ILY Enterprise CoolCopy 7 User's Manual
Contents
1. 11 05 Setup Press ESC button to enter Startup Menu and Startup Menu ENT to enter the following figure Use the arrow button to select other function settings which will Startup Menu be the first setting to appear when the device is turned on 1 Copy Then press ENT i Copyright 2005 by ILY Enterprise Inc 21 AII Rights Reserved 4 11 6 Auto Verify This setting allows you to automatically verify if target CDs can be read after copying Press ENT button to enter the following figure 11 06 Setup Auto Verify Use arrow button to change the On or Off 3 setting Then press ENT or press ESC to go Auto Verify return to 11 06 menu Off 4 11 7 Auto Compare This setting allows you to automatically compare the source CD and target CDs after copying Press ESC button and arrow to enter setting 11 07 Setup Auto Compare Use arrow button to change On or Off setting Then press ENT to go back 11 07 menu Auto Compare Off 4 11 8 Auto Prescan This setting allows you to automatically scan if the source CD can be read correctly and also tests the reading speed Press ENT button to enter Auto Prescan 11 08 Setup Auto Prescan Use arrow button to change On or Off Setting Then press ENT or press ESC to return to 11 08 menu Off 4 11 9 Eject Disc Eject disc allows three choices Eject Good Only Eject All Disc and Do Not Eject Press ENT button to enter the following figure 1 1 092. amp Multi session CD Extra HFS CD Bridge ISO9660 CD R and CD RW Writing mode Auto Detect DAO TAO Copyright 2005 by ILY Enterprise Inc 4 All Rights Reserved Supported CD ROM Drives EPO TEAC Supported CD RW Drives Plextor TEAC Lite On Asus SONY Chapter 2 Installation Procedure When you receive the Coolcopy CD Duplicator the package could be packaged in the following ways controller only whole duplicator without writer installed and a complete duplication system 2 1 Controller only 1 Before the installation please prepare the necessary devices as following e CD ROM drive CD R RW drive IDE case 2 10 bay chassis suggested Hard drive and mobile rack IDE bus hard drive Option Switching power supply 300W suggested 2 After the preparation as above and make sure that e All IDE devices must be in master mode 2 2 Whole duplicator without writer installed e Unpack the package of the duplicators e Prepare the CD R RW writers according to the recommendation list Please check with the supplier about compatibility issues with unlisted CD R RW drives e Assemble the duplicator according to your need e Make sure that the voltage setting is correct 2 3 Completed duplication system e Take the duplication system out of the package e Check the entire unit to see if there are any problems e Make sure that the voltage setting is correct e The hard drive is optional Hardware Connection of
3. be rewritten raseaUopy Using arrow button to change Sel burn in num RunContinuous 1 10 10 100 100 1000 setting Press ENT or ESC button to go back 12 06 menu Run Continuous 4 12 7 Update Firmware This function will update your firmware to the latest version Insert the CD disc which contains the latest firmware data firmware CD disc into the CD ROM drive and the duplicator will find the data and update its firmware automatically During updating do not turn off the power of machine because the update will not be finished until machine resets itself The Update Firmware function updates firmware to the latest version 2 Unzip the firmware you have and write the file cdxxx bin into the root directory of a blank CD R or CD RW disc You have to close the session of the CD If the same CD disc still has capacity to add more data it can be used to store newer versions of firmware When updating the firmware program from the CD only the one from last session will be used Versions from previous sessions will be ignored Select source drive to CD ROM first Then 12 07 Adv Setup press ENT button to enter UpdateFirmware Update Firmware and ESC to exit Copyright 2005 by ILY Enterprise Inc 27 AII Rights Reserved System will search the new firmware from the CD and the LCD will show the process as left a When find the new firmware just press ENT Searc
4. Setup Eject Disc Use arrow button to select Eject Good Only Then press ENT or press ESC to return to 11 Eject Disc 09 menu Eject Good Copyright 2005 by ILY Enterprise Inc 22 AII Rights Reserved Use arrow button to select Eject All Disc then press ENT or press ESC to return to 11 Eject Disc 09 menu Eject All Disc Use arrow button to select Do Not Eject Then press ENT or press ESC to go back 11 09 menu Eject Disc Do Not Eject 4 11 10 Burn on the Fly This setting lets you controls the burning methods When the setting is On the data will copy directly from source drive to the target drives When the setting is Off the data will load into a partition of the hard drive first Then the copying will be completed Press ENT button to enter Burn On The Fly 11 10 Setup Use arrow button to change the On or Off Burn On The Fly Setting Then press ENT or press ESC to return to Burn On The Fly The 11 10 menu On If the system does not connect with hard drive the LCD will show the following message There is no HDD 4 11 11 Burn Mode This setting lets you control the burning methods There are two modes Disc At Once DAO or Track At Once TAO Default setting is DAO Some CD writers may support different writing methods If the method selected is not supported duplicator will automatically switch to the other one Press ENT button to enter Burn Mode 11 11 Setup Burn Mode Use a
