Humminbird Marine GPS System 3000 DEEP User's Manual
Contents
1. 2 Push the Rance knob An adjustment indicator appears at the lower right corner of the Cuanr WiNDOW 3 Turn the Rance knob y counterclockwise until the image of bottom is close to the bottom of the LCD display but still shows the area of interest Note As the depth of the water Mi increases the Leceno 3000 SERIES changes the depih range to keep the bottom on screen The Leceno 3000 Series uses a depth range to keep the bottom contour close to the bottom of the display To return the depth range to normal viewing turn the unit off and back on again using the Gain knob This is the only way to reset the depth range to normal viewing Optimized Display USING THE LEGEND 3000 SERIES MODES OF OPERATION OPTIMIZING THE DISPLAY Optimized Display showing second return Optimizing the Depth Range for Second Return To optimize the depth range for viewing the second return follow these steps 1 Make sure the Lecenp 3000 Series IS Operating in Automatic 2 Push the Rance knob An adjustment indicator appears at the lower right corner of the Chart Winbow 3 Turn the Rance knob clockwise until the second return is visible on the display 4 To return the depth range to normal viewing rotate the Rance knob counterclockwise until the depth range stops updating Second return Note The second return does not appear at many of the deeper depth ranges The appearance of t2. Simulator o p Power On with No Transducer Simulator If the LEcEND 3000 Series is powered On on with no transducer connected it 4 un 4 starts up in SimuLator mode No other steps are needed In this mode the Legend 3000 Series does not remember any setting changes after power off but defaults to the factory settings Power On with Transducer Connected If the Legend 3000 Series is powered on with the transducer connected the SimuLator must be turned on manually To turn on the SIMULATOR manually 1 Press the Control Panel knob to display the list of options 2 Rotate the Control Panel knob to scroll through the list until Simulator is visible and is highlighted on the display 3 Turn the Range knob to turn Simulator from Off to On 4 Press the Control Panel knob to clear the screen When operating with the Simulator on and the transducer connected changes made to the following Control Panel choices are permanently remembered Chart Speed RTS Window Surface Clutter Contrast White Line Units and in International Models Language www reelschematic com USER INTERFACE c The LEcEND 3000 User Interface is made up of the following components knobs and the LCD Display which in turn is made up of the RTS and the Chart Windows GAIN Knobs Four knobs on the LEcEND 3000 Series control all un user settings MoDE GAIN CONTROL PANEL and RANGE push gt Mode Knob CONTROL PANEL The Mope knob selects ho
3. 3000 Series is turned off The factory setting is 4 The GAIN knob applies the same gain BOkHz Goin Offset 5 O ANNA 10 menu allows for the gain applied to 50kHz signal as the 200kHz gain set by the GAIN knob Values higher The 50kHz GAIN OFFSET setting is retained in memory after the Legend 50kHz Gain Offset Deep Models Only increase decrease to the 200kHz and 50kHz signal performance This the 50kHz beam to be adjusted higher or lower than the GAIN knob setting to optimize it An offset value of 5 applies the same gain to the than 5 apply more gain to the 50kHz values lower than 5 apply less gain 3000 3005 Deep is turned off The factory setting is 5 White Line Whe Line activates and White Line y adjusts a feature which Off EBENE changes how the LEGEND eee 3000 Series draws the 3 bottom contour and E T structure and also 6 6m i E shows fainter sonar f returns more clearly ro When a Wurr Line setting of 1 to 8 is selected a light gray band highlights the strongest sonar returns within the sonar image and makes a distinctive outline Tad r E 60 10 White Line along the bottom contour structure and fish Selecting a larger numeric setting increases the width of the band and makes fainter sonar returns more noticeable but the Lecenp 3000 s ability to show subtle differences in bottom composition and structure is reduced Selecting a smaller numeric setting narrows the
4. We will make every effort to repair your unit within three business days from the receipt of your unit at our factory This does not include shipping time to and from our factory Units received on Friday are typically shipped by the following Wednesday units received Monday are typically shipped by Thursday etc All repair work is performed by factory trained technicians to meet exacting factory specifications Factory serviced units go through the same rigorous testing and quality control inspections as new production units After the original warranty period a standard flat rate service charge will be assessed for each repair physical damage and missing parts are not included Any repairs made after the original warranty will be warranted for an additional 90 days after service has been performed by our factory technicians You can contact our Customer Resource Center or visit our website to verify the flat rate repair fee for your product visit the Product Support section http www humminbird com We reserve the right to deem any product unserviceable when replacement parts are no longer available or impossible to obtain This Service Policy is valid in the United States only This applies only to Humminbird products returned to our factory in Eufaula Alabama This Service Policy is subject to change without notice CUSTOMER RESOURCE CENTER SERVICE POLICY SERVICE PROCEDURES Returning Your Unit for Service Before sending
5. activates an alarm that sounds when the surface water temperature changes to fall within or outside selected ranges These temperature boundaries help define bodies of water that are comfortable for and or are feeding zones for fish Upper and lower temperatures are set depending on the species of fish being sought Two basic actions can be selected to trigger an alarm either entering inside a temperature range or exiting moving outside a temperature range Both combines Inside and Outside settings alarming when crossing a temperature boundary The Temp Alarm can be muted by pressing the Control Panel knob once muted the alarm will not sound again until triggered by a new boundary crossing Temp Alarm Off d4 w p The Temp Alarm setting returns to factory default after the LecenD 3000 Series is turned off The factory setting is Orr Note You must select a Temp Alarm mode INsipE OUTSIDE Or Born then set the UPPER Tem and the Lower Temp in order for this feature to work Alarm Q Points Warmer Water Cooler Water Upper Temp is the upper temperature boundary for the temperature alarm The inside temp alarm will sound when the water temperature was initially above the upper temp boundary and then falls below it The outside temp alarm will sound when the water temperature was initially below the temp boundary and then rises above it Upper Temp Ge Es The Urrer Temp setting is retained in memory aft
