Husqvarna 115 145727 User's Manual
Contents
1. 24 25 26 2T 28 29 30 539 976938 539 100472 539 990209 539 990188 521 996501 522 923202 539 976941 525 497001 539 108082 539 108081 539 108088 539 108083 539 108085 539 108086 539 108163 QTY DESCRIPTION ie 18 x 2 RHSNB 5 16 18 x 1 HCS 5 1 18 x 1 WASHER 16 SAE FLAT NUT 3 8 16 HEX FLG NYLOC BRACKET WEIGHT HCS 3 8 16 x 1 CHUTE UPPER INDICATOR BAG DUMP SCREW 110 14 x LATCH HOOD SCREW 10 24 11 s SPACER SPLIT NUT 10 24 ACORN DECAL CATCHER NOTE ALL FASTENERS ARE GRADE 5 UNLESS OTHERWISE SPECIFIED 15 SECTION 1 LIMITED WARRANTY HUSQVARNA PRODUCT REGISTRATION INFORMATION amp WARRANTY STATEMENT Husqvarna products can be registered online at www usa husqvarna com quickly and easily regardless of their model year Click the Support tab then click on the Online Product Registration link and fill out the electronic form and submit Ask about Husqvarna s extended service plan Husqvarna Professional Products Inc Husqvarna warrants the original purchaser the Husqvarna branded product to which this warranty apply the Product that the Product shall be free from defects in material and workmanship from the date of purchase for the period of the applicable Warranty Schedule of the Product as set forth below Additional limi2. Turn off blades when not mowing Stop engine before removing grass catcher or unclogging chute Mow only in daylight or good artificial light Do not operate the machine while under the influence of alcohol or drugs Watch out for traffic when operating near or crossing roadways Use extra care when loading and unloading the machine onto a trailer or truck Data indicates that operators age 60 years and above are involved in a large percentage of riding mower related injuries These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury DO NOT operate mower with grass catcher unless the front weights are installed Keep machine free of grass leaves or other debris buildup which can touch hot exhaust engine parts and burn Do not allow the mower deck to plow leaves or other debris which can cause buildup to occur Clean any oil or fuel spillage before operating or storing the machine Allow machine to cool before storage SLOPE OPERATION Slopes are a major factor related to loss of control and tip over accidents which can result in severe injury or death All slopes require extra caution If you cannot back up the slope or if you feel uneasy on it do not mow it DO Mow up and down slopes 10 Max not across e Remove obstacles such as rocks tree limbs etc e Watch for holes ruts or bumps Uneven terrain could overturn th
3. containers on support frame overlapping containers at center tube Note One container should always overlap the other container at the center tube Close cover and lock latch handle over support tubes Latch Handle Sy A Support i Frame WARNING DO NOT operate mower unless container is properly installed Container is subject to wear and deterioration check containers frequently replace when cracked or damaged Use only a recommended replacement container 5 LOWER CHUTE INSTALLATION 1 Raise and hold deflector shield in upright position 2 Fitlower chute as shown and hook rear latch to mower deck 3 Align the bracket slot on lower chute with the deflector bracket tab on the mower deck Slide chute down over tab 4 With the lower chute in proper position hold the chute securely while hooking the front latch to the mower deck NOTE While hooking the latches the deflector shield may try to push the chute away from the mower deck opening It is important to hold the chute in position while hooking the latches to the mower deck Deflector Shield Deflector Bracket Tab Rear Latch Attach Rear Latch here ASSEMBLY 6 P F CHUTE INSTALLATION 7 CHUTE HOOD INSTALLATION Push upper chute through the gasketed opening in the cover assembly 2 Rotate chute so the chute opening is downwards toward the container bags NOTE Depending on model it may be necessary to drill a
