Huffy NT9110 User's Manual
Contents
1. V Customer Service EH N53 W24700 South Corporate Circle Sussex WI 53089 U S A A Huffy Sports Company WRITE IN YOUR MODEL NUMBER Portable Basketball System Owners Manual NOTICE TO ASSEMBLERS A SAFETY INSTR U CTIONS A ALL Huffy Sports basketball Systems including those used for DISPLAYS MUST be assembled and ballasted with sand or water according to instructions Failure to follow instructions could result in SERIOUS INJURY It is FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY NOT acceptable to devise a makeshift weight RESULT IN SERIOUS INJURY system PROPERTY DAMAGE AND WILL VOID WARRANTY Owner must ensure that all players know and follow these rules for safe operation of the unit To ensure safety do not attempt to assemble this system without following the instructions carefully Check entire pallet and inside all packing material for parts Before beginning assembly read the instructions and identify parts using the hardware identifier and parts list in this document Proper and complete assembly use and supervision are essential for proper operation and to reduce the risk of accident or injury A high probability of serious injury exists if this system is not installed maintained and operated properly This equipment is intended for home recreational use only and NOT excessive competitive play Read and understand the warning label affixed to pole Label is shown on page 2 The lif2. Bracket Orange 920038 Inner Bracket Black 220065 Bolt Carriage 3 8 x 5 1 2 220064 Spacer 5 x 1 2 O D 203439 Bolt Hex 3 8 16 x 6 203017 Nut Hex 3 8 16 Gi Qi Qi a a FAH ak and PhP po HARDWARE IDENTIFIER Item 6 5 Item 7 5 Item 8 5 Item 9 16 Item 10 16 Item 14 4 Item 15 10 Item 19 1 Item 18 1 Item 21 2 P N 211550A 07 01 14 3 HARDWARE IDENTIFIER mm Ob Item 24 2 Item 25 2 Item EL 7 Item 29 1 Item 28 2 Item 30 4 Item 35 1 Item 36 4 O QE Item 42 1 Item 27 1 Item 31 4 Item 39 1 Item 40 1 Item 41 1 fei 15 07 01 211550
3. e of your basketball pole depends on many conditions The climate placement of unit the location of unit exposure to corrosives such as pesticides herbicides or salts are all important During assembly if using a ladder use extreme caution Two people are REQUIRED TOOLS AND recommended for this operation MATERIALS Climate corrosion and excessive use or misuse could result in pole TWO Paople failure Carpenters Level Wrench 3 4 Or Small Adjustable If technical assistance is required contact Customer Service Center Combination Wrenches Two 1 2 9 16 Adult supervision is recommended when adjusting unit Step Ladder 8 ft 2 4 m Minimum operational height is 6 6 2 m to the bottom of backboard Utility Knife Reversible Drill with 3 Phillips and Standard ne EE Screwdriver Tips Most injuries are caused by misuse and or not following instructions Ballast Sand or Dry Cement Use caution when using this unit 480 640 165 218 290 IMPORTANT Have questions Don t go back to the store We appreciate your purchasing one of our many fine products We are sure that you will be very satisfied with your selection Although great care and effort have been taken occasionally problems may occur To ensure prompt and correct handling of any problems or to answer any questions please contact our Toll Free Customer Service Number listed below Service will be quicker if you have your Model Number found on carton and as
4. en completely AWARNING WHEN HEIGHT HAS BEEN ADJUSTED MAKE SURE THAT HANDLE IS COMPLETLEY TIGHTENED P N 211550A 07 01 12 a Ground Installation Place unit in desired location Secure unit to ground or flat surface as shown FLOOR SCREW NOT INCLUDED Regulation Rim Height is 10 Feet 3 05 m 13 07 01 P N 211550A PARTS LIST Qty Part Description Qty Part No Description 206597 Pad Lower Front 206592 Shroud Right Cover 206593 Shroud Left Cover 206574 Extension Arm 206556 Flat Wrench 206572 Bolt Slotted Pan Head 1 4 20 206143 Washer Locking 1 4 201114 Washer Flat 1 4 203415 Screw Php Head 10 x 1 206151 Fender Washer 1 O D 920263 Rim Orange 206591 Foam Padding 984001 Backboard 201611 Bolt Hex Flange 5 16 18 x 3 203218 Washer Flat 5 16 203100 Nut Hex Flange 5 16 18 200484 Spring 220043 Washer Concave 201124 Nut Hex Locking 5 16 18 960043 Cover Plate Orange 220140 Screw Tap 1 4 x 3 4 206567 Backboard Struts 206585 L Bracket 203153 Bolt Hex 5 16 18 x 3 4 206116 Lockwasher Split 5 16 203001 Nut Hex 5 16 18 203474 Washer Flat 1 2 x 1 O D 205220 Weld Studs 200514 Bolt Hex 3 8 16 x 3 203335 Washer 3 8 x 1 O D 203063 Lock Nut 3 8 16 Nylon Insert 204282 Net 206557 Tie Down Bracket 203124 Tie Down Stake 206252 Bolt Hex 3 8 16 x 1 203032 Washer Flat 920262
5. lity Do not use system during windy and or severe weather conditions unit may tip over Place system in the storage position and or in an area protected from the wind and free from personal property and or overhead power lines During play use extreme caution to keep player s face away from the backboard rim or net When adjusting height or moving unit keep hands and fingers away from moving parts Do not allow children to move or adjust unit During play do not wear jewelry rings watches necklaces etc Objects may entangle in net In the U S 1 800 558 5234 211411 1 98 IMPORTANT WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1 OF THIS OWNERS MANUAL Use a fork lift to remove unit from truck and carefully remove packing materials 2 Remove backboard lower pad 1 and both shroud covers 2 and 3 IMPORTANT DO NOT REMOVE STABILIZING STRAP AT THE REAR OF MAIN POST AT THIS TIME Remove the three screws which hold base to pallet and carefully lay unit base forward down to floor Discard screws TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY 07 01 P N 211550A Ballast Installation Remove extension arm 4 from slide post brackets as shown IMPORTANT SET BRAKE AT THIS TIME 5 Cut stabilizing strap and set brake so unit will not roll mas Raise main post upward into playing p