5. into a particular partition as an image file Press ENT and arrow button to select the source 9 06 Image P A Image Src Drive Then use arrow button to select the disc as the master source Select Img Src 01 IDEO CD ROM After selecting the source press ENT LCD will show the source information the following info Load image from Drive ID 01 4 10 Edit Track Copyright 2005 by ILY Enterprise Inc 16 All Rights Reserved Function 10 Edit Track allows you to edit a collection of favorite songs from CDs You re able to collect different tracks or songs on a number of CDs and merge them onto a single CD This process can be divided up into four parts CD to CD CD to HDD Play Audio Track and Close Session f ion 10 Press ENT and use the arrow button to select function 10 10 Edit Track 4 10 1 CD to CD Edit Select CD to CD Edit to select one or more tracks from CD ROM and then copy onto blank CD R RWs Press ENT to change setting 10 01 Edit Track CD to CD Edit Follow the LCD to select the track that you want to edit Select Track 1 10 03 25 Press ENT to select the track After the track is selected the will appear beside 1 10 as shown Select Track Pressing ENT again will cancel the track 41 10 03 25 When the track selection is made use arrow button to move to the End manual Select Track as End 1Trk03 25 Press ENT to finish the disc editing Use arrow button SE to make a se
6. master If it works the CD ROM may be defective or not compatible with CD ROM 4 Buttons do not function e May be still busy on task e Button malfunction e Faulty board 5 Copy completed but CD R disc is not readable executable e Use the compare function to check e Change another CD ROM drive to test 6 The failure rate is high Lower the speed of the CD Writers and try again Quality of blank disc is poor Check for latest firmware version Check the CD Writer maximum writing speed If you want to copy at 24X writing process or higher please copy to hard drive first and then to CD 7 Can not boot up or failure to upgrade firmware e Contact your dealer to solve the problem Please note that ay be charged for this e Check to see if the BIOS program is correct since customers often download the wrong program or simply write the zipped file to CD when it should be first unzipped before writing e A failed upgrade might cause a failed boot This can only be solver by returning the control board to agent or factory directly It is not necessary to return whole system under failed upgrade Copyright 2005 by ILY Enterprise Inc 29 All Rights Reserved 8 Can not find the 12 Adv Setup function e Press ESC button for 2 seconds to enter the Adv Setup 9 To cancel the duplicator working process e Press ESC button for 2 seconds to cancel any Copy Test or Verify etc func
7. match Copyright 2005 by ILY Enterprise Inc AII Rights Reserved 4 6 Prescan Use the prescan function to scan if the source CD can be read correctly and also to test the reading speed Select function 6 Put the source CD into CD ROM 6 Prescan Press ENT to prescan LCD will show the scanning information as follows Scaning 24X 0 650 0MB 74 00 If the master of the disc can read correctly the source CD has no problems LCD will show the following If the master disc cannot be read correctly the LCD will show the message as follows PreScan Fail H D A O amp 2 O 4 7 Disc Info Function 7 Disc Info shows the basic information of the source CD Select Function 7 Insert source CD into CD ROM E 7 Disc Info Press the ENT button to show the disc information The LCD will show the total sessions and tracks on the master disc Total 02 Sessions Total 10 Tracks Press the ENT button again the LCD will show the total time and capacity on the master disc Total 74 00 Total 650 MB Press the ENT button again and use arrow button to select the session LCD will show the Session 01 information contained in the session Track 01 09 Press the ENT button again and use arrow button to select the track The LCD will then show what Track 01 information is contained on the track AUDIO 03 54 4 8 Select Source Function 8 Select Source will let you select the data on CD ROM CD writers
