HP 3500ca Maintenance and Service Guide
Contents
1. Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove the back cover see Back cover on page 18 HP Slate10 HD 19 Remove the sensor module 1 Turn the back cover upside down with the bottom edge toward you 2 Detach the sensor module 1 from the back cover The sensor module is attached to the back cover with double sided adhesive 3 Remove the sensor module 2 Reverse this procedure to install the sensor module Battery Description Spare part number Battery 3 7 V 7000 mAh 25 9 WHr LI includes cable 743896 001 Before removing the battery follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet 3 Disconnect all external devices from the tablet 4 Remove the back cover see Back cover on page 18 Z WARNING To reduce potential safety issues use only the battery provided with the tablet a replacement battery provided by HP or a compatible battery purchased from HP 20 Chapter 5 Removal and replacement procedures Z CAUTION Removing a battery that is the sole power source for the tablet can cause loss of information To prevent loss of information save your work or shut down the tablet through Wind2. 240 V 50 60 Hz NOTE The tablet can operate on DC power using an industry standard micro A or micro B USB cable The HP 5V 2A adapter included with your tablet is recommended for charging the tablet Temperature Operating 5 C to 35 C 41 F to 95 F Nonoperating 20 C to 60 C 4 F to 140 F Relative humidity non condensing Operating 10 to 90 Nonoperating 5 to 95 Maximum altitude unpressurized Operating 15 m to 3 048 m 50 ft to 10 000 ft Nonoperating 15 m to 12 192 m 50 ft to 40 000 ft NOTE Applicable product safety standards specify thermal limits for plastic surfaces The device operates well within this range of temperatures HP Slate10 HD 51 HP Slate7 HD 52 Metric U S Dimensions Width 20 13 cm 7 93 in Depth 0 99 cm 0 39 in Height 11 98 cm 4 72 in Weight 0 33 kg 0 72 lb Input power The tablet operates on DC power which can be supplied by an AC or a DC power source The AC power source must be rated at 100 240 V 50 60 Hz NOTE The tablet can operate on DC power using an industry standard micro A or micro B USB cable The HP 5V 2A adapter included with your tablet is recommended for charging the tablet Temperature Operating 5 C to 35 C 41 F to 95 F Nonoperating 20 C to 60 C 4 F to 140 F Relative humidity non condensing Operating 10 to 90 Nonoperating 5 to 95 Maximum altitude unpressurized Operating
3. 42 Chapter 5 Removal and replacement procedures System board Description Spare part number Equipped with a Marvel PXA986 1 20 GHz dual core SOC processor 1 0 GB system memory a 743049 001 16 GB eMMC solid state drive and WiFi capability Before removing the system board follow these steps Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove the back cover see Back cover on page 37 uo B Q N Disconnect the battery cable from the system board see Battery on page 38 HP Slate7 HD 43 Remove the system board 1 Disconnect the following cables from the system board 1 Rear facing webcamera cable 2 Front facing webcamera cable 3 Power button microphone module cable 4 Volume button board cable 5 Display panel cable ZIF connector and cable 44 Chapter 5 Removal and replacement procedures 2 3 Disconnect the following cables from the system board 1 USB board ZIF connector and cable 2 Speaker cable 3 TouchScreen module cable Remove the following screws that secure the system board to the display panel assembly 1 One Phillips PM1 4x4 1 screw 2 Two Phillips PM2 0x3 5 screws 3 Three Phillips PM2 0x2 75 screws HP Slate
4. see Back cover on page 18 5 Disconnect the battery cable from the system board see Battery on page 20 Remove the microphone 1 Release the ZIF connector 1 to which the microphone cable is attached and then disconnect the microphone cable from the system board 2 Detach the microphone 2 from the display panel assembly The microphone is attached to the display panel assembly with double sided adhesive 3 Remove the microphone and cable Reverse this procedure to install the microphone HP Slate10 HD 25 Rear facing webcamera Description Spare part number Rear facing webcamera includes cable 744545 001 Before removing the rear facing webcamera follow these steps 1 2 3 4 5 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove the back cover see Back cover on page 18 Disconnect the battery cable from the system board see Battery on page 20 Remove the rear facing webcamera 1 2 3 Disconnect the rear facing webcamera cable 1 from the system board Detach the rear facing webcamera 2 from the display panel assembly The rear facing webcamera is attached to the display panel assembly with double sided adhesive Remov
