Husqvarna Rider 15V2 User's Manual
Contents
1. 4 5 6 Check and adjust tyre pressure 60 kPa 0 6 bar 8 5 PSI f 8 9 Check that machine does not move in neutral 10 Check Forward drive Reverse drive Operation of blades Seat safety switch Lift lever safety switch Safety switch for the hydrostat pedals IU Doo eo 11 Check engine revs 2 900 100rpm 12 Tell customer about l Pre delivery Service carried out Need and benefits of following the service schedule No outstanding problems The need and advantages of leaving the machine for regular Certified service The effects of maintenance on the machine s second hand value Range of applications for BioClip 13 Complete proof of sale etc After first 8 hours 1 Change engine oil English 47 SERVICE JOURNAL Work done Date mileage stamp sign 48 English SERVICE JOURNAL Work done Date mileage stamp sign English 49 SERVICE JOURNAL Work done Date mileage stamp sign 50 English SERVICE JOURNAL Work done Date mileage stamp sign 114 01 39 95 UCL 2002w452. English 17 DRIVING 5 When the engine starts release the ignition key immediately back to neutral position IMPORTANT INFORMATION Do not run the starter for more than about 5 seconds at a time If the engine does not start wait about 15 seconds before trying again 6017 244 6 Push the choke lever gradually forward when the engine has started 7 Set the required engine speed with the throttle control Let the engine run at moderate speed or half throttle for 3 5 minutes before subjecting it to heavy load WARNING Never run the engine indoors in 6017 245 enclosed or poorly ventilated areas The exhaust fumes contain toxic carbon monoxide 18 English DRIVING Driving the machine 1 Release the parking brake by pressing down the brake pedal 6017 012 2 Carefully press down one of the pedals until the correct speed is reached To drive forwards press down pedal 1 To reverse press down pedal 2 6017 214A 3 Select the required cutting height 1 9 with the cutting height lever To obtain a uniform cutting height it is important that the tyre pressures are equal on both front wheels 60 kPa 8 5 PSI 6017 151 English 19 DRIVING 4 Push in the lock button on the lift lever and lower down the cutting unit IMPORTANT INFORMATION The service life of the drive belts increases considerably if the engine is run at low speed when engaging the blade
3. Cutting unit The Rider 15V2 can be fitted with three different cutting units Side ejector 970 mm 38 lt lt Combi 1030 mm 41 TC AN Combi 4120 mm 44 i See Maintenance Checking the Blades for identification of the cutting unit The combi deck functions as a mulching deck when a bio clip plug is mounted Without the plug the A deck will function as a rear ejection deck Lift lever for cutting unit The lift lever is used to set the cutting unit in transport or cutting position If the lever is pulled back the unit will lift up and the blades will automatically stop rotating transport position If the lock button is pressed and the lever is moved forward the unit will be lowered and the blades will automatically start rotating cutting position The lever can also be used to temporarily regulate the cutting height e g for a small mound in the lawn 6017 129 Lifting of the cutting unit transport position 7 gt way v r y S 3 NF Lg Lowering of the cutting unit cutting position 6017 130 English 15 PRESENTATION Lever for adjustment of cutting height With this lever the cutting height can be adjusted to 9 different positions Unit with side ejection 40 90 mm 1 9 16 3 9 16 Combi unit 45 95 mm 1 3 4 3 3 4 6017 131 Seat The seat has a jointed attachment on the front edge and can be tipped forward The seat can
4. Transport e The machine is heavy and can cause serious crush injuries Be especially careful when it is loaded in or out of a car or on and off of a trailer e Use an approved trailer to transport the 8010 061 machine Activate the parking brake and secure Regularly clean grass leaves and other debris from the the machine using approved fasteners such as machine tension belts chains or ropes when transporting e Check and observe local road traffic regulations before transporting or driving the machine on roads IMPORTANT INFORMATION The parking brake is not sufficient to lock the machine during transport Ensure you secure the machine firmly to the transporting vehicle Reverse the machine on to the transporting vehicle to prevent it from overturning 12 English PRESENTATION Presentation Congratulations on your choice of a top quality product which you will enjoy for many years These instructions describe the Rider 15V2 This rider mower is equipped with a 15 horsepower Kawasaki engine The power transmission from the engine is handled by a hydrostatic gearbox which allows variable variation of the speed by using the pedals There is one pedal for driving forwards and one pedal for reversing Location of the controls Ignition lock Choke lever Throttle lever Lifting lever cutting unit 1 2 3 4 Adjustment of cutting height 5 6 Speed limiter for reve
5. WARNING AN Observe caution to avoid trapping your hand 8 Lift off the drive belt 1 Then pull out the pin 2 6017 225 9 Pull the frame forwards and refit the pin 6017 226 10 Grasp the front edge of the cutting unit pull out and raise into the service position If the cylindrical bolt which is now holding the cutting unit is removed the cutting unit can be lifted off 6017 227 Restoring from service position To leave the service position reverse the procedures set out in Placing in the service position Make sure that the cutting unit s lug 3 enters the loop correctly on the underside of the machine see diagram 8009 438 38 English MAINTENANCE Checking the blades To achieve the best mowing results it is important that the blades are undamaged and well sharpened Check that the blades attachment screws are tight IMPORTANT INFORMATION Replacing or sharpening the blades should be conducted by an authorised service workshop The blades should be balanced after sharpening Damaged blades should be replaced when hitting E obstacles that result in a breakdown Let the servicing dealer judge whether the blade can be repaired ground or must be discarded IMPORTANT INFORMATION Combi unit 103 should always have the blades in the relative position shown inthe diagrams with an angle of 90 between the blades Otherwise the blades can go ag
6. environment and must in accordance with the law not be poured out on the ground or in the nature and must be handed in to a workshop or other designated station for treatment Avoid skin contact Wash with soap and water in the event of spillage Changing the oil filter Replace the oil filter every 200 operating hours Drain the oil first using the plug on the filter base Remove the old filter by turning it counterclockwise using an oil filter tool Lightly coat the rubber gasket with new oil and then install the filter by turning it clockwise until hand tight Tighten the filter an additional 1 2 turn Supply new engine oil as specified in Checking the engine s oil level Make sure the drain is reinstalled before starting the engine Start the engine for about 3 minutes and then stop and check for leakage 8009 454 Add oil to compensate for oil level drop due to oil filter capacity 42 English LUBRICATION Checking the transmission s oil level 1 Remove the transmission cover Loosen both screws one on each side and lift off the transmission cover 2 Check that there is oil in the transmission s oil tank Fill if necessary with engine oil SAE 10W 30 class SF CC 6008 240H Lubricating the belt adjuster The belt adjuster should be lubricated regularly using good quality molybdenum disulphide grease 1 nipple from the right hand side under the engine s lower belt pulley u
