Impex IGS-6201 Owner's Manual
Contents
1. Resistance in Pounds Numbers are approximate Actual weight may vary V alue for Butterfly is for each arm 43 IMPEX INC LIMITED WARRANTY IMPEX Inc IMPEX warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of two years on the Frame from the date of purchase This warranty extends only to the original purchaser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights on products returned to IMPEX must be prepaid by the customer This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some2. 124 3 Lock Washer 125 3 Washer Qty 16 Qty 3 107 Y 2 Wash 106 Y 2 Washer aes 88 We Qty 24 120 M5 x 4 Philips Screw Qty 3 105 M12 x 7 An Allen Bolt Qty 1 D D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size u 132 M10 x 1 3 Allen Bolt Oty 2 mm 131 M10 x 1 Allen Bolt Qty 1 1 mm 128 M8 x 2 3 Allen Bolt Qty 4 127 Cover Cap Qty 4 23 4 5 6 7 8 9 10 11 42 13 14 45 HARDWARE PACK 134 Cross Wrench Screw Driver Qty 1 135 8 Allen Wrench Qty 1 136 6 allen Wrench Qty 1 137 5 Allen Wrench Qty 2 9 ASSEMBLY INSTRUCTION Tools Required Assembling the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended two or more people assembling this machine to avoid possible injury STEP 1 See Diagram 1 A Attach the Butterfly Pulley Bracket 13 to the Main Support Frame 1 from the bottom Secure it with two M10 x 34 Allen Bolts 94 and two Y 34 Washers 107 B Place the two Rubber Bumpers 55 onto the holes on the Rear Base Frame 4 Insert the two Guide Rods 20 through the Rubber Bumpers into the holes on the Rear Base Frame C Attach the Main Support Frame 1 to the Rear Base Frame Secure it with two M10 x 3 Allen Bolts 98 one Br
3. DIAGRAM 12 31 STEP 13 See Diagram 13 A Attach the Leg Press Adjustment Frame 36 to the Leg Press Plate 35 Secure it with one M10 x 3 Allen Bolt 98 two 34 Washers 107 and one M10 Aircraft Nut 110 Use a Leg Press Lock Pin 26 to secure the Leg Press Plate at desired position B Attach the Front Press Seat Pad 48 to the Seat Support 11 Secure it with four M8 x 1 34 Allen Bolts 91 and 5 8 Washers 106 Insert the Seat Support into the Main Support Frame 1 Use the Seat Support Lock Pin 121 to lock the Seat Support in desired height 7 iS Y dd O y L T DA A her m ao u may Y EA R N QA NY d NN Y Step 14 See Diagram 14 A Attach a Weight Stack Cover 24 to the rear of the machine Secure it to the Brackets and Upper Frame with four M8 x 34 Allen Bolts 90 O 5 8 Lock Washers 124 and Y 5 8 Large Washers 43 Repeat the same procedure to install the other side B Attach the Butterfly Right amp Left Covers 27 amp 28 to the Butterfly Base Align the holes Secure them to the Butterfly Base with two M10 x 2 v2 Allen Bolts 96 four 34 Washers 107 and two M10 Aircraft Nuts 110 C Insert the Foam Tube 5 halfway through the hole on the Leg Developer 6 Push two Foam Rolls 63 onto the Tube Plug two Foam Roll End Caps 67 into the Ends Y 5 Tos a