5. Safety warning notice ZN WARNING To reduce the possibility of heat related injuries or of overheating the device do not place the device directly on your lap or obstruct the device air vents Use the device only on a hard flat surface Do not allow another hard surface such as an adjoining optional printer or a soft surface such as pillows or rugs or clothing to block airflow Also do not allow the AC adapter to contact the skin or a soft surface such as pillows or rugs or clothing during operation The device and the AC adapter comply with the user accessible surface temperature limits defined by the International Standard for Safety of Information Technology Equipment IEC 60950 iv Safety warning notice Table of contents 1 Product description A A A 1 2 External component identification e eerie estet rete hei to t tito rar rr EFE AE ERE PARE RO arras FERRI RARUS 4 puc TO 10 eH EI TEE 4 HP Slate7 HD NEP 5 3 Wusiroared paris calaleg uuscassncacoMchbbpsos CF pietra RC EM RB V n E DU ad DE DIN P PP MK MPG DEPO MI POL LM FAMEM EI MEE dE 6 Locating the serial number product number and model number ooooococccoccccccoooccccononccnonnnnnconno nono 6 HP Slate 10 HD tablet major components iia 7 HP Slate HD tablet major components elote red 9 NAT ce EO Pa aaa 10 Sequential part number listing rin canada 11 4 Removal and replacement preliminary requirements s ssssoseosesessco
6. board cable 3 from the display panel assembly The USB board cable is attached to the display panel assembly with double sided adhesive 4 Remove the two Phillips PM2 0x2 0 broad head screws 4 that secure the USB board to the display panel assembly 5 Remove the USB board bracket 5 and the USB board 6 iw T Oc cs cs es om en a i 7 o JF Reverse this procedure to install the USB board HP Slate10 HD 31 System board Ex NOTE The system board spare part kit is equipped with a Marvel PXA986 1 20 GHz dual core SOC processor 1 0 GB system memory and a 16 GB eMMC solid state drive Description Spare part number Equipped with WWAN capability 744058 001 Equipped with WiFi capability 744057 001 Before removing the system board follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet 3 Disconnect all external devices from the tablet 4 Remove the back cover see Back cover on page 18 5 Disconnect the battery cable from the system board see Battery on page 20 32 Chapter 5 Removal and replacement procedures Remove the system board 1 Disconnect the following cables from the system board 1 Left speaker cable 2 Power button board ZIF connector and cable 3 Volume
7. button board ZIF connector and cable 4 TouchScreen module ZIF connector and cable 5 USB board ZIF connector and cable 6 Display panel cable ZIF connector and cable HP Slate10 HD 33 2 Disconnect the following cables from the system board 1 Microphone ZIF connector and cable 2 Rear facing webcamera cable 3 Card reader board ZIF connector and cable 4 Right speaker cable 3 Remove the three Phillips PM2 0x2 75 screws 1 and the three Phillips PM2 0x2 0 broad head screws 2 that secure the system board to the display panel assembly 34 Chapter 5 Removal and replacement procedures 4 Remove the system board 3 EX m Reverse this procedure to install the system board Front facing webcamera Description Spare part number Front facing webcamera includes cable 744544 001 Before removing the front facing webcamera follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet 3 Disconnect all external devices from the tablet 4 Remove the back cover see Back cover on page 18 5 Disconnect the battery cable from the system board see Battery on page 20 6 Remove the system board see System board on page 32 HP Slate10 HD 35 36 Remove the front facing webc
8. facing webcamera Description Spare part number Front facing webcamera includes cable 743050 001 Before removing the front facing webcamera follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet HP Slate7 HD 49 3 Disconnect all external devices from the tablet 4 Remove the back cover see Back cover on page 37 and then remove the following components a Battery see Battery on page 38 b System board see System board on page 43 c 3G antenna module see Antenna modules on page 46 Remove the front facing webcamera 1 Turn the 3G antenna module upside down with the bottom toward you 2 Release the front facing webcamera from the retention molding built into the 3G antenna module e 3 Remove the frontfacing webcamera and cable Reverse this procedure to install the frontfacing webcamera 50 Chapter 5 Removal and replacement procedures 6 Specifications HP Slate10 HD Metric U S Dimensions Width 17 80 cm 7 01 in Depth 0 97 cm 0 38 in Height 25 90 cm 10 19 in Weight lowest weight configuration 0 63 kg 1 38 lb Input power The tablet operates on DC power which can be supplied by an AC or a DC power source The AC power source must be rated at 100
