Husqvarna I0807213 User's Manual
Contents
1. NOTE If your tractor hitch has ridges that prevent the sleeve hitch assembly from resting flat place the spacer plate underneath the sleeve hitch assembly SLEEVE HITCH LIFT LEVER FRAME ASSEMBLY ASSEMBLY HEX BOLT 5 8 x 1 3 4 gt i SPACER PLATE 5 SEE NOTE a 5 8 NYLOCK NUT FIGURE 4 8 Assemble the two 5 8 jam nuts halfway onto the two 5 8 x 2 hex bolts Screw the bolts into the nuts that are welded to the Sleeve Hitch Lift Assembly Tighten the jam nuts against the welded nuts See figure 5 9 Assemble the lifting link to the Sleeve Hitch Lift Assembly using a 5 8 x 1 3 4 hex bolt and a 5 8 nylock nut Use the bottom hole in the lifting link gives the lowest implement depth setting Tighten the nut only until snug Do not squeeze the welded arms together See figure 5 LIFTING LINK n 5 8 NYLOCK NUT 5 8 x 1 3 4 HEX BOLT 5 8 JAM NUT 5 8 x 2 HEX BOLT FIGURE 5 10 Attach the Sleeve Hitch Lift Assembly to the Sleeve Hitch Frame Assembly using three 5 8 x 1 3 4 clevis pins and 3 32 hair cotter pins as shown in figure 6 11 Install the hitch pin in the sleeve hitch and secure it with the 5 32 hair cotter pin See figure 6 5 32 HAIR COTTER PIN 3 3 32 HAIR COTTER PINS 3 CLEVIS PINS FIGURE 6 OPERATION 1 Move the lift lever backward to lower the sleeve hitch 2 Attach an implement using the sleeve hitch pin Tighten the 5 8 x2. 2 stabilizer bolts against the implement hitch and then tighten the jam nuts See figure 5 on page 4 IMPORTANT Some implements may require that the stabilizer bolts not be tightened Refer to your implement owner s manual 3 The sleeve hitch is assembled in the lowest position by the assembly instructions If the implement attached to the sleeve hitch is not level front to back during operation a Move the hex bolt in the lifting link to a hole 3 holes available that gives better levelling b For closer adjustment move the hex bolt assembled in figure 1 to a position in the three position slot that gives better levelling 4 Totow an implement that has a tow hitch simply remove three clevis pins and then remove the Sleeve Hitch Lift Assembly from the Sleeve Hitch Frame Assembly 5 To remove the entire Sleeve Hitch attachment remove the 5 8 x 1 3 4 hex bolt and 5 8 nylock nut which fasten the bottom of the sleeve hitch to the tractor hitch then lift the attachment off the tractor MAINTENANCE 1 Clean off after each use 2 Oil pivot points as needed 3 Store in a dry location REPAIR PARTS FOR MODEL 45 03021 SLEEVE HITCH Ret PartNo ty Description Ref PartNo Qty Description oo oNnNOVPwDPD 65409 25715 25714 43350 HA21362 65404 64625 24732 47947 712 0242 HA3980 47951 712 0261 47950 NNO0NN bp ana Sleeve Hitch Frame Pivot Bracket Left Pivot Bracket Right Bolt C
3. 3 8 x 1 Clevis Pin Jam Nut 5 8 Nylock Nut 5 8 Nylock Nut 5 16 KEY QTY DESCRIPTION Nylock Nut 3 8 Hex Nut 3 8 Lock Washer 3 8 Flat Washer 3 8 Spacer Spacer Plate 3 32 Hair Cotter Pin 5 32 Hair Cotter Pin ee ovozzecz B NOTE Bolt C Lock Washer L and Nut K will not be used unless the mounting holes in the tractor do not already contain bolts and nuts CARTON CONTENTS IFYOUR TRACTOR LOOKS LIKE FIGURE 2A 2 Install two 3 8 x 1 1 4 hex bolts in the left side of the tractor as shown Attach the left L H Mounting Bracket pin at top facing in to the bolts using two 3 8 lock washers and 3 8 hex nuts Repeat on the right side See figure 2A qu A SS Sleeve Hitch Frame Assembly Mounting Bracket R H Mounting Bracket L H Lifting Link Plate Hitch Pin Lift Lever Assembly with R H Pivot Bracket L H Pivot Bracket Sleeve Hitch Lift Assembly FIGURE 2A D NO e ON gt IF YOUR TRACTOR LOOKS LIKE FIGURE 2B 3 Remove the nuts from the two bolts in each side of the tractor leaving the bolts in place See figure 2B ASSEMBLY 4 Attach the left LH and right RH Mounting Brackets to the bolts using the original nuts and two 3 8 flat washers TOOLS REQUIRED FOR ASSEMBLY The brackets should angle outward with the weld pins 1 1 2 Wrench or Adjustable Wrench at the top of the brackets facing inward See figure 2
