Ikelite Olympus C-60 User's Manual
Contents
1. lite Digital Housing instruction manual fo r Olympus C 60 Housing 6 130 60 Ikelite Digital Housing instruction manual 6130 60 for Olympus C 60 Zoom Camera Congratulations on your purchase of an Ikelite Digital Camera Housing Ikelite has over 40 years of experience in the underwater photographic and lighting market Our products are designed and built in the USA by Ikelite for both the professional and amateur photographer The clear housing permits instant visual inspection of the camera and all sealing surfaces as well as complete monitoring of controls and camera LCD screens Ikelite Digital Housings are slightly negative in salt water for stability This housing has been water pressure tested at the factory Housing is pressure tested to 200 60m Opening the Housing 1 Lid Snaps have a Lock To open push Lid Snap Lock forward and lift as shown Keep pressure on the Lid Snap so it does not fly open quickly Some lid snaps have a lot of spring tension once they go over center have a firm grip on the lid snap Lid Snaps may be opened one at a time Push Forward Installing the Camera Remove the back from the housing The mounting tray O Ring for the camera is secured to the v housing back Hook Position the camera on the tray and secure it with the mounting bolt which threads into the camera s tripod socket Lens Barrier Mounting Tray Mo2. require no maintenance other than rinsing in fresh water after saltwater use If a push button control becomes difficult to push or if it sticks when depressed soak the housing in luke warm fresh water After a few minutes operate the push button If this does not correct the problem return the housing to Ikelite for maintenance lubricate shaft housing O pull out to expose shaft Some of the controls have long shafts These controls can be pulled out exposing the shaft see drawing To lubricate the control gently pull on the knob until the stainless steel shaft is exposed Lightly lubricate the shaft then move the shaft in and out several times This will lubricate the x ring in the Ikelite control gland This should be done before using the housing after a prolonged storage period or once a week when the housing is in use 15 Control Maintenance Cont 3 Some of the controls have a short shaft and cannot be pulled out exposing the shaft for lubrication In the unlikely event one of these controls sticks or becomes difficult to operate you can remove the control from the housing and lubricate it or return the housing to Ikelite for maintenance To remove the control loosen the set screw in the knob allen wrench reguired remove the knob If there is salt or dirt build up on the exposed control shaft clean the shaft Open the housing and gently slide the control shaft out of the control gland Clean and lightly lubricat
3. cannot be available light use only not recommended for use with flash used with wide angle lenses The front of the lenses are so large they block the camera s flash To properly light subjects when using a wide angle lens an external strobe should be used Due to the wide angle of coverage of these lenses the DS125 Substrobe is recommended or two DS51 Substrobes Wide Angle Adapter Tray with Release Handle 9523 31 Tray and Release Handle is required to mount external wide angle lens Substrobes 10 11 Optional Accessories Optional Accessories E Substrobe Substrobe DS51 Package 3944 54 255 Substrobe DS125 Package 3944 77 J The Substrobe DS51 package includes N The Substrobe DS125 package the Substrobe DSs51 the EV Controller and ball socket arms The EV Controller provides 10 manual power settings in 1 2 stop increments An external strobe offers several advantages over using the camera s built in flash External strobes move the flash away from the camera lens which helps reduce backscatter They also expand lighting options to achieve the best lighting for different subjects A second external digital strobe package can be added to fill the shadows and produce more realistic photographs includes the Substrobe DS125 the EV Controller ball socket arm and charger The EV Controller provides 10 manual power settings in 1 2 stop increments An external strobe offers several advantages over us
4. e the shaft including the end of the shaft Slide the shaft back into the control gland and gently slide it back and forth a few times without fully removing the shaft from the gland Replace the knob NOTE the flat area on the shaft the set screw in the knob should tighten down against the flat area on the control so the knob does not turn on the shaft housin control i gland shaft Loosen set screw allen wrench required Flat Tighten set screw down against this area when replacing the knob Lubricate end of shaft before reinserting into gland 16 General Tips 1 Due to the power required to operate the camera flash and LCD screen it is a good idea to start each dive with a fresh set of batteries Some cameras reset their flash to AUTO when the camera is turned on If you prefer another setting be sure to select it As soon as you enter the water take a moment and check the housing to see that it is properly sealed Next check to see if there are any bubbles on the face of the lens port If there are take your finger and remove them If there are bubbles on the lens port they can produce soft focus spots in your photographs NOTE 5 If you are shooting with the camera s built in flash and the cameras lens set to widest angle you may need to zoom the lens slightly or a shadow may appear in the lower left corner of close up photographs The lens port may block some of the light You can test this ab
