Huffy M731321 User's Manual
Contents
1. replace pole immediately Check system before each use for proper ballast loose hardware excessive wear and signs corrosion and repair before use Check system before each use for instability Do not use system during windy and or severe weather conditions system may tip over Place system in the storage position and or in an area protected from the wind and free from personal property and or overhead wires Never play on damaged equipment See instruction manual for proper installation and maintenance When moving system use caution to keep mechanism from shifting Keep pole top covered with cap at all times Do not allow water in tank to freeze During sub freezing weather add 2 gallons of non toxic antifreeze sand or empty tank completely and store Do not use salt While moving system do not allow anyone to stand or sit on base or have added ballasting on base Do not leave system unsupervised or play on system when wheels are engaged for moving Use Caution when moving system across uneven surfaces System may tip over Use extreme caution if placing system on sloped surface System may tip over more easily SPALDING HYDRA RIB In the U S 1 800 In the U S 1 800 Canada 1 800 200 2000 dm Canada 1 800 200 2000 FUSSELL BATHLETIC HUFFY SPORTS In the U S 1 800 xxx 200 In the U S 1 800200 00xx Canada 1 800 cod 108 556790 01 05 SAFETY INSTRUCT2. with carriage bolts 28 in lower pole mounting holes as shown Tighten flange nuts 16 completely M731321 11 05 14 SECTION B ATTACH THE BACKBOARD This is what your system will look like when you ve finished this section 2 1 2 AND 2 9 16 AND 2 3 4 Wrenches AND OR 2 Socket Wrenches and Sockets 1 2 9 16 3 4 15 11 05 ID M731321 Assemble backboard brackets 29 using bolts 35 and nuts 9 as shown IMPORTANT Test fit bolts into holes of brackets and carefully rock them in a circular motion to ream out paint from holes if necessary NOTE ORIENTATION o Identify elevator tubes 41 and 44 O Upper Elevator tube Toward Pole Toward Board Lower Elevator tube M731321 11 05 16 Attach lower elevator tubes 41 to backboard brackets 29 using spacers 42 bolt 22 and nut 21 as shown Insert T bolt 86 through Slam Jam bracket 32 as shown Secure Slam Jam bracket 32 and backboard bracket 29 assemblies to backboard Use bolt 15 and nut 16 as shown TWO PEOPLE REQUIRED FOR THIS PROCEDURE FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE Test fit bolts into holes of brackets and carefully rock them in a circular motion to ream out paint from holes if necessary 17 11 05 ID M731321 Attach upper elevator tubes 44 to backboard support brackets 29 usin
3. 05 Read and understand warnings listed below before using this product Failure to follow these warnings may result in serious injury and or property damage Owner must ensure that all players know and follow these rules for safe operation of the system DO NOT HANG on the rim or any part of the system including backboard support braces or net During play especially when performing dunk type activities keep player s face away from the backboard rim and net Serious injury could occur if teeth face come in contact with backboard rim or net Do not slide climb shake or play on base and or pole After assembly is complete fill system completely with water or sand and stake to the ground Never leave system in an upright position without filling base with weight as system may tip over causing injuries When adjusting height or moving system keep hands and fingers away from moving parts Do not allow children to move or adjust system During play do not wear jewelry rings watches necklaces etc Objects may entangle in net Surface beneath the base must be smooth and free of gravel or other sharp objects Punctures cause leakage and could cause system to tip over Keep organic material away from pole base Grass litter etc could cause corrosion and or deterioration Check pole system for signs of corrosion rust pitting chipping and repaint with exterior enamel paint If rust has penetrated through the steel anywhere