8. CD Duplicator CoolCopy Series enterprise Inc User s Manual CoolCopy1AL CD Backup CoolCopy 3 CoolCopy 7 Table of Contents Chapter 1 Introduction ees 4 fb Re p 4 1 2 FeatUF6S eic ttn eii a a c kd rix v ce a a a wo 4 1 3 Specifications iiri eda nici elenina 4 Chapter 2 Installation Procedure 5 2 1 Controller ul UN 5 2 2 Whole duplicator without writer installed 5 2 3 Completed duplication system 5 Chapter 3 Key Functions and Operating Instruction 9 Chapter 4 Re d ME 10 Reie E 10 e EES 11 4 3 Test CODY EE 11 LIA 11 AB COM Pal e 12 4 6 PIeSCali sucre d eo ire or RNV EUM QUAL ERR RN 13 4 7 DISC IMMO E 13 A B Select SOUICC M 13 4 9 MAJE 8s isininsstceseseseteseansccsdewetiecudersansdansedceecenanteansancndenddcwsssiscennentian 14 e WEE 14 49 2 Delete Images 14 4 9 3 IQ DIM node TTL 15 4 9 4 Compare Image saab 15 Ee Rn EE 16 4 9 6 Select SIC Drive scs alli ee Erb D ene ie 16 bla PX 16 4 10 1 CD to CD Edi ipei eter tig o rette cer apra 17 4102 CD to EE 18 4 T0 3 Play Audio Tracked 20 4 10 4 ee EE 20 emule T 20 4 11 1 Language optional rr dille aiar 21 411 2 B rti Speed cs edem ra odisea e pedet ten c
9. CoolCopy1AL CD Backup without a HDD CoolCopy1AL CD Backup Power Copyright 2005 by ILY Enterprise Inc 5 All Rights Reserved Hardware Connection with Hard Drive for Coolcopy3 Coolcopy 3 IDE 3 CD RW IDE 2 CD RW IDE 1 CD RW IDE 0 CD Rom HDD When the system connects with the hard drive the hard drive must connect on the IDE 0 port with the Master setting and the CD ROM must set at Slave Hardware Connection without Hard Drive for Coolcopy3 Coolcopy 3 IDE 3 CD RW IDE 2 CD RW IDE 1 CD RW IDE 0 CD Rom Copyright 2005 by ILY Enterprise Inc All Rights Reserved Hardware Connection with Hard Drive for Coolcopy7 Coolcopy 7 IDE 4 CD RW IDE 3 CD RW IDE 2 CD RW IDE1 CD Rom HDD IDE 8 CD RW IDE 7 CD RW IDE 6 CD RW IDE 5 CD RW Power Copyright 2005 by ILY Enterprise Inc All Rights Reserved When the system has a hard drive connected the hard drive must connect on IDE 0 port with Master setting and the CD ROM must set at Slave Hardware Connection without Hard Drive for Coolcopy7 Coolcopy 7 meas om mes mm Live om mei CD Rom IDE 8 CD RW IDE 7 CD RW IDE 6 CD RW Copyright 2005 by ILY Enterprise Inc All Rights Reserved Chapter 3 Key Functions and Operating Instruction pad eos LCD Display Panel Display main functions and all messages Scroll up through menus or functions Scroll down through menus or f
10. Yes 4 9 2 Delete Image If you want to empty an image file stored in a particular partition you can use the function Delete Image to do so 9 02 Image P A Select function by pressing arrow Delete Imaae Delete Image in The system will ask if you are sure you want to delete Partition A Yes Use arrow button to make Yes or No selection Copyright 2005 by ILY Enterprise Inc 14 AII Rights Reserved When the image is successfully deleted from the hard drive the LCD will show as follows Partition A Image is deleted 4 9 3 Image Info This function shows the basic information of an image file stored in a particular partition Press ENT to show the disc information The LCD will show the total sessions and tracks in the partition Total 01 Sessions Total 01 Tracks Press ENT again The LCD will show the total time and capacity in the hard drive of partition Total 650 MB Press ENT again and use arrow button S 1 to select the session LCD will show the information in ession 0 the session Track 01 01 Press ENT again and use arrow button to select the track LCD will show track information DATA 650 0MB 4 4 39v Oo I D E o CH Q o Q CO bes o 53 ZG CH e Oo O D D gt 4 9 4 Compare Image Use this function to compare the contents of the source CD and those of the image file in the partition First select the function by pressing the arrow 9 04 Image P A Pr
11. copying information as follows 3 Test amp Copy OK 03 When copying is completed the LCD will display as 1 Copy the following information OK 03 Discs correctly copied will be ejected automatically Copyright 2005 by ILY Enterprise Inc 10 All Rights Reserved and failed ones will remain in the writers 4 2 Test Function 2 Test will simulate the copying process When the simulation completes the discs will remain blank Press ENT button to start the disc simulation or press ESC to exit 2 Test If you use CD rewriteable discs that contains data the old Data will be quickly erased before before simulation begins LCD will show the following testing ei Information Testing 24X 0 650 0MB 74 00 When the process is finished the LCD will show the following message 2 Test OK 03 Stopping the test halfway does not affect the CD discs However if the CD rewriteable discs contain important data the information might be erased 4 3 Test amp Copy Function 3 Test amp Copy is to test first and then actually copy Select Function 3 Put a source CD into CD ROM And blank CD discs into writers 3 Test amp Copy Press ENT to start simulation LCD will show the Information as follows Testing 24X 096 650 0MB 74 00 After the tests finishes actual copying will begin Copying 24X 096 9 100049 650 0MB 74 00 When the entire process finishes the LCD will show the information as follows 4 Test a