4. grass catcher partially installed Disengage blades and stop engine before leaving mower seat to empty containers unclogging chutes etc Close cover before starting Disengage mower blades when crossing driveways or gravel surfaces and other areas where thrown objects could be a hazard DO NOT attempt to vacuum up cans or other potentially hazardous projectiles CAUTION Grass catcher components are subject to wear damage and deterioration which could expose moving parts or allow objects to be thrown Frequently check components and replace with manufacturer s recommended parts when necessary SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE ON MOWERS Keep machine free of grass leaves or debris buildup Clean oil or fuel spillage Allow machine to cool before storing Stop and inspect the equipment if you strike an object Repair if necessary before restarting Never make adjustments or repairs with the engine running Grass catcher components are subject to wear damage and deterioration which could expose moving parts or allow objects to be thrown Frequently check components and replace with manufacturer s recommended parts when necessary Mower blades are sharp and can cut Wrap the blade s or wear gloves and use extra caution when servicing them Check brake operation frequently Adjust and service as shown in the Operator s Manual A WARNING Battery posts terminals
5. hole to move the upper chute latch nut 1 Slide upper chute onto lower chute lining up notches and channels If latch on lower chute and latch nut on upper chute are aligned skip to Step 3 2 If upper chute latch nut is not aligned to the lower chute bungee drill a 1 4 hole 27 from the lower edge of the upper chute and in alignment with the lower chute latch Move latch nut and hardware to new hole placement 7 3 Stretch bungee latch up onto acorn nut on chute to secure Rotate upper chute to point downwards towards bags if necessary Hood Inlet 8 LEVELING MOWER DECK Be sure deck is properly leveled for best mower performance See your mower operator s manual for instructions Before continuing to Step 7 locate the seal fastening kit packed separately and install the top cover grommet 10 OPERATION IMPROVED BAGGING TIPS Follow the mower operation instructions in the mower Operator s manual When using the grass catcher on a lawn where grass and leaf bagging equipment has not been used thatch and debris that has accumulated for long periods of time will be picked up The amount collected and the total time of operation may be greater than experienced with regular use of the grass catcher e Always run throttle at full speed when bagging e Select a speed low enough to give good mower cutting performance good quality cut and good bagging performance NOTE It
6. tighten nuts at this time Support Mount Hanger Bracket 3 Secure rear end of support straps to outside of hanger assembly Set reinforcement plates to the outside of the tank brackets and fasten front end of support strap to tank bracket and reinforcement plate with round head bolt Secure front end of reinforcement plate to tank bracket with hex bolt Fully secure all mounting hardware See illustration NOTE Depending on model rear guard hole may need to be drilled out to if kit hardware is too large Hex Bolt Placement Round Head Bolt Placement Reinforcement Plate Support Straps MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY For ease of assembly you may wish assistance from another person for mounting the cover assembly to mower 1 Position cover assembly on the ground behind the mower 2 Lift and rotate cover to align the frame bracket with the hanger and slide the cover down until secure Cover Assembly Frame Bracket Hanger 3 INSTALLING SPACER PLUG Remove plastic end cap from the center bag support arm Fully insert spacer plugs into the ends of the support tube It may be necessary to tap the spacer into place with a hammer or mallet Replace the plastic end cap back over the spacer The additional extension will hold the hood more securely when latched end cap replace cap ASSEMBLY 4 CONTAINER INSTALLATION 1 Install
7. ED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT HUSQVARNA RESERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NOTICE AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY MANUFACTURED PRODUCTS Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary by state SECTION 5 CUSTOMER RESPONSIBILITIES The product must exhibit reasonable care maintenance operation storage and general upkeep as written in the maintenance section of the Owner s Operator s manual Should an operational problem or failure occur the product should not be used Failure caused by continued use is not covered by warranty Product should be delivered at owners expense as is to an authorized Husqvarna Servicing Retailer for evaluation Proof of purchase as explained in section 6 rests solely with the customer SECTION 6 PROCEDURE TO OBTAIN WARRANT