5. f purchase Defective products should be returned prepaid to Ikelite Ikelite will at its discretion repair or replace such products and will return to customer prepaid All other claims of any nature including but not limited to bulb failure are not covered Except as mentioned above no other warranty expressed or implied applies to this Ikelite product Returning Products for Service Ikelite is most interested in preforming any service to assure that all products perform as intended For repair or service return the product to the address below with your name address phone number and a brief description of the problem Evidence of purchase date must be provided to obtain warranty service Ikelite Underwater Systems 50 W 33rd Street Indianapolis IN 46208 USA 317 923 4523 email ikelite ikelite com www ikelite com Digital 6130 60 01 0605
6. ing the camera s built in flash External strobes move the flash away from the camera lens which helps reduce backscatter They also expand lighting options to achieve the best lighting for different subjects A second external digital strobe package can be added to fill the shadows and produce more realistic photographs Ball Socket 4 Arm N Ball Socket Arm The Substrobe DS51 covers the The Substrobe DS125 covers the equivalent of a 28mm lens It is the equivalent of a 18mm lens 100 ideal choice when using only the degrees It is the ideal choice when camera lens or the camera lens with Ne using accessory wide angle lenses EV Controller a macro accessory lens greater than 28mm If an accessory wide angle lens wider NOTE NOTE than 28mm is used the ideal Optional Tray and Optional Tray and lighting choice is the Substrobe Release Handle Release Handle DS125 which covers 100 degrees or required to mount required to mount two Substrobe DSs1 s can be used Substrobes Substrobes 12 13 Maintenance The Ikelite Digital Housing should be given the same care and attention as your other photographic eguipment In addition to normal maintenance we recommend that the housing be returned to Ikelite periodically to be checked and pressure tested 1 Do Not leave the camera and housing in direct sunlight for prolonged periods Heat may damage the camera Do Not ship the camera in the housing Before using the housing alwa
7. ith a clean cloth Lubricant is not a sealant it is used to reduce friction Excessive lubricant can collect sand and dirt which may interfere with proper sealing CAUTION Diffuser and Deflector cont Never use spray lubricants as the propellant ingredient can cause the plastic housing to crack Diffuser Deflector A diffuser and deflector are E included with the housing The diffuser is white transparent plastic The deflector is also white but is not transparent and has a decal on the front This edge To install the diffuseror against Fort Clamp deflector spread the port housing Spring clamp at the spring end and slide over the lens port The white plastic should be Ss e placed in front of the camera lt gt flash The port clamp should be Spread to Install pushed back against the front of the housing Diffuser The diffuser should be installed when using the camera s built in flash When shooting with the camera s built in flash at approximately 2 feet 0 6 m or less the lens port on the housing may block a portion of the light from the camera s built in flash creating a shadow in the lower left of the photo If this occurs zoom the lens slightly to eliminate the shadow You can test this above water Deflector The deflector should be installed when using an external strobe such as the DS51 or DS125 Substrobe and EV Controller The deflector will redirect the camera s flash to the EV Controlle
8. o the camera lens The flash can light up any suspended particles in the water and they can be recorded in your picture This effect is called backscatter To eliminate as much backscatter as possible photograph close Photograph in clear water do not stir up the sand or silty bottom If backscatter becomes a problem in the environment you are photographing an external flash will help eliminate much of the backscatter Digital cameras have a slight lag time between when you press the shutter release button and the camera actually takes the picture Hold the camera steady a second or two after pressing the shutter release button Do not shoot down on subjects as they will guite often blend into the background and be difficult to see in the photograph Shoot subjects straight on or shoot upata slight angle using the blue water as a contrasting background Underwater flash is used to restore the warmer colors filtered out by the water as well as to illuminate the subject When photographing underwater set the camera to use flash on every shot If the camera s flash is set to AUTO and the sun is behind your subject the camera may see enough light that it does not fire the flash With the sun behind the subject the subject is shaded dark and needs flash for a good exposure continued on next page 18 Ikelite Limited Warranty All Ikelite products are warranted against any manufacturing defects for a period of one 1 year from the date o
9. ove water To shoot photographs closer than 2 feet 0 6m you need to use an external strobe such as the DS51 or DS125 With an external strobe you can position it so nothing blocks the light path between the strobe and the subject 17 Photo Tips Cont 6 When using daylight or flash if your camera consistently over or underexposes the image you may want to adjust your camera s exposure compensation settings Many cameras allow you to adjust both available light and flash exposure with an EV control in the camera s menu Many photographers transfer their images to the computer where they can fine tune the appearance of the image Many of the image manipulation programs make you think you can magically correct any image taken and make a good picture One thing to remember when using image manipulation programs if the image is overexposed much of the color is missing If the color is missing you cannot adjust it If images are slightly underexposed the color is there it is just dark and you can adjust it to some degree So if you error in exposure it is better to have the image slightly underexposed than over exposed 19 Photo Tips 1 The number one rule in underwater photography is eliminate as much water between camera and subject as possible Get as close as you can to the subject then use the zoom If you are using flash subjects beyond 6 feet 1 8m will not have much color The camera s built in flash is very close t
