Image 831.159701 User's Manual
Contents
1. 15 16 17 18 Press a 50mm Square Outer Cap 17 onto each end of the Small Stabilizer 25 Attach the Small Stabilizer 25 to the Bench Frame 5 with two M10 x 65mm Carriage Bolts 40 and two M10 Nvlon Locknuts 11 Note There is an inden tation around the holes on one side of the Small Stabilizer This side must be facing the floor Press a 50mm x 70mm Outer Cap 10 onto each end of the Large Stabilizer 26 Turn the Large Stabilizer 26 so the warning decal is in the position shown Attach the Large Stabilizer to the Bench Frame 5 with two M10 x 65mm Carriage Bolts 40 and two M10 Nvlon Locknuts 11 Note There is an indentation around the holes on one side of the Large Stabilizer This side must be fac ing the floor Press two 20mm x 40mm Inner Caps 28 into each Backrest Tube 27 Press four 20mm x 40mm Inner Caps into the Backrest Adjustment Bracket 36 Lubricate an M10 x 180mm Bolt 22 Attach the Backrest Tubes 27 to the welded tube on the Backrest Adjustment Bracket 36 with the Bolt two M10 Washers 6 and an M10 Nylon Locknut 11 Make sure that the Backrest Tubes are turned as shown The indicated holes are not centered in the Backrest Tubes but are closer to one side Turn the Backrest Tubes so the holes are closer to the floor Do not over tighten the Nylon Locknut the Backrest Tubes must pivot easily Lubricate an M10 x 115mm Bolt 55 Slide an M102. Model No 831 159701 R1200A Ordering Replacement Parts The model number and serial number of your IMAGE 3 8 are list ed on a decal attached to the frame See the front cover of this Model No 831 159701 manual to find the location of the decal All replacement parts are available for immediate purchase or 9 special order when you visit your nearest SEARS Service QUESTIONS Center To request service or to order parts by telephone call the toll free numbers listed at the left If vou find that When requesting help or service or ordering parts please be you need help assembling or prepared to provide the following information operating the IMAGE 3 8 apart is missing e The MODEL NUMBER of the product 831 159701 or you need to schedule repair service call our toll free HELPLINE e The PART NUMBER of the PART see the PART LIST and the EXPLODED DRAWING at the center of this manual 1 800 736 6879 Monday Saturday 7 am 7 pm e The DESCRIPTION of the PART see the PART LIST and the Central Time excluding holidays EXPLODED DRAWING at the center of this manual e The NAME of the product IMAGE 3 8 weight bench REPLACEMENT PARTS If parts become worn and need to be replaced call the following toll free number 1 800 FON PART 1 8
3. 2 M10 x 115mm Bolt 55 1 5 2 M10 x 180mm Bolt 22 Assembly Before beginning assembly carefully read the following information and instructions Make Things Easier for Yourself This manual is designed to ensure that the weight bench can be assembled successfully by anyone By setting aside plenty of time and by deciding to make the task enjoyable assembly will go smoothly Assembly requires two people Place all parts in a cleared area and remove the packing materials Do not dispose of the packing materials until assembly is completed Tighten all parts as you assemble them unless instructed to do otherwise As you assemble the weight bench make sure all parts are oriented as shown in the drawings Before beginning make sure that you understand the information in the box above Note Some parts described in the assembly steps may be pre assembled Press a 50mm Square Outer Cap 17 onto each end of a Base 7 Turn the Base so the large hole is in the position shown Insert two M8 x 65mm Carriage Bolts 59 and two M10 x 65mm Carriage Bolts 40 up into the indicated holes in the Base Place the Base flat on the floor Turn the Base Crossbar 20 so the warning decal is positioned as shown Attach the Base 7 to the Base Crossbar with two M8 x 70mm Bolts 41 a Large Support Plate 12 and two M8 Nylon Locknuts 54 Do not tighten the Nylon Locknuts yet Press a 50mm Square Outer Cap 17 onto
