Icom IF5061 User's Manual
Contents
1. O ICOM INSTRUCTION MANUAL VHF MOBILE TRANSCEIVER IC F5061 IC F5063 UHF MOBILE TRANSCEIVER IC F6061 IC F6O6G3 Icom Inc IMPORTANT READ ALL INSTRUCTIONS carefully and com pletely before using the transceiver SAVE THIS INSTRUCTION MANUAL This instruction manual contains important operating instructions for the IC F5061 IC F5063 IC F6061 and IC F6063 VHF UHF MOBILE TRANSCEIVERS EXPLICIT DEFINITIONS WORD DEFINITION AWARNING Personal injury fire hazard or electric shock may occur CAUTION Equipment damage may occur NOTE If disregarded inconvenience only No risk of personal injury fire or electric shock Z See the operating guide for details of BIIS MDC and LTR 47 system operations Ask your dealer for details SS Icom Icom Inc and the Tcom logo are registered trademarks of Icom Incorporated Japan in the United States the United Kingdom Germany France Spain Russia and or other countries LTR is a registered trademark of the E F Johnson Company All other products or brands are registered trademarks or trademarks of their respective holders PRECAUTIONS Z WARNING NEVER connect the transceiver to an AC outlet This may pose a fire hazard or result in an electric shock NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery This connection will ruin the transceiver NEVER cut the DC power cable between the DC plug and2. Push to pause scanning then resumes scanning after a specified time period has passed Push and hold this key for 1 sec to indicate the scan group then select the desired group using CH Up CH Down SCAN B START STOP KEY Push to start and cancel scanning operation Scan resumes after a specified time period has passed when scan is cancelled except for this key Push and hold this key for 1 sec to indicate the scan group then select the desired group using CH Up CH Down SCAN ADD DEL TAG KEY Push to add or delete the selected channel to from the scan group 1 Push to indicate the scan group then push CH Up or CH Down to select the desired group 2 Push to add or delete the channel to from the selected scan group 3 Push and hold for 1 sec to exit the scan group selection mode Push this key while scan is paused a signal is detected on a channel except for priority channel the channel is cleared from the scan group Y Depending on the setting the cleared channel is added Y to the scan group again after the scan is cancelled PRIO A B KEYS Push to select Priority A or Priority B channel Push and hold Prio A Rewrite or Prio B Rewrite to set the operating channel as the Priority A or Priority B chan nel MR CH 1 2 3 4 KEYS Push to select the memory channel 1 to 4 directly MONI AUDI KEY Mute and release the CTCSS DTCS or 2 tone squelch mute Open any squelch deactivat
3. e Minimum audio level is pre programmed O LED INDICATOR Lights red while transmitting a signal Lights green while receiving a signal UP DOWN KEYS CH Up CH Down Push to select an operating channel etc The desired function can be assigned by your dealer p 3 O POWER SWITCH O Push to turn the power ON and OFF e Automatic scan start Password prompt and Set mode access are available at power ON DEALER PROGRAMMABLE KEYS Desired functions can be programmed independently by your dealer p 3 Function display p 2 Speaker MICROPHONE CONNECTOR Connect the supplied or optional microphone f NEVER connect non specified microphones The pin Z assignments may be different and the transceiver may 7 be damaged MICROPHONE The supplied microphone has a PTT switch and a hanger hook e The following functions are available when the microphone is on or off hook depending on the setting Automatic scan start when on hook Scan is cancelled when off hook Scan is paused when off hook Automatic priority channel selection is available when off hook Sets to Inaudible condition mute condition when on hook Sets to Audible condition unmute condition when off hook E Function display n Yul LOW DD A amp SIGNAL STRENGTH INDICATOR Indicates relative signal strength level as below Y Y Y l Y l Weak Receive Signal leve