6. band and shows greater variation in bottom composition Selecting Orr turns the Whrte Line feature off setting is Orr Filter n 4 m p algorithms on and off The Wurr Line setting is retained in memory after the Lecenp 3000 Series is turned off The factory Filter Fitter Dee Models only turns the filtering Select On to filter excess sonar noise Select Orr to show the greatest amount of sonar information The Farer setting is retained in memory after the 3000 Deep 3005 Deep is turned off The factory setting is ON Depth Alarm DEPTH ALARM activates a shallow water depth Depth Alarm 36 alarm The alarm will Drm gt sound when the digital depth becomes equal to or less than the setting The tone sounds at a rapid rate for several seconds and then sounds intermittently until the boat moves to deeper water The DEPTH Alarm can be muted by pressing the ControL PANEL knob once muted the alarm will not sound again until the boat moves to water deeper than the DEPTH ALARM setting International models have Depth Alarm settings in full metres from 1 m to 99m Note Remember that depth is measured from the transducer not from the surface of the water The Dert Alarm setting returns to factory default after the Lecenp 3000 Series is turned off The factory setting is Orr www reelschematic com USING THE LEGEND 3000 SERIES UPPER TEMP LOWER TEMP FISH ALARM FISH SENSITIVITY FISH ID Temp Alarm Temp Alarm
7. depth ranges and graph the information on the LCD display The Mode is selected by changing the Control Panel setting to Auto Manual or BTM Lock Bottom Lock Automatic Mode Automatic Move follows the bottom contour changing depth ranges as needed to keep the most recent sonar returns visible on the display Automatic Mone keeps the acquired bottom visible at all times showing sonar returns from the surface to the bottom and just beyond This is useful when traveling across the water in areas where the depth constantly changes requiring frequent range changes www reelschematic com In Automatic mode the Leceno 3000 Series selects the depth range best suited to keep recent sonar returns visible however the depth range can be adjusted to optimize the display for viewing the second return The display can also be optimized for maximum display resolution making it possible to distinguish fish very close together or close to the bottom Optimizing the Depth Range for Sonar Targets When the image of the bottom does not appear close to the bottom of the LCD display the Legend 3000 Series is not fully optimizing the display to show sonar targets such as fish that are very close together To enhance the ability of the unit to separate sonar targets and to optimize the display for maximum resolution follow these steps Automatic Mode 1 Make sure the Legend Pm 3000 Series is operating in Automatic Mode
8. for a long period of time it may take some time to wet the transducer when returned to the water Small air bubbles can cling to the surface of the transducer and interfere with proper operation These bubbles dissipate with time or you can wipe the face of the transducer with your fingers after the transducer is in the water Heat Damage Never leave the Lecenp 3000 Series in a closed car or trunk the extremely high temperatures generated in hot weather can damage the electronics www reelschematic com TROUBLESHOOTING Repairs Do not attempt to repair the Leceno 3000 Series yourself There are no user serviceable parts inside and special tools and techniques are required for reassembly to ensure the waterproof integrity of the housing Repairs should be performed only by authorized Techsonic technicians Before You Call Customer Support Many requests for repair received by Techsonic involve units that do not actually need repair These units are returned no problem found If you have a problem with your Lecenp 3000 Series use the following troubleshooting guide before calling Customer Support or sending your unit in for repair The Leceno 3000 Series contains several tools that can aid in determining if there is a problem as well as how to isolate and repair a problem in many cases 1 Nothing happens when turn the unit on Check the power cable connection at both ends Be sure the cable is connected correctly to a
9. from the surface of the water to a depth range sufficient to show the bottom For example in 18 feet of water a 20 foot depth range is selected The depth range scale can be controlled automatically or manually depending on the mode of operation In Automatic and Bottom Lock modes the LEceND 3000 Series selects the depth range In MANUAL mode the depth range is selected by the user Surface Clutter Y Depth Alarm OFF Turn RANGE To Adjust The sonar returns received by the Legend 3000 Series are displayed along the depth range scale in a REAL TIME SONAR RTS WiNpow and CHART Window The RTS WINDOW displays new sonar information within the transducer cone in an expanded easy to see format the Cuanr WinDow logs old RTS Winbow information to show a contour view of the bottom and structure Depth Temp and Speed readouts Chart Window Depth Range 1 Scale Real Tlme Sonar Window www reelschematic com USING THE LEGEND 3000 SERIES REAL TIME SONAR CHART WINDOW The sonar returns received by the Leceno 3000 Series are displayed along the depth range scale in a Rea Time SONARTM RTS Winbow and Chart Winbow The RTS Winpow displays new sonar information within the transducer cone in an expanded easy to see format the Chart Winpow logs old RTS Window information to show a contour view of the bottom and structure Real Time Sonar RTS Window RTS Wide A scope mode Real Time Sonar RTS
10. the most intense returns shown in black and less intense sonar returns shown as progressively lighter shades of gray When the view is narrow enough the combination of the grouping of the lines and the grayscale level helps to identify the bottom composition and structure The bottom displays as the largest grouping of black horizontal lines and typically has gray lines underneath A harder bottom shows less gray below a soft bottom shows more gray below Structure appears above the bottom as a cluster of lines with varying lengths and gray shades In any view fish appear as smaller groupings of sonar returns between the bottom and surface Often large fish within a structure will show as a strong return within a grouping of smaller returns When the boat is stationary or drifting very slowly the RTS Window can show the movement of the fish through the transducer beam Moving fish appear as smaller groups of lines that become progressively larger lines or vice versa A grouping of lines moving vertically indicates a fish changing depth The Ghart Window The CHART Window creates a historical log of sonar returns from stored RTS information As the boat moves variations in the depth and sonar return changes are charted to form an image of the bottom contour The most recent sonar returns are charted on the right side of the window as new information is received the older information is moved across the display The CHART Window also