4. Washer 6 onto the Bolt Hold the hole in the Backrest Adjustment Bracket 36 on the outside of the bracket on the Bench Frame 5 Inserting the M10 x 115mm Bolt 55 through the one side of the Backrest Adjustment Bracket one side of the bracket on the Bench Frame and through the 15mm x 10 2mm x 60mm Spacer 57 Then insert the Bolt through the other side of the bracket on the Bench Frame and the Backrest Adjustment Bracket Secure the Bolt with an M10 Washer 6 and an M10 Nylon Locknut 11 Do not over tighten the Nylon Locknut 11 19 20 21 22 Lubricate an M10 x 180mm Bolt 22 Attach the Backrest Tubes 27 to the indicated tube on the Bench Frame 5 with the Bolt two M10 Washers 6 and an M10 Nvlon Locknut 11 Note Do not over tighten the Nvlon Locknut the Backrest Tubes must pivot easilv Attach the Backrest 15 to the Backrest Tubes 27 with four M6 x 55mm Bolts 4 and four M6 Washers 30 Press a 25mm x 50mm Inner Cap 58 into the open end of the Seat Support Tube 37 Lubricate an M8 x 80mm Bolt 9 Attach the Seat Adjustment Bracket 45 to the indicated side of the Seat Support Tube 37 with the Bolt and an M8 Lubricate Nylon Locknut 54 Note Do not over tighten the Nylon Locknut the Seat Adjustment Bracket must pivot easily Place the Seat Support Tube 37 on the Bench Frame 5 so that the Seat Adjustment Bracket 45 fits over the welded pin not visible in the
5. 29 into each end of the welded tube on the Right Weight Glider 31 Slide the Right Weight Glider 31 onto the right end of the Barbell 85 Secure the Weight Glider to the Barbell with a hand tightened M8 x 20mm Screw 50 Make sure that the Weight Glider is turned as shown in the drawing 11 Identify the Left Safety Spotter 24 by the position of the handle and the Left Spotter Hook 62 Place the Left Safety Spotter on the left Base 7 so it is cen tered over the indicated hole Have a second person hold the Locking Bar 34 so that the Left Weight Glider 32 rests on top of the Left Safety Spotter 24 Insert a Weight Guide 18 into the Left Weight Glider the Left Safety Spotter and the hole in the Base 7 Note Tilt the Weight Guide away from the Upright 1 as you insert it Attach the Weight Guide 18 to the Base 7 with an M8 x 60mm Bolt 39 two M8 Washers 52 and an M8 Nylon Locknut 54 Do not tighten the Nylon Locknut yet 12 13 14 Place the Right Safety Spotter 23 on the right Base 7 and center it over the indicated hole Note The handle must point toward the center of the bench Have a second person hold the Locking Bar 34 so that the Right Weight Glider 31 rests on top of the Right Safety Spotter 23 Insert a Weight Guide 18 into the Right Weight Glider the Right Safety Spotter and the hole in the Base 7 Note It may be neces sary to tili the Wei
6. exercise aon Faw aw om O To do this stand in front of the cage and grip the Locking Bar 34 with both hands Turn the Locking Bar until the two hooks disengage the slots in the Uprights 1 Move the Locking Bar to a new position and turn the Locking Bar until the hooks engage the slots in the Uprights Note Always start an exercise with the barbell posi tioned at the lowest point to which it will move during the exercise Position both Safety Spotters 23 24 directly under the Weight Gliders 31 32 USING THE SAFETY SPOTTERS To move a Safety Spotter 23 24 not shown to a new position grip the handle on the side of the Spotter Hook 61 62 not shown and pull the Spotter Hook out of the slot in the Upright 1 Raise or lower the Safety Spotter to a new position and turn the Spotter Hook until it engages one of the slots in the Upright A WARNING Always set both Safety Spotters at the same height ATTACHING WEIGHTS TO THE BARBELL To use the Barbell 35 slide the desired amount of weight not included onto each end of the Barbell Secure the weights with the Large Weight Clips 13 Note To use standard weights the Weight Adapters 33 should be removed from the Barbell Attach weights to the Barbell with the Small Weight Clips not shown AWARNING Do not place
