the two Butterfly Lock Pins 45 through the holes on Front Press Base into holes on Butterfly to lock the Butterflies for Front Press exercise E Pull out the Butterfly Lock Pins and insert into the other open holes on the Front Press Base for Butterfly exercise 10 DIAGRAM 3 TW A 11 STEP 4 See Diagram 4 A Insert the Front Press Handle 12 into the hole on Right Butterfly 10 and Left Butterfly
8. Bar Grip 50 Weight Plate SONDA ERON Q Q OO mk Selector Stem Ankle Strap Hook 15 link Chain 2 x 2 End Cap 1 x 3 8 Bushing 1 x 5 8 Pulley Bushing M10 x 2 3 8 Carriage Bolt M10 x 4 Carriage Bolt M8 x 5 8 Allen Bolt M8 x 34 Allen Bolt M10 x 1 34 Allen Bolt M8 x 2 1 8 Allen Bolt M10 x 1 Allen Bolt M10 x 2 Allen Bolt M10 x 2 4 Allen Bolt M12 x 3 1 8 Allen Bolt M10 x 7 4 Allen Bolt M6 x 5 8 Philips Screw M10 Aircraft Nut M12 Aircraft Nut 5 8 Washer 34 Washer 1 Washer 1 x 5 8 Washer 5 8 Curved Washer ST5 Screw Single Handle mk o A OR IN UA MWM981 WEIGHT RESISTANCE CHART Weight Plate Led Front Butterfly Lat Low Developer Press Pull Pulley 1 30 31 15 30 30 2 40 44 20 40 40 3 50 57 25 50 50 4 60 70 30 60 60 5 70 83 35 70 70 6 80 96 40 80 80 7 90 109 45 90 90 8 100 122 50 100 100 9 101 135 55 110 110 10 102 148 60 120 120 11 103 161 65 130 130 Note Each plate weights 10 Ibs Numbers are approximate Actual weights may vary Values for Butterfly are for each arm 22 IMPEX INC LIMITED WARRANTY IMPEX Inc IMPEX warrants this product to be free from defects
9. NOTE Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model MWM 981 Retain This Manual for Reference 100322 OWNER S MANUAL MA PRODUCTS MARCY MWM 981 HOME GYM IMPEX INC 2801 S Towne Ave Pomona CA 91766 Tel 800 999 8899 Fax 626 961 9966 www impex fitness com info impex fitness com TABLE OF CONTENTS BEFORE TOU BEGIN aaa aan 1 IMPORTANT SAFETY NOTIGES was insana a ate ti na 2 HARDWARE IDENTIMER sie ada dasana sanar dopado 4 ASSEMBLY INSTRUC MONS asus ae 6 PARTS LS Td 21 RESISTANCE CHART an aaa Ban ar a ad 22 WARRANTY A ue tale as ee e a n tea e nul 23 ORDER 23 BEFORE YOU BEGIN Thank you for selecting the MARCY MWM 981 HOME GYM by IMPEX INC For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts we guarantee you complete satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOLL FREE customer service number Our Customer Service Agents will provide immediate assistance to you Toll Free Customer Service Number 1 800 999 8899 Mon Fri 9 a m 5 p m PST www impex fitness com info impex fitness com
10. acket hang for now E Draw the Cable around the Pulley and pull upward to the left open Swivel Pulley Bracket 17 Repeat C to install a Pulley F Draw the Cable over the Pulley and hook the end to the Left Butterfly 9 DIAGRAM 7 STEP 8 See Diagram 8 amp Cable Loop Diagram Attach the 164 Lower Cable 33 to the open bracket on the Base Frame 3 Attach a Pulley 35 to the bracket Secure it with one M10 x 1 Allen Bolt 62 two 34 Washers 73 and one M10 Aircraft Nut 70 Draw the Cable underneath the Pulley then pull upward towards the Double Floating Pulley Brackets 13 installed in Step 6 Attach a Pulley to the selected hole on the Brackets Secure it with one M10 x 1 4 Allen Bolt 62 two Cable Retainers 29 and one M10 Aircraft Nut 70 Draw the Cable around the Pulley then downward to an open bracket on Base Frame Repeat B to install a Pulley Draw the Cable around the Pulley and pull the Cable upward to the Angled Double Floating Pulley Brackets 16 previously installed in Step 7 Repeat B to install a Pulley Draw the Cable around the Pulley and downward to the open bracket on Base Frame Repeat Procedure B to install another Pulley Draw the Cable underneath the Pulley through the opening on Vertical Frame 4 to the opening on Vertical Seat Support 6 Attach a Pulley to the opening Secure it with one M10 x 2 4 Allen Bolt 66 two Y 1 x Y 5 8 Pulley Bushings 57 a
11. ep children and pets away from this equipment The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame If the labels are missing or illegible please call customer service at 1 800 888 8899 for replacements Apply the labels in the location shown 3 HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size 68 M10 x 7 n Allen Bolt Qty 1 Do im 59 M10 x 4 Carriage Bolt Qty 2 Z MM 58 M10 x 2 3 Carriage Bolt Qty 6 67 M12 x 3 4 Allen Bolt Qty 1 hum C mm 60 M8 x Allen Bolt Qty 4 66 M10 x 2 f Allen Bolt Qty 3 mm pm 65 M10 x 2 Allen Bolt Qty 2 61 M8 x 4 Allen Bolt Qty 2 mm 62 M10 x 1 n Allen Bolt Qty 11 76 Curved Washer Qty 2 63 M8 x 2 4 Allen Bolt Qty 2 m 64 M10 x 1 Allen Bolt Qty 9 457 1 x Pulley Bushing Qty 2 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size u m 19 8 3 Front Press Axle Qty 1 ee 54 15 Link Chain Qty 1 44 Weight Selector Pin Qty 1 E A 53 Hook Qty 2 46 2 Lock Pin Qty 1 T TT 70 M10 Aircraft Nut 71 M12 Aircraft Nut Qty 30 Qty 1 72 Y Washer 73 3 Washer Qty 6 Qty 46 74 T Washer 75 1 x Y Washer Qty 2 Qty 4 mm 0 1