11. 345 Window The REAL TIME SONAR RTS Winbow shows instantaneous sonar returns from the bottom structure and fish that are within the transducer beam The RTS Window updates with new sonar information up to 30 times per second in shallow water deeper water will slow the refresh rates The RTS Window responds to quickly changing depths in a way similar to a flasher type sonar display Interpreting the RTS information requires some skill comparing the RTS data with the data in Structure Bottom Less intense returns Intense returns Intense returns Fish Hard the CHART Window however Bottom makes the RTS information Soft Bottom easy to understand The width of the RTS Window Less can be adjusted to your intense returns preference Selecting a wider RTS WiNpow shows greater differences between the strength of the sonar returns although doing this will reduce the amount of history on the display See ConTroL PANELS for details on adjusting the RTS WiNDOW When the RTS Window is wide enough it plots the depth and intensity amplitude of a sonar return using horizontal black lines where line length indicates return strength and the vertical placement of the lines next to the depth range scale indicates the depth When the RTS Winbow is narrow enough it plots the depth and intensity of a sonar return using grayscale lines where the intensity of the sonar return is divided into 16 levels of grayscale with
12. Chart Winnow but some sonar returns will not be visible Selecting Wine makes the RTS Winpow wider and shows more of the sonar intensity information but less space on the LCD is available for sonar history Selecting Orr turns off the RTS Winpow and the entire LCD shows sonar history Note When the RTS Window is adjusted to Wide no grayscale information is shown The RTS Winbow setting is retained in memory after the LecenD 3000 Series is turned off The factory setting is NARROW USING THE LEGEND 3000 SERIES www reelschematic com SURFACE CLUTTER WHITE LINE FILTER DEPTH ALARM TEMP ALARM Surface Clutter SURFACE CLuTTER eliminates Surface Cutter 4 most sonar returns 1EBEN g near the water surface caused by trapped air boat wakes and temperature inversions Most surface clutter appears on the display because the strongest sonar returns come from the shallowest objects The Leceno 3000 Series uses a sophisticated feature called TVG Time Variable Gain to overcome surface clutter and counteract the effect of depth on sonar return strength The level 1 setting is optimal for making sonar information from all depths appear uniformly Many users however prefer to see more surface clutter than this setting shows Selecting a higher number shows more surface clutter but sonar returns nearest the surface will appear more intense than they actually are The Surrace Cutter setting is retained in memory after the Leceno
13. Legend 3000 series Operations Manual Operational instructions for Humminbird Legend 3000 Series including the Legend 3000 3005 3000 Deep and 3005 Deep www reelschematic com THANK YOU Thank you for choosing Humminbird America s 1 name in fishfinders Humminbird has built its reputation by designing and manufacturing top quality thoroughly reliable marine equipment Your Humminbird is designed for trouble free use in even the harshest marine environment In the unlikely event that your Humminbird does require repairs we offer an exclusive Service Policy free of charge during the first year after purchase and available at a reasonable rate after the one year period For complete details see the warranty included in with your unit We encourage you to read this operation manual carefully in order to get full benefit from all the features and applications of your Humminbird product Contact our Customer Resource Center at either 334 687 0503 or www humminbird com WARNING This device should not be used as a navigational aid to prevent collision grounding boat damage or personal injury When the boat is moving water depth may change too quickly to allow time for you to react Always operate the boat at very slow speeds if you suspect shallow water or submerged objects Legend Humminbird WhiteLine RTS Fish ID Structure ID TrueArch are trademarked by or registered trademarks of Techsonic Indust
14. TING READOUT Contrast The Controt Pane Name indicates the feature the Serre Inpicator Shows the Depth Alarm Off current setting within the complete range of adjustment and the SErriNG ReapouT Shows the status when CONTROL PANEL is not selected Setting Readout Control Panel Name To select a ControL Pane feature for adjustment follow these Setting steps Indicator 1 Press the ControL Pane knob A list of options appears on the display The option currently selected for adjustment is indicated by a white background color 2 Rotate the Contro PaneL knob to select the desired option for adjustment Clockwise rotation selects options higher in the list counterclockwise rotation selects options lower in the list Note Not all options in the list can be viewed on the display at one time When the selected option is at the bottom of the list continue turning the knob to display other options 3 Once the desired option is selected turn the Rance knob to adjust Adjustments are made immediately and are shown by an indicator on the selected ControL PANEL 4 Remove the Control Panes by pushing the ControL PANEL knob Alternately after a few seconds with no knob press turn activity the ControL PaneLs are removed from the display automatically Mode The first Control Panel to set is Mode Three modes of operation control the method used by the Legend 3000 Series to track the bottom select
15. ains several extra features that will enhance its sonar performance in deep water SONAR View allows you to display the sonar information from either beam or both beams simultaneously FILTER control allows the filtering algorithms to be turned off to show the greatest amount of sonar information FisH ALARM FISH Sensitivity and FisH ID provide advanced signal processing to identify fish and show their depth and relative size from either beam Powering Up the Unit After installation turn the LEcEND 3000 Series on by momentarily pressing the Gain knob An audible chirp sounds as the unit turns on If the unit detects that the transducer is connected and is in water the Legend 3000 SERIES begins to show sonar information on the display If the transducer is not detected the unit starts up in SIMULATOR mode To power the unit off at any time press and hold the Gain knob for several seconds until the unit turns off Simulator and Feature Memory The Legend 3000 Series contains a SIMULATOR that allows you to use the unit as though you are on the water The SIMULATOR is an invaluable aid to learning the features and functions of the LEcENp 3000 Series All controls are operational and settings can be changed to experiment with various features An indicator appears at the bottom left of the display when operating in SIMULATOR mode There are two ways to start the SimuLator The method to use depends on whether a transducer is connected