7. 60 kPa 8 5 PSI Lubricating the belt adjuster 3 Lubricate joints and shafts 3 Check the V belts Clean the hydrostat s cooling fins Check the transmission s oil level Adjust the brakes Check and adjust the throttle wire Check and adjust the choke wire Clean the engine s and hydrostat s cooling flanges Clean the foam element in the air filter Clean Replace the paper element in the air filter Check or clean the air intake screen Clean dust and dirt from cylinder and cylinder head fins Replace the fuel filter Clean and replace spark plugs Clean combustion chambers 3 Check and adjust valve clearence 3 Clean and lap valve seating surface 0000000 OO D First change after 8 hours Replace after every 50 hours with heavy loads or high temperatures Change the oil filter every 200 hours 3 For daily use of the machine lubrication should be conducted twice a week During dusty conditions cleaning and replacement should be more frequent Conducted by an authorised service workshop Replace the paper element yearly or every 200 hours Described in these instructions O Not described in these instructions WARNING No service procedures must be conducted on the engine or cutting unit unless e The engine is switched off e The parking brake is applied e The ignition key is removed e The cutting unit is disengaged e The ignition cable is removed from the plug 22 English MAINTENANCE Remo
8. cleaner case 3 Clean the foam element by washing it in detergent and water 4 Dry the foam element thorougly 5 Clean the paper element by tapping gently to remove dust If the element is very dirty replace it with a new one 8009 448 Always replace the paper element every 200 hours 6 Reinstall the foam element and the paper element into the air cleaner case 7 Reinstall the air cleaner case into the air cleaner body by putting the hooks on the bottom of the air cleaner case into the air cleaner body bottom 8009 450 8009 452 26 English MAINTENANCE Checking of the fuel pump s air filter Check regularly that the fuel pump s air filter is free from dirt The filter can when necessary be cleaned with a brush e Remove the screws and fold out the pump from the bracket No hoses are to be removed e Reinstall the pump to the bracket Check the level of the battery acid Check that the level of the battery acid lies between the markings Top up the cells with only distilled water WARNING Procedures on contact with acid External Rinse well with plenty of water Internal Drink large quantities of water or milk Contact a doctor as soon as possible Eyes Rinse well with plenty of water Contact a doctor as soon as possible Batteries emit explosive gas Sparks flames and cigarettes must absolutely not be brought into the vicinity of the battery Ignition system
9. is started with the engine cover opened or the protective covers removed AN WARNING The engine and the exhaust system become very hot during operation Risk of burn injuries if touched WARNING The battery contains lead and lead pollutants chemicals that are considered to cause cancer birth defects or other reproductive impairment Wash vour hands after touching the battery Do not smoke when carrying out maintenance 6003 009 English 11 SAFETY INSTRUCTIONS e Never use the machine indoors or in spaces lacking proper ventilation Exhaust fumes contain carbon monoxide an odourless poisonous and highly dangerous gas e Stop and inspect the equipment if you run over or into anything If necessary make repairs before starting e Never make adjustments with the engine running e The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer e The blades are sharp and can cause cuts Wrap the blades or wear protective gloves when handling them 8009 467 Never run the machine in an enclosed area e Check regularly that the parking brake works Adjust and maintain as required e The mulching unit should only be used where better quality mowing is required and in known areas e Reduce the risk of fire by removing grass leaves and other debris that may have fastened on the machine Allow the machine to cool before putting it in storage
10. not mix different types of oil Remember that using multi grade oils 5W 20 10W 30 and 10W 40 will increase oil consumption Check oil level more frequently when using them 8009 475 8009 159 20 C 10C OC 10 C LF 14F 32 F 50 F 68F 86 F 104 F 8009 140 English 41 LUBRICATION Changing the oil The oil should be changed for the first time after 8 hours of running time Thereafter it should be changed every 100 hours of running time With heavy loads or high temperatures replace the oil after every 50 hours WARNING Engine oil can be very hot if it is drained off directly after the engine is stopped Therefore allow the engine temperature to drop from hot to warm level first 1 Place a receptacle under the engine s drain plug located on the left hand side of the engine 2 Remove the dip stick and drain plug 3 Drain the oil run into the receptacle while the engine is warm 4 Fit the drain plug and tighten 5 Refill with fresh oil to the FULL mark on the dip stick The oil is filled in the same hole as for the dip stick See Checking the engine s oil level for filling instructions The engine holds 1 5 litres 1 6 USqt when oil filter is not changed and 1 7 litres 1 8 USqt when oil filter is changed 6 Run the engine warm and then check that there 8009 160 is no leakage from the drain plug IMPORTANT INFORMATION Used engine oil is hazardous to health and
11. tip over slope a A Drive very slowly without the cutting unit Keep hands and feet away from moving parts Speed limiter pedal forwards STARTING INSTRUCTION e READ OPERATOR S MANUAL e CHECK ENGINE OIL LEVEL e ENGAGE PARKING BRAKE AND LIFT CUTTING DECK IN TRANSPORT POSITION IF ENGINE IS COLD USE CHOKE e START THE ENGINE e RELEASE PARKING BRAKE BEFORE DRIVING Neutral Speed limiter pedal reverse Switch off the engine and take off the ignition cable before repairs or INSTRUCTIONS DE DEMARRAGE maintenance e LIRE LE GUIDE DE CONDUITE e VERIFIEZ LE NIVEAU D HUILE MOTEUR e SERREZ LE FREIN DE PARKING ET METTRE LE CARTER DE COUPE EN POSITION HAUT e SILE MOTEUR EST FROID UTILISEZ LE STARTER e ACTIONNEZ LE DEMARREUR e DESSERREZ LE FREIN DE PARKING 6 English SAFETY INSTRUCTIONS Safety instructions These instructions are for your safety Read them carefully WARNING AN The inserted symbol means that important safety instructions need to be observed It applies to your safety General use e Read all the instructions in this operator s manual and on the machine before you start it Ensure you understand them and then observe them e Learn how to use the machine and its controls safely and learn to how to stop quickly Also learn to recognize the safety decals e Only allow the machine to be used by adults who are familiar with its use e Make sure nobody
12. 0 030 Manufacture Tuff Torg K46 Oil SAE 10W 30 class SF CC Cutting unit Type 3 blade unit with side ejection Combi Cutting width Cutting heights Blade diameter 970 mm 38 1030 mm 41 Combi 1120 mm 44 Combi 9 positions 40 90 mm 1 9 16 3 9 16 45 95 mm 1 3 4 3 3 4 Combi 350 mm 13 3 4 Side 410 mm 16 1 4 Combi103 420 mm 16 1 2 Combi 112 When this product is worn out or no longer used it should be returned to the dealer or other appropriate body for recycling We reserve the right to change technical specifications without prior notice Note that no legal claims are valid on the basis of information in this manual Use only genuine parts for repairs The warranty is not valid if non genuine parts are used 46 English SERVICE JOURNAL Pre delivery service 1 Top up battery with acid and recharge for four hours 2 Fit steering wheel seat and any optional equipment 3 Adjust cutting unit Adjust the lifting springs the weight of the cutting unit should be 12 15 kg 26 5 33 lbs Only applies to Combi deck Adjust cutting unit so that rear edge is about 2 4 mm 1 8 higher than front edge Adjust cutting unit height setting so that cutting height limit is 5 mm 3 16 above the frame of the unit at the lowest cutting height Check that engine has correct amount of oil Check that the right amount of oil is in the transmission Connect battery Fill with fuel and start engine