12. e buttons on the drivers to take the failed CDs e During operation do not press any button interruption will harm the device CDs will be damaged 2 Without a hard drive installed If you don t install a 3 5 hard disc the operation procedures will be as follows e Insert the master disc to CD ROM e Switch to the Copy function by pressing arrow button Insert blank CD R or CDRW disc into all the CD writers Press ENT button to start e When Copy completes the passed CDs will eject automatically The default is to eject automatically but this can be changed e Failed CDs will remain in the writers The default setting is that failed CDs stay in the writers but you can change the setting You need to press the eject buttons on the writers to take the failed CDs ATA 66 Cable Layout Please identify two different kinds of cable before the hardware installation Chapter 4 Function 4 1 Copy Use this function to copy data from a source CD directly onto blank CD discs Before copying make sure that the source CD is insertd into CD ROM If you have a HDD make sure there is data in your HDD partition If you are not sure about the success of your duplication job you can use function 2 Test to simulate the copying process first Select function 1 Put a source CD into CD ROM and blank CD disks into CD writers CD rewriteable discs containing old data are usable too Copying 24X 096 650 0MB 74 00 LCD will show the process of
13. e the setting Then press ENT or ESC to go All data will be back to the 12 04 menu If the system does not connect with hard drive the LCD will show the message as follows There is no HDD lost format Yes 4 12 5 Verify HDD This function is to verify if the hard disc or any of its partitions are working well Press ENT to enter Verify HDD 12 05 Adv Setup Verify HDD Copyright 2005 by ILY Enterprise Inc 26 All Rights Reserved Use arrow button to change setting to Disk Then press ENT or ESC to go back to the 12 Verify Disk or 05 menu Partition Disk Use arrow button to change setting to Parti Then press ENT or ESC to go back to the 12 05 menu Verify Disk or Partition Parti 4 12 6 Burn in This function is a burn in test which will simulate the copying process multiple times After each cycle the CDs on the CD writers will be ejected automatically and re inserted again for continuous testing Press ENT button to enter Burn in and ESC to exit 12 06 Adv Setup Burn in The data will not be written on the blank CD discs and the discs will remain blank B p after the test urn in Test Using arrow button to change RunContinuous 1 10 10 100 100 1000 setting Press ENT or ESC button to go back 12 06 menu Sel burn in num Run Continuous The system will repeat to erase and write Burn in on the CD RW discs Only CD RW discs can E amp C
14. ess ENT and LCD will show the comparison Compare Image information as follows LCD will show the following screen Comp A 24X 0 650 0MB 74 00 When the process is finished the LCD will display the following message Compare OK 1 Fail 0 Diff 0 Press ENT to view the comparison details Src 01 CD ROM otal 650 0MB If the comparison is identical the LCD will Tgt 00 HDD P A show the following message E i g Identical Copyright 2005 by ILY Enterprise Inc All Rights Reserved 15 If comparison fails LCD will show the number of discs Compare OK 0 failed and succeeded Fail 1 Diff 0 Press ENT to see the comparison information Src 01 CD ROM Total 0 Bytes If the comparison fails the LCD will show the reason as follows Src 02 CD RW TOC not match 4 9 5 Select Partition This function is to select a partition in the hard disc Press ENT button to change the setting 9 05 Image P A Select Image After installing a hard disc duplicator will format it automatically Each partition occupies 1GB The number of partitions is dependent on the hard disc s capacity The partitions are alphabetically arranged Use arrow button to select which partition will be worked Select Working Partition A When the partition is set the LCD will show the i owe Set Partition to ollowing i 4 9 6 Select Src Drive This function selects CD ROM or any CD writer as the source from which you can load data
15. fault setting for optimal performance Press ENT button to enter the Setup function 11 Setup Copyright 2005 by ILY Enterprise Inc 20 All Rights Reserved 4 11 1 Language optional Here are the available languages on the LCD English Traditional Chinese Simplified Chinese and Japanese Press ENT to change the setting and ESC to 11 01 Setup exit Language 4 11 2 Burn Speed This setting controls the burning speed of CD writers Default setting is Auto which would use the highest available writing speed of the writer Press ENT to enter the setting 11 02 Setup Burn Speed Use arrow button to change the burning speed then press ENT Burn Speed 24X 4 11 3 Read Speed This function lets you control the reading speeds of target CDs Press ENT to enter the setting 11 03 Setup l Read Speed Use arrow button to change the reading speed then press ENT The default is maximum but other Read Speed choices are 32X 16X and 8X 32X 4 11 4 Auto Start Drive This function automatically tests or copies discs once you put the blanks discs into the writers Press ENT button to enter Auto Start Drive 11 04 Setup Auto Start Use arrow button to change the number or Off setting Then press ENT or ESC to Auto Start go back 11 04 menu Drive 4 11 5 Start up menu This setting lets you select any one of the functions except Adv Setup as the first item to appear on the menu when you turn on your device