4. 34 Washer 1 Washer M8 Aircraft Nut M10 Aircraft Nut M12 Aircraft Nut M12 Nut ST3 5 Philips Screw Bushing M6 x 3 8 Schew Rotate Ring 2 x Ye Bushing Y 1 1 8 x 5 8 Bushing M4 Philips Screw O ee EE EE E o PARTS LIST KEY NO 120 121 122 123 124 125 126 127 128 129 130 131 132 DESCRIPTION M5 x Le Philips Screw Seat Support Lock Pin Y 2 Rubber Bumper Storage Bag 5 8 Lock Washer vz Washer Weight Stack Cover Bracket Cover Cap M8 x 2 34 Allen Bolt Leg Press Support Frame M8 x 1 Allen Bolt M10 x 1 Allen Bolt M10 x 1 5 8 Allen Bolt M6 x 5 16 Screw Cross Wrench Screw Driver Tool 8 Allen Wrench Tool 6 Allen Wrench Tool 5 Allen Wrench Tool QTY o A RNANARBSON N O 42 WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 8 9 Front Press 30 45 60 75 90 105 120 135 150 Butterfly 20 30 40 50 60 70 80 90 100 Lat Pull 30 40 50 60 70 80 90 100 110 Leg Developer 20 30 40 50 60 70 80 90 100 Leg Press 50 70 90 110 130 150 170 190 210 WEIGHT PLATE Station 10 11 12 13 14 Front Press 165 180 195 210 225 Butterfly 110 120 130 140 150 Lat Pull 120 130 140 150 160 Leg Developer 110 120 130 140 150 Leg Press 230 250 270 290 310
5. to Lower Cable 45 with one Long Chain 87 and two Hooks Replace Shiver Bar with Ankle Strap 56 for various Leg exercises ae 16 Lp zu il HK VAL I UTS Hi 4 Ga Y q KT NA AT ed a TY UES 38 8 CH ee lt x S K Ka Sy OQ ESOO dr sit WVdaDVId CHOO IdXW PARTS LIST KEY NO DESCRIPTION 1 Main Support Frame 2 Bracket 3 Butterfly Base 4 Rear Base Frame 5 Foam Tube 6 Leg Developer 7 Vertical Frame 8 Left Butterfly 9 Right Butterfly 10 Butterfly Handle 11 Seat Support 12 Backrest Support Frame 13 Butterfly Pulley Bracket 14 Backrest Adjustment Bracket 15 Foot Plate 16 Double Floating Pulley Bracket 17 Upper Frame 18 Front Press Base 19 Front Press 20 Guide Rod 21 1 7 8 Spacer 22 Y x Y Bushing 23 Y x 1 Bushing 24 Weight Stack Cover 25 Selector Rod 26 Leg Press Lock Pin 27 Butterfly Base Right Cover 28 Butterfly Base Left Cover 29 D shaped Washer 30 Y x 5 8 Bushing 31 Leg Press Rear Base Frame 32 Leg Press Backrest Support 33 Leg Press Seat Support 34 Leg Press Post 35 Leg Press Plate 36 Leg Press Adjustment Frame 37 Leg Press Seat Bracket 38 Leg Press Base Frame 39 Round Pulley Bracket 40 Lat Bar 41 Shiver Bar 42 Y 1 1 8 Washer 43 2 5 8 Large Washer 44 142 Upper Cable 45 184 Lower Cabl
6. A pe i a ug 34 ALU Step 15 See Diagram 15 A Attach the Leg Press Seat Pad 50 to the Leg Press Seat Bracket 37 Secure it with two M8 x 34 Allen Bolt 90 and two 5 8 Washers 106 Attach the Leg Press Seat Bracket to the Leg Press Seat Support 33 Secure it with M10 x 2 34 Allen Bolts 97 four 34 Washers 107 and two M10 Aircraft Nuts 110 Attach the Leg Press Backrest Board 51 to the Leg Press Backrest Support 32 Secure it with two M8 x 2 12 Allen Bolts 92 and two O 5 8 Washers 106 Attach the Storage Bag 123 to the Leg Press Backrest Support Secure it with three M5 x Philips Screws 120 and three 12 Washers 125 Attach the two Backrest Adjustment Brackets 14 onto the pivot on the Backrest Support 12 from each end Secure Front Press Backrest Board 49 to the Backrest Adjustment Brackets with four M8nx 34 Allen Bolts 90 and four 5 8 Washers 106 DIAGRAM 15 DI O 36 37 Step 16 See Diagram 16 A Connect the Lat Bar 40 to the Upper Cable 44 with one Short Chain 88 and two Hooks 89 B Insert one Butterfly Handle 10 into the pivot on the Right Butterfly 9 Secure it with one M8 x 34 Allen Bolt 90 5 8 Lock Washer 124 O1 1 8 Washer 42 and D shaped Washer 29 Repeat the same procedure to install the other Butterfly Handle C Connect the Shiver Bar 41
