Impex MSS-7500 User's Manual
Contents
1. impex fitness com info impex fitness com IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 1 2 3 10 12 13 14 15 16 Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine Only one person at a time should use the machine If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors Keep hands away from all moving parts Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine Use the machine only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer Do not place any sharp object around the machine Disabled person should not use the machine without a qualified person or physician in attendance Before using the machine to exercise always do stretching exercises to proper2. into the ends C Slide an Olympic Sleeve 24 onto the weight post on Leg Developer Attach a Spring Clip 20 onto the Sleeve DIAGRAM 4 WVaOVIG dAAdO IdXYA PARTS LIST KEY NO DESCRIPTION QUANTITY 1 Upright Beam 2 2 Cross Brace 1 3 Main Seat Support 1 4 Front Post 1 5 Seat Bracket 1 6 Backrest Support 2 7 Crutch 2 8 Backrest Adjustment Bar 1 9 Leg Developer 1 10 Foam Tube 2 11 Backrest Board 1 12 Seat Pad 1 13 5 Ye Curved Bracket 2 14 6 x 3 2 Bracket 1 15 5 2 x 3 Curved Bracket 1 16 M18 Lock Knob 2 17 Sleeve 2 18 Rubber Cover 6 19 Foam Roll 4 20 Spring Clip 1 21 Leg Developer Axle 1 22 Plastic Bushing 2 23 Rubber Bumper 1 24 Olympic Sleeve 1 25 2 End Cap 2 26 Foam Roll End Cap 4 27 1 Square End Cap 2 28 1 End Cap 2 29 M12 x 7 Hex Bolt 1 30 M10 x 3 Carriage Bolt 4 31 M10 x 2 Carriage Bolt 4 32 M10 x 2 3 8 Carriage Bolt 2 33 M10 x 3 Allen Bolt 2 34 M8 x 1 5 8 Allen Bolt 8 35 5 8 Washer 8 36 3 Washer 12 37 1 Washer 2 38 M10 Aircraft Nut 10 39 M12 Aircraft Nut 1 40 4 Allen Wrench Tool 1 41 5 Allen Wrench Tool 1 42 6 Allen Wrench Tool 2 11 IMPEX INC LIMITED WARRANTY IMPEX Inc IMPEX warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of two years on the Frame from the date of purchase This warranty extends only to the original purcha
3. HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size 36 7 Washer Qty 12 37 1 Washer 20 Spring Clip Qty 1 Qty 2 35 2 Washer 21 Leg Developer Axle Qty 1 Qty 8 39 M12 Aircraft Nut 38 M10 Aircraft Nut Oty 1 Qty 10 ASSEMBLY INSTRUCTION Tools Required For Assembling the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended for two or more people to assemble this machine to avoid possible injury STEP 1 See Diagram 1 A Do not tighten the Nuts and Bolts until instructed to do so B Connect the two Upright Beams 1 by a Cross Brace 2 in the mid span Secure each end of the Cross Brace to Upright Beam with two M10 x 3 34 Carriage Bolts 30 one 5 2 Curved Bracket 13 two 3 4 Washers 36 and two M10 Aircraft Nuts 38 C Insert two Crutches 7 into the openings on the two Upright Beams Thread a M18 Lock Knob 16 into the Upright Beam to lock each Crutch at desired height D Place the Backrest Adjustment Bar 8 onto the selected peg to obtain the backrest incline DIAGRAM 1 a STEP 2 See Diagram 2 A Attach the Main Seat Support 3 to the Front Post 4 Secure it with two M10 x 2 3 8 Carriage Bolts 32 one 6 x 3 1 Bracket 14 two 3 4 Washers 36 and two M10 Aircraft Nuts 38 B Attach the Main Seat Support to the Cross Br