4. B 2 9 16 Wrenches or Adjustable Wrenches NOTE If no bolt and nut are present in a hole use a 3 8 x 1 15 16 Wrenches or Adjustable Wrenches 1 1 4 hex bolt 3 8 lock washer and 3 8 hex nut to attach the Mounting Bracket to the hole 1 Assemble a 5 16 x 1 hex bolt a spacer and a 5 16 nylock nut to the three position slot in the R H pivot bracket on the left lever assembly Use the position ET closest to the bend in the bracket lowest implement RIGHT MOUNTING depth setting See figure 1 ARCEM o gt REMOVE NUTS v SFACER FROM BOLTS y PIVOT 56 X 1 Wr me 15 16 NYLOCK 3 8 FLAT WASHER 57 oP _ TOP HOLE ONLY NASA LEFT MOUNTING BRACKET 3 8 LOCK WASHER If new bolt and nut are needed ORIGINAL NUT FIGURE 1 FIGURE 2B 5 Place the L H Pivot Bracket onto the end of the Lift Lever Assembly the R H Pivot Bracket comes already installed on the assembly See figure 3 6 Attach the R H and L H Pivot Brackets to the Sleeve Hitch Frame Assembly using four 3 8 x 1 carriage bolts and 3 8 nylock nuts See figure 3 L H PIVOT BRACKET R H PIVOT BRACKET LIFT LEVER ASSEMBLY 3 8 16 x 1 CARRIAGE BOLT 3 8 NYLOCK NUT SLEEVE HITCH FRAME FIGURE 3 7 Hook the Sleeve Hitch Frame Assembly onto the weld pins in the mounting brackets Attach the bottom of the Assembly to the tractor hitch using a 5 8 x 1 3 4 hex bolt and a 5 8 nylock nut See figure 4
5. Illustrated 2008 01 4 Husqvarna 531 30 70 05 Sleeve Hitch 23 inch tire 45 03021 Repair Parts Manual Agriefal OWNERS MANUAL Model No 45 03021 SLEEVE HITCH CAUTION Safet Read Rules for ied Gafe O e Assembly ate Operation Operation and Instructions e Maintenance Carefully e Parts SpeedeP ai T the fastest way to purchase parts Www speedepart com PRINTED IN USA FORM NO 49949 10 05 SAFETY RULES 1 Readthis owners manual and your vehicle and implement owners manuals before using this hitch Before lowering and operating the implement be sure no one is near the area of operation 2 Do not allow children to operate vehicle or sleeve Lower the sleeve hitch and implement when leaving hitch vehicle unattended 3 Donot allow adults to operate the vehicle or sleeve hitch Vehicle braking and stability may be affected Drive slowly without proper instructions when sleeve hitch and implement are in raised position 4 Do not allow anyone to ride on sleeve hitch Stay off of steep slopes 5 Always place sleeve hitch in lowered position when Keep all nuts and bolts tight and be sure the equipment HARDWARE PACKAGE SHOWN FULL SIZE KEY QTY zeosmooss 8 attaching an implement is in safe operating condition DESCRIPTION Hex Bolt 5 8 x 2 Hex Bolt 5 8 x 1 3 4 Hex Bolt 3 8 x 1 1 4 Hex Bolt 5 16 x 1 Carriage Bolt
6. arriage 3 8 16 x 1 Hex Lock Nut 3 8 16 Sleeve Hitch Lift Assembly Lift Lever Assembly Lifting Link Plate Bolt Hex 5 8 11 x 2 Hex Jam Nut 5 8 11 Clevis Pin 5 8 x 1 3 4 Bolt Hex 5 8 11 x 1 3 4 Nylock Nut 5 8 11 Pin Sleeve Hitch 15 16 17 18 19 20 21 22 23 24 25 26 27 AA ANa AH AH SH SH SH SH 3H Pin Hair Cotter 3 32 Grip Plastic Bolt 5 16 18 x 1 Spacer Nylock Nut 5 16 Mounting Bracket Right Mounting Bracket Left Pin Hair Cotter 5 32 Spacer Plate Flat Washer Bolt Hex 3 8 16 x 1 1 4 Lock Washer 3 8 Hex Nut 3 8 16 Owner s Manual NOTES SpeedEP al T the fastest way to purchase parts www speedepart com REPAIR PARTS Agri Fab Inc 809 South Hamilton Sullivan IL 61951 217 728 8388 O 2004 Agri Fab Inc www agri fab com
Download Pdf Manuals
Related Search