7. Weight Resistance Chart in page 43 11 DIAGRAM 2 u rx TA f NN se MM a O IR STEP 3 See Diagram 3 A Attach the Vertical Frame 7 onto the Main Support Frame 1 Secure it with two M10 x 2 3 Allen Bolts 97 four Y Washers 107 and two M10 Aircraft Nuts 110 Do not tighten the Nuts and Bolts yet B Attach the Upper Frame 17 onto the two Guide Rods 20 and the Vertical Frame C Secure the Upper Frame to the two Guide Rods with two M8 x 9 Allen Bolts 90 and two 5 8 Washers 106 Do not tighten the Bolts yet D Secure the Upper Frame to the Vertical Frame with two M10 x 3 Allen Bolts 98 one Bracket 2 four Y 34 Washers 107 and two M10 Aircraft Nuts 110 E Securely tighten all Nuts and Bolts 13 DIAGRAM 3 STEP 4 See Diagram 4 A Attach the Front Press Base 18 to the Upper Frame 17 Align the holes and insert the 5 7 8 Front Press Axle 81 through the holes Secure the Axle with one M8 x 34 Allen Bolt 90 Y 5 8 Lock Washer 124 and Y 5 8 Large Washer 43 on each end of the Axle B Attach the Backrest Support Frame 12 to the Vertical Frame 7 Secure it with one M10 x 3 34 Allen Bolt 101 two Y 34 Washers 107 and one M10 Aircraft Nut 110 Use the Backrest Support Lock Pin 75 on the Vertical Frame to secure the Backrest Support in Position DIAGRAM 4 eme 17 d e o
8. a m 5 p m PST ww impex fitness com info impex fitness com IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 1 2 3 10 11 12 13 WARNING Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine Only one person at a time should use the machine If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors Keep hands away from all moving parts Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine Use the machine only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer Do not place any sharp object around the machine Disabled person should not use the machine without a qualified person or physician in attendance Before using the machine to exercise always do stretching exerc
9. 95 two 34 Washers 107 and one M10 Aircraft Nut 110 Draw the Cable around the Pulley then upward to the open bracket under the middle of Upper Frame Let the Double Floating Pulley Bracket hanging for now H Attach a Pulley to the open bracket Secure it with one M10 x 1 34 Allen Bolt 95 two Y 34 Washers 107 and one M10 Aircraft Nut 110 Draw the Cable to the open bracket under the rear of Upper Frame Repeat Procedure H above to install a Pulley J Draw the Cable around the Pulley then downward between the two Guide Rods 20 to the Selector Rod 25 Attach a M12 Nut 112 to the head of Cable Thread the head of the Cable firmly into the Selector Rod 20 4 9 PAR E LSA y i SOS A SY gic SY SS NOS er ME Yny 7 5 24 2 FA e Ki SME Es Co A S ale Ia EH 7 N Q 4 UPPER CABLE LOOP DIAGRAM co DIAGRAM 9 1 DIAGRAM 9 2 23 STEP 10 See Lower Cable Loop amp Diagram 10 A B 63 D E T o I Attach the 184 Lower Cable 45 to the open bracket on the Leg Developer 6 Attach a Pulley 59 to the bracket Secure it with one M10 x 1 Allen Bolt 95 two Y 34 Washers 107 and one M10 Aircraft Nut 110 Draw the Cable to the opening on the Main Support Frame 1 Attach a Pulley to the opening Secure it with one M10 x 2 34 Allen B