13. 1 Put the unit in the service position see Placing in the service position 2 Remove the three screws holding the BioClip plug and remove the plug 3 Tip Fit three full thread screws M8x15 mm in the screw holes to protect the threads 4 Replace the unit in normal position Fit the BioClip plug in the reverse order 4 0 English Service position Removal of BioClip plug 8009 137a 6017 227 8009 289 LUBRICATION Checking the engine s oil level Check the oil level in the engine when the Rider stands horizontal and the engine is switched off Fold open the engine cover Release the dip stick and pull out Wipe off the oil and insert again without screwing it in The dip stick must be fully screwed down Pull out the dip stick Check the oil level The oil level should be between the markings on the dip stick If the level approaches the ADD mark top up with oil to the FULL mark The oil is filled in the same hole as for the dip stick Fill the oil slowly Tighten the dipstick correctly before starting the engine Start and run the engine at idling speed for approx 30 seconds Turn off the engine Wait 30 seconds and check oil level If necessary fill so that the oil comes up to the FULL mark on the dip stick The following engine oils are recommended e API Service Classification SF SG SH or SJ Choose the viscosity according to the temperatures in the picture Do
14. Children Tragic accidents can occur if the operator is not alert to the presence of children Children are often attracted to the machine and the mowing activity Never assume that children will remain where you last saw them 1 Keep children out of the mowing area and under the watchful care of another responsible adult 2 Be alert and turn machine off if children enter the area 3 Before and when backing look behind and down for small children 4 Never carry children They may fall off and be seriously injured or interfere with safe machine operation 5 Never allow children to operate the machine 6 Use extra care when approaching blind corners shrubs trees or other objects that may obscure vision AN 1 Safety rules for USA N Service Use extra care in handling gasoline and other fuels They are flammable and vapours are explosive a Use only an approved container b Never remove gas cap or add fuel with the engine running Allow engine to cool before refuelling Do not smoke c Never refuel the machine indoors d Never store the machine or fuel container inside where there is an open flame such as in a water heater 2 Never run a machine inside a closed area 3 Keep nuts and bolts especially blade 10 attachment bolts tight and keep eguipment in good condition Never tamper with safety devices Check their proper operation regularly Keep machine free of grass lea
15. Dirt in carburettor or fuel pipe Choking or incorrectly adjusted throttle cable Air filter clogged Spark plug defective Dirt in carburettor or fuel pipe Carburettor incorrectly set Choking or incorrectly adjusted throttle cable Engine overloaded Air intake or cooling flanges blocked Fan damaged Too little or no oil in engine Ignition defective Spark plug defective One or more cells faulty Bad contact between battery terminals and cables Blades are loose Engine is loose Imbalance on one or more blades resulting from damage or inferior balancing after sharpening Blades blunt Cutting unit skew Long or wet grass Grass blockage under hood Different tyre pressures on right and left sides Over speeding Drive belts slipping The blade has a broken break pin BioClip STORAGE Winter storage At the end of the season the machine should immediately be put in order for storage also if it is going to stand idle for more than 30 days Fuel which is left to stand for long periods 30 days or more can leave tacky deposits which can block the carburettor and interfere with the engine Fuel stabiliser is an acceptable alternative to avoid tacky deposits during storage Add stabiliser to the fuel in the tank or the storage container Always use the mixing ratios indicated by the manufacturer Run the engine for at least 10 minutes after adding the stabiliser so that it will reach the carburetto
16. FV Vs liisa itaalia 17 Before Starting ccccccsececeseeecceeeeecseeeesseeees 17 Starting the engine cccccssecesseeeeeeeseees 17 Driving the machine nmmnnennnnna 19 CUNO UDS a a a 20 Stopping the engine nnnnnneenna 21 Release lever nnnnnnunennnnnnnnnnt 21 Maintenance nmnmennenennnnennnannna 22 Maintenance schedule 1 22 Removing the machine hoods 23 Checking and adjusting of the steering wires 24 IMPORTANT INFORMATION Read carefully through the Operator s manual so that you know how to use and maintain the Rider before you use it Adjusting the brake mnnnennnnnni 24 Checking and adjusting the throttle wire 25 Checking and adjusting the choke wire 25 Replacing the fuel filter eennu 25 Replacing the air filter mmmernua 26 Checking of the fuel pump s air filter 27 Checking the level of battery acid 27 Ignition system assis sosaniastecisanniesetotanauheumtenencncaces 27 Inspecting the safety system 28 MaM FUSE RTS A 29 Checking the tyre pressure 29 Checking the engine s cooling air intake 29 Fitting the cutting unit mmennn 30 Removing the cuttin
17. Operator s manual Rider 15V2 Please read these instructions carefully and make sure i you understand them before using the machine English CONTENTS Operator s Manual for Rider 15V2 Safety rules for USA nunnnonannunnnnann a 2 Introduction mrmnnmnnnnnnmnn 4 Travel and transport on public roads 4 TONING skaalas ta e ika Suit 4 Intended use cs ferses scone veeshalcenivezeressdeevisesevedenniees 4 Serial NUMDET cccsseececsseceeeeecenceeeecssernecess 5 Explanation of symbols 6 Safety instructions mmmnnn 7 General Use eats ceacaneanasedieergeidciacecesacntesonenens H Driving on SIOPES is tiie a nanitain svad kass sada etsanie ta 9 ons 10 Maintenance nnmennnennanannne nunna 10 Transpor PEHMEMAD EMA AEA 12 Presentation mmmmnrnnnn 13 Location of the controls ennu 13 Throttle lever ccccseccssceceeecseecseeceeeseesaees 14 Choke lever imestan t nagi tada n aal 14 Speed limiter rnnmernnenenn nene 14 Parking brake ic s25reisct breonievewrvareedaunnonenceishacbewates 14 Cutting unit EMAEMA Ma 15 Lift lever for cutting unit cceecesseeeeeeeeees 15 Lever for adjustment of cutting height 16 Oedl eee eee eee linad tis ala ai 16 20721127 5 A AA mi 16 D
18. The machine engine brakes better in low gear e Take extra care if any attachments are fitted that can change the stability of the machine e Do not mow too close to edges ditches or Be especially careful when driving on slopes banks The machine can suddenly overturn if one wheel comes over the edge of a steep slope or a ditch or if an edge gives way 8010 054 e Do not mow wet grass It is slippery and tyres can lose their grip so that the machine skids e Do not try to stabilize the machine by putting your foot on the ground e When cleaning the chassis the machine must never be driven close to an edge or ditch e Follow the manufacturer s recommendations regarding wheel weights or counterbalance weights to increase stability English 9 SAFETY INSTRUCTIONS Children Serious accidents may occur if you fail to be on your guard for children in the vicinity of the machine Children are often attracted to the machine and mowing e Never assume that children will remain where you last saw them e Keep children away from the area to be mowed and under close supervision by another adult e Keep an eye out and shut off the machine if children enter the work area e Before and during reversing procedures look behind you and down for small children 8010 057 e Never allow children to ride along They can fall Never allow children to operate the machine off and seriously injure themselves or be in t
19. The engine is equipped with an electronic ignition system Only the spark plugs require maintenance For recommended spark plug see chapter Technical data IMPORTANT INFORMATION Fitting the wrong spark plug type can damage the engine 1 Remove the ignition cable shoe and clean around the spark plug 2 Remove the spark plug with a 3 4 19 mm spark plug socket wrench 3 Check the spark plug Replace the spark plug if the electrodes are burned or if the insulation is cracked or damaged Clean the spark plug with a steel brush if it is to be reused 4 Measure the electrode gap with a gapping tool The gap should be 0 75 mm 0 030 Adjust as necessary by bending the side electrode 8009 147 6008 013 IMPORTANT INFORMATION Inadequately tightened spark plugs can cause overheating and damage the engine Tightening the spark plug too much can damage the threads in the cylinder head Reinsert the spark plug turning by hand to avoid damaging the threads After the spark plug is seated tighten it using a spark plug wrench so that the washer is compressed A used spark plug should be turned 1 8 of a turn from the seated position A new spark plug should be turned 1 4 a turn from the seated position Replace the ignition cable shoe English 27 MAINTENANCE Inspecting the safety system The Rider is equipped with a safety system that prevents starting or driving under the following c
