Huffy SKM 3072-U User's Manual
Contents
1. Support pole on support table Attach backboard components under assembly to top pole section 12 NOTE Two people are recommended for this step use caution elevator component under assembly is heavy Then install pole cap 42 NOTE Protecting goal rim with cardboard will prevent scratches P N 205343A 7 97 8 da Roll completed assembled component to DO NOT LEAVE desired position Fill base with water COMPONENTS UNDER approx 106 liters 28 gallons or sand ASSEMBLY UNATTENDED approx 102 kg 225 Ib and snap cap WHEN EMPTY MAY TIP OVER 43 in place Secure component to ground using rope 44 and tie down stake 45 IMPORTANT Add 7 6 liters two gallons of NON TOXIC ANTIFREEZE in sub freezing climates 25 Make final adjustments to level the goal rim If the Insert the end of a broom handle or wooden backboard and goal rim are tipped back raise collar 12 bar 19 22 mm 3 4 7 8 diameter into the until level and tighten If backboard and goal rim are release lever tipped forward lower collar 12 until level and tighten Maximum adjustment travel is 81 91cm 32 to 36 from bottom of pole to top of collar 12 Adjusting the Height IMPORTANT Push up pivot toward pole and lower to lock Push up and pivot bar away from pole to raise and lower Regulation goal rim height Broom Handle is 3 05 m 10 feet A or Wooden Bar A not included P N 205343A 7 97 9 ro PARTS L2. 3 NOTE Two people recommended for this step Install bolt 18 washer 10 and nut 11 in pole Secure pole bottom 13 to base using nut 7 and collar 12 at tape mark on bottom pole and tighten disk 18 a deep socket is recommended IMPORTANT DO NOT OVER TIGHTEN STEP 12 OR 13 MAY CRACK BASE P N 205343A 7 97 5 IMPORTANT Test fit bolts into holes of brackets 19 and carefully rock them in a circular motion to ream out paint from holes if necessary IMPORTANT Finger tighten nuts and bolts until instructed to fully tighten later Fit spacer 22 into pawl 23 and fit pin of pawl through end hole of release lever 24 IMPORTANT Bolt 28 must be inserted through tube 29 spacer 30 support bracket 21 board bracket 19 release lever 24 wave washer 31 and then ratchet 32 Fully tighten all nuts and bolts after assembly Use pliers to stretch spring 34 into position P N 205343A 7197 6 e 19 Starting with nuts 11 flush against bracket 19 secure goal rim 37 and bracket 19 to backboard NOTE Mounting nuts and bolts supplied with goal rim hardware Fold bracket 19 to line up with holes in backboard and secure IMPORTANT For spring loaded goal rim assembly refer to instructions included with goal rim hardware 1 1 1 1 1 Do not use washers 5 here on spring return style goal rim P N 205343A 7 97 7 o 22 Install net 38 23
3. Customer Service Center Annex 89 Larkin Ave Essendon Airport Essendon Airport North A Huffy Group WRITE IN MODEL NUMBER Portable Basketball System with Elevator Owners Manual Melbourne Australia 3041 4 SAFETY INSTRUCTIONS A FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY PROPERTY DAMAGE AND WILL VOID WARRANTY Owner must ensure that all players know and follow these rules for safe operation of the unit To ensure safety do not attempt to assemble this system without following the instructions carefully Check entire box and inside all packing material for parts Before beginning assembly read the instructions and identify parts using the hardware identifier and parts list in this document Proper and complete assembly use and supervision is essential for proper operation and to reduce the risk of accident or injury A high probability of serious injury exists if this system is not installed maintained and operated properly This equipment is intended for home recreational use only and NOT excessive competitive play Read and understand the warning label affixed to pole Label is shown on page 2 The life of your basketball pole depends on many conditions The climate placement of the pole the location of the pole exposure to corrosives such as pesticides herbicides or salts are all important During assembly if using a ladder use extreme caution Two people are recommended for this oper