10. NOTE Please read all instructions carefully before using this ETS product Fo T NES PRODUCT S Table of Contents IRON GRIP STRENGTH Safety Notice DUAL STATION HOME GYM Hardware Pack IGS 620 Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model IGS 6201 Retain This Manual for Reference 01 04 08 OWNER S MANUAL 14777 DON JULIAN RD CITY OF INDUSTRY CA 91746 Tel 800 999 8899 Fax 626 961 9966 www impex fitness com info impex fitness com TABLE OF CONTENTS BEFORE YOU BEGIN a an 1 IMPORTANT SAFETY NOMIC 2 4 ASSEMBLY INSTRUCTIONS nee 10 EXPLODED DIAGRAM a an Bin 40 PARTS 110 41 ua 43 WARRANT N kt a 44 ORDERING PARTS dee ee Eh da 44 BEFORE YOU BEGIN Thank you for selecting the IRON GRIP STRENGTH IGS 6201 HOME GYM by IMPEX FITNESS PRODUCTS For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts we guarantee you complete satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOLL FREE customer service number Our Customer Service Agents will provide immediate assistance to you Toll Free Customer Service Number 1 800 999 8899 Mon Fri 9
11. acket 2 four 34 Washers 107 and two M10 Aircraft Nuts 110 Rotate the Guide Rods to align the holes so the bolts can go through D Install four Weight Stack Cover Brackets 126 to the Rear Base Frame Secure the Brackets with four M8 x 2 34 Allen Bolts 128 eight Y 5 8 Washers 106 and eight M8 Aircraft Nuts 109 E Attach the Foot Plate 15 to the front base on the Main Support Frame Align the holes and secure it with one M8 x 3 Allen Bolt 93 two Y 5 8 Washers 106 and one M8 Aircraft Nut 109 DIAGRAM 1 STEP 2 See Diagram 2 A Attach the Butterfly Base Frame 8 to the Main Support Frame 1 from the bottom Secure it with two M10 x 3 Allen Bolts 98 one Bracket 2 four 9 Washers 107 and two M10 Aircraft Nuts 110 Slide fourteen Weight Plates 73 onto the two Guide Rods 20 Make sure all the holes on the Weight Plates are facing the back of the machine and the grooves are all on the bottom Each Plate weights approximately 10 lbs Insert the Selector Rod 25 into the center of the stack Slide the Selector Stem 72 onto the Guide Rods Secure the Selector Stem to the Selector Rod with one M12 x 2 3 8 Allen Bolt 83 and one M12 Aircraft Nut 111 Attach the ring on the Weight Selector Pin 82 onto the Selector Rod Insert the Weight Selector Pin into the selected hole to select the numbers of Weight Plates for exercise Please refer to the
12. d I A N STEP 5 See Diagram 5 A Insert the axle on the Left Butterfly 8 into the left pivot on the Butterfly Base 3 from the bottom Secure it with one M8 x 34 Allen Bolt 90 5 8 Lock Washer 124 Y 1 1 8 Washer 42 and D shaped Washer 29 Repeat the procedure to install the Right Butterfly 9 B Attach the Leg Press Rear Base Frame 31 to the Main Support Frame 1 Secure it with two M10 x 3 1 Allen Bolt 100 four Y Washers 107 and two M10 Aircraft Nuts 110 Do not tighten the Nuts and Bolts yet DIAGRAM 5 iS TTT US adil 16 STEP 6 See Diagram 6 A Attach the Front Press 19 to the Front Press Base 18 Align the holes Secure it with one M12 x 7 1 8 Allen Bolt 105 two 1 Washers 108 and one M12 Aircraft Nut 111 Cover the Bolt and Nut with two Cover Caps 127 Use the Front Press Lock Pin 76 on the Front Press to lock the Front Press in desired position B Attach the Leg Developer 6 to the open bracket on the Main Support Frame 1 Secure it with one M12 x 3 3 8 Allen Bolt 104 two Y 1 Washers 108 and one M12 Aircraft Nut 111 Cover the Bolt and Nut with two Cover Caps 127 DIAGRAM 6 lt d e Sa dE NCCE Caution Flease be aware of the sharp d b edge at the end of 2 y r the bench press arms p Mi i NN 17 STEP 7 See Diagram 7 A Attach the Leg Pr