16. hing F W button The system will update it XXX XXXXX 4 12 8 Compare Firmware This function will help you compare your current control firmware version and the updated version in your firmware disc that you insert into the CD ROM Press ENT button to enter Compare Firmware and ESC to exit 12 08 Adv Setup Compare Firmware 4 12 9 HW Diagnostic This function will detect which types of devices are connected with the control The LCD will show the hardware information Press the ENT button to enter HAN Diagnostic and ESC to exit 12 09 Adv Setup H W Diagnostic LCD will ask user to do the button test Following the LCD instruction test each function button v Enter ESC Hold ESC to exit After the button function testing the system will self test SDRAM the hardware connecting test and flash test Every testing process will be shown on the LCD It just takes a few minutes to get the results of hardware diagnostics It is an easy way to know if the system works properly When testing is finished the LCD will show the T finish Test finished message Press ESC button to est finished go back 12 09 menu 4 12 10 Load Default This function will reset whole previous setting back to factory s default setting Different settings will cause duplicator to react differently 12 10 Adv Setup Load Default Press ENT button to enter Load Default and ESC to exit Use the arrow button to cha
17. ien diene iano 21 211 5 Read Spoed reote e ut feme e acu endete eerie 21 4 11 4 Auto Start Drive ite ute e bee eere o Be ter aei 21 2 11 5 Startup MENU E 21 Copyright 2005 by ILY Enterprise Inc All Rights Reserved 4 11 6 Auto Verify tese n elena 22 EELER ee dee ee lena 22 211 9 AUI FOSCAIN WE 22 2 11 9 EE 22 4 11 10 Burn on The Fly diuidi oett hens 23 LAMENTO E 23 4 11 12 Button SOHO Lilla eno t eer ea lat 23 411 13 DEVICE Info ausi hop tr ice dicti oe xoc Doo oda 24 4 11 14 System Info etica ueque e RE i EE 24 d TT 15 Quick Erase cerano 25 4 11 16 UE 25 DER UC TT iii 25 4 12 1 Alpe period Eege 25 d 22 COVODBUPEY cea ie 26 4 12 95 Mead Error SKP niine dela diana 26 4 12 4 Format HardDisk alari FEY aue esa rat 26 4 12 5 Verity HDD alal 26 4120 Ed EI BEE 27 4 12 7Updalte Fiimware iecore Leslie Ra 27 4 12 8 Compare Firmware i 28 4 12 9 H W Diagnostic iaia 28 4 1210 toad Default E 28 Chapter 5 Troubleshooting 29 Copyright 2005 by ILY Enterprise Inc All Rights Reserved Chapter 1 Introduction 1 1 Overview People who want to create multiple copies of their CDs usually take a long time to do so They might not have enough CD RW drives or they might be using their computers for some other important tasks The duplication process noticeably slows down a computer during the burn process Rather than sit at the computer for hours duplicating discs one a
18. lection End edit disc and burn Yes Copying 24X Edit 1 10 1 1 LCD will show copying information as follows When copying ends the LCD will show the I Burn Complete message Bum Complete OK 03 System will ask if you want to continue editing Use the arrow button to make a selection Continue edit next Disc Yes If Yes is selected the source disc will be automatically ejected Insert another disc Insert next disc Follow the steps to select the track that you want to edit Then press ENT Select Track 2 10 04 25 When the track selection is made use arrow button to move to the End manual Select Track End 2Trk07 50 Press ENT button to finish the disc edition End edit disc Use the arrow button to make a selection and burn Yes Copyright 2005 by ILY Enterprise Inc 17 AII Rights Reserved Copying 24X Edit LCD will show copying information as follows 1 10 gt 2 2 The 2 2 means the second track of all tracks you have selected So far you have selected two tracks from two different CDs Burn Complete When copying is finished the LCD will show the OK 03 P following message The system will ask if you want to continue editing Use arrow button to select no then press Continue edit ENT next Disc No The system will ask to close the disc session ii Use arrow button to make Yes or No Close all disc s selection session Yes LCD will sh