4. basketball pole depends on many conditions The climate placement of the pole location of the pole exposure to corrosives such as pesticides herbicides or salts are all important If technical assistance is required contact Huffy Sports Adult supervision is recommended when adjusting height Most injuries are caused by misuse and or not following instructions Use caution when using this system A Pull Trigger Move up or down to desired height Release trigger to lock at desired height Adjust basketball backboard height to lowest position While holding pole rotate basketball system forward until wheels engage with ground Move basketball system to desired location Carefully rotate basketball system upright Reattach ground restraint and check system for stability 211262 06 00 3 11 05 ID M731321 Questions or Missing Parts DON T go back to store Call TOLL FREE Customer Service Number listed on the front page IMPORTANT Remove all contents from boxes Be sure to check inside pole sections hardware and additional parts are packed inside NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems including those used for DISPLAYS MUST be assembled and ballasted with sand or water according to the instructions Failure to follow instructions could result in SERIOUS INJURY It is NOT acceptable to devise a makeshift weight system ID M731321 WARRANTY CARD P
5. x 1 75 Long 2 203617 Plug Cap 1 211262 Label Height Adjustment and Moving 1 Net 1 200209 Pole Mount Bracket 2 203231 Bolt Carriage 5 16 18 x 3 5 Long 2 90096401 Backboard Bracket 1 1 1 1 1 4 1 1 1 2 1 2 4 1 2 1 1 1 1 1 1 2 1 203472 Spring Black Slam Jam 200318 Bracket Reinforcement Slam Jam 900033 Bracket Slam Jam 200212 Trigger 206990 Reinforcement Bracket 204961 Bolt Hex 3 8 16 x 625 Long 203796 T Bolt 3 8 16 x 5 Long 204872 Labels Height Indicator 203470 Washer Flat Slam Jam 203678 Bolt Hex 3 8 16 x 6 5 Long 203795 Nut Special Slam Jam 902537 Lower Elevator Tubes 201642 Spacer 530 I D x 5 O D x 63 Long 204838 Spring Elevator 900184 Upper Elevator Tubes 200215 Cross Pin 200214 Locking Pin 200211 Left Handle 200210 Right Handle 900006 Adjustment Tube Upper 200257 Spring 202862 Spacer 563 I D x 1 19 Long 908109 Adjustment Rod Lower Hardware kit is designed for more than one style of basketball system Not all hardware will be used You may have extra parts with this model ID 731321 11 05 6 HARDWARE IDENTIFIER BOLTS AND SCREWS Om Mmm E rn 28 2 35 4 Item 11 1 Item 23 1 Item 22 5 HARDWARE IDENTIFIER NUTS AND WASHERS onli Item 16 8 Item 13 2 Item 12 6 Item 38 1 Ite tem 9 TT sey Item 21 5 7 11 05 I
6. 5 11 05 ID M731321 Q Install net 26 as shown Lock elevator system into highest position so the backboard is as high as it will go Apply 10 ft height indication sticker 37 to adjustment rod 52 directly below arrow on handle as shown Move elevator system to the next position and apply the 91 2 ft sticker Repeat until all height settings have been labeled 8 10 ft ID M731321 11 05 26 Roll completed assembly to desired position Fill tank with water approx 30 gallons 115 Liters or sand approx 300 16 136 kg and snap cap 24 in place TWO PEOPLE REQUIRED FOR THIS PROCEDURE FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY IT MAY TIP OVER CAUTION ADD TWO GALLONS 7 6 LITERS OF NON TOXIC ANTIFREEZE IN SUB FREEZING CLIMATES IF USING SAND 2 GALLONS OF ANTI FREEZE 15 NOT REQUIRED Peel protective film from surface of acrylic backboard prior to use 27 11 05 ID M731321 Pull trigger 33 Move elevator system up or down to desired height release trigger 33 to lock system into one of the five height settings DO NOT ALLOW CHILDREN TO ADJUST HEIGHT M731321 11 05 28
7. D M731321 HARDWARE IDENTIFIER STEEL SPACERS OL o 10 Item 45 1 Item 42 4 Item 46 1 HARDWARE IDENTIFIER PLASTIC SPACERS CAPS CLIPS AND OTHER o ONE Item 47 1 teint Item 51 2 5 Item 36 1 os Item 40 1 Item 17 2 Item 32 1 Item 31 1 Item 30 1 M731321 11 05 8 SECTION A ASSEMBLE THE BASE 2 1 2 and 2 9 16 Wrenches AND OR This is what your system will look like when you ve finished this section 2 Socket Wrenches and Sockets 12 9 16 Correctly identify each pole section Poles have an identification sticker that will be used as a reference point in the next step Identification Sticker 9 13 cm BOTTOM 9 11 05 ID M731321 While maintaining alignment bounce pole top 4 and middle section 5 together as shown until they no longer move toward identification sticker Upright assembly CAUTION THE IDENTIFICATION STICKER IS LOCATED 5 FROM THE END OF THE POLE WHEN PROPERLY POUNDED TOGETHER THE POLE SECTIONS SHOULD HAVE A 3 1 2 MINIMUM OVERLAP LEAVING 1 1 2 BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER IMPORTANT Align dimple of top pole section 4 into trough of middle pole section 5 as shown ID STICKER M731321 11 05 10 While maintaining alignment bounce assembly and bottom pole section 6 together as shown until they no longer move toward identi