13. e 46 90 Butterfly Cable 47 123 Leg Press Cable 48 Front Press Seat Pad 49 Front Press Backrest Board 50 Leg Press Seat Pad 51 Leg Press Backrest Board 52 Rear Base Frame Rubber Bumper 53 Leg Press Post Bushing 54 Y 1 Cone shaped End Cap 55 Rubber Bumper 56 Ankle Strap 57 234 x 2 End Cap 58 2 Square End Cap 59 Pulley 60 1 34 Square End Cap o ANON N xpA a dl o 2 2 2 A AN BAA ANS Phi A a A DD a paa a yo ch ch vk ch Y Lat Bar Holder Cover 1 End Cap Foam Roll T shaped Handle 21 14 End Cap 2 x 1 End Cap Foam Roll End Cap 2 3 8 x 1 1 8 End Cap Front Press Cover Front Press Handle Grip Butterfly Handle Grip Selector Stem Weight Plate Bar Handle Frame Sleeve Backrest Support Lock Pin Front Press Lock Pin Leg Press Lock Pin Sleeve 1 12 x 1 Bushing 2 x 1 Bushing Y 2 x 1 3 8 Bushing 5 7 8 Front Press Axle Weight Selector Pin M12 x 2 3 8 Allen Bolt 3 vi Leg Press Axle Bar Handle Frame 1 1 8 Spring Long Chain Short Chain Hook M8 x 34 Allen Bolt M8 x 1 34 Allen Bolt M8 x 2 12 Allen Bolt M8 x 3 Allen Bolt M10 x 34 Allen Bolt M10 x 1 34 Allen Bolt M10 x 2 12 Allen Bolt M10 x 2 34 Allen Bolt M10 x 3 Allen Bolt 1 7 8 Spring M10 x 3 12 Allen Bolt M10 x 3 34 Allen Bolt M10 x 4 3 8 Allen Bolt M10 x 5 1 8 Allen Bolt M12 x 3 3 8 Allen Bolt M12 x 7 1 9 Allen Bolt 5 8 Washer
14. ess Base Frame 88 to the bracket on the Leg Press Rear Base Frame 31 Secure it with two M10 x 2 34 Allen Bolts 97 and two Y 34 Washers 107 Securely tighten the Nuts and Bolts previously installed in Step 6 Procedure C B Attach the Leg Press Post 34 to the open bracket on the Leg Press Base Frame Insert the 3 4 Leg Press Axle 84 through the pivot Secure each end of the Axle with one M8 x 34 Allen Bolt 90 5 8 Lock Washer 124 and Y 5 8 Large Washer 43 C Attach the Leg Press Backrest Support 32 to the Leg Press Base Frame Secure it with two M10 x 3 v2 Allen Bolts 100 four 34 Washers 107 and two M10 Aircraft Nuts 110 Ys lt A OKS SA UU E d KS Wi NN yu SS Y A 18 STEP 8 See Diagram 8 A Attach the Leg Press Seat Support 33 to the Leg Press Base Frame 38 Secure it with four M10 x 34 Allen Bolts 94 and Y 34 Washers 107 Do not tighten the Bolts yet B Attach the Leg Press Seat Support to the Leg Press Backrest Support 32 Secure it with two M10 x 2 9 Allen Bolts 97 four Y 34 Washers 107 and two M10 Aircraft Nuts 110 C Securely tighten the Nuts and Bolts installed in Procedure A DIAGRAM 8 y LR i may i NP d 7 W Ka K i g 19 STEP 9 See Upper Cable Loop 8 Diagram 9 A Attach the 142 Upper Cable 44 to the open
15. ises to properly warm up Never operate the machine if the machine is not functioning properly A spotter is recommended during exercise Maximum user weight is 300 lbs CARE AND MAINTENANCE 1 Inspect and tighten all parts before using the machine 2 The machine can be cleaned using a damp cloth and mild non abrasive detergent DO NOT use solvents BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED READ ALL IMPEX INC ASSUMES WARNING LABEL PLACEMENT DO MOT MISUSE THIS EQUIPMENT lr plu rm rc ot nen teehee F dii Wd Eri aur ka red Feb YF Proper PIE bo mirinirwrd primr ra un Betiere tien baer 8 arm aad peru arm iy iron cha The warning labels have been placed on the unit in location shown If the labels are missing or illegible please call customer service at 1 800 888 8899 for replacements Apply the labels in location shown HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size 82 Weight Selector Pin Qty 1 Po 81 5 Zn Front Press Axle Qty 1 2 55 Rubber Bumper Qty 2 o 43 8 Large Washer Qty 12 Co 42 14 Wa