12. in workmanship and material under normal use and service conditions for a period of two years on the Frame from the date of purchase This warranty extends only to the original purchaser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights on products returned to IMPEX must be prepaid by the customer This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties
13. nd one M10 Aircraft Nut 70 Draw the Cable underneath the Pulley to the bracket on the Leg Developer 7 Secure the end of Cable to the bracket with one M10 x 1 Allen Bolt 64 two 34 Washers 73 and one M10 Aircraft Nut 70 If the whole Cable system is too loose adjust the tension of the cable system by moving up or down the lower pulley on the Double Floating Pulley Bracket Moving up the pulley up will increase the tension in the pulley system conversely lowering the pulley will decrease the tension 17 DIAGRAM 8 STEP 9 See Diagram 9 A Attach Lat Bar 14 to the Upper Cable 32 with two Hooks 53 and one 15 link Chain 54 when doing Lat Pull exercises B Attach Shiver Bar 15 to the Lower Cable 33 use the two Hooks 53 and the 15 link Chain 33 from Lat Bar when doing Arm Curl exercises C Replace Shiver Bar with the Ankle Strap 52 or Single Handle 78 to the Lower Cable for various exercises D Insert a 2 Lock Pin 46 through the hole on Guide Rod and lock with a Combination Lock 47 to prevent any un authorized usage of the machine E Unlock the Lock and attach it to Selector Rod before using the machine DIAGRAM 9 Sir HI MEM INN N A A A N EN A EE ER WE MM 1 Set up the Lock Combination A The combination is pre set to 0 0 0 by the factory Turn the dials to 0 0 0 and aligned to
14. ress Base 8 Attach a Pulley to the opening Secure it with one M10 x 7 4 Allen Bolt 68 two Y Washers 73 and one M10 Aircraft Nut 70 Draw the Cable around the Pulley then through the opening on the Vertical Frame 2 to the open bracket on the back of Vertical Frame Repeat Procedure B to install a Pulley Draw the Cable over the Pulley and pull the Cable downwards Attach a Pulley to the upper hole on the two Double Floating Pulley Brackets 13 Secure it with one M10 x 1 9 Allen Bolt 62 two Cable Retainers 29 and one M10 Aircraft Nut 70 Let the Bracket hanging for now Draw the Cable around the Pulley then pull upwards the open bracket under the Upper Frame Repeat Procedure B to install a Pulley Draw the Cable downwards between the two Guide Rods 11 to the Selector Rod 21 Securely thread the bolt on the end of the Cable into the Selector Rod 14 DIAGRAM 6 FS k 126 STEP 7 See Diagram 7 amp Cable Loop Diagram A Hook one end of the 98 Butterfly Cable 34 to Right Butterfly 10 B Draw the Cable towards the right open Swivel Pulley Bracket 17 C Attach a Pulley 35 to the bracket Secure it with one M10 x 1 Allen Bolt 62 two Washers 73 and one M10 Aircraft Nut 70 D Draw the Cable over the Pulley then pull downward Attach the Cable to an Angled Double Floating Pulley Bracket 16 Repeat Procedure C to install a Pulley Let the Br
15. the Combination Set Up Line Pull out the shackle and turn 180 Turn the dials aligned to the Combination Set Up Line to your desired combination Pull out the shackle and twist back to normal position and the combination are set G Repeat Procedure C to F to re set the combination Combination Set Up Line 20 PARTS LIST KEY NO DESCRIPTION Upper Frame Rear Stabilizer Base Frame Vertical Frame Seat Support Vertical Seat Support Leg Developer Front Press Base Left Butterfly 10 Right Butterfly 11 Guide Rod 12 Front Press Handle 13 Double Floating Pulley Bracket 14 Lat Bar 15 Shiver Bar 16 Angled Double Floating Pulley Bracket 17 Swivel Pulley Bracket 18 19 x 4 Y Bracket 19 8 1 2 Front Press Axle 20 U shaped Bracket 21 Selector Rod 22 15 Short Foam Tube 23 Seat Pad 24 Backrest Board 25 Y 1 v2 Small Rubber Bumper 26 Foam Roll 27 Butterfly Large Foam Roll 28 Rubber Bumper 29 Cable Retainer 30 Cable Retainer Bushing 31 15 Long Foam Tube 32 126 Upper Cable 33 164 Lower Cable 34 98 Butterfly Cable 35 Pulley 36 1 Bushing 37 1 5 8 x 3 1 8 End Cap 38 1 1 8 x 2 3 8 End Cap 39 1 x 2 End Cap 40 1 5 8 x 3 1 8 Base Frame End Cap 41 2 End Cap 42 1 End Cap 43 1 Corn shaped End Cap 44 Weight Selector Pin 45 Butterfly Lock Pin 46 2 Lock Pin 47 Combination Lock 48 4 9 Grip 49 6 Lat
Download Pdf Manuals
Related Search