4. 5 Large speaker for good audio quality SP 10 For all round mobile operation SP 22 Compact and easy to install e HM 152 HM 152T HM 148 HAND MICROPHONE HM 152 Hand microphone HM 152T DTMF microphone HM 148 Heavy duty microphone e SM 25 DESKTOP MICROPHONE e UT 109R UT 110R SCRAMBLER UNITS Non rolling type UT 109R Rolling type UT 110R voice scrambler unit provides higher communication security e UT 96R 5TONE UNIT e UT 119H DIGITAL MODULATOR DEMODULATOR UNIT Provides 6 25 12 5 kHz narrow bandwidth digital mode operation SAFETY TRAINING INFORMATION Your Icom radio generates RF electromagnetic energy during transmit mode This radio is designed for and classified as Occupational Use Only meaning it must be used only during the course of employment by individuals aware of the hazards and the ways to minimize such hazards This radio is NOT intended for use by the General Population in an uncontrolled environment WARNING e For compliance with FCC and Industry Canada RF Exposure Requirements the transmitter antenna installation shall comply with the following two conditions 1 The transmitter antenna gain shall not exceed O dBi 2 IC F5061 The antenna is required to be located outside of a vehicle and kept at a distance of 48 centimeters or more between the trans mitting antenna of this device and any persons during operation For small vehicle as worst case the antenna shall be located on the
5. 50 duty cycle Transmitting more than 50 of the time can cause FCC RF exposure compliance requirements to be exceeded The radio is transmitting when the TX indicator lights red You can cause the radio to transmit by pressing the PTT switch Electromagnetic Interference Compatibility During transmissions your Icom radio generates RF energy that can possibly cause interference with other devices or systems To avoid such interference turn off the radio in areas where signs are posted to do so DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals aircraft and blasting sites MEMO MEMO Count on us A 6565D 1EX Printed in Japan 2006 2007 Icom Inc Icom Inc Bl 1 1 32 Kamiminami Hirano ku Osaka 547 0003 Japan rinted on recycled paper with soy ink
6. BIIS MDC and LTR y system operations Ask your dealer for details 1 BIIS operation only 3 LTR operation only gt wm 1 PANEL DESCRIPTION E Programmable function keys The following functions can be assigned to UP DOWN PO P1 P2 P3 and P4 programmable function keys Consult your Icom dealer or system operator for details con cerning your transceivers programming If the programmable function names are bracketed in the fol lowing explanations the specific key is used to activate the function depends on the programming CH UP AND DOWN KEYS w Push to select an operating channel w Push to select a transmit code channel after pushing TX Code CH Select Push to select a DTMF channel after pushing DTMF Autodial w Push to select a scan group after pushing and holding Scan A Start Stop Scan B Start Stop for 1 sec ZONE KEY Push this key then select the desired zone using CH Up CH Down zZ What is zone The desired channels are assigned into a zone according to the intended use for grouping For example Staff A and Staff B are assigned into a Business zone and John and Cindy are assigned into a y Private zone RUN SCAN A START STOP KEY w This key s operation depends on the Power ON Scan setting When the power ON scan function is turned OFF Push to start and cancel scanning operation When the power ON scan function is turned ON
7. can be used for password input The transceiver detects numbers in the same block as identical Therefore 01234 and 56789 are the same NUMBER 3 When the PASSWORD indication does not clear after inputting 6 digits the input code number may be incorrect Turn the power off and start over in this case 2 BASIC OPERATION E Channel selection Several types of channel selections are available Methods may differ according to your system set up NON ZONE TYPE Push CH Up or CH Down to select the desired operating channel in sequence or push one of MR CH 1 to MR CH 4 keys to select a channel directly ZONE TYPE Push Zone then push CH Up or CH Down to select the desired zone AUTOMATIC SCAN TYPE Channel setting is not necessary for this type When turning power ON the transceiver automatically starts scanning Scanning stops when receiving a call j co 2 BASIC OPERATION E Call procedure When your system employs tone signaling excluding CTCSS and DTCS the call procedure may be necessary prior to voice transmission The tone signalling employed may be a selec tive calling system which allows you to call specific station s only and prevent unwanted stations from contacting you Select the desired TX code channel 2 5 tone code or Talkgroup ID code according to your System Operator s instructions e This may not be necessary depending on programming e Refer to