6. n Refer to Step 4 AWARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY Lift backboard upward at an inclined angle and position slip pin into slot as shown for unfolding AWARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY FOR STORAGE Position Slip Pin Here P N 211550A 07 01 uidi AUN ZZ TO UNFOLD Position Slip Pin Here Re tighten nut located at top of post behind mast Refer to Step 7 Raise pole mast into playing position Remove bolt at end of post brackets Rotate extension arm and up into playing position and re insert bolt to secure fei 07 01 211550 Height Adjustment AWARN NG 27 Remove tagged bolt at top of slide post DO NOT UNFOLD UNIT IF ELEVATED MAY RESULT IN DAMAGE TO THE UNIT AWARNING RE INSERT TAGGED BOLT FOR STORAGE FAILURE TO DO SO MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE AWARNING DO NOT PLACE HANDS IN ZX FRONT OF THE MAIN POST SUPPORTS IN MOTION MAY gt RESULT IN BODILY INJURY NOTE Rotate hand cranking bolt to loosen and tighten Stand to the side of unit with both hands securely on height adjustment handle Carefully slide pole mast upward to desired height Then turn cranking bolt to tight
7. osition W Tighten nut located at top of pole behind mast Flat wrench 5 included P N 211550A 07 01 4 Attach lower front pad 1 to unit as shown DO NOT USE UNIT WITHOUT BALLAST MAY TIP OVER UST 80 LB 36 KG p ff BALLAST Su Install 640 lbs 290 kg of ballast Secure y 80 LB 36 KG with straps NOTE Equal weight on each side A Jf 87 1457 required 80 6 KG 80 LB 36 871 8018 a os O Install shroud cover 3 as shown Repeat for opposite side fei 5 07 01 211550 11 Install carriage bolt 39 through rim 11 washers 27 and 36 as shown Tighten nut 42 completely Place nylon lock nut 31 about half way up carriage bolt 39 as shown 12 Attach bracket 37 to backboard and support structure by inserting bolts 14 through washers 15 and top holes in bracket 37 Tighten nuts 16 completely Peel and stick foam pad 12 to front of board behind bracket Insert inner bracket 38 into bracket 37 as shown Insert bolts 14 through washers 15 and top holes of inner bracket 38 as shown Tighten nuts 16 completely P N 211550A 07 01 6 Insert spacer 40 through rim assembly 11 Place rim assembly on bracket 37 so the cariage bol
8. sembly instructions ready when calling PLEASE WRITE YOUR MODEL NUMBER IN THE SPACE PROVIDED ABOVE Toll Free Customer Service Number for U S 1 800 558 5234 Canada Only 1 800 284 8339 Internet Address http www hydra rib com 84 printed on recycled paper 1 07 01 P N 211550A P N 211550A 07 01 AWARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE Owner must ensure that all players know and follow these rules for safe operation of the unit See instruction manual for proper installation and maintenance Use caution when performing dunk type activities on this unit Do not hang from any part of unit including backboard support braces rim or net Do not slide climb or play on base and or pole Surface beneath the base must be smooth and free of gravel After assembly is complete distribute ballast and stake to the ground Never leave unit in an upright position without placing required amount of ballast in base as unit may tip over causing injury Keep organic material away from base Grass litter etc could cause corrosion and or deterioration Check pole system for signs of corrosion rust pitting chipping and repaint with exterior enamel paint If rust has penetrated through steel anywhere replace pole immediately Check unit before each use for loose hardware excessive wear and signs of corrosion and repair before using Check unit before each use for stabi
9. t 39 is inserted through hole on top of inner bracket 38 Install bolt 41 washers 36 and nut 31 through top holes on bracket 37 as shown Tighten completely BOTTOM VIEW 15 Install rubber grommet 17 concave washer 18 and center lock nut 19 to bolt 89 as shown aS j 9 2 Do not over tighten as rim will not flex properly See leveling instructions to determine how much to tighten nuts 19 and 39 fei 7 07 01 211550 16 RIM LEVELING INSTRUCTIONS Place level on rim 11 and adjust nut 31 until level Tighten nut 42 to set rim tension for playing 17 Install cover plate 20 on rim 11 using self tapping screws 21 as shown NOTE ORIENTATION OF COVER PLATE P N 211550A 07 01 8 9 Loosely assemble hardware to strut 22 Mount strut 22 to backboard and finger tighten Repeat for opposite side Secure struts 22 to extension arm 4 Completely tighten all strut hardware in Step 15 and Step 16 fei 9 07 01 211550 Q1 Loosen nut located at top of post behind pole mast Refer to Steps 6 and 7 and carefully lower pole mast as shown Insert extension arm and backboard assembly into place and secure as show
Download Pdf Manuals
Related Search