8. N COVER 13 532 400226 2 _ STRIP REINFORCEMENT pcc LATCH HANDLE COVER SCREW 10 24 x 5 8 a SPRING COVER LH PN SPRING COVER RH i cundo ae SPACER COVER 19 539 108086 9 SPRING RETAINER CAP TUBING END DESCRIPTION BAGGER FRAME PIN HINGE CONTAINER SOFT BAG WASHER 10 FLAT NUT 10 24 HEX NYLOC HMS 10 24 94 SPACER PLUG NUT 10 24 ACORN NOTE ALL FASTENERS GRADE 5 UNLESS OTHERWISE SPECIFIED 13 PARTS 5 N gt 8 14 ITEM PART NO i o NOONA oO gt 539 111006 539 108194 539 976952 539 108084 539 108089 539 113232 539 109552 522 854402 522 854502 922 854602 522 854702 539 990316 539 112899 523 112802 939 108271 D BR NNA H H H WH 0 Oo MN QTY CHUTE LOWER LATCH ASSM CHUTE SCREW 10 24 x 5 s WASHER 16 GA NUT 10 24 WELD WEIGHT PLATE WASHER LOCK STRAP SUPPORT STRAP SUPPORT LT MOUNT COLLECTION BRACKET COLLECTION RHSNB 5 16 18 94 NUT ie 18 FLG NYLOC PLATE HCS 3 8 16 3 PARTS DESCRIPTION ITEM PART NO 16 17 18 19 20 21 22 23
9. Operator and Parts Manual GRASS CAT CHER 42 966004001 CONTENTS SAFETY EE 4 GENERAL OPERATION tenir rn 4 SLOPE OPERATION to ripe tenus 4 CHILDREN eee 5 SERVI G Es cT 5 CONTAINER CONTENT 7 ASSEMBLY en 8 CONGRATULATIONS on your purchase of a new Grass Catcher It has been designed engineered and manufactured to give you the best possible dependability and performance Should you experience any problem you cannot easily remedy contact the nearest authorized service center department They have competent well trained technicians and the proper tools for service and repairs Read and retain this manual The instructions will enable you to assemble and maintain your collection system properly Always observe the SAFETY RULES yz e T 11 IMPROVED BAGGING TIPS 11 GENERAL RECOMMENDATIONS 11 STORAGE NS ne 11 PARTS PT 12 KNOW YOUR GRASS CATCHER READ THIS OPERATION MANUAL AND SAFETY RULES BEFORE ASSEMBLING OR OPERATING YOUR GRASS CATCHER Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the assembly Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to prevent injury to yourself and others Save this manual for future reference WARNING The operation of any mower can result in foreign objects thrown into th
10. Y CONSIDERATION It is the Owner s and Retailer s responsibility to make certain that the Warranty Registration Card is properly filled out and mailed to Husqvarna This card should be mailed within ten 10 days from the date of purchase in order to confirm the warranty and to facilitate post sale service Proof of purchase must be presented to the authorized Husqvarna retailer in order to obtain warranty service This proof must include date purchased model number serial number and complete name and address of the selling retailer To obtain the benefit of this warranty the product believed to be defective must be delivered to an authorized Husqvarna retailer in a timely manner no later than thirty 30 days from date of the operational problem or failure The product must be delivered at the owner s expense Downtime pick up and delivery charges are not covered by this warranty An authorized Husqvarna retailer can be located by calling 1 800 HUSKY 62 or visiting www husqvarna com Subject to change without notice HUSQVARNA 7349 Statesville Road Charlotte NC 28269 IR Part Number 525 88 56 01 P N 115 145727 IR 05 20 09
11. and related accessories contain lead and lead compounds chemicals know to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling WARNING DO NOT tow any trailers etc with this mower They may jackknife or over turn causing damage to the mower and possibly serious injury to the operator UNPACKING INSTRUCTIONS e Remove all parts and packing materials from carton e Check carton contents against list Be sure all parts are there TOOLS REQUIRED Yo Wrench 2 9e Wrench 2 The Wrench 2 Ft Lbs Torque Wrench Drill 14 and ie Drill Bits 9 16 Socket and Ratchet Standard Screwdriver PARTS IDENTIFICATION COVER ASSEMBLY BAG CONTAINERS seated on the mower in the operator s position CONTAINER CONTENTS 2 Soft bag containers 1 Bag of Hardware 1 Upper Chute 1 Lower Chute 1 Cover Assembly 1 Mounting Hardware 1 Weight UPPER CHUTE CAUTION BEFORE ASSEMBLING GRASS CATCHER TO MOWER Set parking brake Place motion control levers in NEUTRAL position Turn ignition key OFF and remove key Make sure the blades and all moving parts have completely stopped Disconnect spark plug and place wire where it cannot come in contact with plug ASSEMBLY 1 INSTALL PLATE AND HANGER 1 Using hardware provided in kit attach support mount to unit 2 Attach hanger bracket to support mount Do not fully