4. Please read all instructions carefully before using this product x Sa QGgear WEIGHT BENCH Table of Contents MSS 7500 Safety Notice Hardware Pack Assembly Instruction Exploded Diagram Parts List Warranty Ordering Parts Model MSS 7500 Retain This Manual for Reference 06 11 09 IMPEX INC OWNER S 14777 Don Julian Rd City of Industry CA 91746 Tel 800 999 8899 Fax 626 961 9966 MANUAL www impex fitness com info impex fitness com TABLE OF CONTENTS BEFORE YOU BEGIN eiretier ERr E RRE 1 IMPORTANT SAFETY NOTICE keete een 2 HARDWARE E 4 ASSEMBLY INSTRUCTIONS w ivcscvecscecvcsscaurdusnconadiancenaviseesanceneveanedaeeauncnaneassodans 6 EXPLODED DIAGRAM oisesiinerecdimcedecdsnenierevennitver Aa E a LA E AAA TEA AA 10 PARTS HST EE 11 WARRANTY E 12 ORDERING GE 12 BEFORE YOU BEGIN Thank you for selecting the SA GEAR WEIGHT BENCH MSS 7500 by IMPEX INC For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts we guarantee your complete satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOLL FREE customer service number Our Customer Service Agents will provide immediate assistance to you Toll Free Customer Service Number 1 800 999 8899 Mon Fri 9 a m 5 p m PST
5. ace 2 Secure it with two M10 x 2 1 Carriage Bolts 31 one 5 1 2 x 3 Curved Bracket 15 two 34 Washer 36 and two M10 Aircraft Nut 38 C Securely tighten all Nuts and Bolts in Step 1 and Step 2 DIAGRAM 2 7 STEP 3 See Diagram 3 A Attach the Seat Bracket 5 to the pivot on the Main Seat Support 3 Attach the holes on the end of the two Backrest Supports 6 to the Seat Bracket Align the holes Secure the two Backrest Supports Seat Bracket together to the pivot with one M12 x 7 Hex Bolt 26 two 1 Washers 37 and one M12 Aircraft Nut 39 Do not over tighten the Nuts and Bolts Make sure the Backrest Supports are able to swivel B Attach the Backrest Board 11 to the Backrest Supports Secure it with four M8 x 1 5 8 Allen Bolts 34 and four 5 8 Washers 35 C Place the Seat Pad onto the Seat Bracket Secure it with four M8 x 1 5 8 Allen Bolts 34 and four 5 8 Washers 85 DIAGRAM 3 STEP A See Diagram 4 A Attach the Leg Developer 9 to the open bracket on Main Seat Support 3 Secure it with one Leg Developer Axle 21 two M10 x 3 Allen Bolt 33 and two 34 Washers 36 Do not over tighten the Bolts Make sure the Leg Developer is able to swivel B Insert two Foam Tubes 10 halfway through the holes on the Leg Developer Push four Foam Rolls 19 onto the Tubes from both ends Plug four Foam Roll End Caps 26
6. arranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state Register on line www impex fitness com IMPEX INC 14777 Don Julian City of Industry CA 91746 ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Service Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time info impex fitness com When ordering replacement parts always give the following information Model Description of Parts Part Number Date of Purchase PoON gt 12
7. ly warm up Never operate the machine if the machine is not functioning properly A spotter is recommended during exercise This machine is designed and intended for home and consumer use only not for commercial use Maximum user s weight 300 Ibs Maximum weight on uprights 600 Ibs Maximum weight on leg developer 100 Ibs CARE AND MAINTENANCE 1 Inspect and tighten all parts before using the machine 2 The machine can be cleaned using a damp cloth and mild non abrasive detergent DO NOT use solvents WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT IMPEX INC ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS WARNING LABEL PLACEMENT The Warning Labels shown here have been placed on the Cross Brace If the label is missing or illegible please call customer service at 1 800 999 8899 for replacement Apply the label in location shown HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size 29 M12 x 7 Hex Bolt Qty 1 31 M10 x 2 An Carriage Bolt Qty 4 33 M10 x 3 Allen Bolt Qty 2 Coa 34 M8 x 1 2 Allen Bolt Qty 8 4 3 6 7 8 9 10 11 le 13 14 19
8. ser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights on products returned to IMPEX must be prepaid by the customer This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied w
Download Pdf Manuals
Related Search