8. IONS A FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY Owner must ensure that all players know and follow these rules for safe operation of the system To ensure safety do not attempt to assemble this system without following the instructions carefully Check entire box and inside all packing material for parts and or additional instruction material Before beginning assembly read the instructions and identify parts using the hardware identifier and parts list in this document Proper and complete assembly use and supervision are essential for proper operation and to reduce the risk of accident or injury A high probability of serious injury exists if this system is not installed maintained and operated properly If using a ladder during assembly use extreme caution Two 2 people are recommended for this operation Check base regularly for leakage Slow leaks could cause system to tip over unexpectedly Seat the pole sections properly if applicable Failure to do so could allow the pole sections to separate during play and or transport of the system Climate corrosion or misuse could result in system failure Minimum operational height is 6 6 1 98 m to the bottom of backboard This equipment is intended for home recreational use only and NOT excessive competitive play Read and understand the warning label affixed to pole The life of your
9. REQUIRED TOOLS Pedir ortable System m Owners Manual Customer Service Center e Tape Measure N53 W24700 South Corporate Circle Sussex WI 53089 U S A Wood Board scrap Sawhorse or Support Table Safety Glasses Step Ladder 8ft 2 4 m 2 or 3 Phillips Screwdriver j 2 each Wrenches and or Socket Wrenches and Sockets Deep Well Sockets are Recommended Extension is Recommended 12 9 16 3 4 AND OR aro 1 2 9 16 3 4 Garden Hose or Sand Write Model Number READ AND UNDERSTAND From Box Here OPERATOR S MANUAL BEFORE USING THIS UNIT FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY Toll Free Customer Service Number for U S 1 800 558 5234 For Canada 1 800 284 8339 For Europe 00 800 555 85234 Sweden 009 555 85234 Large and Small Adjustable For Australia 1 800 632 7921 Wrenches Internet Address http www huffysports com 1 11 05 ID M731321 COPYRIGHT 2005 by SPALDING BEFORE YOU START To ensure optimal playability of backboard system a close tolerance fit between the elevator components and hardware is required Test fit large bolts into large holes of elevator tubes backboard brackets and triangle plates Carefully rock them in a circular motion to ream out any excess paint from holes if necessary Not all items pictured are included with every model ID M731321 11
10. fication sticker CAUTION THE IDENTIFICATION STICKER IS LOCATED 5 FROM THE END OF THE POLE WHEN PROPERLY POUNDED TOGETHER THE POLE SECTIONS SHOULD HAVE A 3 1 2 MINIMUM OVERLAP LEAVING 1 1 2 BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER IMPORTANT Align dimple of middle pole section 5 into trough of bottom pole section 6 as shown Bottom pole 11 11 05 ID M731321 Install rod 7 through holes in bottom pole section 6 and eyebolt 8 Install wheel axle 2 through wheel carriage 19 and install wheels 3 onto wheel axle 2 with spacers 17 as shown Insert pole assembly into tank assembly as shown Secure bottom pole 6 section to tank and wheel carriage as shown A deep socket is recommended Nec IMPORTANT DO NOT OVER TWO PEOPLE REQUIRED TIGHTEN FOR THIS PROCEDURE FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE THE SPACER 17 WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE IMPORTANT The Warning Label should be facing towards the front ID M731321 11 05 12 Secure flat end of tank struts 10 to pole using bolt 11 washers 12 and nut 13 as shown Rotate the non secured angled ends of the struts 10 as shown Secure tank struts 10 to the base using bolt 15 washers 12 and nut 16 13 11 05 ID M731321 Install pole mount bracket 27 and reinforcement bracket 34