7. 00 366 7278 SEARS ROEBUCK AND CO HOFFMAN ESTATES IL 60179 Full 90 Day Warranty For 90 days from the date of purchase if failure occurs due to defect in material or workmanship in this SEARS WEIGHT BENCH EXERCISER contact the nearest SEARS Service Center throughout the United States and SEARS will repair or replace the WEIGHT BENCH EXERCISER free of charge This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for rental purposes This warranty gives you specific legal rights and you may also have other rights which vary from state to state SEARS ROEBUCK AND CO DEPT 817WA HOFFMAN ESTATES IL 60179 Part No 172630 R1200A Printed in China 2000 Sears Roebuck and Co
8. 6 6879 Monday through Saturday 7 a m until 7 p m Central Time excluding holidays To help us assist you please note the product model number and serial number before calling The model number is 831 159701 The serial number can be found on a decal attached to the weight bench see the front cover of this manual Before reading further please review the drawing below and familiarize yourself with the parts that are labeled Note The terms right side and left side are determined relative to a person sitting on the bench They do not refer to right and left on the drawings in this manual Left Side Upright Weight Storage Tube Adjustment Bracket Part Identification Chart Model No 831 159701 R1200A a Mn AA H M6 x 38mm Bolt 60 1 M6 x 55mm Bolt 4 4 il o wO ca M6 Washer 30 5 M6 x 16mm Screw 3 E LI O M10 Washer 6 eee O Lo M8 ae Locknut 54 11 M8 Washer 52 10 M10 Nylon Locknut 11 26 ANNINAN N A M8 x 70mm Bolt 41 4 M10 x 25mm Bolt 43 2 TID 5 G M8 x 65mm Carriage Bolt 59 M10 x 65mm Carriage Bolt 40 8 AY J GU li M10 x 65mm Bolt 42 4 Se MI kl MI HU UNAHAN KM GU M8 x 20mm Screw 50
9. 8 Washers 52 and two M8 Nylon Locknuts 54 Do not tighten the Nylon Locknuts yet DCG e 13 CD SE DP CI EI O O 4 Slide the remaining Brace 2 onto the bracket on the other Upright 1 Attach the Brace to the Upright with two M10 x 65mm Bolts 42 four M10 Washers 6 and two M10 Nylon Locknuts 11 Do not tighten the Nylon Locknuts yet Slide the Upright 1 and the Brace 2 onto the M10 x 65mm Carriage Bolts 40 and the M8 x 65mm Carriage Bolts 59 in the right Base 7 Attach the Upright with two M10 Nylon Locknuts 11 Attach the Brace with two M8 Washers 52 and two M8 Nylon Locknuts 54 Do not tighten the Nylon Locknuts yet 5 Press a 235mm Round Inner Cap 51 into the end of a Weight Storage Tube 21 While a second person holds a Crossbar 8 in the position shown insert two M10 x 70mm Bolts 46 through the bracket on the Weight Storage Tube 21 the left Brace 2 and the bracket on the Crossbar Thread an M10 Nylon Locknut 11 onto each Bolt Do not tighten the Nylon Locknuts yet DO O 6 Press a 25mm Round Inner Cap 51 into the end of the other Weight Storage Tube 21 While a second person continues to hold the Crossbar 8 insert two M10 x 70mm Bolts 46 through the bracket on the Weight Storage Tube 21 the right Brace 2 and th