4. IST Item Qty PartNo Description PartNo Description 800826 Base Gray 202808 Wheel Black 202935 Strut Holder Right Black 202936 Strut Holder Left Black 202924 Strut Holder Right Blue 202925 Strut Holder Left Blue 202878 Bolt Hex Head 3 8 16 x 8 Long 203309 Washer 3 8 I D x 1 O D 207252 Spacer 1 2 O D x 7 1 4 Long 203063 Nylon Insert Lock Nut 3 8 16 902825 Strut 1 1 4 O D x 43 Long 203157 Bolt Carriage Head 5 16 18 x 2 1 4 Long 203218 Washer 5 16 Flat 203100 Hex Flange Nut 5 16 18 202931 Collar Pole Strut Black 202922 Collar Pole Strut Blue 900873 Top Pole Black 900869 Middle amp Bottom Poles Black 202820 Rod 3 8 O D x 4 3 4 Long 202822 Eyebolt 3 8 16 x 3 3 4 Long 202821 Disk 2 3 4 Diameter 203108 Bolt Carriage Head 5 16 18 x 2 1 2 Long 900846 Board Bracket Black 201122 Bolt Hex Head 3 8 16 x 3 1 4 Long 201133 Support Bracket 201129 Spacer 1 3 4 Long 800876 Pawl amp Pin Component 201126 Release Lever 201124 Locknut Hex Head 3 8 16 240017 Bolt Hex Head 1 4 20 x 2 1 4 Long 203493 Locknut Hex Head 1 4 20 201640 Bolt Hex Head 1 2 13 x 7 1 4 Long 900843 Elevator Tube Black 201642 Spacer Plastic 201140 Wave Washer 201121 Ratchet 201646 Locknut Hex Head 1 2 13 201125 Spring 201611 Bolt Hex Flange 5 16 18 x 3 Long 203038 Carriage Bolt 5 16 18 x 2 3 4 Long Goal Rim Net 201139 Bolt Hex Head 1 2 13 x 4 1 2 Long 900867 Plate Tri
5. angle Black 201651 Spacer 1 2 I D x 1 1 8 O D x 1 4 202814 Cap Pole Top 203617 Plug Cap 204444 Black Nylon Rope 203124 Stake Tie Down POAOANWNONUiUi0NP a m AN A AB AD AA A i a PPM MND AN mm m HARDWARE IDENTIFIER Item 6 2 Item 7 3 2 _ VF Item 10 6 Item 11 12 Item 16 1 Lo JC Item 715 1 YOU MAY HAVE EXTRA PARTS WITH THIS MODEL HARDWARE IDENTIFIER CONTINUED Item 45 8 P N 205343A 7 97 10 ra HARDWARE IDENTIFIER ZZ Item 18 2 im Item 20 1 Item 26 1 Item 17 1 i A 5 2 Item 25 1 Item 27 1 HM Item 228 5 OB QE SZ FH Item 30 2 Item 31 1 Item 33 6 8777777777711 Zama Item 35 4 Item 36 2 Item 39 1 P N 205343A 7197 11 worn 183 Item 41 4
6. ation Seat the pole sections properly Failure to do so could allow the pole sections to separate during play and or transport of the system Climate corrosion and excessive use or misuse could result in pole REQUIRED TOOLS AND failure MATERIALS Check base regularly for leakage Slow leaks could cause unit to tip over Two People unexpectedly Tape Measure If technical assistance is required contact Huffy Sports Tape Adult supervision is recommended when adjusting height Wood Board Scrap am R p iza Wrenches Two 7 16 1 2 9 16 3 4 Minimum operational height is 2 m 6 6 to the bottom of backboard 9 16 Deep Socket w Ext Recommended Or Large and Small Adjustable Wrenches Most injuries are caused by misuse and or not following instructions gt LPRER Tabl U fi h ino thi it Step Ladder 8 ft 2 4 m SE CARRI Wee USMY CUS UNN Garden Hose or Sand 102 kg 225 Ib IMPORTANT Have any questions don t go back to the store We appreciate your purchasing one of our many fine products We are sure that you will be very satisfied with your selection Although great care and effort have been taken problems may occur To ensure prompt and correct handling of any problems or to answer any questions please contact the Customer Service Center Service will be quicker if you reference your Model Number found on carton PLEASE WRITE YOUR MODEL NUMBER IN THE SPACE PROVIDED ABOVE Internet Address http www huff