8. edited e The digit to be edited blinks 4 Push CH Up or CH Down to set the desired digit 5 Push TX Code CH Select to set the digit The digit to the right will blink automatically 6 Repeat and to input all allowable digits 7 Push Call to transmit the edited TX code USING TX CODE ENTER KEY 1 After pushing TX Code CH Select push CH Up or CH Down or push TX Code CH Up or TX Code CH Down to select the desired TX code channel 2 Push TX Code Enter to enter the TX code edit mode e The digit to be edited blinks 3 Push TX Code Enter to select the desired digit to be edit ed 4 Push CH Up or CH Down to set the desired digit 5 Push TX Code Enter to set the digit The digit to the right will blink automatically Repeat and to input all allowable digits 7 Push Call to transmit the edited TX code O Talkgroup ID code selection Digital mode operation only If the transceiver has Talkgroup assigned to it the indication can be toggled between the operating channel name and the channel number and the Talkgroup ID name or ID code if the ID name is not programmed When the Talkgroup ID name or ID code is displayed CH Up or CH Down selects the desired Talkgroup ID name or ID code Push Talkgroup Talkgroup ID name or ID code appears Talkgroup ID name Appears above the key that Talkgroup is assinged after pushed When the 2 li
9. enter the memory channel selection mode then enter the desired channel number using the 10 keypad of the con nected microphone OPT 1 2 3 KEYS Push to control the output signal level from the optional unit connector j 1 PANEL DESCRIPTION O For Digital mode operation only TALKGROUP KEY Push to enter the talkgroup ID code selection mode Then select the desired talkgroup ID code using CH Up CH Down p 12 TX STATUS KEY Push to enter the Status message selection mode Then select the desired Status message using CH Up CH Down p 12 TONE RAN CH SELECT KEY While in the analog mode operation push to select the continuous tone channel using CH Up or CH Down to change the tone frequency code setting gt While in the digital mode operation push to select the RAN channel using CH Up or CH Down to change the RAN code setting While in the mixed digital and analog mode operation push to select the continuous tone channel using CH Up or CH Down to change the tone frequency code setting Then push this key to enter the setting After that the RAN channel selection screen appears Select the RAN channel using CH Up or CH Down to change the RAN code set ting Then push this key to enter the setting E Turning power ON 1 Push O to turn the power ON 2 If the transceiver is programmed for a start up password input the digit codes as directed by your dealer e The keys as below
10. i TABEE OF CONTENTS 2 S i 1 PANEL DESCRIPTION 2 a 1 7 A az 1 a A a ae natateata eevceeuatataans 2 E Programmable function keys _ uuuunnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnn 3 2 BASIC OPERATION cosa 8 14 TUNING POWEFON irren 8 E Channel selection 4444444444H0nnnnnnnnnnnnnnnnnn en nnnnnnnnnnn 8 BCallprocedu re cn stewie dane a e wen bolenta 9 E Receiving and transmitting oooooccccnnninininononcnnnncnnnnnnnnnnnnnnnnnnno 9 Transmitting MOSS Ra 10 TX code channel selection 444040n nennen nenn 10 O TX code number edit nnnnnnennnennnnnnnnnnnnn nen 11 Talkgroup ID code selection 22222u40n4nnn nennen 12 O TX Status message selection oooooccccccnnnooccnccccncnnnnnonononononos 12 DTMF transmission deiryd aiae a 13 E Scrambler T nelion esse ee 13 E User set Mode sire ete aang AE aa 14 3 CONNECTION AND MAINTENANCE cocccccccccccnoncnnannnnnnnnnos 15 17 E Rear panel connection nal 15 E Supplied Accessories cooccccccccccococcocononcccnnnnnnnrnrnrnnnnnnnnnnnn 16 E Mounting the transScCelVeT oooooooncccicinnccccccnonononnncnccnnnnnncnnononononas 16 BANEN n E coe ee A 17 E Fuse replacement sans 17 A e Mleumidtutnenndteas 17 HOBIONS Eee 17 4 SAFETY TRAINING INFORMATION ccccccceceesseeeeesnseeneeees 18 PANEL DESCRIPTION E Front panel O AF VOLUME CONTROL KNOB VOL Rotate the knob to adjust the audio output level