10. Model No 831 159701 Serial No Write the serial number in the space above for reference VERA 3 O O DOO 7 HELPLINE 1 800 736 6879 SEARS ROEBUCK AND CO HOFFMAN ESTATES IL 60179 A CAUTION Read all precautions and instruc tions in this manual before using this equipment Save this L Visi r websi Sess isit our website at Q www imagefitness com new products prizes fitness tips and much more manual for future reference IMAGE 38 Table of Contents Important Precautions ooa ereket ns eaa eaa ee 3 Before You BeGIN i ev isa al fn a nara rs 4 Part Identification Chart eee eee 5 ASSOMDIY seprana sr thao a a l a art la eee l ark a 6 Adjusting the Weight Bench 00 ee 14 Ordering Replacement Parts 000 Back Cover Full 90 Day Warranty 00 Back Cover Note A Part List Exploded Drawing is attached in the center of this manual Remove the Part List Exploded Drawing before beginning assembly Important Precautions A WARNING To reduce the risk of serious injury read the following important precau tions before using the weight bench 1 Read all instructions in this manual before using the weight bench Use the weight bench only as described in this manual 2 ltis the responsibility of th
11. OKAON Qty Description Upright Brace M6 x 16mm Screw M6 x 55mm Bolt Bench Frame M10 Washer Base Crossbar M8 x 80mm Bolt 50mm x 70mm Outer Cap M10 Nylon Locknut Large Support Plate Large Weight Clip Seat Backrest Small Support Plate 50mm Square Outer Cap Weight Guide Small Weight Clip Base Crossbar Weight Storage Tube M10 x 180mm Bolt Right Safety Spotter Left Safety Spotter Small Stabilizer Large Stabilizer Backrest Tube 20mm x 40mm Inner Cap 38mm Bushing M6 Washer Right Weight Glider Left Weight Glider Weight Adapter Key No Qty MNNAOANNAWAH NNABRONNH HHH INS St ts st st ts st Description Locking Bar Barbell Backrest Adjustment Bracket Seat Support Tube M8 x 30mm Bolt M8 x 60mm Bolt M10 x 65mm Carriage Bolt M8 x 70mm Bolt M10 x 65mm Bolt M10 x 25mm Bolt Large Washer Seat Adjustment Bracket M10 x 70mm Bolt 50mm Bushing 25mm Bushing 45mm x 45mm Bushing M8 x 20mm Screw 25mm Round Inner Cap M8 Washer M10 x 25mm Bolt M8 Nylon Locknut M10 x 115mm Bolt M10 x 80mm Bolt 15mm x 10 2 mm x 60mm Spacer 25mm x 50mm Inner Cap M8 x 65mm Carriage Bolt M6 x 38mm Bolt Right Spotter Hook Left Spotter Hook User s Manual Exercise Guide 6mm Allen Wrench Note indicates a non illustrated part Specifications are subject to change without notice See the back cover of the user s manual for information about ordering replacement parts Exploded Drawing
12. drawing on the side of the Bench Frame Lubricate an M10 x 80mm Bolt 56 Attach the Seat Support Tube 37 to the indicated bracket on the Bench Frame 5 with the Bolt and an M10 Nylon ZI Locknut 11 Note Do not over tighten the Nylon bib ag ku f aN Locknut the Seat Support Tube must pivot easily Bl al 3 12 23 Turn the Seat 14 as shown Attach the wide end of the Seat to the bracket on the Seat Support Tube 37 with two M6 x 16mm Screws 3 Tilt the Seat Support Tube 37 upwards and attach the narrow end of the Seat 14 to the Seat Support Tube with an M6 x 38mm Bolt 60 and an M6 Washer 30 24 Make sure that all parts are properly tightened before you use the weight bench The use of all remaining parts will be explained in ADJUSTING THE WEIGHT BENCH starting on the following page 13 Adjusting the Weight Bench This section explains how the weight bench is adjusted See the included exercise guide for important informa tion about how to perform a variety of exercises and how to get the greatest benefit from your exercise program Inspect and tighten all parts each time you use the weight bench Replace any worn parts immediately The weight bench can be cleaned with a damp cloth and a mild non abrasive detergent Do not use solvents USING THE LOCKING BAR AND SAFETY SPOTTERS Before starting an exercise position the Barbell 35 and the Safety Spotters 23 24 in the correct position for that