7. eel and strut holder in place insert spacer 6 thru notch in base strut holder 3 and wheel 2 Then push spacer thru hole in base Install bolt 4 thru washer 5 spacer 6 second washer 5 and nut 7 then tighten Repeat STEPS 1 and 2 for the opposite side P N 205343A 7 97 3 rs Setup base 1 as shown and install strut tubes 8 Line up hole in strut tube 8 with hole in strut support 3 and install hardware as shown Repeat for opposite side IMPORTANT DO NOT TIGHTEN COMPLETELY AT THIS TIME 6 Slide collar 12 onto strut tubes Line up holes in tubes 8 with holes in collar 12 Install bolt 9 thru top of collar 12 with washer 10 and nut 11 Tighten upper and lower strut hardware completely Side View P N 205343A 7197 4 d Mark poles with tape as shown IMPORTANT Bounce middle pole section onto top pole section until they no longer move toward tape reference mark Upright assembly HOLES IN TOP AND BOTTOM POLE SECTIONS MUST ALIGN TO CORRECTLY POSITION ELEVATOR SYSTEM While checking alignment add bottom pole section and bounce sections together as tight as possible Bounce sections together as tight as possible NOTE POLE SECTIONS MUST OVERLAP 8 9 CM 3 1 2 MINIMUM MIDDLE BOTTOM Spread collar 12 open and slide top of pole Install rod 15 thru holes in bottom pole section 13 through to 86 cm 34 mark on bottom pole and eyebolt 16 section 1
8. nywhere replace pole immediately Check unit before each use for loose hardware excessive wear and signs of corrosion and repair before using Check unit before each use for stability Do not use system during windy and or severe weather conditions unit may tip over Place system in the storage position and or in an area protected from the wind and free from personal property and or overhead power lines During play use extreme caution to keep player s face away from the backboard rim or net Serious injury could occur if teeth face come in contact with backboard rim or net When adjusting height unit keep hands and fingers away from moving parts Do not allow children to adjust or move unit When moving unit use caution to keep mechanism from shifting e During play do not wear jewelry rings watches necklaces etc Objects may entangle in net HEIGHT ADJUSTMENT Insert end of broom handle or wooden dowel Pa A 19 22mm diameter into release lever A Vy Push up pivot outward to raise and lower HUFFY SPO RTS In the U S 1 800 558 5234 and Canada Only 1 800 284 8339 206113 5 97 P N 205343A 7197 2 d 1 Lay base 1 bottom up and set wheel 2 into place gt Slide strut holder 3 between wheel 2 and base 1 NOTE Wheel 1 has spacer snapped in place over axle hole the spacer should face the strut holder 3 Bottom View of Base 3 With wh
9. ysports com Toll Free Customer Service Number for Austrailia 1 800 333061 P N 205343A 7197 1 d IMPORTANT WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1 OF THIS OWNERS MANUAL AWARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE Owner must ensure that all players know and follow these rules for safe operation of the unit See instruction manual for proper installation and maintenance Use caution when performing dunk type activities on this unit Do not hang from any part of unit including backboard support braces rim or net Do not slide climb shake or play on base and or pole Surface beneath the base must be smooth and free of gravel or other sharp objects Punctures cause leakage and could cause unit to tip over After assembly is complete fill system completely with water or sand and stake to the ground Never leave unit in an upright position without filling base with weight as unit may tip over causing injury Do not allow water in base to freeze During sub freezing weather add non toxic antifreeze sand or empty base completely and store Do Not Use Salt Keep pole top covered with cap at all times Keep organic material away from pole base Grass litter etc could cause corrosion and or deterioration Check pole system for signs of corrosion rust pitting chipping and repaint with exterior enamel paint If rust has penetrated through steel a
Download Pdf Manuals
Related Search