11. pgs 10 12 for selection Digital mode operation only 2 Push the call key assigned to one of the dealer program mable keys except for the Digital mode operation or PTT 3 After transmitting the remainder of your communication can be carried out in the normal fashion Selective calling Non selective calling aq 1133 PZ d Sessel ooo a oo 0 k OKODODO OS j Dosos EXA EXA ELE Da ID gt E Receiving and transmitting Receiving 1 Push to turn the power ON 2 Push CH Up or CH Down to select a channel in sequence 3 When receiving a call adjust the audio output level to a comfortable listening level Transmitting Wait for the channel to become clear to avoid interference 1 Take the microphone off hook e 2 5 tone mute may be released The audible condition is selected and BUSY indicator lights green e A priority channel may be selected automatically 2 Wait for the channel to become clear e The channel is busy when BUSY indicator l
12. provide clear communication TX CODE ENTER KEY PMR or BIIS PMR operation only Push to enter the ID code edit mode directly for both 5 tone and MSK Then set the desired digit using CH Up CH Down p 11 TX CODE CHANNEL SELECT KEY w Push to enter the ID code channel selection mode directly Then set the desired channel using CH Up CH Down p 10 During ID code channel selection mode push for 1 sec to enter the ID code edit mode for 5 tone and MSK Then set the desired digit using CH Up CH Down p 11 TX CODE CHANNEL UP DOWN KEYS w Push to select a TX code channel directly w Push to set the desired digit during the ID code edit mode ID MR SELECT KEY PMR or BIIS PMR operation only Recalls detected ID codes e Push this key then select the ID code using CH Up CH Down e Up to 5 ID s are memorized gt Push and hold for 1 sec to erase the selected D s HOOK SCAN KEY When the on hook scan function is activated push this key to disables on hook scan function stop scanning temporari ly Push this key again to re start scanning PANEL DESCRIPTION 1 USER SET MODE KEY Push and hold to enter user set mode e During user set mode push this key to select an item and change the value or condition using push CH Up CH Down Push and hold this key again to exit user set mode User set mode is also available via the Power ON function Refer to p 14 also MR CH ENT KEYS Push to
13. 0 000000000000000000000000 000000000000000000000000 000000000000000000000000 Mounting bracket Flat washers Bracket bolts and felts 2999 Spring washers Mounting screws e e e M5x1 2 Felts are already Nuts PUTE attached 00088 Self tapping screws M5x16 When using Used for labelling the programmable TER self tapping screws Felts reduce the vibration effects function keys according to their assin ged functions 2 Used for the optional unit installation Ask your dealer for details 3 CONNECTION AND MAINTENANCE E Antenna A key element in the performance of any communication sys tem is an antenna Contact your dealer about antennas and the best places to mount them E Fuse replacement A fuse is installed in the supplied DC power cable If a fuse blows or the transceiver stops functioning track down the source of the problem if possible and replace the damaged fuse with a new rated one UFuse rating 20 A USE the 20 A fuse only E Cleaning If the transceiver becomes dusty or dirty wipe it clean with a soft dry cloth AVOID the use of solvents such as benzene or A NOS alcohol as they may damage the transceiver sur faces E Options e RMK 3 SEPARATION KIT OPC 607 0PC 608 0PC 609 SEPARATION CABLE Allows you to install the transceiver main unit separately from the front panel for operating convenience e SP 5 SP 10 SP 22 EXTERNAL SPEAKER Input impedance 4Q Max input power 5 W SP
14. 3 CONNECTION AND MAINTENANCE E Rear panel connection O ANTENNA CONNECTOR D Sub 25 pin Antenna Connects to an antenna Connect an exter Contact your dealer about nal unit antenna selection and EXTERNAL placement SPEAKER JACK Connect a 4 8 Q external speaker Ir 640 8 DC POWER RECEPTACLE Connects to a 12 V DC battery Pay atten tion to polarities NEVER connect to a 24 V O MICROPHONE HANGER battery This could damage the transceiver Connect the supplied mi crophone hanger to the vehicle s ground for mi crophone on off hook functions See p 1 NOTE Use the terminals as shown below for the cable connections IGNITION LEAD FR Crimp Connects to a ignition line Solder A Do not put a pressure to A CAUTION NEVER remove to AS a the fuse holder from the DC Ss Binding to the DC power power cable S Sr cable is recommended CONNECTION AND MAINTENANCE 3 E Supplied Accessories E Mounting the transceiver ierenhang Microphone handen Microphone 0 dia bracket supplied with your transceiv and screw set hanger cable ey ANON ONES mounting l EN e Mount the transceiver securely with the 4 supplied screws Y to a thick surface which can support more than 1 5 kg LJ i i Ss Function name Sponges Flat washer stickers ar PN Cn Felt Spring washer O00000000000000000000000 00000000000000000000000