19. mp Copy OK 03 4 4 Verify Function 4 Verify is to examine if the target CDs can be read correctly after copying Copyright 2005 by ILY Enterprise Inc 11 All Rights Reserved Press ENT button to verify LCD will shows as follows 4 Verify LCD will show verification information as follows Verify 24X 0 650 0MB 74 00 When the verification process is finished the LCD will display the result as follows 4 Verify OK 03 4 5 Compare Function 5 Compare is to make a comparison between the source and the target CDs after copying Select Function 5 Put the source CD into CD ROM and the target CDs into CD writers 5 Compare Press ENT to compare LCD will show the comparison information as follows Compare 24X 0 650 0MB 74 00 When comparison completes LCD will show as follows Compare OK 3 Fail 0 Diff 0 Press ENT button to see the details of source 1 If comparison is identical LCD Src 01 CD ROM will show the message as follows Total 650 0MB If the compare result is identical the LCD will show as follows Src 02 CD RW Identical If comparison fails LCD will show failure Compare OK 2 Fail 1 Diff 0 Press ENT button to see comparison information Src 01 CD ROM Total 0 Bytes If the comparison fails the LCD will show failure By pressing ENT twice LCD will show Src 02 CD RW the contents of source 1 and those of source 2 do not match as follows TOC not
20. n to the 11 13 menu pera PX W2410A 4 11 14 System Info This function shows the information of the system Press ENT button to enter the System Info and see the next information Press ESC to exit 11 14 Setup System Info The LCD shows Coolcopy3 as follows SST S9SF020 2001 11 16 CD Duplicator 1 3 ver 1 10B The LCD shows 7 Coolcopy7 as follows CD Duplicator 1 7 ver 1 10T WINBOND W49F002U 2001 11 16 Copyright 2005 by ILY Enterprise Inc All Rights Reserved 11 15 Setup 4 11 15 Quick Erase Quick Erase This function will quickly erase the data on the disc Press ENT button to enter the Quick Erase and ESC to exit Use arrow button to confirm whether you want to erase 3 the data Select the Yes or No setting Then press All data will be ENT or press ESC to return to 11 15 menu lost erase Yes LCD will show the information as follows Erasing disc 00 24 Quick When erasing disc function is finished the LCD will display as follows Quick Erase OK 01 Fail 00 4 11 16 Full Erase This function is to completely erase the data on the CD rewriteable discs Press ENT to enter the Full Erase 11 16 Setup Full Erase Use arrow button to select Yes or No Then press ENT or ESC to return to 11 16 menu All data will be lost erase Yes LCD will show the information as follows Erasing disc 03 24 Full When finished the LCD will show the message the Full Erase follo
21. nge settings When Load Default Yes is selected the duplicator will return to Config Yes factory s default setting Load Default The LCD message will show that the setting has OK been changed by with the follow message Copyright 2005 by ILY Enterprise Inc 28 AII Rights Reserved Chapter 5 Trouble Shooting 1 No display on LCD or the unit does not operate when power on e Please check the connection of power cable and that the power outlet is normal e Turn off the power of machine open the case of duplicator and check if there are any problems with the power cable 2 LCD shows the Error message e During operation like Copy Test Compare and Verify you may press ESC button to abort the operation An Error message will be shown no the LCD Some CD writers will cause the duplicator to reset and you have to re start the power to get the duplicator to function properly e A failed reading may cause an error message to show on the LCD display Change the master CD and try again e During operation if a read error buffer under run or writing error occurs the LCD will show error message like Pass xx failed xx e If there is no device connected and detected by duplicator during power on the duplicator will show an error message on the LCD before entering the main menu 3 CD ROM can not read disc and shows error message e Check the format of master CD or master CD itself for damage e Use any of the CD Writers to read the
22. or HDD as the source from which you intend to copy Copyright 2005 by ILY Enterprise Inc 13 All Rights Reserved 8 Select Source Select function 8 Press ENT and then use arrow button to select the Src CD ROM source 01 IDEO Slave After selecting source press ENT and LCD will show the following CD ROM selected Note Suppose you select HDD as the source and try to copy from one of its partitions but the partition contains no data An error message will then appear on your LCD From here you can switch to another partition that contains no data or use function 9 Image to load the data into the chosen partition first 4 9 Image Function 9 Image is only valid when you have installed a hard drive Select function 9 Press ENT 9 Image 4 9 1 Load Insert the master CD disc into the CD ROM or any one of the CD writers the duplicator will detect and analyze the master CD Here the Load function will allow you to load data from CD ROM or any CD writer into the current 9 01 Image P A partition of the hard disc P A means Partition A Load Press ENT to load LCD will then show the loading Load A 24X 095 inf ion information 650 0MB 74 00 When the image has successfully loaded the LCD will show the following Image load OK If there is an image file existing in current partition the system will ask whether you want to overwrite Image Exists Use arrow button to make a Yes or No selection Overwrite