20. ainst each other and damage the unit 8009 288 6017 020 Cutting unit with side ejection English 39 MAINTENANCE Replacing the break pin Combi 103 The blades are fitted with a break pin to protect the BioClip unit and its drive when colliding with obstacles A domed spring friction washer is fitted to each blade bolt The washer must always be replaced with a new washer if the blade bolt is loosened Otherwise the break pin can break causing the blades to collide Only use original spare parts A set containing a blade break pin and friction washer can be purchased from your dealer 1 Put the cutting unit in the service position see Service position for the cutting unit Placing in the service position 2 Remove the blade 2A by removing the blade bolt with washer and friction washer 2B 3 Remove the remains of the broken break pin 3 4 Make sure the contact surfaces 4 on the blade and the blade mounting are metallic clean 5 Fit one new break pin 5 in the blade mounting 6 Fit the blade 6 make sure it is fitted as illustrated 7 Fit a new friction washer 7 with the concave face turned towards the blade 8 Fit the blade bolt with washer 8 Tightening torque 45 50 Nm 4 5 5 kpm 32 36 Ibft Removal of BioClip plug Combi To change a Combi unit from BioClip function to cutting unit with rear ejection remove the BioClip plug located under the unit with three screws
21. also be adjusted lengthways Move the lever mounted under the frontedge of the seat to the left The seat can then be moved forwards or backwards to the required position 8009 141 Fuelling The engine should be run on 87 octane or higher unleaded petrol gasoline no oil added For more information about methanol and ethanol fuels see Technical Data Do not fill the tank completely leave an expansion area of at least 2 5 cm 1 WARNING Petrol gasoline is highly inflammable Observe care and fill up with fuel outdoors see safety instructions 6004 015 IMPORTANT INFORMATION The air intake grille in the engine cover behind the driver s seat must not be blocked by for example clothing leaves grass or dirt Impaired cooling of the engine Risk of major engine damage 8009 431 16 English DRIVING Before starting e Read the safety instructions and information on the location and function of the controls before starting e Conduct daily maintenance before starting See Maintenance schedule Starting the engine 1 Lift up the cutting unit by pulling the lever backwards to locked position transport posi tion and apply the parking brake 2 Move the throttle control to the middle position 6017 241 3 Ifthe engine is cold move the choke lever backwards to its end position 6017 242 4 Turn the ignition key to the start position 6017 243
22. ave made the adjustment Adjusting the brake The brake is adjusted as follows 1 Release the lock nuts 1 2 Tension the wire with the adjusting screw 2 until all the play in the wire is taken up 3 Tighten the lock nuts 1 4 The brakes should be checked again after the adjustment has been made WARNING Poorly adjusted brakes can result in reduced braking power 24 English 6008 008H 6008 009 6008 010 ET TC iE mE a RL lt s M 6008 239H AMY MAINTENANCE Checking and adjustment of the throttle wire Check that the engine responds to the throttle control and that the correct engine speed is achieved at full throttle If in doubt contact the service workshop If adjustment is necessary adjust the lower wire as follows 1 Release the clamping screw that secures the wire casing and set the throttle control to full throttle 2 Check that the throttle wire is attached to the correct hole in the lower lever see diagram 3 Pull the throttle wire casing to the far left and tighten the clamping screw Checking and adjusting the choke wire If the engine is producing black smoke or is difficult to start then the choke wire upper wire may be incorrectly adjusted If in doubt contact your service workshop If it is necessary to adjust the choke proceed as follows 1 Release the clamping screw that s
23. ctive shoes or protective boots preferably with steel toes Wear approved protective glasses or full face visor during assembly and when operating Never wear loose fitting clothes that can catch in moving parts Use ear protectors to eliminate the risk for impairment of hearing 8 English 8011 292 Personal protective equipment SAFETY INSTRUCTIONS Driving on slopes Driving on slopes is one of the operations where the risk of the driver losing control of the machine or of it overturning is the greatest this can result in serious injury or death All slopes demand extra care If you cannot reverse up a slope or if you feel unsure do not mow it Proceed as follows e Remove obstacles such as stones branches etc e Mow upwards and downwards not sideways 6003 004 Mow upwards and downwards on slopes not sideways e Do not use the machine on ground that slopes more than 15 e Avoid starting or stopping on a slope If the tyres start to slip stop the blades and drive slowly down the slope e Always drive smoothly and slowly on slopes e Do not make any sudden changes in speed or direction e Avoid unnecessary turns on slopes if necessary turn slowly and gradually downwards if possible e Watch out for and avoid driving over furrows holes and bumps It is easier for the machine to overturn on uneven ground Tall grass can hide obstacles e Drive slowly Do not turn the wheel sharply
24. ds Push the height adjustment strut forwards WARNING Wear gloves to protect your hands when working with the blades 3 Loosen the two bolts holding the protective hood and then lift off the hood 4 Useful hint Mark the positions of the blades on the respective pulley using a felt tip pen Loosen the three bolts 1 2 1 turn Press the sides of the belt together to give maximum slack and tighten one of the bolts Replace the belt and tighten as shown see decal on cover Set the blades at 90 to each other and loosen the bolt again The spring ensures the correct belt tension Check the positions of the blades again and adjust if necessary by repositioning the belt on the teeth Tighten the three bolts to 45 Nm 32 Ibft 34 English 6017 154 6017 161 8009 173 MAINTENANCE IMPORTANT INFORMATION The blades on a Combi 103 unit should be set at 90 degrees to each other In all other cases the blades can collide and cause serious damage to the cutting unit 6016 111 5 Fit the protective cover over the belts and replace the parallelism arm 8009 287 Belt change on cutting unit with side ejection and Combi 112 On these cutting units with collision proof blades the blades are driven by one V belt Do as follows to change the V belt 1 Remove the cutting unit 2 Undo the bolt on the lift strut and the two screws on the cover Lift the cover off the cutting unit 3 Loos
25. ecures the wire casing and set the choke control to maxi mum choke 2 Check that the throttle wire is attached to the upper lever see diagram 3 Pull the choke wire casing to the far right and 8009 145 tighten the clamping screw Replacing the fuel filter Replace the pipe fitted fuel filter every 100 running hours once per season or more frequently if it is clogged Replace the filter as follows 1 Fold open the engine cover 2 Move the hose clips away from the filter Use a pair of flat pliers 3 Pull off the filter from the hose ends 4 Press in the new filter on the hose ends If necessary soap solution can be applied on the filter ends to simplify fitting 8009 445 5 Push the hose clips back on the filter English 25 MAINTENANCE Replacing the air filter VARNING Exhaust system is hot Allow to cool down Risk of finger injuries If the engine seems to lack power or runs irregularly the reason may be a clogged air filter It is therefore important to replace the air filter at regular intervals see Maintenance schedule for a correct service interval 1 Remove the air cleaner case from the air cleaner body by pushing down the latches with fingers IMPORTANT INFORMATION Never run the engine with the air cleaner removed Filters should not be oiled They should be assembled dry 8009 447 2 Lift out the paper element and the foam element from the air