12. cher containers are full a Disengage blades place motion control levers in neutral position Unlatch and raise cover Slide out containers and dispose of clippings Replace containers close cover and latch b Unlatch chutes and check for clogging Remove all debris in chute Reassemble and latch chutes GENERAL RECOMMENDATIONS Always observe safety rules when performing any maintenance e Before each use check for loose fasteners e Clean unit thoroughly after each use BLADE CARE For best results mower blades must be kept sharp Replace bent or damaged blades See BLADE CARE instructions in your mower operator s manual STORAGE When grass catcher is to be stored for a period of time clean it thoroughly remove all dirt grass leaves etc Store in a clean dry place CAUTION Do not leave grass in bagger containers Empty containers after each use and before storing Failure to do so may result in spontaneous combustion which could develop into a fire 11 PARTS 12 ITEM PART NO 1 NO 0 539 111139 532 127533 532 155042 532 130895 539 976952 532 132796 582 132983 532 133235 539 108096 539 108097 QTY Lon PARTS DESCRIPTION ITEM PARTNO QTY COVER ASSM COMPLETE 11 532 179746 1 INCLUDES ITEMS 2 4 gt ne dore SCREE
13. down for small children e Never carry children They may fall off and be seriously injured or interfere with safe machine operation e Use extra care when approaching blind corners shrubs trees or other objects that may obscure vision SERVICE e operation of any mower can result in foreign objects thrown into the eyes which can result in severe eye damage Always wear safety glasses or eye shields while operating your mower or performing any adjustments or repairs We recommend a wide vision safety mask over spectacles or standard safety glasses Use extra care in handling gasoline and other fuels They are flammable and vapors are explosive J Use only an approved container Never remove gas cap or add fuel with the engine running A Allow engine to cool before refueling smoke Never refuel the machine indoors Never store the machine or fuel container inside where there is an open flame such as a water heater e Never run a machine inside a closed area Keep nuts and bolts especially blade attachment bolts tight and keep equipment in good condition e Never tamper with safety devices Check there proper operation regularly CAUTION In order to prevent accidental starting when setting up transporting adjusting or making repairs always disconnect spark plug wire and place wire where it cannot contact spark plug CAUTION DO NOT operate mower with
14. e eyes which can result in severe eye damage ALWAYS wear safety glasses or eye shields before starting your mower and while mowing We recommend a wide vision safety mask for over the spectacles or standard safety glasses SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE ON MOWERS DANGER THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH GENERAL OPERATION Read understand and follow all instructions in the manual and on the machine before starting Only allow responsible adults who are familiar with the instructions to operate the machine Clear the area of objects such as rocks stones toys wire etc which could be picked up and thrown by the blades Be sure the area is clear of all people and pets before mowing Stop the machine if anyone enters the area Never carry passengers or children even with blades off Do not mow in reverse unless absolutely necessary Always look down and behind before and while backing Be aware of the mower discharge direction and do not direct it towards anyone Do not operate the mower without either the entire grass catcher or the guard in place Slow down before turning Never leave the machine unattended when the engine is running Always turn off the blades set the parking brake stop the engine and remove the key before leaving the machine
15. e machine Tall grass can hide obstacles e Use slow speed Choose a low speed so that you will not have to stop while on the slope e Use extra care with grass catchers or other attachments These can change the stability of the machine e Keep all movement on the slopes slow and gradual Do not make sudden changes in speed or direction e Avoid starting or stopping on a slope If tires lose traction disengage the blades and proceed slowly straight down the slope DO NOT e Do turn on slopes unless necessary and then turn slowly and gradually downhill if possible Do not mow near drop off ditches or embankments The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch or if an edge caves in e not mow on wet grass Reduced traction could cause sliding e Do not try to stabilize the machine by putting your foot on the ground SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE ON MOWERS CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children Children are often attracted to the machine and the mowing activity Never assume that children will remain where you last saw them e NEVER allow children to operate the machine Keep children out of the mowing area and under the watchful care of another responsible adult e alert and turn off the machine if children enter the area e Before and when backing look behind and