16. d indicates the selected feature Turn the RANGE knob to adjust the selected feature Remove the ConTroL PANEL list from the display by pushing the ControL PANEL knob again If no adjustments are made after a few seconds the ConTROL PANEL list is removed automatically Range Knob The Rance knob adjusts the depth ranges used on the display The RANGE knob has slightly different capabilities in each mode of operation See Modes of Operation for specific information In all modes turning the knob clockwise increases the range while turning it counterclockwise decreases the range Turning the knob slowly increases the adjustment in USING THE LEGEND 3000 SERIES USER INTERFACE KNOBS LCD DISPLAY small increments while turning it quickly makes large changes to the adjustment The LCD Display The Legend 3000 Series uses a high Turn CONTROL To Select resolution LCD display to show sonar Light 8 Off BEEEEEEN 3 RTS Window d information digital depth temperature speed and other readouts A digital depth readout is always displayed in the upper left corner of the LCD When the speed temp accessory is connected additional digital readouts such as MPH are shown below the depth A voltage readout appears in the bottom left when the input voltage to the LEGEND 3000 SERIES is less than 11 volts or greater than 15 volts A depth range scale appears close to the right side of the LCD display This scale indicates the distance
17. er the LecenD 3000 Series is turned off The factory setting is 78 F 26 C Lower Temp is the lower temperature boundary for the temperature alarm The inside temp alarm will sound when the water temperature was initially below the lower temp boundary and then rises above it The outside temp alarm will sound when the water temperature was initially above the temp boundary and then falls below it Lower Temp 61 0 mm 39 The Lower Temp setting is retained in memory after the Legend 3000 Series is turned off The factory setting ig 72 F 22 Fish Alarm FisH ALarm Deep Models only will sound when a fish or other target not connected to the bottom that meets the selected size criteria is detected by the sonar The Fish ALarm has four different settings Orr plus the three different fish symbols shown onscreen see Fish ID The 3000 Deep 3005 Deep can be set to alarm only large fish displayed as a large fish symbol only large and medium fish displayed as one large and one medium fish symbol or all sizes of fish displayed as one large one medium and one small fish symbol Fish Alarm cae De a The Fish Alarm setting is retained in memory after the 3000 Deep 3005 Deep is turned off The factory setting is OFF Fish Sensitivity Fish Sensitivity Deep Models only adjusts the sensitivity of the fish detection algorithms separately from the sonar gain control Knob Selecting a positive offset makes the
18. finder of the future Minimal easy to understand knob controls provide access to the most important features The Legend 3000 Series eliminates confusion created by too many buttons and menus High technology high performance with back to basics operation makes the LecenD 3000 Series the ideal choice of the serious angler The LecenD 3000 Series uses sonar to locate and define underwater objects sonar technology is based on sound waves sent into the water in a controlled beam from the transducer Objects within this beam reflect the sonar signal back The Legend 3000 SERIES very accurately measures the distance to these objects based on the time it takes for the sonar to return Each object bottom fish or structure reflects the sonar uniquely providing information about its makeup The LecenD 3000 Series draws this returned information on the display The LecenD 3000 Series operates in a wide variety of water conditions from 2 to 600 2000 for the Legend 3000 Deep and 3005 Deep Models Actual depth Capability depends on many factors such as bottom hardness water conditions and transducer installation All sonar units typically read to deeper depths in fresh water than in salt water Deep Models Additional Performance If you purchased a Legend 3000 Deep or a Legend 3005 Deep Model your Legend product is equipped with a 50kHz 200kHz dual beam transducer capable of performing to a depth of 2000 feet In addition your unit cont
19. fish detection more sensitive 5 greatest sensitivity Selecting a negative offset makes the fish detection less sensitive 5 least sensitivity Fish 4 d The Fish Sensitivity setting is retained in memory after the 3000 Deep 3005 Deep is turned off The factory setting is 0 Fish ID Fish ID Deep Models only uses Fish ID advanced signal processing to d Fresh l evaluate further any sonar return between the surface and the bottom If the return meets certain additional criteria a fish symbol will be assigned There are three different fish symbols to indicate the intensity of the sonar return While signal intensity is a good indicator of fish size www reelschematic com MAINTENANCE AND WARRANTY CONTROL PANELS MAIN TENANCE TROUBLESHOOTING different species of fish have different sonar characteristics so it is not always possible to distinguish fish size amongst varying species Selecting Fresuwater will adjust the algorithms toward freshwater species of fish while selecting Sattwater will adjust the algorithms towards saltwater species Note The signal intensity is normalized for depth so that a small fish close to the boat will not appear as a large fish symbol The digital depth of the designated fish is also shown to help locate the fish vertically This is especially helpful in setting bait depths or for downrigger operation The FisH ID setting is retained in memory after the 3000 Deer 3005 Dee
20. h Bensitivity Sy E AN 11 BEhID 0 Qo ccc ccc cee ee eee AR 11 Emgator 4 _ lt a 11 WMA MM AAA AN ow 11 andllage O EE o v ev eveuesueunu 11 Section 2 MAINTENANCE AND WARRANTY sss 12 Maintenan e 4 A LLvuveuveuveuun 12 TroubleshooWgg g MEA ee 18 Warranty MA Be eee eee 14 SENVICE POlICV A e dd he aah a ewe 15 Customer Support im a nn n nn n n n n 15 Section 3 SPECIFICATIONS Legend 3000 3005 Specifications a oaa 16 Legend 3000 Deep 3005 Deep SpecificatiOnS 16 www reelschematic com USING THE LEGEND 3000 SERIES PERFORMANCE SIMULATOR POWERING UP THE UNIT Legend Models North T American International 1000 1005 2000 2005 o 1000 Series 160 x 160 pixels 8 levels grayscale Single Beam 2 to 600 2000 Series 3000 3005 Dual Beam 240 x 240 pixels o m ALL 2 to 600 16 levels grayscale Ez 2 1000 Deep 1005 Deep Dual Beam 3000 Series S 2000 Deep 2005 Deep 2 to 2000 240h x 320v pixels 3000 Deep 3005 Deep 16 levels grayscale Note International models include multiple languages and measurements in metres feet or fathoms Temperature includes jC USING THE LEGEND 3000 SERIES Performance The Legend 3000 Series represents a new way of thinking about fishing electronics It combines state of the art electronics with the detail of a traditional sonar paper chart recorder to create the fish
21. h the unit and the transducer Also make sure that the transducer is fully submerged in water If the transducer is connected to the unit through a switch temporarily connect it directly to the unit and try again If none of these items identifies an obvious problem the transducer itself may be at fault Be sure to include the transducer if returning the unit for repair To override the SimuLaror manually select the SiwuLATOR Control PaneL and turn to Orr See Control Panels for more information 3 There is no bottom reading visible on the display There are several possible causes for this condition If the loss of bottom information occurs only at high boat speeds the transducer needs to be adjusted If the digital depth readout is working but there is no bottom visible on screen it is possible that the depth range has been adjusted manually to a range lower than that needed to display the bottom Also in very deep water it may be necessary to increase the Gain setting manually in order to maintain a graphic depiction of the bottom If you are using a transducer switch to connect two transducers to the Lecenp 3000 Series make sure that the switch is in the correct position to connect a transducer and that the transducer is submerged in water If a trolling motor transducer is selected and the trolling motor is out of the water no sonar information will appear If none of the above solves the problem inspect the transduce
