i. Tech Dynamic Clip R35 User's Manual
Contents
1. Steck i Tech Clip R35 A Tec amp CE FE Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment i Tech declares under our sole responsibility that the headset is in conformity with the provisions of the following Council Directives 1999 5 EC a Dispose of batteries according to local mmm regulations Do not dispose as household waste arene User Guide Bluetooth Declaration of Conformity ENGLISH We i Tech Dynamic Ltd declare that the following product Product Name i Tech Clip R35 Model No C51 A04104 XX Is in conformity with the following essential requirements of Council Directive 1999 5 EC referred to as R amp TTE Directive Article 3 1a 3 1 b and 3 2 and the product is manufactured in accordance with Annex II of above directive A copy of the Declaration of Conformity can be found at http www itechdynamic com Congratulations on selecting i Tech Clip R35 Headset Providing simple wireless connections to Bluetooth enabled mobile handsets your i Tech Clip R35 headsets offers you unrivalled freedom when marking and receiving calls while on the move or at the office This i Tech Cilp R35 headset is compliant with Bluetooth v1 2 specifications and compatible with mobile handsets that support Bluetooth Headset Handsfree A2DP or AVRCP Profiles Contents i Tech Clip R35 H2. once again to pause the music Volume Control Pressing the to increase the audio volume By Pressing the to decrease the audio volume Maximum audio level is 12 Forward Pressing gt gt to skip or select a new next chapter Backward Pressing lt lt to repeat or select a previous track Note To activate the AVRCP remote control feature your device must support AVRCP Profile Charging Your Headset Connect the charger to an AC wall outlet mains socket and the charger plug to the headset s charging socket fig 4 The LED will be red whilst charging IMPORTANT Charging indication will be delayed for a few seconds if the headset has not been used for a long time or the battery is drained Nominal Charging Time Th battery is normally fully charged within 3 hours When the battery is fully charged the LED will turn blue and remain on for 30 minutes Disconnect the charger from AC wall outlet mains socket and the headset Press and hold the MFB fig 1 for 2 seconds to turn the headset on please refer to Turning Your Headset On and Off on the next page Talk amp Standby Time The fully charged battery offers up to 6 hours talk time and up to 150 hours standby time When no calls are in progress the headset remains turned on in standby mode Low Battery When the headset is on and the battery becomes low the LED flashes red and the headset emits a beep every 1 minute Please recharge the batt
3. the headset is within a 10 meters range of your mobile handset s and there are no obstructions such as walls or other electronic devices in between If the above steps do not solve your problem please recharge the headset and remove your mobile handset battery for a short time If there is no reaction when pressing the buttons press the Reset Key fig 1 to return to factory default setting The headset is turned on again and all pairings are cleared The i Tech Clip R35 Headset is compliant with and adopts the Bluetooth Specification 1 2 However interoperability between the device and other Bluetooth enabled products is not guaranteed because it depends on compatibility For more information on the compatibility between the device and with other Bluetooth enabled products please check with the Manufacturer or browse http www itechdynamic com i Tech Clip R35 Headset Overview Forward Reverse Key Microphone ta ee l Multi function Button MFBVDual colour LED Volume Key Bult Buzzer ess in Rechargeable Battery Fig 1 Cs smmsereo Charging Socket Phone Jack Reset Key gt Fig 2 i Getting Started To use your i Tech Clip R35 headset the headset you are only required to follow these simple procedures Charge your headset Pair your headset with a Bluetooth enabled mobile handset Instructions on how to follow these procedures are detailed in this user guide Safety Informat
4. age describes a typical pairing procedures for Bluetooth enabled mobile handset Headset pairing procedures can vary depending on the type of model of your mobile handset Pairing Your Headset 1 Place the headset and the mobile handset where they are easily viewable and no more than 1 meter apart 2 Ensure the headset is turned OFF 3 Press and hold the MFB until the headset LED alternately flashes blue and red 4 Activate your mobile handset s Bluetooth function by referring to your mobile handset user guide for details 5 Set the mobile handset to search for Bluetooth devices within a 1 meter range as instructed in the mobile handset user guide and select i Tech Clip R35 from the list 6 Enter the preprogrammed passkey 8888 and press OK to pair your headset and mobile handset when the pairing is complete the headset LED will flash blue rapidly 5 times followed by a long beep 7 Go back to your mobile handset s main menu For certain mobile handset models a headset icon will be shown on the screen You should now be able to make and receive calls using your headset IMPORTANT If the pairing cannot be completed within 2 minutes whilst the pairing mode is activated the headset LED will flash purple red and beeps 3 times follawed by a olng beep before svitching off Please repeat Steps 2 to 7 to pair the headset and the mobile handset again Using Your Clip R35 Headset Answering a Call When there is an i
5. eadset Overview Getting Started Talk amp Standby Time Low Battery Turning Your Headset On and Turning the Built in Buzzer On and Off Pairing Your Headset Using Your Headset Answering a Call Answering a Call when Listening to Stereo Audio Ending a Call Rejecting a Call Dialing from Your Mobile Handset Voice Dialing from Your Headset Last Number Redialing from Your Headset Listening to Stereo Audio from your PC Adjusting the volume Resetting Removing the Pairin Remote Control Function Care and Maintenance Safety Informatio Troubleshooting Product Specifications Product Specifications Bluetooth Specification Version 1 2 Class 2 Bluetooth Profile Supported Headset Handsfree A2DP and AVRCP Range of Frequency 2 4GHz Spectrum Dimensions 55 L x 24 W x 27 H mm Nominal Charging Time Within 3 hours Talk Time Up to 6 hours Music Playing Time Up to 6 hours Standby Time up to 150 hours Weight 20 1 grams may vary due to users operation mode and mobile phone settings Troubleshooting If you are unable to connect your headset and mobile handset please try the following Ensure your headset is turned off and is properly charged Ensure the headset is paired with your mobile handset Ensure your mobile handset s Bluetooth feature is activated Please refer to your mobile handset user guide for specific instruction Ensure