26. eels do not bear any weight 5 Adjust the unit s ground pressure by screwing in or out the adjusting screws located behind the front wheels on both sides The ground pressure should be between 12 and 15 kg 26 5 33 Ib 32 English 6017 216 6008 019 MAINTENANCE Checking the cutting unit s parallelism Check the parallelism of the cutting unit as follows 1 Check the air pressure in the tyres 60 kPa 0 6 kp cm 8 5 PSI 2 Place the machine on a level surface 3 Put the lifting lever in the mowing position 4 Measure the distance between the ground and the front and rear edges of the cutting unit hood The cutting unit should slope forwards slightly so that the rear edge is 2 4 mm 1 8 higher than the front edge 6017 217 Adjusting the parallelism of the cutting unit 1 Remove the front hood and right hand fender 2 Undo the nuts on the lift strut 3 Screw out extend the stay to raise the rear edge of the cover Screw in shorten the stay to lower the rear edge of the cover VFR E GR Ei _ 4 Tighten the nuts after adjustment hs 5 On completion of the adjustment the unit s parallelism should be re checked 6 Fit the right hand fender and the front hood 6017 018 English 33 MAINTENANCE Replacing the cutting unit belts Belt change on Combi 103 1 Remove the cutting unit 2 Remove the front bolt from the parallel strut and tip the strut backwar
27. else is in the vicinity of the machine when you start the engine engage the drive or drive off 8010 047 Read the operator s manual before starting the machine e Make sure animals and people maintain a safe distance from the machine e Stop the machine if any one enters the working area e Clear the area of objects such as stones toys wires etc that may become caught in the blades and be thrown out e Look out for the ejector and do not direct it towards anyone e Stop the engine and prevent the engine from being started until you have cleaned the cutting 6003 002 unit or outlet channel Clear the area of objects before mowing e Remember the operator is responsible for danger or accidents e Never carry passengers The machine is only intended to be used by one person e Always look downwards and backwards before and while reversing Keep watch for both large and small obstacles e Slow before cornering e Switch off the blades when you are not mowing 8010 052 Never carry passengers WARNING N This machine can sever hands and feet as well as throw objects Failure to observe the safety instructions can result in serious injuries English SAFETY INSTRUCTIONS Take care when rounding a fixed object so that the blades do not hit it Never run the machine over foreign objects Only use the machine in daylight or in other well lit conditions Keep the machine at a safe distance fr
28. en the spring 4 that tensions the V belt and pry off the belt Simply reverse the procedure to fit the new belt NO li E 5 cum j KA O O 8009 376 English 35 MAINTENANCE Service position for the cutting unit The cutting head can be placed in the service position to provide easy access for cleaning repairs and servicing In the service position the cutting unit is raised and locked in the vertical position Placing in service position 1 Position the machine on flat ground Apply the parking brake A Adjust the cutting unit to the lowest cutting height and lower the cutting unit B o Z M 8009 437 2 Remove the front hood by removing the pin There are complete instructions on using the service position inside the front hood 3 Remove the two support wheels from under the front hood 6017 220 36 English MAINTENANCE 4 Fit the support wheels on either side of the rear of the cutting unit WARNING Wear protective glasses when dismantling the cutting unit The spring which tensions up the belt can go off and cause personal injury 6017 221 5 Disengage the spring for the drive belt tensioning wheel 6017 222 6 Place a foot on the front edge of the cutting unit near the wheel and raise the front edge of the unit to make it easier to remove the lift strut 8009 122 7 Engage the strut in the holder 6017 223 English 37 MAINTENANCE
29. g unit nre 31 Checking and adjusting the cutting unit s ground pressure 1 mittu aitas antama alluda 32 Checking the cutting unit s parallelism 33 Adjusting the parallelism of the cutting unit 33 Replacing the cutting unit belts 34 Service position for the cutting unit 36 Checking the blades ennnuee 39 Replacing the break pin nn 40 Removal of BioClip plug u 40 Lubrication AAMEMMELAMINAEEE AED 41 Checking the engine s oil level 41 Changing the oil AATED 42 Checking the transmission s oil level 43 Lubricating the belt adjuster 43 General lubrication ccccsseeeeeeeeseeeeeees 43 Trouble shooting schedule 44 27 10 e AAE ee UE 45 Winter storage ss timm katja ajatada 45 COVEI re eae pu nu eee 45 GENIC MEET NA i TUUMA 45 Technical data nmenmnmennnun 46 Service journal 00ninmennnnnneennna 47 For service measures other than those described in this manual please contact an authorised dealer that provides parts and service English 1 AN 1 Safety rules for USA AN These instructions are for your safety Read them carefully Safe operation practices for ride on mowers IMPORTANT This cutting
30. he way for safe manoeuvring of the machine e Never allow children to operate the machine e Be particularly careful near corners bushes trees or other objects that block your view Maintenance e Stop the engine Prevent starting by removing the ignition cable from the spark plug or remove the ignition key before making any adjustments or carrying out maintenance e Never fill the fuel tank indoors e Petrol and petrol fumes are poisonous and extremely flammable Be especially careful when handling petrol as carelessness can result in personal injury or fire e Only store fuel in containers approved for the purpose e Never remove the fuel cap and fill the petrol tank ees while the engine is running Never fill the fuel tank indoors e Allow the engine to cool before refuelling Do not smoke Do not fill petrol in the vicinity of sparks or naked flames e Pay attention to the risk of environmental influence when handling oil oil filter fuel and battery Observe the local waste regulations e Electrical shock can cause injury Do not touch wires while the engine is running Do not test the ignition system using your fingers 10 English SAFETY INSTRUCTIONS If leaks arise in the fuel system the engine must not be started until the problem has been resolved Store the machine and fuel in such a way that there is no risk that leaking fuel or fumes can Cause any damage Check the fuel level before each u
31. ll result in the blades cutting the grass at different heights Checking the engine s cooling air intake Clean the air intake grille in the engine cover behind the driver s seat Fold open the engine cover Check that the cooling intake is free from leaves grass and dirt Check the air duct located on the inside of the engine cover ensure it is clean and does not rub against the cooling air intake A blocked cooling intake will interfere with the cooling of the engine which can damage the engine WARNING The cooling air intake rotates when the engine is running Mind your fingers Air intake grille Cooling air intake 8009 370 6008 030 8009 431 8009 474 English 29 MAINTENANCE Fitting the cutting unit WARNING N Wear protective glasses when fitting the cutting unit The collet spring which tensions up the belt can go off and cause personal injury 1 Place the Rider on a flat surface and apply the parking brake Check that the lever for setting the cutting height is in the lowest position Make sure the support wheels are fitted to the cutting unit 1 2 Grasp the handle at the front or hold the frame of the cutting unit 2 and slide the unit underneath the rider mower 6017 159 Make sure that the tongue 3 on the cutting unit engages correctly 8009 438 3 Insert the bolt and secure it with a locking pin WARNING Observe caution to av