22. he second return depends on depth of the water water conditions bottom hardness and the gain setting The Lecenp 3000 Series operates with this offset depth range until it is returned to the original settings or the unit is turned off after which the unit defaults to factory settings www reelschematic com USING THE LEGEND 3000 SERIES BOTTOM LOCK ZOOM MODE MANUAL MODE Hode 4 BtmLock Bottom Lock Zoom Mode agp 0 Bottom Lock Zoom Mode Bm Lock Bottom Lock mode tracks the bottom similarly to Automatic mode however the display shows a full range view on right and a zoomed window on the left The zoomed window provides added display resolution for separating sonar returns that are very close together such as those caused by fish suspended close to the bottom Zoom Preview Bars Window As the depth changes the Leceno 3000 SERIES automatically keeps the bottom visible in the zoomed window and the full range view In the full range view horizontal zoom preview bars define the area of bottom being enlarged The default setting varies based on the depth range however this setting can be changed to show more area around the bottom or to show the bottom in greater detail i Adjustment Indicator To change the area of the bottom being zoomed follow these steps 1 Make sure the Leceno 3000 Series is operating in Brm Lock Bottom Lock mode 2 Push the Ranee
23. indicates the composition of the bottom A hard bottom such as compacted sediment or flat rock appears as a dark thin line across the display A soft bottom such as mud or sand appears as a thicker line that contains a transition from darker to lighter grays Bottoms made up of many rocks have a broken random appearance Sloped Bottoms Bottoms having a large degree of slope also present a unique picture These generally have a thicker black band representing the bottom directly under the boat Equal areas of gray above and below the black band represent sonar returns from around the boat Second Sonar Returns A second sonar return may be visible if the appropriate depth range is selected This appears as a ROcky depth contour below the main E d bottom contour at twice the depth The second return occurs when the n Bottom sonar signal bounces between the bottom and the surface of the water then back again Some anglers use the appearance of the second return to determine bottom hardness With a lower gain setting the second return will be more faint except in areas with a hard bottom The Lecenp 3000 Series has a unique depth range feature which permits the second return to be visible in any depth range up to one half the maximum depth of the unit See Mones or Operation for details Chart Window Hard Bottom Structure The Lecenn 3000 Series displays structure such as submerged grass brush trees and wrecks
24. installation and operation instructions e Damaged or has failed because of an accident or abnormal operation e Repaired or modified by entities other than Techsonic Industries Please retain your original receipt as a proof of the purchase date This will be required for in warranty service THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES OBLIGATIONS OR LIABILITIES ON THE PART OF TECHSONIC INDUSTRIES AND WILL BE THE CUSTOMER S EXCLUSIVE REMEDY EXCEPT FOR ANY APPLICABLE IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE HEREBY LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE IN NO EVENT WILL TECHSONIC INDUSTRIES BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE PRODUCTS Some states do not allow limitations on an implied warranty or the exclusion of incidental or consequential damages so the above exclusions may not apply to you You may also have other rights which vary from state to state A separate Warranty is provided by international distributors for the international models This warranty is included by your local distributor and this distributor maintains local service for your unit www reelschematic com Techsonic Industries Service Policy Even though you ll probably never need to take advantage of our incredible service policy it s good to know that we back our products this confidently We do it because you deserve the best
25. is ssa es 20 and 74 at 10 dB Power Requirement o ooooooom o o 10 20 VDC DODIY ur dard doo cion od ici ee 8 level FSTN Grayscale LCD AUD raa sea ROO ae RACE cee RORIS 160H x 160 V Viewing Area sss n 395 Hx 3395 V DAOUNUNG iar aci aci e RE ede eic aci Ra In dash or Gimbal quic Wa 41346 V x 6 6 W x 224 D mE V li i ieiecccecc Dual beam Transavcemcane Length A 20 6 metres 3005 3005 DEEP SPECIFICATIONS INTERNATIONAL MODELS Languages Supported Include English Dansk Deutsch Espa ol Finnish Svomi Francais Italiano Nederlands Norsk Portuqu s Svenska Magvar and Polski Additional units of measurement Metres Fathoms and C
26. knob An adjustment indicator appears by the lower zoom preview bar indicating this is the selected depth limit for adjustment Note Pushing the Rance knob toggles between the upper and lower zoom preview bar adjustment If the lower zoom preview bar is to be adjusted push the Rance knob until it is Selected 3 Rotate the Rance knob to adjust the zoom preview bar Moving the zoom preview bars closer together increases the display resolution in the zoomed window moving them further apart decreases display resolution but allows more area around the bottom to be viewed The indicators disappear after several seconds with no adjustment The Lecenp 3000 Series continues to follow the bottom using the new range Any change made to the zoom preview bars is remembered until the Leceno 3000 Series is powered off when the unit defaults to factory settings Manual Mode ManuaL mode turns off automatic bottom tracking leaving control of the depth range to the user Both the upper and lower depth ranges can be adjusted to show the bottom or any other desired depth in greater detail When first i switched to Manua mode the LEGEND 3000 Series defaults to the current automatic depth range however after the manual depth ranges have been set the Lecenp 3000 SERIES uses the new settings until it is powered off when it defaults to factory settings Manual Mode ManuaL mode works best in areas of relatively fla