6. ery as advised above Turning Your Clip R35 Headset On and Off Turning On the Headset Press and hold the MFB for 2 seconds until you hear a short beep The LED will flash blue IMPORTANT Please press the MFB each time you turn on the headset to reactivate pairing so that the connection between the headset and the mobile handset is resumed For pairing please refer to Pairing Your Headset on page 7 8 Turning Off the Headset Press and hold the MFB for 3 seconds until you hear a long beep The LED willstop flashing IMPORTANT To disconnect the Bluetooth connection you must first turn off your headset by pressing the MFB key Turning the Built in Buzzer On and Off Turning On the Built in Buzzer Press and hold the Volume for 2 seconds until you hear a long beep The LED flashes blue NOTE The built in buzzer is set to ON when proricked Turning off the Built in Buzzer Press and hold the Volume for 2 seconds until you hear 2 short beeps The LED flashes red Now when there is an incoming call the ringing tone will only be heard through one earphone Adjusting the Volume Push Up on the Navigation Key repeatedly to increasing the volume or push down on the Navigation Key repeatedly to decrease the volume Resetting Removing the Pairing You may wish to reset the headset to its original settings This will also clear all current pairings 1 Ensure the headset is OFF 2 Press and hold the Volume Key unt
7. il the LED alternately flashes blue and red 3 Release the Volume Key 4 Press and hold the Volume Key again until you hear 2 beeps Recharge the headset for a few seconds The headset is turned off and returns to the original settings All current pairings are cleared Using Your Clip R35 Headset Voice Dialing from Your Headset If your mobile handset is equipped with a voice dialing function simply press the MFB on your headset and when you hear a beep state the voice tag IMPORTANT Please make sure you have recorded the voice tags into the mobile handset before using voice dialing function Last Number Redialing from Your Headset Press the MFB on your headset twice IMPORTANT The above functions are only applicable to mobile handsets with Bluetooth Handsfree Profile Functionality varies depending on the mobile handset model you have Please refer to your mobile handset user guide for additional information Listening to Stereo Audio from Bluetooth A2DP Ready Device By connecting you headset to Bluetooth A2DP Ready Device you must first pair your headset with your device and activate the A2DP Service For further details regarding this prodecure please refer to the section of this user guide entitled Pairing your headset Pairing Your Headset Up to 1 meter S cm gt Prior to using your Headset for the first time you must pair it with a Bluetooth enabled mobile handset The information on the following p
8. in battery in accordance with the instructions contained in this user guide Avoid charging the headset in extremely high and low temperature Wearing Your Headset 1 Fig 3 Charging Your Headset ER Charging Socket Charger Plug A Fig 4 The Clip R35 Heheadset comes with a built in rechargeable battery Prior to using the headset for the first time it is recommended that you fully charge the battery Care and Maintenance Headset Consider turning your headset off before placing it in your pocket or bag If the MFB is accidentally activated your mobile handset may place an unintended call Do not expose the headset to liquid moisture or humidity as it is not waterproof Do not use abrasive cleaning solvents to clean the headset Do not expose the headset to extreme temperature conditions Do not dispose of the headset in a fire as it this may result in an explosion Do not bring your headset into contact with sharp objects as this will cause scratches and damage Do not stick anything inside the headset as this may damage the internal components Do not attempt to disassemble the headset as it does not contain serviceable components If you do not use the headset for long periods be sure to store it in a dry place free from extreme temperature conditions and dust Remote Control Function AVRCP Play Pause k Press once to play the music 2 Press
9. ion Check local laws regarding the use of mobile handsets and headsets whilst driving If you use the headset while driving ensure your attention and focus remain on the road and you drive in a responsible and safe manner Never allow children to play with the headset small parts may be a choking hazard Observe all signs that require an electrical device or RF radio product to be switched off in designated areas These could include hospitals blasting areas and potentially explosive environment Turn off your headset prior to boarding an aircraft Do not use your headset in an aircraft Never mount or store your headset over any air bag deployment area as serious injury may result when the air bag deploys Do not open or mutilate the built in battery Dispose of batteries according to local regulations Do not dispose as household waste Built in Battery Do not attempt to replace the headset s battery yourself as it is built into the headset and is non changeable Charge the battery in accordance with the instructions supplied with this user guide Charging Only use the manufacturer supplied charger when charging the headset Do not disassemble the charger as it may expose you to dangerous voltages and other risks Incorrect reassembly can cause electric shocks when the headset is subsequently used Do not use the charger outdoors or in damp areas Only charge the headset s built
10. ncoming call you will hear ringing through the earphone and the built in buzzer Press the MFB to accept the call or answer the call via your mobile handset in the normal way If you want to stop the buzzer from ringing press the Volume Key once You now only hear the ringing tone through the earphone Answering a Call when Listening to Stereo Audio Press the MFB once to answer the call and when finished press the MFB once again to resume stereo audio If the other party you are speaking to ends the call stereo audio will automatically resume without having to press the MFB NOTE To receive stereo audio from your mobile handset or PDA please make sure they support the Bluetooth A2DP profile Ending a Call Press the MFB to end your call or end the call via your mobile handset in the normal way Rejecting a Call To reject an incoming call press and hold the Volume Key for 2 seconds until you hear 2 beeps Dialing from Your Mobile Handset Simply make calls on your mobile handset in the normal way
Download Pdf Manuals
Related Search