32. machine is capable of amputating hands and feet and throwing objects Failure to observe the following safety instructions could result in serious injury or death I General operation 1 Read understand and follow all instructions in the manual and on the machine before starting 2 Only allow responsible adults who are familiar with the instructions to operate the machine 3 Clear the area of objects such as rocks toys wire etc which could be picked up and thrown by the blade 4 Be sure the area is clear of other people before mowing Stop the machine if anyone enters the area 5 Never carry passengers 6 Do not mow in reverse unless absolutely necessary Always look down and behind before and while backing 7 Be aware of the mower discharge direction and do not point it at anyone Do not operate the mower without either the entire grass catcher or the guard in place 8 Slow down before turning 9 Never leave a running machine unattended Always turn off blades set parking brake stop engine and remove keys before dismounting 10 Turn off blades when not mowing 11 Stop engine before removing grass catcher or unclogging chute 12 Mow only in daylight or good artificial light 13 Do not operate the machine while under the influence of alcohol or drugs 14 Watch for traffic when operating near or crossing roadways 15 Use extra care when loading or unloading the machine into a trailer or t
33. manufacturer even for other special tasks for which instructions are delivered with the accessory Use in any other way is considered as contrary to the intended use Compliance with and strict adherence to the conditions of operation service and repair as specified by the manufacturer also constitute essential elements of the intended use This machine should be operated serviced and repaired only by persons who are familiar with its particular characteristics and who are acquainted with the relevant safety procedures Accident prevention regulations all other generally recognised regulations on safety and occupational medicine and all road traffic regulations must be observed at all times Any arbitrary modifications carried out to this machine may relieve the manufacturer of liability for any resulting damage or injury Safe operation practices for Ride On Mowers Before starting cutting operations train different driving operations on an open ground without people nearby until you feel familiar with handling the equipment This is particularly important if you have no or little prior experience of driving a vehicle Data indicates that operators age 60 years and above are involved in a large percentage of riding mower related injuries These operators should evaluate their ability to operate the riding mower safely in order to protect themselves and others from serious injury Never carry children even with the blades off The
34. ntil grease is forced out With daily use lubrication should be conducted twice a week TEEB General lubrication All joints and bearings are lubricated on manufacture with molybdenum sulphide grease Re grease with same type of grease Lubricate the steering and control wires with engine oil The machine should be lubricated regularly and twice a week when used daily Grease from well known brand names petrol companies etc usually maintains a good quality The most important property is that the grease provides good protection against corrosion English 43 TROUBLE SHOOTING SCHEDULE Procedure Problem Engine will not start Starter does not pull round engine Engine does not run smoothly Engine seems to have no power Engine overheats Battery does not charge Machine vibrates Uneven mowing 44 English Fuel tank empty Spark plug defective Spark plug connection defective Dirt in carburettor or fuel pipe Starter does not pull round engine Battery flat Bad contact between cable and battery terminal Lift lever for cutting unit in wrong position Main fuse blown The fuse is placed in front of the battery under the battery cover Ignition lock faulty Gear shift hydrostat pedal not in neutral Hydrostat pedals not in the neutral position Spark plug defective Carburettor incorrectly set Air filter clogged Fuel tank vent blocked Ignition setting defective
35. oid trapping your hand 6017 120 4 Press down the frame and insert the pin Fit the drive belt around the drive wheels of the cutting unit 5 Hook up the height adjustment strut 6017 160 30 English MAINTENANCE 6 Move the support wheels to their parking position 7 Fit the front cover 8009 439 8 Secure the collet spring e ZA ey w q n V 8009 440 Removing the cutting unit WARNING Wear protective glasses when removing the cutting unit The collet spring which tensions up the belt can go off and cause personal injury 1 Carry out points 1 9 to put the cutting unit in the RA service position see Service position for the SNOP cutting unit A 2 Remove the bolt 3 and lift off the cutting unit 6017 021 6017 142 English 31 MAINTENANCE Checking and adjusting the cutting unit s ground pressure To achieve the best cutting results the cutting unit should follow the underlying surface without pressing too hard against it The pressure is adjusted with a screw on each side of the machine 1 Checkthe air pressure in the tyres 60 kPa 0 6 kp cm 8 5 PSI 2 Place the Rider on a flat surface 3 Put the lifting lever in the mowing position 4 Place a set of bathroom scales under the cutting unit s frame front edge so that it rests on the scales If necessary a block can be placed between the frame and scales so that the support wh
36. om holes or other irregularities in the ground Pay attention to other possible risks Never use the machine if you are tired if you have consumed alcohol or if you are taking other drugs or medication that can affect your vision judgment or co ordination Keep an eye on the traffic when working close to a road or when crossing it Never leave the machine unsupervised with the engine running Always stop the blades apply the parking brake stop the engine and remove the keys before leaving the machine Never allow children or other persons not trained in the use of the machine to use or service it Local laws may regulate the age of the user WARNING WARNING Engine exhaust some of its constituents and certain vehicle components contain or emit chemicals considered to cause cancer birth defects or other reproductive impairment The engine emits carbon monoxide which is a colourless poisonous gas Do not use the machine in enclosed spaces 6003 006 Keep children away from the area to be mowed You must use approved personal protective equipment whenever you use the machine Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen Ask your dealer for help in choosing the right equipment Make sure that you have first aid equipment close at hand when using the machine Never use the machine when barefoot Always wear prote
37. onditions The engine should only be possible to start when the cutting unit is in its raised position and the hydrostat pedals are in the neutral position The driver does not need to be seated in the Starter a Works driver s seat Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met Change the AN m conditions and try again Ignition system A Does not work Check that the engine stops if you temporarily move out off the driver s seat while the cutting unit is lowered or the hydrostat pedals are not in the neutral position 28 English MAINTENANCE Main fuse The fuse is located in a loose holder under the battery case cover in front of the battery Type Flat blade U link 15 A Do not use any other type of fuse when replacing A blown fuse indicates that the U link has burnt off Pull the fuse out of the holder when replacing The fuse is used to protect the electrical system If it blows again shortly after replacing then there is a short circuit which must be rectified before the machine is used again Checking the tyre pressure The tyre pressure should be 60 kPa 0 6 kp cm 8 5 PSI all round To improve driving the pressure on the rear tyres can be reduced to 40 kPa 0 4 kp cm 5 6 PSI The maximum tyre pressure is 100 kPa 1 0 kp cm 14 PSI IMPORTANT INFORMATION Different tyre pressures on the front tyres wi