16. ial due to ultraviolet light 3 Engine and drive systems not manufactured by Husqvarna these items are covered by the respective manufacturer s warranty as provided in writing with the product information supplied at the time of purchase all claims must be sent to the appropriate manufacturer 4 Lawn and garden attachments that are covered by a third party which gives a warranty all claims for warranty should be sent to the manufacturer 5 Commercial or consumer mowing decks with sand abrasion damage 6 Emission Control System components necessary to comply with CARB TIER Il and EPA regulations which are manufactured by third party engine manufacturer SECTION 4 EXCEPTIONS AND LIMITATIONS This warranty shall be inapplicable to defects resulting from the following 1 Accident abuse misuse negligence and neglect including stale fuel dirt abrasives moisture rust corrosion or any adverse reaction due to incorrect storage or use habits 2 Failure to operate or maintain the unit in accordance with the Owner s Operator s manual or instruction sheet furnished by Husqvarna 3 Alterations or modifications that change the intended use of the product or affects the product s performance operation safety or durability or causes the product to fail to comply with any applicable laws or 4 Additional damage to parts or components due to continued use occurring after any of the above REPAIR OR REPLACEMENT AS PROVID
17. may be necessary to overlap width of cut to suit your conditions e If grass is extremely tall it should be mowed twice The first time relatively high the second time to desired height e Use left hand side of mower for trimming e Plastic trash bags 3 0 mil 30 gallon can be inserted inside grass catcher containers for ease of debris disposal To remove the plastic trash bags when full a Disengage blades shift into neutral engage the parking brake and stop the engine Unlatch and raise cover c Remove one container at a time by grasping container handles and pulling toward the rear off of the tube rails d With the container resting on the ground close and secure the top of the plastic lawn bag e Tip the container on its side and slide the filled bag from the container f Install a new plastic lawn bag with the edges of the bag draped over upper lip of the container g Repeat for other container Reinstall containers making sure right container overlaps left container at center supports i Close cover and secure latches over center support tubes e Avoid cutting wet grass mowing in the morning while the dew is still heavy Grass clippings collected under these conditions tend to be sticky and adhere to the walls of the flow path causing clogging e grass catcher fails to pick up cut grass or leaves it is an indication that clogging has occurred in the system or that the grass cat
18. n Riders t 3 Years or 600 Hours 1 Year or 600 Hours 90 Days iZ LZ BZ Series Zero Turn Riders f Applies to units factory equipped with Roll Over Protection System 5 Years or 1 500 Hours 5 Years or 1 500 Hours 90 Days Commercial Walk Mowers f includes 21 amp wide area 3 Years 3 Years 90 Days Commercial Turf Specialty Equipment T 1 Year 1 Year 1 Year Zero Turn amp Commercial Turf Specialty Attachments 2 Years 1 Year 90 Days Power Cutters Lifetime Ignition Warranty Parts Only 1 Year 1 Year C720 only 90 Days Automatic Mower 1 Year Battery Warranty 2 Years 90 Days 90 Days Snow Throwers t 2 Years 90 Days 90 Days 2Y Pressure Washers 2 Years Excludes 5525PW NA Generators Husqvarna s warranty does not cover Engine amp Generator Parts which warrantied by responsible manufacturer t 29 Only 2 Years 1965GN only N A 2 Year Parts only Grass Catchers amp Bumpers Purchased with New Units Spreaders Same Warranty As Unit When Purchased with Unit 1 Year Parts amp Accessories Purchased Separately 30 days Husqvarna Utility Vehicles Engines transmissions shall be warrantied through Husqvarna 2 Year or 2 000 Hour Powertrain amp 1 Year or 1 000 Hour Body Warranty HUV Batteries 4210E Versions 4 Year Pro rated Husqvarna Safety Apparel 90 day Batteries Consumer Products where applicable 1 year N A Replacement Parts Accessories including Bar