10. r which controls the external strobes output Lens Port Optional Accessories Treat the glass in the lens port as a camera lens After use rinse and gently dry the lens port to avoid water spotting To clean use a mild soap solution or lens cleaner Back O ring 0109 O rings last for several years if properly maintained See maintenance Always carry a spare Do not use alcohol or window cleaner on the Lens Port Wide Angle Adapter 9306 80 Reguired to mount Inon UWL 150AD Bayonet style wide angle lens The Lens Port will accept 2 Wide Angle Adapters The Wide Angle Adapter 9306 80 which is required to mount the Inon UWL 150AD Bayonet style wide angle lens The Wide Angle Adapter 9306 81 is reguired to mount the following Wide Angle Lenses Inon UWL 100 Sea amp Sea 458070 and Epoque DCL 20 screw thread 67mm style wide angle lenses These lenses can be secured onto the Wide Angle Adapter above or below water as they are designed to have water between the front of the port and the accessory lens Make sure Wide Angle Adapter 9306 81 Required to mount Inon UWL 100 Screw Thread 67mm style wide angle lens UR Pro Filter 6441 32 no air bubbles are trapped between the port and the accessory The UR Pro underwater color correcting filter is designed to lens Any vignetting that occurs can be eliminated by zooming restore some of the warm colors filtered out by the water For the camera lens slightly The camera s built in flash
11. ring Look through the clear plastic back at the o ring You should see a darkened area where the o ring is compressed against the housing back If you do not see an even black compression seal all the way around the back open the lid snaps reseat the housing back and close the lid snaps Visually check the seal again 5 Checking Controls Once the housing has been closed push the controls back into place Make sure they line up with the camera s controls Zoom Control NOTE After you have used the housing s zoom control it must be returned to the center position to disengage If the housing zoom control is pushing the zoom lever in either direction you cannot take a picture or access any other eo function as the camera is receiving a signal from the engaged zoom control Zoom control Zoom control engaged disengaged Turn Camera On Turn the camera on and operate each of the housing controls to get a feel for using the camera in the housing Take a few pictures above water with the camera in the housing Diffuser amp Deflector Installation Diffuser Housing shown with Diffuser installed Lubricants 1 Ikelite provides silicone lubricant with the housing We recommend you use only Ikelite lubricant on Ikelite products as some other brands may cause the o ring to swell and not seal properly Use only enough lubricant to lightly cover control shafts and o rings Wipe off any excess lubricant w
12. unting Bolt CAMERA MOUNT Open Camera Lens Barrier Before installing the camera into the housing Open the camera s lens barrier to turn the camera on Partly close the lens barrier to turn the camera off lens will fully retract Leave the Lens Barrier in this position when installing the camera into the housing The housings ON OFF Control can then be used to turn the camera on and off Front View Dack View Pad 2 Closing the Housing 1 Place housing face down in your lap or on flat surface 2 Check to see that there is an o ring on the housing back and housing that it is clean and in its proper OW location E I 3 Guide the back onto the housing TA u The o ring should touch the oring housing all the way around There should be an even gap all the way housing around between the housing and the housing back 4 Lift the lid snaps so they are extended and place the lid snap housing back into the hook on the housing A back 5 To close the housing push even gap down on the lid snaps until al Sides O they snap into place Lid Ll snaps on opposite sides of the housing should be closed at the same time Be sure they are down far enough to engage the lock Double check Once the housing is closed check the o ring seal Check the gap between the housing back and the housing it should be even all the way around housing o
13. ys check the tightness of the set screw in each control knob Check each control gland penetrating the housing to make sure they are tight There is a slight chance that either could vibrate loose during travel Keep the back o ring clean and lightly lubricated To lubricate remove the o ring from the back Put a small amount of Ikelite lubricant on your fingers Draw the o ring through your fingers to apply a light coating of lubricant Only apply enough lubricant to make the o ring feel slick Do Not stretch the o ring This light coating of lubricant will help to keep the o ring from drying out and will help to show a dark sealing line when the housing back is properly sealed Keep the area where the o ring fits and the sealing surface of the housing clean Rinse the housing exterior thoroughly in fresh water after each salt water use Dry with a soft cloth Dry lens port to eliminate water spotting After several uses in salt water soak the housing exterior in a mild soap solution rinse and dry before storage When storing the housing remove the back o ring lightly lubricate and place in a plastic bag Place the plastic bag with o ring inside the housing for safe keeping CAUTION Never use spray lubricants as the propellant ingredient can cause the plastic housing to crack 14 Control Maintenance Ikelite controls are designed to provide years of reliable service with minimal maintenance 1 Push button controls
Download Pdf Manuals
Related Search