38. r e The serial number of the machine State the type designation and serial number when ordering spare parts The engine number is stated at a bar code decal placed on the left side of the crankcase in front of the starter The bar code states e The serial number of the engine e Code Please state these when ordering spare parts The transmission s serial number is stated on the barcode decal located on the front of the housing on the left hand drive axle e Type designation is stated above the barcode and starts with the letter K e The serial number is stated above the barcode and has the prefix s n e The manufacturers type number is stated under the barcode and has the prefix p n State the type designation and serial number when ordering spare parts English 5 EXPLANATION OF SYMBOLS These symbols are on the machine and in the operator s manual Study them carefully so that you know what they mean LL Read the operator s manual R N a amp AY Reverse Neutral Fast Slow Engine off Battery Choke Fuel M 7 a 00 starr n OO so N Oil level Cutting height Backwards Forwards Ignition AN ks E E O Hydrostatic free wheel Use hearing protection Parking brake Brake Warning 0 Warning amp Never use the machine if persons especially Never carry passengers on the children or animals are in the vicinity machine or eguipment Risk that the Never drive across a machine can
39. r Do not empty the fuel tank and carburettor if stabiliser has been added WARNING Never place an engine with fuel in the tank indoors or in poorly ventilated areas where petrol fumes can come into contact with naked flames sparks or pilot flames in boilers hot water heaters or drying cabinets etc It is highly inflammable and negligent usage can cause severe person injury and material damage Drain off the fuel in an approved container outdoors and well clear of naked flames Never use petrol for cleaning purposes Use degreasing agents and hot water instead To put the machine in order for storage follow these instructions 1 Carefully clean the machine especially under the cutting unit Touch up paint damage to avoid rust 2 Inspect the machine for worn or damaged parts and tighten loose screws and nuts 3 Change the oil and take care of the waste oil 4 Empty the fuel tank Start the engine and run it until the carburettor is emptied of fuel 5 Remove the spark plugs and pour about a tablespoon of engine oil in each cylinder Turn over the engine so that the oil is evenly distributed and then refit the spark plugs 6 Grease all grease nipples joints and axles 7 Remove the battery Clean it charge it and store it in a cool place 8 Store the machine in a clean and dry place and cover it over for extra protection Cover There is a cover to protect your machine during storage or transpo
40. rds and downwards never across Avoid sudden changes in direction Stopping the engine Preferably allow the engine to idle for a minute to obtain normal working temperature before stopping it if it has been working hard Avoid idling the engine for long periods as there is a risk of carbon build up on the spark plugs 1 Lift up the cutting unit by pulling the lever back to the locked position 2 Move the throttle control to the MIN position Turn the ignition key to the STOP 3 When the Rider is at a standstill press down the parking brake and push in the locking button Release lever The release control must be pulled out in order for the Rider to be moved when the engine is shutoff 6007 002 v W 6017 246 a 4 6007 217H English 2 1 MAINTENANCE Maintenance schedule The following mainteneance items should be conducted on the machine For the items not described in these instructions ask an authorised service workshop Maintenance interval in hours Maintenance Page before start Check the engine s oil level Check the engine s cooling air inlet Check the fuel pump s air filter Check the steering wires Check the battery Check the safety system Check screws and nuts Tighten screws and nuts Check for fuel and oil leakage Clean around the silencer Change the engine oil Change the oil filter Check the cutting unit Check the tyre pressures
41. ries supplied by the manufacturer even for other special tasks for which instructions are delivered with the accessory Use in any other way is considered as contrary to the intended use Compliance with and strict adherence to the conditions of operation service and repair as specified by the manufacturer also constitute essential elements of the intended use This machine should be operated serviced and repaired only by persons who are familiar with its particular characteristics and who are acquainted with the relevant safety procedures Accident prevention regulations all other generally recognised regulations on safety and occupational medicine and all road traffic regulations must be observed at all times Any arbitrary modifications carried out to this machine may relieve the manufacturer of liability for any resulting damage or injury 4 English INTRODUCTION Good service Husqvarna products are sold all over the world and only through servicing dealers This is to ensure that you the customer get the best support and service When you need spare parts or advice on service issues warranty terms etc contact This Operator s Manual belongs to Transmission machine with serial number Serial number The serial number can be found on the printed plate attached to the front left hand side under the seat Stated on the plate from the top are e The type designation of the machine e The manufacturers type numbe
42. rsing 7 Speed limiter for driving forwards 10 11 12 13 6017 213 000000000000000000 0000000000000000 l CICL 000000000000000000 6017 239 Parking brake Lock button for parking brake Lever for adjusting seat Fuel tank cap Main lock under seat Lever for disengagement of drive English 13 PRESENTATION Throttle control The throttle control regulates the engine speed and thereby also the rotation speed of the blades To increase or reduce the engine speed the control is moved forwards or backwards Avoid idling the engine for long periods as there is a risk of carbon build up on the spark plugs Choke lever The choke lever is used for cold starting and to give the engine a richer fuel mixture For cold starting the lever is moved backwards to its end position 6017 128 Speed limiter The speed of the machine is steplessly regulated with two pedals Pedal 1 is used to drive forwards and pedal 2 for reversing WARNING A Make sure that branches do not obstruct the pedals when mowing under bushes otherwise you may lose control Parking brake The parking brake is applied as follows 1 Press down the brake pedal 2 Press in the lock button on the steering column 3 Release up the brake pedal while holding the button pressed The lock on the parking brake automatically disconnects when the brake pedal is pressed 6017 011 14 English PRESENTATION
43. rt Contact your dealer for a demonstration Service When ordering spare parts always state the purchase year model type and serial number Always use genuine parts Annual inspection or trimming by an authorised service workshop is a good way of getting the best out of your machine the next season 6017 213 English 45 Dimensions Length without cutting unit Width without cutting unit Height Weight Wheel base Track Tyre size Tyre pressure front amp rear Max gradient Engine Manufacture Power Displacement Fuel Tank volume Oil TECHNICAL DATA Rider 15V2 2020 mm 6 61 ft 880 mm 2 89 ft 1060 mm 3 52 ft 247 260 kg 543 572 Ib including unit 855 mm 2 8 ft Front 715 mm 2 34 ft rear 625 mm 2 05 ft 16 x 6 50 x 8 60 kPa 0 6 kp cm 8 5 PSI 15 Kawasaki model FH 430V 11 2 15 kW h p 431 cm 26 3 cu in Min 87 octane unleaded Max methanol 5 max ethanol 10 max MTBE 15 7 litres 7 4 USat Class SF SG SH or SJ SAE40 SAE30 SAE10W 30 SAE 10W 40 or SAE 5W 20 Oil volume oil filter included 1 5 litres 1 6 USat Oil volume oil filter excluded 1 7 litres 1 8 USat Start Electric starter 12 V Noise emissions and cutting width Measured noise level Guaranteed noise level Cutting width Electrical system Type Battery Spark plug Transmission 100 dB A 100 dB A 970 1120 mm 38 44 12 V negative ground 12 V 24 Ah Champion RCJ8Y electrode gap 0 75 mm