27. n of the problem e Return product freight prepaid to Techsonic Industries Inc using an insured carrier with delivery confirmation Contacting Humminbird Contact the Humminbird Customer Resource Center in any of the following ways By Telephone Monday Friday 8 00 a m to 4 30 p m Central Standard Time 334 687 0503 By e mail typically we respond to your e mail within three business days custserv techsonic com For direct shipping our address is Techsonic Industries Inc Service Department 108 Maple Lane Eufaula AL 36027 USA 15 www reelschematic com SPECIFICATIONS 3000 3005 SPECIFICATIONS Operating Frequency lisse m 200 kHz POWSFDITIDIJE os ssec ch o ERE aes 4000 Watts Peak to Peak Ho 500 Watts RMS Area of Coverage cerrara adc E RR E CR EORR 24 at 3 dB Power Requirement cece eee n 10 20 VDC buc T 8 level FSTN Grayscale LCD CITA Croscutaestacatsreram aretacataturxcu iur deca cure a n 160H x 160 V Viewing Area ssess n 3 Hx 33 V LLO Lo eden er mar diac ete Sedo Er a ea de d In dash or Gimbal En OOS rr 41346 V x 62e W x 224 D Transducer lt lt single beam Transducer Cable Length WN 20 6 metres 16 3000 DEEP 3005 DEEP SPECIFICATIONS Operating Frequencies oooooooo o o 50 200 kHz Power Output 0 cc nnne 4000 Watts Peak to Peak nM 500 Watts RMS Area of Coverage is
28. nge an arch appears Boat speed the CHART SPEED setting and movement of the fish greatly affect the shape of the arch When the boat and the fish are moving slowly relative to each other the fish creates an elongated arch When the boat and the fish are moving quickly relative to each other the fish creates a shorter arch A partial arch forms when the fish does not move through the entire cone angle USING THE LEGEND 3000 SERIES CHART WINDOW BOTTOMS FISH APPEARANCE Note It i S Bait fish Fish Arch Partial Fish Arch Structure important to remember that sonar cannot distinguish between a fish and some other object suspended in the water Regardless of the object the sonar detects it has the possibility of being drawn as an arch Sonar Views Deep Models Only The dual beam 50 200kHz sonar information can be displayed in several different views in the Chart Winbow In the 200kHz view only the sonar returns and Fish ID from the 200kHz beam are displayed Typically the 200kHz information provides greater bottom detail up to 800 and works well while the boat is in motion The 50kHz view only shows the sonar returns and Fisu ID from the 50kHz beam The 50kHz information provides depth accuracy up to 2000 and shows more targets in its wider beam The Split Screen view shows the 50kHz and 200kHz sonar information in side by side windows on the display The 200kHz 50kHz view is a composite of the 200kH
29. oms KPH displays depth in fathoms speed in kilometres per hour The Uurrs settings are retained in memory after the unit is turned off Language Lancuace International Models only selects the language for text used in the Controt PANELS and for messages See the LEGEND 3005 3005 Deer Specifications for included languages 4 Eng LANGUAGE setting is retained in memory after the LEcEND 3005 3005 Deer Is turned off The factory setting is ENGLISH MAINTENANCE Your Leceno 3000 Series is designed to provide years of trouble free operation with virtually no maintenance Follow these simple procedures to ensure your LEGEND 3000 Series continues to deliver top performance Cleaning If the unit comes into contact with salt spray simply wipe the affected surfaces with a cloth dampened in fresh water Do not use a chemical glass cleaner on the lens as chemicals in the solution may crack the lens When cleaning the LCD protective lens use a chamois and non abrasive mild cleaner Do not wipe while dirt or grease is on the lens Be careful to avoid scratching the lens If your boat remains in the water for long periods of time algae and other marine growth can reduce the effectiveness of the transducer Periodically clean the face of the transducer with liquid detergent Pivoting the transducer up in the bracket may allow better access for inspection or cleaning Wetting the Transducer If your boat remains out of the water
30. on the bottom Structure can be distinguished by comparing the area just above and below the main bottom return Usually structure shows as areas of dark to light gray on top of a dark bottom contour The appearance of structure is greatly affected by boat speed and direction to repeat the same image it is often necessary to travel the same speed and direction over the location where the structure was originally located www reelschematic com Thermocline Return Thermoclines The LecenD 3000 Series is also capable of showing layers of water having different temperatures These temperature differences called thermoclines appear at different depths depending on current conditions A thermocline typically appears as a continuous band of many gray levels moving across the display at the same depth Thermoclines always appear above the bottom Fish Appearance Schools of bait fish as well as individual fish are clearly visible on the Legend 3000 Series display Bait fish appear as clouds having different shapes and sizes depending on the number of fish and boat speed Individual fish appear as smaller black and gray lines often appearing as a fish arch A fish arch may form as the fish moves through the sonar beam Due to the transducer beam angle the distance to the fish decreases as the fish moves into the beam and then increases as it moves out again When the CHART WiNDOW graphs this distance cha
31. peller cavitation can appear as noise on screen If the transducer is mounted too close to the propeller the turbulence generated can interfere with the sonar signal Ensure that the transducer is mounted at least 15 38cm from the prop 10 The screen does not display a full fish arch Check the running angle of the transducer If the running angle is too great a full fish arch may not appear Reduce the running angle of the transducer Several incremental adjustments may be necessary 14 TECHSONIC INDUSTRIES INC ONE YEAR LIMITED WARRANTY We warrant the original retail purchaser that products made by Techsonic Industries have been manufactured free from defects in materials and workmanship This warranty is effective for one year from the date of original retail purchase Techsonic Industries products found to be defective and covered by this warranty will be replaced or repaired free of charge at Techsonic Industries option and returned to the customer freight prepaid Techsonic Industries sole responsibility under this warranty is limited to the repair or replacement of a product that has been deemed defective by Techsonic Industries Techsonic Industries is not responsible for charges connected with the removal of such product or reinstallation of replaced or repaired parts This warranty does not apply to a product that has been e mproperly installed e Used in an installation other than that recommended in the product
32. r cable from end to end for breaks kinks or cuts in the outer casing of the cable and repair after disconnecting the cable from both the unit and the transducer If the transducer is connected to the unit through a switch temporarily connect it directly to the unit and try again If none of these items identifies an obvious problem the transducer itself may be at fault Be sure to include the transducer if returning the unit for repair 4 When in very shallow water get gaps in the bottom reading and inconsistent digital depth indications The Leceno 3000 Series will work reliably in water 2 6m or deeper Remember that the depth is measured from the transducer not necessarily from the surface of the water 13 www reelschematic com MAINTENANCE AND WARRANTY TROUBLESHOOTING WARRANTY SERVICE POLICY 5 The unit comes on before press POWER and won t turn off Check the transducer cable if the outer jacket of the cable has been cut and the cable is in contact with bare metal you need to disconnect the cable from the unit then repair the cut with electrical tape If there is no problem with the cable disconnect the transducer from the unit and see if the problem is corrected to isolate the source of the problem 6 get gaps in the reading at high speeds Your transducer needs to be adjusted If the transducer is transom mounted there are two adjustments available to you height and running angle Make small adjus