23. ow the following screen E when you are closing the session Closing Session Please wait 4 10 2 CD to HDD This function lets you select one or more tracks from CD ROM and then copy the source into a certain HDD partition 10 02 Edit Track Press ENT to enter the setting CD to HDD Edit Follow the LCD to select the track that you want to edit Here 1 10 means the number one of 10 tracks Select Track and 3 25 means the playing time 110 03 25 Press ENT button to select the track After the Select Track track is selected the will appear Pressing 41 40 03 25 ENT again will cancel the track When track selection is made use arrow button to Select Track move to the End manual End 1Trk03 25 Press ENT to finish the disc editing Use arrow button to make a selection End edit disc and burn Yes The source will be loaded to hard drive LCD will show the loading information as follows ui de ali Edit gt When the Image Load is finished the LCD will show the message as follows Image load OK The system will ask if you want to continue editing Use the arrow Copyright 2005 by ILY Enterprise Inc 18 AII Rights Reserved button to make Yes or No selection 16 If Yes is selected the source disc will be automatically ejected Insert another disc Follow the steps to select the track that you want to edit Then press ENT button When the track selection is made u
24. rrow button to change TAO or DAO mode setting Then press ENT or press ESC Burn Mode to return to 11 11 menu DAO 4 11 12 Button Sound This setting allows you to control the sound when you press it 11 12 Setup Press ENT button to enter Button Sound Button Sound Use arrow button to change On or Off B setting Then press ENT or press ESC to return to utton Sound 11 12 menu On Copyright 2005 by ILY Enterprise Inc 23 AII Rights Reserved 4 11 13 Device Info This function shows the information of the CD ROM and any CD writer you have installed 11 13 Setup Device Info 00 IDEO Master Use arrow button to select the device or press CD ROM TEAC ESC to go back 11 13 menu Press ENT button to enter the device information Press ENT button to see the device information and ESC to return to the 11 13 menu CD 540E 3 0A Use arrow button to select another device or press ESC to return to the 11 13 menu 01 IDE1 Master CD RW PI FXTOR Press ENT button to see the device information and ESC to return to the 11 13 menu Sc PX W2410A Use arrow button to select another device or press ESC to return to the 11 13 menu 02 IDE2 Master CD RW PI FXTOR Press ENT button to see the device information and ESC to return to the 11 13 menu ui PX W2410A Use arrow button to select another device or 03 IDE2 Master ress ESC to return to the 11 13 menu j CD RW PLEXTOR Press ENT to see the information and ESC to retur
25. se arrow button to move to the End manual Press ENT button to finish disc editing Use arrow button to make a selection The track will be loaded as an image file onto hard drive LCD will the following information When loading is finished the LCD will show the message as follows System will ask you whether you want to continue editing Use arrow button to make a selection Select No to go next step System will ask you if you want to burn from the HDD onto CD R RW or move into a partition Selecting Burn will start the process LCD will show the copying information as follows When burning is finished the LCD will show the message as follows Selecting Move will move the data from the hard drive template to a certain partition Select the partition that the data will move into by pressing the arrow LCD will show the moving information as follows When moving is finished the LCD will show the message as follows If the chosen partition contains image data system will ask to overwrite it Select No to Continue edit next Disc Yes Insert next disc Select Track 2 10 04 25 Select Track End 2Trk07 50 End edit disc and burn Yes Load PO 24X Edit 1 10 gt 2 2 Image load OK Continue edit next Disc No Burn or Move to Partition Burn Copy PO 24X 0 1 2 Trk03 25 Burn Complete OK 03 Burn or Move to partition Move Select Partition Mo
26. t a time it is much more efficient to use a CoolCopy CD duplication system The Coolcopy CD Duplicator system is a standalone duplicator and does not need to be connected to a computer It can duplicate discs accurately and quickly With its multi function LCD panel Coolcopy CD Duplicator is easy for any user to operate It is a cost efficient CD R duplicator for audio data and video applications The simple control panel is designed to provide copy mode selection and copy operation 1 2 Features Standalone IDE to IDE CD Copy controller e 2 Coolcopy1 AL CD Backup 4 Coolcopy3 8 Coolcopy7 16 Coolcopy1 4 independent IDE channel Self system diagnostics when power on Supports Hard Drive image Auto format detection User friendly interface with message rich LCD display Fast copies supports high speed CD RW writing mode Easy operation without software and training are required Firmware upgrade via CD ROM 1 3 Specification Power requirement voltage 5VB 5 Current 0 5A Max Environment Temperature Operating 0 C to 70 C Storage 20 C to 85 C Humidity 15 to 90 Models Coolcopy3 coolcopy7 Dimensions Length 200 mm Width 146 2 mm Height 42 mm Connectors 40 pin internal IDE connector Cable Optional Using ATA 66 Cable of length do not use longer than 46cm CD Format CD ROM Mode amp Mode2 CD ROM XA Mode formi amp form2 CD DA Mixed Mode Video CD CD I Karaoke CD Photo CD Single