44. ruck ll Slope operation Slopes are a major factor related to loss of control and tip over accidents which can result in severe injury or death All slopes require extra caution If you cannot back up the slope or if you feel uneasy on it do not mow it DO Mow up and down slopes not across Remove obstacles such as rocks tree limbs etc Watch for holes ruts or bumps Uneven terrain could overturn the machine Tall grass can hide obstacles 2 English Use slow speed Choose a low gear so that vou will not have to stop or shift while on the slope Follow the manufacturer s recommendations for wheel weights or counterweights to improve stability Use extra care with grass catchers or other attachments These can change the stability of the machine Keep all movement on the slopes slow and gradual Do not make sudden changes in speed or direction Avoid starting or stopping on a slope If tires lose traction disengage the blades and proceed slowly straight down the slope DO NOT Do not turn on slopes unless necessary and then turn slowly and gradually downhill if possible Do not mow near drop offs ditches or embandments The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch or if an edge caves in Do not mow on wet grass Reduced traction could cause sliding Do not try to stabilize the machine by putting your foot on the ground Do not use grass catcher on steep slopes ll
45. s For this reason do not increase the throttle until the cutting unit has been lowered to the cutting position 6017 130 WARNING Clear the lawn from stones and other object which can be thrown out by the blades Cutting tips e Localise and mark stones and other fixed objects to avoid collision e Start with a high cutting height and reduce down until the required cutting result are obtained e The cutting results are best with a high engine speed fast rotating blades and low driving speed slow moving machine If the grass is not too high and thick the driving speed can be increased without noticeably depreciating the mowing result 6007 212 e The best lawns are achieved if the grass is cut Mowing pattern often Mowing becomes more uniform and the grass cuttings become more evenly distributed over the surface The total time consumption is not greater since it is possible to select a higher driving speed without inferior mowing results e Avoid mowing a wet lawn The mowing results are inferior since the wheels sink down into the soft lawn e Wash down the underside of the cutting unit with water after use Do not use a high pressure jet Put the cutting unit in the service position while doing this e lf you use the mulching function it is important to mow the grass regularly 20 English DRIVING WARNING AN Never drive the machine on ground with a slope of more than 15 Mow slopes upwa
46. se and leave space for the fuel to expand because the heat from the engine and the sun may otherwise cause the fuel to expand and overflow Avoid overfilling If you spill petrol on the machine wipe up the spill and wait until it has evaporated before starting the engine If you spill petrol on your clothing change your clothing Allow the machine to cool before performing any actions in the engine compartment Be especially careful when handling battery acid Acid on the skin can cause serious corrosive injuries In the event of spillage on the skin wash immediately with water Acid in the eyes can cause blindness contact a doctor immediately Take care with battery maintenance Explosive gases form in the battery Never perform maintenance on the battery while smoking or in the vicinity of open flames or sparks This can cause the battery to explode and cause serious injuries Make sure all nuts and bolts are tightened correctly and that the equipment is in good condition Do not modify safety equipment Check regularly to be sure it works properly The machine must not be driven if protective plates protective covers safety switches or other protective devices are not fitted or are defective Do not change the setting of governors and avoid running the engine at excessively high revs If you run too fast you risk damaging the machine components Observe the risk of injury caused by moving or hot parts if the engine
47. ves or other debris build up Clean up oil or fuel spillage Allow machine to cool before storing Stop and inspect the eguipment if you strike an object Repair if necessary before restarting Never make adjustments or repairs with the engine running Grass catcher components are subject to wear damage and deterioration which could expose moving parts or allow objects to be thrown Freguently check components and replace with manufacturer s recommended parts when necessary Mower blades are sharp and can cut Wrap the blade s or wear gloves and use extra caution when servicing them Check brake operation frequently Adjust and service as required D A INIGIELR KEEP HANDS AND FEET AWAY GARDER MAINS ET PIEDS A DISTANCE Danger keep hands and feet away Travel and transport on public roads Check the relevant road traffic regulations before driving the machine on a public road If transporting the machine on another vehicle always use approved securing devices and make sure that the machine is securely held Towing If your machine has a hydrostatic transmission you should only tow it very short distances at low speed if absolutely necessary otherwise the transmission may be damaged Intended use This machine is designed solely for cutting grass on conventional lawns and other cleared and leveled ground without obstacles as rocks stumps etc and in conjunction with accessories supplied by the
48. ving the machine hoods Engine hood The engine is accessible for servicing when the engine hood is lifted up Tilt the seat forward release the rubber strap under the seat and tilt the hood backwards 6008 001 Front hood Release the clip on the front hood and lift off the hood 6017 215 Right hand fender Remove the knob 1 the screws 2 and 3 and lift off the fender 6017 003 Left hand fender Release the screws in the fender 2 and lift off the fender 6017 013 English 23 MAINTENANCE Checking and adjustment of the steering wires The steering is controlled by means of wires These can in time become slack which implies that the adjustment of the steering becomes altered Check and adjust the steering as follows 1 Dismantle the frame plate by releasing the screws two on each side 2 Check the tension of the steering wires by pushing them together as shown in the diagram It should be possible to push them together so that the distance between them is half as much without using unnecessary force 3 If necessary the wires can be adjusted by tightening the adjuster nuts on each side of the steering collar Do not tension the wires too much they should only be tightened against the steering collar Support the wire so it does not twist If you tension only one side the steering wheel s centre position may change Check the wire tension as set out in point 2 after you h
49. y may fall off and be seriously injured or interfere with safe machine operation English 3 INTRODUCTION Dear customer Thank you for choosing a Husqvarna Rider Husqvarna Riders are built to a unique design with a frontmounted cutting unit and a patented rear wheel steering system Riders are designed for maximum efficiency even in small or confined areas Collected controls and a hydrostatic transmission controlled by pedals also contribute to the machine s performance We hope you will find this operator s manual very useful By following its instructions on operation service maintenance etc you will significantly extend the life of the machine and even its second hand value When you sell your Rider make sure you pass on the operator s manual to the new owner Travel and transport on public roads Check the relevant road traffic regulations before driving the machine on a public road If transporting the machine on another vehicle always use approved securing devices and make sure that the machine is securely held Towing Your machine is equipped with a hydrostatic transmission and if necessary you should only tow the machine over short distances and at a low speed otherwise there is a risk of damaging the transmission Intended use This machine is designed solely for cutting grass on conventional lawns and other cleared and leveled ground without obstacles as rocks stumps etc and in conjunction with accesso
Download Pdf Manuals
Related Search