33. r is turned off The factory setting is Off Simulator SimuLaror allows the Lecenp 3000 Simulator Series to operate in simulated 4 Un b sonar mode This is useful for learning the features and functionality of the Leceno 3000 Series when not on the water Settings to Control Panels that are retained in normal operation will be retained in Simulator Mode if a transducer is connected When operating with the Simulator on and without a transducer connected the Legend 3000 Series does not remember any changes to settings The Simulator setting defaults to factory settings after the Legend 3000 Series is turned off Units Units selects the units of measure for boat speed Selecting KTS displays the speed in nautical miles per hours MPH displays the speed in miles per hour Units selects the units of measure for boat speed and depth in one of two combinations supported by every LEcEND 3000 SERIES Unite dq Mph p e Feer MPH displays depth in feet and speed in miles per hour e Feet KTS nisrLays depth in feet and speed in nautical miles per hour Units also selects the units of measure for boat speed and depth in one of four additional combinations supported by the International Models only e Merres KPH displays depth kilometres per hour e MtrnES KTS displays depth in metres speed in nautical miles per hour e FatHoms KTS displays depth in fathoms speed in in metres speed in 12 nautical miles per hour e FatH
34. reliable power source red lead to positive black lead to negative or ground Ensure the power available at the mount is between 10 and 20 VDC If the unit is wired through a fuse panel ensure the panel is powered accessory fuse panels often are controlled by a separate switch or by the boat s ignition switch A fuse also can appear to be good when in fact it is not Check the fuse with a tester or replace it with a fuse known to be good Check the power connection to the Lecenp 3000 Senis It is possible to force the power cable connector into the collector plug incorrectly If the connector is reversed the unit will not work Examine the contacts on the back of the unit to ensure there is no corrosion Ensure the cables are properly installed into the collector plug and the collector plug is properly seated into the Leceno 3000 SERIES 2 he unit starts up in Simulator mode The Lecenb 3000 Series has the ability to detect that a transducer is connected If at power up a transducer is not connected the unit starts up in Simulator mode Ensure that an appropriate transducer connector is used and the connector is positioned correctly in the collector plug Also be sure that the collector plug is fully seated into the unit Next inspect the transducer cable from end to end for breaks kinks or cuts in the outer casing of the cable and repair after MAINTENANCE AND WARRANTY TROUBLESHOOTING disconnecting the cable from bot
35. ries Inc 2003 All rights reserved WARNING Disassembly and repair of this electronic unit should only be performed by authorized service personnel Any modification of the serial number or attempt to repair the original equipment or accessories by unauthorized individuals will void the warranty Handling and or opening this unit may result in exposure to lead in the form of solder WARNING This product contains lead a chemical known to the State of California to cause cancer and birth defects and other reproductive harm www reelschematic com TABLE OF CONTENTS Section 1 USING THE LEGEND 3000 SerieS 0000 eee eee 2 W EETERTTTTTTCCRTTECQOT TT TT TT PETRI 2 Deep Models Additional Performance o o o o 2 Powering Up the Unit llis n 2 Simulator and Feature Memory osuna 2 User Interface erat eta aa d A A III 3 EOD IG OIAV Tr 3 Real Time Sonar Window 0 0 0c ees 3 Chart WINd0OW e RR 4 Control Papai SE ee 6 Magee a ID coo 6 Automatic MOde 0 A a i Bettom Lock SMOKE 8 06 NS ae Y 8 O SRT PA wv 9 AMO PAS TEA SR 9 OS AAA ee Y WI 9 Entra M eE GRA 9 ATSAMINOW dE A ATT 9 Surface Clutter o borro 10 Whiteblng 5 A LL MA 10 Filter M LP FRA Be 10 Depth Aarm gM am lS A 10 Temp Alarm A SA S MEM 11 ash Bam MB o 11 E
36. settings after the unit is turned off Chart Speed CharT SPEED selects the speed at which the bottom information moves across the display Options available range from 1 very slow to 8 very fast Selecting a faster rate shows more information in the Chart Winbow but it moves across the display very quickly Selecting a slower rate keeps the information on the display longer but the chart information becomes compressed and may be more difficult to interpret Setting CharT Speed in relation to boat speed is often preferred Chart Speed 6 1lEEEEEB 8 The Chart SpeeD setting is retained in memory after the LEGEND 3000 Series is turned off The factory setting is 6 Sonar View Sonar View Deep Models only Sonar Views selects the source of the 4 mx p sonar information being displayed 200kHz displays sonar information and Fisu ID Ip a from the 200kHz beam only 1E p 50kHz displays sonar information and Fish ID from the 50kHz beam only Spur Screen presents the sonar information from the 200kHz and 50kHz beams simultaneously in side by side windows 200kHz 50KHz displays the sonar information from the 200kHz beam and target information from the 50kHz beam The Sonar View setting is retained in memory after the unit is turned off The factory setting is 200kHz y 7 y e a Fa SSmus metes MO A NO F M dba e Uh 50kHz 200kHz 20 Split window 50kHz 200kHz shown with metric depth C and kph digital readou
37. t bottom or if you are trolling slowly It is also ideal for displaying a small area of the overall depth range in great detail if you are looking for fish at a specific depth To adjust the depth ranges manually follow these steps 1 Make sure the Legend 3000 oeries is operating in Manual mode 2 Push the Range knob An adjustment indicator appears at the location of the Lower A Depth Range indicating that it is ready for adjustment A Lower Depth Range Adjustment Indicator Note Pushing the Range knob toggles m between the upper and lower depth Upper Depth Range range selection If the Upper Depth Y Stiment Indicator Range is to be adjusted push the Range knob until it is highlighted 3 Rotate the Rance knob to adjust the Depth Range Clockwise rotation increases the depth counterclockwise rotation decreases the depth The display updates as the changes are made www reelschematic com USING THE LEGEND 3000 SERIES CHART SPEED SONAR VIEW LIGHT CONTRAST RTS WINDOW After several seconds without pressing or turning the knob the Dert Rance adjustment indicator will disappear from the screen automatically The Leceno 3000 Series does not make adjustments to keep the bottom information on screen If the depth is deeper or shallower than the ranges on the display the bottom contour will not be visible The manual range settings made to the Lecenp 3000 Series default to factory