13. e bracket on the Crossbar Thread an M10 Nylon Locknut 11 onto each Bolt Do not tighten the Nylon Locknuts yet 7 Have a second person hold the other Crossbar 8 between the Uprights 1 Attach the Crossbar 8 to the left Upright 1 with two M10 x 70mm Bolts 46 a Small Support Plate 16 and two M10 Nylon Locknuts 11 Do not tighten the Nylon Locknuts yet Attach the Crossbar 8 to the right Upright 1 with two M10 x 70mm Bolts 46 a Small Support Plate 16 and two M10 Nylon Locknuts 11 Do not tight en the Nylon Locknuts yet 8 Press a 25mm Bushing 48 into each end of the Locking Bar 34 Insert the Barbell 35 through the Locking Bar 34 until the Barbell is centered in the Locking Bar 9 Identify the Left Weight Glider 32 by looking at the position of the round tube Press a 38mm Bushing 29 into each end of the round tube on the Left Weight Glider 32 Slide the Left Weight Glider 32 onto the left end of the Barbell 35 Secure the Weight Glider to the Barbell with a hand tightened M8 x 20mm Screw 50 Look at the drawing on page 4 to make sure that you have correctly identified the left end The Left Weight Glider must be turned as shown in the drawing 10 Identify the Right Weight Glider 31 by looking at the position of the round tube Press a 38mm Bushing
14. e owner to ensure that all users of the weight bench are ade quately informed of all precautions 3 The weight bench is intended for home use only Do not use the weight bench in a com mercial rental or institutional setting 4 Use the weight bench only on a level surface Cover the floor beneath the weight bench for protection 5 Inspect and tighten all parts each time you use the weight bench Replace any worn parts immediately 6 Keep children under 12 and pets away from the weight bench at all times 7 Keep hands and feet away from moving parts 8 Always secure your weights not included with weight clips when they are mounted on the barbell 9 Always make sure there is an equal amount of weight not included on each side of the barbell 10 If you feel pain or dizziness at any time while exercising stop immediately and begin cool ing down 11 Always move the bench out of the way when performing an exercise that does not use the bench 12 13 14 15 Always set both safety spotters at the same height Always wear athletic shoes for foot protec tion while exercising The weight bench is designed to support a maximum of 560 pounds including the user a barbell and weights not included Do not place more than 310 pounds including the barbell on the weight gliders and safety spotters The decals shown below have been placed on the weight bench If a decal is missing or ill
15. each end of the other Base 7 Turn the Base so the large hole is in the position shown Insert two M8 x 65mm Carriage Bolts 59 and two M10 x 65mm Carriage Bolts 40 up into the indicated holes in the Base Place the Base flat on the floor Attach the Base 7 to the Base Crossbar 20 with two M8 x 70mm Bolts 41 a Large Support Plate 12 and two M8 Nylon Locknuts 54 Do not tighten the Nylon Locknuts yet For help identifying small parts use the PART IDENTIFICATION CHART on page 5 Note Some small parts may be pre assembled In addition to the included allen wrench assembly requires the following tools not included Two 2 adjustable wrenches One 1 rubber mallet One 1 standard screwdriver One 1 phillips screwdriver Lubricant such as grease or petroleum jelly and soapy water Assembly will be more convenient if you have the following tools A socket set a set of open end or closed end wrenches or a set of ratchet wrenches 3 Slide a Brace 2 onto the bracket on one of the Uprights 1 Attach the Brace to the Upright with two M10 x 65mm Bolts 42 four M10 Washers 6 and two M10 Nylon Locknuts 11 Do not tighten the Nylon Locknuts yet B ERER Slide the Upright 1 and the Brace 2 onto the M10 x 65mm Carriage Bolts 40 and the M8 x 65mm Carriage Bolts 59 in the left Base 7 Attach the Upright with two M10 Nylon Locknuts 11 Attach the Brace with two M