15. e any mute while push ing and holding this key LMR operation only Activates one of or two of the following functions on each channel independently PMR or BIIS PMR operation only e Push and hold to un mute the channel audio is emitted Audible condition e Push to mute the channel sets to Inaudible only e Push to un mute the channel sets to Audible only e Push after the communication is finished to send a reset code BIIS PMR operation only Y NOTE The un mute condition Audible condition may G automatically return to the mute condition Inaudible con 7 dition after a specified period depending on programming N PANEL DESCRIPTION 1 PUBLIC ADDRESS KEY Push to activate the Public Address PA function for voice amplification When the PA function is activated the audio output can be controlled from the transceiver separately with the VOL control knob e This function is available when the external unit such as a audio amplifier speaker etc is additionally connected Push this key then speak into the microphone while pushing and holding PTT CH Up CH Down also allow you to set the audio output level RX SPEAKER KEY The received audio can be heard via the external speaker when this key is pushed e This function is available when the external speaker is additionally connected e This function is useful when you are out of the vehicle e The audio outp
16. e transceiver has TX Code CH Select assigned to it the indication can be toggled between the operating channel number or name and TX code channel number or name When the TX code channel number or name is displayed CH Up CH Down selects the TX code channel USING TX CODE CH SELECT KEY 1 Push TX Code CH Select a TX code channel number or name appears 2 Push CH Up or CH Down to select the desired TX code channel 3 Push Call to transmit the selected TX code USING TX CODE CH UPY TX CODE CH DOWN KEY If the transceiver has a TX Code CH Up or TX Code CH Down key assignment the programmed TX code channel can be selected directly when pushed 7 NOTE for PMR or BIIS PMR operation e The LCD indication does not change when the operating h channel number or name is displayed Y e To check the selected TX code push TX Code CH Y Select SS 2 BASIC OPERATION TX code number edit PMR or BIIS PMR operation only If the transceiver has TX Code CH Select or TX Code Enter assigned to it TX code contents can be edited within the allowable digits USING TX CODE CH SELECT KEY 1 Push TX Code CH Select to enter the TX code channel selection mode e Select the desired channel before entering the TX code channel selection mode if necessary 2 Push TX Code CH Select for 1 sec to enter the TX code edit mode 3 Push TX Code CH Select to select the desired digit to be
17. fuse holder If an incorrect connection is made after cutting the transceiver might be damaged NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury NEVER allow children to touch the transceiver NEVER expose the transceiver to rain snow or any liquids USE the specified microphone only Other microphones have different pin assignments and may damage the trans ceiver DO NOT use or place the transceiver in areas with tem peratures below 30 C 22 F or above 60 C 140 F or in areas subject to direct sunlight such as the dashboard AVOID operating the transceiver without running the vehi cle s engine The vehicle s battery will quickly run out if the transceiver transmits while the vehicle s engine OFF AVOID placing the transceiver in excessively dusty envi ronments AVOID placing the transceiver against walls Otherwise heat dissipation will be obstructed AVOID the use of chemical agents such as benzine or alcohol when cleaning as they damage the transceiver sur faces BE CAREFUL The transceiver will become hot when operating continuously for long periods For U S A only CAUTION Changes or modifications to this transceiver not ex pressly approved by Icom Inc could void your authority to operate this transceiver under FCC regulations TABLE OF CONTENTS IMPORTAN rede i EXPEIGCIHBEPFINITIONS esse i PRECAUTION S A baren