11. g spacers 42 bolt 22 and nut 21 as shown M731321 11 05 18 Q Support pole on sawhorse Attach upper and lower elevator tubes 41 and 44 to upper pole section 4 using bolts 22 and nuts 21 as shown Attach pole cap 14 as shown TWO PEOPLE REQUIRED FOR THIS PROCEDURE FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE 19 11 05 ID M731321 Insert locking pin 46 into bracket on adjustment tube 49 Insert cross pin 45 through hole in bracket and locking pin 46 as shown in figure A Fit left handle 47 onto adjustment tube 49 so the bottom of adjustment tube 49 sits on the two small ribs of the handle as shown in figure B M731321 11 05 20 Insert spring 50 into back of locking pin 46 as shown Spring 50 should rest between two small rips at the back of the plastic handle as shown in Figure C Insert top of trigger 33 into bracket on the adjustment tube 49 as shown The plastic post of the handle pieces should go through the hole in bottom of trigger 33 and hold it into place as shown 21 11 05 ID M731321 Finish handle assembly by attaching right handle 48 using screws 18 as shown o Attach adjustment tube 49 to lower elevator tubes 41 using bolt 22 spacers 51 and nut 21 as shown ID M731321 11 05 22 Insert lower adjustment rod 52 into bottom of adjustment tube 49 pull t
12. lease remember to complete your product registration form either on line at www huffysports com customer_support product_registration or mail in the enclosed postcard WARNING IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC BACKBOARD EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY HAVE OCCURRED DURING SHIPMENT CRACKS IN THE BACKBOARD COULD RESULT IN SUDDEN BREAKAGE IF BACKBOARD IS DAMAGED IN ANY WAY PRIOR TO OR AFTER ASSEMBLY CALL TOLL FREE NUMBER U S 1 800 558 5234 CANADA 1 800 284 8339 http www huffysports com 11 05 4 Get to know the basic parts of your basketball system FRONT VIEW BACKBOARD ELEVATOR ADJUSTMENT 5 11 05 ID M731321 PARTS LIST See Hardware Identifier Qty Part No Description 1 206657 Tank Black 1 200628 Wheel Axle 2 226401 Wheel 4 Black 1 90021701 Top Pole Section 1 904840 Middle Pole Section 1 900136 Bottom Pole Section 1 202820 Rod 3 8 O D x 4 3 4 Long 1 202822 Eyebolt 3 8 16 x 2 1 2 Long 7 203063 Nylon Insert Lock Nut 3 8 16 2 906206 Tank Strut 1 201625 Bolt Yellow Dichromate 5 16 18 X 3 60 Long 6 203218 Washer Flat 3 8 I D 2 203099 Nylon Insert Lock Nut 5 16 18 1 206219 Cap Pole Top 3 6 205528 Bolt Hex Flange 5 16 18 x 1 Long 8 203100 Nut Hex Flange 5 16 18 2 201651 Spacer 500 I D x 25 Long 5 204804 Screw Phillips Head 3 4 Long 1 200627 Wheel Bracket 1 Rim 5 206340 Nut 1 2 13 5 206304 Bolt 1 2 13 x 6 5 16 Long 1 202739 Bolt 5 16 18
13. rigger to allow lower adjustment rod to move about mid way into adjustment tube 49 release the trigger so the lower adjustment rod 52 locks into position midway inside the adjustment tube 49 Attach the lower adjustment rod 52 to elevator bracket 27 using bolt 23 and nut 13 as shown DO NOT LEAVE TWO PEOPLE REQUIRED ASSEMBLY FOR THIS PROCEDURE FAILURE TO FOLLOW THIS TE WARNING COULD RESULT IN OVER SERIOUS INJURY AND OR i PROPERTY DAMAGE 23 11 05 ID M731321 Q Install Slam Jam Rim to Backboard A Fit rim 20 securely into bracket 32 as shown Allow T bolt 36 to slip through center hole in rim 20 B Install reinforcement bracket 31 onto T bolt 36 as shown C Install spring 30 onto T bolt 36 as shown D Install special nut 40 and washer 38 onto T bolt 36 E Tighten nut 40 until flush with end of T bolt 36 ID M731321 11 05 24 Support system on sawhorse Extend system to highest position before assembly of spring Attach counterbalance spring 43 to upper elevator tubes with bolt 39 and nut 9 in location shown Stretch spring to lower elevator tubes and attach with hardware as shown TWO PEOPLE REQUIRED F USE EYE PROTECTION FOR THIS PROCEDURE WHEN INSTALLING FAILURE TO FOLLOW THIS SPRINGS WARNING COULD RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE 2
Download Pdf Manuals
Related Search