16. egible please call our toll free HELPLINE at 1 800 736 6879 Mondav through Saturdav 7 a m until 7 p m Central Time to order a free replacement decal Apply the decal in the location shown e Misuse of this product may result in serious injury e Read user s manual and follow all warnings and operating instructions prior to use e Do not allow children on or around machine e Replace label if damaged illegible or removed AWARN ING Before beginning this or any exercise program consult your physician This is especially important for persons over the age of 35 or persons with pre existing health problems Read all instructions before using SEARS assumes no responsibility for personal injury or property damage sustained by or through the use of this product Before You Begin Thank you for selecting the versatile IMAGE 3 8 weight bench The IMAGE 3 8 is designed to help you develop every major muscle group of the body Whether your goal is a shapely figure dramatic mus cle size and strength or a healthier cardiovascular system the IMAGE 3 8 will help you achieve the spe cific results you want For your benefit read this manual carefully before using the IMAGE 3 8 weight bench If you have additional questions please call our toll free HELPLINE Right Side Weight Guide Barbell Weight Glider Backrest Seat at 1 800 73
17. ght Guide away from the Upright 1 as you insert it Attach the Weight Guide 18 to the Base 7 with an M8 x 60mm Bolt 39 two M8 Washers 52 and an M8 Nylon Locknut 54 Do not tighten the Nylon Locknut yet Note If you are not planning to use Olympic weights with the weight bench you do not need to perform this step Keep the two Weight Adapters 33 in a safe place in case you need them in the future Fully engage the indicated hook on both sides of the weight bench before beginning this step Insert a 50mm Bushing 47 into the end of a Weight Adapter 33 With a second person holding the Barbell 35 so that it cannot turn use the allen wrench to secure the Weight Adapter to the Barbell with a Large Washer 44 and an M10 x 25mm Bolt 43 Note The Large Washer must fit into the indentation in the 50mm Bushing in the Weight Adapter Pull the remaining length of the Barbell 35 in the direction shown Next tighten the M8 x 20mm Screws used in steps 9 and 10 Attach the other Weight Adapter 33 to the other end of the Barbell in the same manner Attach the upper end of one of the Weight Guides 18 to the bracket on the Upright 1 with an M8 x 30mm Bolt 38 and an M8 Washer 52 Attach the other Weight Guide 18 to the other Upright 1 in the same manner Tighten all of the Nylon Locknuts used in steps 1 to 14 10
18. more than 260 pounds on the barbell Always secure the weights with weight clips when they are on the bar bell Always place the same amount of weight on each side of the barbell 14 ADJUSTING THE BACKREST To raise the Backrest 15 grip the end of the Backrest with one hand and pull it upward The Backrest Adjustment Frame 36 will automatically lock into one of the tabs on the bracket on the Bench Frame 5 To lower the Backrest 15 grip the end of the Backrest with one hand and pull it slightly upwards Grip the handle not shown on the right side of the Backrest Adjustment Frame 36 with your other hand and pull the Backrest Adjustment Frame free of the tabs on the bracket on the Adjustment Bench Frame 5 Lower the Backrest to the desired posi Bracket tion and lock the Backrest Adjustment Frame into the desired tab on the bracket on the Bench Frame ADJUSTING THE SEAT To raise the Seat 14 lift the narrow end of the Seat until the appropriate tab on the Seat Adjustment Bracket 45 engages the welded pin not shown on the right side of the Bench Frame 5 To lower the Seat 14 use the handle on the Seat Adjustment Bracket 45 to disengage the Seat Adjustment Bracket from the pin Lower the Seat to the desired position and engage the appropriate tab on the Seat Adjustment Bracket to the pin 15 Part List Model No 831 159701 R1200A Key No O DN DAD A
Download Pdf Manuals
Related Search