38. tments and run the boat at high speeds to determine the effect It may take several tries to optimize high speed operation This can also be a result of air or turbulence in the transducer location caused by rivets ribs etc 7 My unit loses power at high speeds Your LEGEND 3000 Series has over voltage protection that turns the unit off when input voltage exceeds 20 VDC Some outboard motors do not regulate the power output of the engine s alternator effectively and can produce voltage in excess of 20 volts when running at high RPMs The LEcEND 3000 Series displays input voltage in the lower left corner of the display when it exceeds 15 VDC Use this readout to determine if the voltage exceeds 20 VDC 8 The screen begins to fade out Images are not as sharp as normal Check the input voltage The LecenD 3000 Series will display the current voltage on screen if it is greater than 16 or less than 10 VDC The voltage readout will appear in the bottom left corner of the screen 9 The display shows many black dots at high speeds and high sensitivity settings You are seeing noise or interference caused by one of several sources Noise can be caused by other electronic devices Turn off any nearby electronics and see if the problem goes away Noise can also be caused by the engine If engine noise is causing the interference the problem will intensify at higher RPMs Increase the engine speed with the boat stationary to isolate this cause Pro
39. ts available on international models Light Leht activates the display backlight and selects the OFF BEN 8 brightness level The backlight is manually controlled except when the unit first powers up During initial power up the backlight turns on at full brightness so the display will be visible at night The backlight will then begin to decrease in intensity automatically until it is off in order to save energy Selecting the ConrroL PaneL List choice stops the automatic off process keeping the backlight on at the intensity level selected The Light setting defaults to factory settings after the Legend 3000 Series is turned off The factory setting is ON full at power up and automatic decrease to Orr Contrast Contrast enhances the viewability of the LCD by making it darker or lighter Selecting a higher number darkens the display selecting a lower number lightens the display The Lecenn 3000 Series uses sophisticated electronics to adjust the contrast level automatically however at times of extreme heat or cold manually adjusting the contrast for best display may be needed Controst 8 Ol 6 The Contrast setting is retained in memory after the unit is turned off as long as it is set between 6 and 10 The factory setting is 8 RTS Window RTS Winbow selects the width of RTS Window the window dedicated to REAL 4 Wide gt TIME SONAR M Selecting Narrow decreases the width of the RTS Winbow leaving more space for the
40. w the Legend 3000 SERIES locates the bottom and graphs the information on the display Turn the knob until the pointer aligns with the desired mode of operation See Modes of Operation for more information Gain Knob The GAIN knob controls the gain sometimes called sensitivity of the sonar receiver Gain also powers the E unit on or off When the Leeenn 3000 2 1 SERIES is off press Gain to turn the unit on Press and hold Gain to turn the unit off Turn the Gain knob clockwise to increase the gain turn counterclockwise to decrease the gain As you turn the knob only new sonar information being graphed m shows the effect of the gain change D Increasing the gain shows faint sonar PERMISO returns from small bait fish and suspended debris in the water but the display may become too cluttered in some water conditions Increased gain is also beneficial at deeper depths to maintain a good bottom image and show adequate sonar returns from deep objects Decreasing the gain eliminates the clutter from the display however if adjusted too low the display may not show many faint sonar returns that could be fish Push to Select RANGE Push to Select Maximum Gain Low Gain Medium Gain Control Panel Knob The CowrRoL PANEL knob accesses features used to adjust some LEGEND 3000 Series settings Push the knob to display the ConTROL PANEL list then rotate the knob to select a feature for adjustment A light colored backgroun
41. your unit in for repair please contact the factory either by phone or by email to obtain a Repair Authorization Number for your unit Please have your product model name and serial number available before calling the factory If you contact the factory by e mail please include your product model name and serial number in the e mail and use Request for Repair Authorization Number for your e mail subject header You should include your Repair Authorization Number in all subsequent communications about your unit For IN WARRANTY service complete the following steps e Obtain a Repair Authorization Number from Techsonic Industries Customer Resource Center e Tag product with your customer name street address phone number and your assigned Repair e Authorization Number e Include a brief written description of the problem e Include a copy of your receipt to show proof and date of purchase e Return product freight prepaid to Techsonic Industries Inc using an insured carrier with delivery confirmation For OUT OF WARRANTY service complete the following steps e Obtain a Repair Authorization Number from Techsonic Industries Customer Resource Center e Included payment in the form of credit card number and expiration date money order or personal check Please do not send cash e Tag product with your customer name street address phone number and your assigned Repair Authorization Number e Include a brief written descriptio
42. z sonar information and the target information from the 50kHz sonar See CONTROL PANELS for details on selecting the sonar views Fish Arch Diagram www reelschematic com USING THE LEGEND 3000 SERIES SONAR VIEWS CONTROL PANELS CONTROL PANELS Control Panels provide access to important but infrequently adjusted features such as Chart SPEED MODE SONAR VIEW LIGHT CONTRAST RTS WINDOW SURFACE CLUTTER WHITE LINE FILTER DEPTH ALARM TEMP ALARM FISH ALARM FISH Sensitivity FisH ID SimuLATOR Units and in International Models only LANGUAGE Control Panels allow you to set the mode of operation as well as additional features Use the Move to change the bottom tracking and depth range method of display then use the other Control Panels to add features to your selected mode of operation Note Only the International Models 3005 and 3005 Deep contain a Language choice in the Control Panel and only the International Models support multiple units of measure such as fathoms and metres Turn CONTROL To Select AA Acti Note The Sonar View Fish contro Panel Chart Speed 5 ID Fish Al Fish Fis arm Fis Light Off MOM 5 Sensitivity and Filter choices only appear on the Deep Model Control Panels ControL Panes are displayed by using the ControL PaneL knob and adjusted by using the Rance knob The active ControL PaneL consists of three parts the ControL PaneL NAME SETTING INDICATOR and SET
Download Pdf Manuals
Related Search