18. ights green 3 Push CALL when initiating a call from your side e Coded audio may be heard from the transceiver then qn appears e This operation may not be necessary depending on your signal ing system Ask your dealer for details 4 While pushing and holding PTT speak into the micro phone at your normal voice level 5 Release PTT to receive Y IMPORTANT To maximize the readability of your signal 1 Pause briefly after pushing PTT 2 Hold the microphone 5 to 10 cm 2 to 4 inches from your mouth then speak into the microphone at a normal voice level MAAK O Transmitting notes e Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions The channel is in mute condition Inaudible condition 411 does not appear The channel is busy Un matched or matched CTCSS is received Depending on the pre setting Un matched or matched RAN is received Depending on the pre setting The selected channel is a receive only channel Digital mode operation only e Time out timer After continuous transmission for the pre programmed time period the time out timer is activated causing the transceiv er to stop transmitting e Penalty timer Once the time out timer is activated transmission is further inhibited for a period determined by the penalty timer BASIC OPERATION 2 TX code channel selection If th
19. ion type is equipped to all versions moreover the optional Rolling or Non rolling type can be available 1 Push Scrambler to turn the scrambler function ON e GD appears 2 Push Scrambler again to turn the scrambler function OFF e QD disappears E User set mode User set mode is accessed with User Set Mode and allows you to set seldom changed settings In this case you can customize the transceiver operation to suit your preferences and operating style Entering the user set mode 1 While pushing and holding P1 and P2 push to turn the power ON Then push and hold PO for 1 sec to enter user set mode e You should hold P1 and P2 until SET MODE appears POJ P1 P2 O 2 Push PO several times to select the appropriate item Then push Up or Down to set the desired level condi tion e Available set mode functions are Backlight LCD Contrast Beep Beep Level Ringer Level SQL Level AF Min Level Mic Gain Horn and Signal Moni PO Up Down BASIC OPERATION 2 3 Push and hold O for 1 sec to turn power OFF then ON again to exit set mode User set mode is also available via a programmable key Please refer to p 6 User Set Mode section DN
20. l Strong LOW POWER INDICATOR Appears when low output power is selected AUDIBLE INDICATOR Appears when the channel is in the audible unmute condition Appears when the specified 2 5 tone BIIS MDC code is received O COMPANDER INDICATOR Appears when the compander function is activated SCRAMBLER INDICATOR Appears when the voice scrambler function is activated PANEL DESCRIPTION 1 BELL INDICATOR Appears blinks when the specific 2 5 tone BIIS MDC code is received according to the pre programming CALL CODE MEMORY INDICATOR Appears when the call code memory is selected Appears when a phone call is received SCROLL INDICATOR Appears when the received SDM includes more than 12 characters SDM INDICATOR Appears when an SDM is received or a transmit SDM is selected ALPHANUMERIC DISPLAY w Displays an operating channel number channel name Set mode contents DIMF code etc w The indication mode can be selected from 1 line or 2 lines Ask your dealer for details e In this instruction manual the LCD illustration is described using the 2 lines indication mode ACTIVATED KEY INDICATOR Appears above the key assigned as Scan A Start Stopl Scan B Start Stop Scan Add Del Tag Lock Talk Around Surveillance Talkgroup and Digital keys during that key is activated 2 MDC operation only 4 Digital operation only Y See the operating guide for details of
21. nes indication mode is selected and Talkgroup is assigned to PO Push CH Up or CH Down to select the desired Talkgroup ID name or ID code 3 Push PTT to transmit the selected Talkgroup ID BASIC OPERATION 2 TX Status message selection Digital mode operation only If the transceiver has TX Status assigned to it the indication can be toggled between the operating channel name and the channel number and the Status message and the Status channel When the Status message and the Status chan nel is displayed CH Up or CH Down selects the desired Status message 1 Push TX Status Status message and Status channel appears Status channel Status message When the 2 lines indication mode is selected 2 Push CH Up or CH Down to select the desired Status message 3 Push PTT to transmit the selected Status message Only when the 2 lines indication mode is selected 2 BASIC OPERATION DTMF transmission If the transceiver has DTMF Autodial assigned to it the auto matic DTMF transmission function is available Up to 8 DTMF channels are available 1 Push DTMF Autodiall a DTMF channel appears 2 Push CH Up or CH Down to select the desired DTMF channel 3 Push DTMF Autodial to transmit the DTMF code in the selected DTMF channel E Scrambler function The voice scrambler function provides private communication between stations The frequency invers