16. n Bolt 131 two Y 34 Washers 107 and one M10 Aircraft Nut 110 27 g LEG PRESS CALBE LOOP o fj W E IM d AS La SM A y N 28 DIAGRAM 11 STEP 12 See Butterfly Cable Loop and Diagram 12 A B o m Attach one end of 90 Butterfly Cable 46 onto the open slot on the Left Butterfly 8 Draw the Cable to the left horizontal bracket on the Butterfly Pulley Bracket 13 Attach a Pulley 59 to the bracket Secure it with one M10 x 1 34 Allen Bolt 95 two 34 Washers 107 and one M10 Aircraft Nut 110 Draw the Cable to the left vertical open bracket Secure a Pulley to the bracket with one M10 x 1 5 8 Allen Bolt 132 two Washers 107 and one M10 Aircraft Nut 110 Draw the Cable under the Pulley and then upward to the Double Floating Pulley Bracket 16 previously installed in Step 10 Attach a Pulley to the Bracket Secure it with one M10 x 1 34 Allen Bolt 95 two Y 34 Washers 107 and one M10 Aircraft Nut 110 Draw the Cable around the Pulley then downward Repeat Procedure B to install a Pulley to the right vertical amp horizontal bracket Draw the Cable to the Right Butterfly 9 Attach the end of Cable to the open slot on the Right Butterfly Se gt LA s n UT US Rail p ei Zee d Ca SAS QN NY NY NS gt lA zz 7 CE n B
17. nd of 123 Leg Press Cable 47 to the Pulley pre installed on the Leg Press Rear Frame 31 Draw the Cable over the Pulley along the Leg Press Base Frame to the other end Attach the Cable to the open bracket on the Leg Press Rear Base Frame Attach a Pulley to the bracket Secure it with one M10 x 1 34 Allen Bolt 95 two Y 34 Washers 107 and one M10 Aircraft Nut 110 Draw the Cable around the Pulley then upward to the Short Chain 88 installed in Step 10 Attach the Cable to the Hook 89 After completion of all Cables installation come back to this step to adjust the tension of the Cable system Move up the Hook one joint on Short Chain to increase the tension Move down the Hook to loose the tension Draw the other end of the Cable along the Leg Press Base Frame 38 to the open bracket on the Leg Press Base Frame Attach a Pulley to the bracket Secure it with one M10 x 1 9 Allen Bolt 95 two Y 34 Washers 107 and one M10 Aircraft Nut 110 Draw the Cable under the Pulley upward to the other open bracket Secure a Pulley to the bracket with one M10 x 3 Allen Bolt 98 and one M10 Aircraft Nut 110 Draw the Cable over the Pulley then downward to another open bracket on the Leg Press Base Frame Attach a Pulley to the bracket Repeat Procedure E above to install a Pulley Draw the Cable around the Pulley then upward to the open bracket Secure the head of Cable to the bracket with one M10 x 1 Alle
18. olt 97 and one M10 Aircraft Nut 110 Draw the Cable through the opening on the Butterfly Pulley Bracket 13 to the open bracket under the Main Support Frame Attach a Pulley to the open bracket Secure it with one M10 x 1 34 Allen Bolt 95 two Y 34 Washers 107 and one M10 Aircraft Nut 110 Draw the Cable to the open bracket on the Double Floating Pulley Bracket 16 previously installed in Step 9 Repeat Procedure D above to install a Pulley Draw the Cable around the Pulley then downward Attach the Cable to another Double Floating Pulley Bracket Repeat Procedure D above to install a Pulley Draw the Cable around the Pulley then upward Let the Double Floating Pulley Bracket hanging for now Draw the Cable to the Upper Frame 17 Attach a Pulley to the hole on the right side of the Upper Frame Secure the Pulley to the Upper Frame with M10 x 4 3 8 Allen Bolt 102 one Round Pulley Bracket 39 two 0 34 Washers 107 and one M10 Aircraft Nut 110 Draw the Cable around the Pulley then downward Connect a Short Chain 88 to the Cable with a Hook 89 Attach a Hook to the other end of the Short Chain Let the Short Chain hanging for now 24 LOWER CABLE LOOP l d A u 8 ky IE N A AZ Sk AN Y A f N Ta GA Y OK al DIAGRAM 10 STEP 11 See Leg Press Cable Loop and Diagram 11 A w Connect one e