27. tion while the job is in progress Copyright 2005 by ILY Enterprise Inc AII Rights Reserved 30
28. unctions Execute the function which you select Cancel the function which you select After turning the power on the Coolcopy CD Duplicator will execute a self test for a few seconds After the self testing procedure runs the LCD will show 1 Coolcopy3 Coolcopy7 CD Duplicator CD Duplicator 1 3 ver 1 10B 1 7 ver 1 10T Two main operation procedures If you install a 3 5 hard disc the operation procedures is as follows 1 With hard drive installed Once duplicator detects a hard disc it will ask if you want to format or not A 10GB hard disc can be divided into 10 partitions Use the Select Source to set the hard drive as the target source Then select which partition to store the data in function 9 Image If there is no data stored in partition insert a source CD into CD ROM and use function 9 01 Load to transmit data from CD into selected partition by pressing ENT Different data can be stored in different partitions Switch to the Copy function by pressing the arrow button Insert blank CD R or CDRW discs into the CD writers Press ENT button to start copying Copyright 2005 by ILY Enterprise Inc 9 All Rights Reserved e When a Copy completes the passed correctly copied CD discs will be ejected automatically The default is to eject automatically but this can be changed e Failed discs will remain in writers The default setting is keeping failed discs in the writers but this can be changed Press th
29. ving to P A Q 3 Moving to P A OK Copyright 2005 by ILY Enterprise Inc AII Rights Reserved 19 keep the data image or Yes to overwrite it Image Exists Overwrite Yes LCD will show the moving information as follows Moving to P A 096 When moving is finished the LCD will show the Moving to P A message as follows OKI i 4 10 3 Play Audio Track This function allows your machine to be utilized as a music player Plug in an AV terminal in the audio port on the back of the device Press ESC and the arrow button to enter the play audio function 10 03 Edit Track Play Audio Track Use arrow button to select track you are going to play Select Track 1 10 03 25 Press ENT and LCD will display the playing information as follows Playing Track 1 00 00 03 25 4 10 4 Close Session Select Close Session will close the disc and restrict data writing This function allows discs to be read on any normal player Press ESC and arrow to select the function 10 04 Edit Track Close Session Press ENT the system will ask whether you want to close After this step data cannot be written onto the disc Close all disc s session Yes Closing Session LCD will show the message as follows Picasa wale When closing session is finished the LCD will Closi show the following message osing Complete 4 11 Setup This function allows you to change default settings It is suggested that you use de
30. wing message OK 01 Fail 00 4 12 Adv Setup This function allows you to change the system configuration Changes should be made only when you are fully familiar with the function To enter the function please press ESC button for 2 seconds 4 12 1 UnderRun Protect This function lets you control Buffer Under Run Protection settings such as Burn Proof SafeBurn JustLink Seamless Link etc 12 01 Adv Setup Press ENT button to enter UnderRun Protect UnderRun Protect Copyright 2005 by ILY Enterprise Inc 25 All Rights Reserved Use arrow button to change the setting Then press ENT or ESC to return to the UnderRun Protect 12 01 menu On 4 12 2 Overburn This setting lets you decide whether to copy beyond the limit of the CD or not Press ENT button to enter Overburn 12 02 Adv Setup Overburn Use arrow button to change the Overburn setting Then press ENT or ESC to return to the On 12 02 menu 4 12 3 Read Error Skip This function allows you to neglect any error that occurs during copying You can use this function to copy some defective CDs 12 03 AG Setup Read Error Skip Press ENT button to enter Read Error Skip Use arrow button to change the setting Then press ENT or ESC to go Read Error Skip back to the 12 03 menu Off 4 12 4 Format Hard Disk This function allows you to partition the hard drive Press ENT button to enter Format HDD 12 04 Adv Setup Format HDD Use arrow button to chang
Download Pdf Manuals
Related Search