22. nnel using CH Up CH Down After selecting the DTMF channel push again to transmit the selected DTMF code RE DIAL KEY Push to transmit the last transmitted DTMF code e TX memories are cleared after turning the transceiver OFF SCRAMBLER FUNCTION Push to toggle the voice scrambler function ON and OFF CALL KEYS Push to transmit a 2 5 tone BIIS ID code Call transmission is necessary before calling another station depending on your signalling system e Call A and or Call B may be available when your system employs selective Individual Group calls Ask your dealer which call is assigned to each key EMERGENCY KEYS Push and hold to transmit an emergency call When Emergency Single Silent or Emergency Repeat Silent is pushed an emergency call is transmitted with no beep emission and LCD indication change e f you want to cancel the emergency call push or push and hold the key again before transmitting the call e The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre setting SURVEILLANCE KEY Push to turn the surveillance function ON or OFF When this function is turned ON the beep is not emitted and the LCD backlight and the LED indicator do not light when a signal is received or a key is pushed COMPANDER KEY Push to toggle the compander function ON and OFF The compander function reduces noise components from the transmitted audio to
23. roof top at any place on the centre line along the vehicle in order to achieve 48 centimeters separation distance In order to ensure this distance is met the installation of the antenna must be mounted at least 48 centimeters away from the nearest edge of the vehicle in order to protect against exposure to bystanders 2 IC F6061 The antenna is required to be located outside of a vehicle and kept at a distance of 38 centimeters or more between the trans mitting antenna of this device and any persons during operation For small vehicle as worst case the antenna shall be located on the roof top at any place on the centre line along the vehicle in order to achieve 38 centimeters separation distance In order to ensure this distance is met the installation of the antenna must be mounted at least 38 centimeters away from the nearest edge of the vehicle in order to protect against exposure to bystanders 4 To ensure that your exposure to RF electromag netic energy is within the FCC allowable limits for occupational use always adhere to the fol lowing guidelines CAUTION DO NOT operate the radio without a proper antenna attached as this may damage the radio and may also cause you to exceed FCC RF exposure limits A proper antenna is the antenna supplied with this radio by the manufacturer or an antenna specifically authorized by the manufacturer for use with this radio DO NOT transmit for more than 50 of total radio use time
24. ut level is linked to the transceiver s volume control LIGHT KEY Push to turn the transceiver s backlight ON for about 5 sec when the backlight function is turned OFF in user set mode LOCK KEY Push and hold to electronically lock all programmable keys except the following Moni Audi Light Lock Call incl Call A and Call B Emergency Single Emergency Repeat incl Silent Surveillance and OPT 1 2 3 y al 1 PANEL DESCRIPTION HIGH LOW KEY Push to select the transmit output power temporarily or per manently depending on the pre setting e Ask your dealer for the output power level for each selection C TONE CH ENT KEY Push to select the continuous tone channel using CH Up CH Down to change the tone frequency code setting after push ing this key The selected channel remains set as the continu ous tone channel until another channel is designated as such TALK AROUND KEY Push to turn the talk around function ON and OFF e The talk around function equalizes the transmit frequency to the receive frequency for transceiver to transceiver communication WIDE NARROW KEY Push to toggle the IF bandwidth between wide and narrow e The wide passband width can be selected from 25 0 or 20 0 kHz using the CS F5060 CLONING SOFTWARE PMR or BIIS PMR opera tion only Ask your dealer for details DTMF AUTODIAL KEY Push to enter the DTMF channel selection mode Then select the desired DTMF cha
Download Pdf Manuals
Related Search