19. pulley bracket under the Upper Frame 17 Attach a Pulley 59 to the open bracket Secure it with one M10 x 1 9 Allen Bolt 95 two Y Washers 107 and one M10 Aircraft Nut 110 Make sure the ball stopper on the Cable is underneath the Upper Frame B Draw the Cable over the Pulley to the second open bracket under the Upper Frame Attach a Pulley to the open bracket Secure it with one M10 x 34 Allen Bolt 95 two Y 34 Washers 107 and one M10 Aircraft Nut 110 C Draw the Cable around the Pulley then to the upper opening on the Front Press Base 18 Attach a Pulley to the opening Secure it with one M10 x 5 1 8 Allen Bolt 103 two 34 Washers 107 two 1 7 8 Spacers 21 and one M10 Aircraft Nut 110 Note the direction of the Bolt shown in Diagram 9 1 C D Draw the Cable around the Pulley to the upper opening on the Vertical Frame 7 Attach a Pulley to the opening Secure it with one M10 x 3 42 Allen Bolt 100 and one M10 Aircraft Nut 110 E Draw the Cable around the Pulley to the lower opening on the Front Press Base Repeat Procedure C above to install a Pulley F Draw the Cable around the Pulley to the lower opening on the Vertical Frame Repeat Procedure D above to install a Pulley Draw the Cable around the Pulley then downward G Attach the Cable to a Double Floating Pulley Bracket 16 Attach a Pulley to the Bracket Secure it with one M10 x 1 34 Allen Bolt
20. sher Qty 4 O 29 D shaped Washer Qty 4 21 1 8 Spacer Oty 4 mm D123 4 5 6 7 8 9 10 11 12 13 14 16 HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size 93 M8 x 3 Allen Bolt Qty 1 IT mm 92 M8 x 2 3 Allen Bolt Qty 2 m 91 M8 x 1 3 Allen Bolt Oty 4 mn 90 M8 x 3 Allen Bolt Qty 24 89 Hook Qty 6 GE Zn zu 88 Short Chain Qty 2 SE 87 Long Chain Qty 1 l gt oc 84 3 4 Leg Press Axle Qty 1 83 M12 x 2 3 Allen Bolt Qty 1 0 23 465 6 7 8 9 10 11 12 13 14 18 HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size OTT mw 104 M12 x 3 3 Allen Bolt Qty 1 Em 103 M10 x 5 An Allen Bolt Qty 2 GA 102 M10 x 4 3 Allen Bolt Qty 1 OT mw 101 M10 x 3 3 Allen Bolt Qty 1 100 M10 x 3 3 Allen Bolt Qty 6 mw 98 M10 x 3 Allen Bolt Qty 8 97 M10 x 2 2 Allen Bolt Qty 9 Em 96 M10 x 2 3 Allen Bolt Qty 2 95 M10 x 1 3 Allen Bolt Qty 15 mm 94 M10 x 37 Allen Bolt Qty 6 mm 01 2 3 4 5 6 7 8 9 10 11 12 13 14 15 HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size LD OC 111 M12 Aircraft Nut 110 M10 Aircraft Nut Qty 3 Qty 43 108 Y 1 Washer 109 M8 Aircraft Nut Oty 4 Oty 5
21. states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state IMPEX INC 14777 Don Julian City of Industry CA 91746 ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Service Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time www impex fitness com info impex fitness com When ordering replacement parts always give the following information Model Description of Parts Part Number Date of Purchase PONS 44
Download Pdf Manuals
Related Search