19. s and Chains Tools and Display Items Emission Control System Components necessary to comply with CARB TIER Il and EPA Regulations Excludes components which are part of engine systems manufactured by third part engine manufacturers for which the purchaser has received a separate warranty with product at time of purchase 30 Day Warranty Part Number 525 88 56 01 Refer to Section 3 for items not covered by this warranty All consumer product use must have been limited to the owners residence Warranted for noncommercial nonprofessional noninstitutional and nonincome producing use HUV 2 Year or 2 000 Hour Powertrain The engine assembly unitized transaxle assembly gasoline vehicle motor and main frame assembly are warranted with respect to parts and labor against defects in material and workmanship or a period of two years or 2000 hours of operation whichever first occurs from the date of purchase amp 1 Year or 1 000 Hour Body Warranty All remaining components of the vehicle not specified otherwise and all other original equipment options and accessories supplied by Husqvarna are warranted with respect to parts and labor against defects in material and workmanship for a period of one year or 1000 hours of operation whichever first occurs from the date of purchase HUV s Gas amp Diesel Powered Battery 0 6 months free replacement and 7 12 months prorated HUV s Electric Powered 4 year or 16 000 Energy Uni
20. t Limited Warranty Period Husqvarna safety apparel warranty is from the date of the customer s original purchase for defects in material and workmanship Normal wear tear or abuse is not covered under warranty All care and maintenance instructions must be followed as stated by the manufacturer on the care label The fit of the protective apparel boot is not covered under warranty 1 Year prorated limited warranty with 100 replacement during the first 6 months Lifetime Warranty Parts and Labor All tiller tines and trimmer shafts against breakage Proof of purchase required Lifetime Warranty PARTS ONLY after initial warranty expiration Ignition coils and modules on handheld product Proof of purchase required SECTION 2 HUSQVARNA S OBLIGATIONS UNDER THE WARRANTY Husqvarna will repair or replace defective components without charge for parts or labor if a component fails because of a defect in material or workmanship during the warranty period SECTION 3 ITEMS NOT COVERED BY THIS WARRANTY The following items are not covered by this warranty 1 Normal customer maintenance items which become worn through normal regular use including but not limited to belts blades blade adapters bulbs clutches clutch drums filters fuel line fuel filters air filters oil filters sprockets guide bars lubricants rewind springs saw chain spark plugs starter ropes and tiller tines 2 Natural discoloration of mater
21. tations are described in Section 2 through 6 inclusive CONSUMER COMMERCIAL RENTAL PRODUCT CATEGORY WARRANTY SCHEDULE PROFESIONAL WARRANTY WARRANTY SCHEDULE SCHEDULE Reconditioned Products Reconditioned chainsaws trimmers brushcutters clearing saws handheld blowers 90 Days N A N A backpack blowers hedge trimmers and electrical products Chain Saws Lifetime Ignition Warranty Parts Only One Year Conditional Crankshaft Warranty for Commercial Professional use when operated with 2 Years 90 Days 90 Days Husqvarna XP 2 cycle oil Parts amp Labor 100 Series Trimmers Stick Edgers Hedge Trimmers 2 Years 1 90 Days Lifetime Ignition Warranty Parts Only Lifetime Shaft Warranty 200 amp 300 Series Trimmers Brushcutters Clearing Saws Stick Edgers Hovering Trimmers amp Hedge Trimmers 2 Years ivar 90 Days Lifetime Ignition Warranty Parts Only and Lifetime Shaft Warranty apply to these products excludes Hovering Trimmers Blowers Lifetime Ignition Warranty Parts Only 2 Years 2 Years 90 Days Pole Pruners Pole Saws Pole Hedge Trimmers Lifetime Ignition Warranty Parts Only 1 Year 1 Year 90 Days Residential Walk Behind Mowers Tillers LE389 Edger t 2 Years N A N A LE475 Edger 1 2 Years 90 Days 90 Days LT LTH LS XLS GLS YT YTH GT GTH 16H Pro15 155 ProFlex Series Lawn amp Garden Riders and Residential Zero Turn Mowers t 2 Years N A N A MZ and EZ Series Zero Tur
Download Pdf Manuals
Related Search