9. for specific countries and regions Country region Accredited agency Applicable note number Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Requirements for all countries 53 54 Country region Accredited agency Applicable note number Germany VDE Italy IMQ 1 Japan METI 3 The Netherlands KEMA 1 Norway NEMKO 1 The People s Republic of China coc 5 South Korea EK 4 Sweden CEMKO 1 Switzerland SEV 1 Taiwan BSMI 4 The United Kingdom BSI 1 The United States UL 2 1 The flexible cord must be Type HO5VV F 3 conductor 1 0 mm conductor size Power cord set fittings appliance coupler and wall plug must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used The flexible cord must be Type SPT 3 or equivalent No 18 AWG 3 conductor The wall plug must be a two pole grounding type with a NEMA 5 15P 15 A 125 V or NEMA 6 15P 15 A 250 V configuration The appliance coupler flexible cord and wall plug must bear a T mark and registration number in accordance with the Japanese Dentori Law The flexible cord must be Type VCT or VCTF 3 conductor 1 00 mm conductor size The wall plug must be a two pole grounding type with a Japanese Industrial Standard C8303 7 A 125 V configuration The flexible cord must be Type RVV 3 conductor 0 75 mm conductor size Power
10. includes cable double sided adhesive and rubber pad 744538 001 Before removing the power button board follow these steps 1 POP Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove the back cover see Back cover on page 18 Disconnect the battery cable from the system board see Battery on page 20 22 Chapter 5 Removal and replacement procedures Remove the power button board 1 Remove the rubber pad 1 that protects the power button board cable ZIF connector 2 Release the ZIF connector 2 to which the power button board cable is attached and then disconnect the power button board cable from the system board 3 Detach the power button board 3 from the display panel assembly The power button board is attached to the display panel assembly with double sided adhesive ot 4 Remove the power button board and cable Reverse this procedure to install the power button board and cable Volume button board Description Spare part number Volume button board includes cable double sided adhesive and rubber pad 744541 001 Before removing the volume button board follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hiber
11. 1 and OpenVG 1 1 Supports the following video decode formats e 1080p 30fps e 720p 60fps e H 263 e H 264 e MPEG 4 e MPEG2 e DivX e WMV Supports the following video encode formats e 1080p 24fps e 720p 30fps e H 263 e H 264 BP e MPEGA4 Memory Supports 1 GB DDR3 up to 1600 MHz Mass storage Supports a 16 0 GB embedded MultiMedia Card eMMC solid state drive v 4 4 1 Audio and video Integrated stereo speakers 2 1 0 W per channel One digital microphone Support Beats Audio 5 0 MP 1080p autofocus rear facing webcamera 2 0 MP 720p front facing webcamera Sensors Chapter 1 Product description Accelerometer Ambient light sensor e Compass Gyro position Proximity HP Slate10 HD HP Slate7 HD Category Wireless networking External expansion Ports Description HP Slate10 HD HP Slate7 HD Integrated WiFi option WiFi 802 1 labgn x x Bluetooth and WiFi antenna support both 2 4G and 5G bands Integrated GPS option Supports both A GPS and standalone GPS Integrated Bluetooth option Bluetooth 3 0 HS Class 2 10m range Integrated WiDi option e GSM 850 900 1800 1900 e WCDMA 850 900 1700 1900 2100 Integrated micro SD Card Reader expandable to x x 32 GB Audio 3 5 mm headphone microphone combo x x jack supports North American type headset only Micro USB 2 0 type AB connector supports OTG and charging Power requirements Battery supports a 3 7 V 7000 m
12. 15 m to 3 048 m 50 ft to 10 000 ft Nonoperating 15 m to 12 192 m 50 ft to 40 000 ft NOTE Applicable product safety standards specify thermal limits for plastic surfaces The device operates well within this range of temperatures Chapter 6 Specifications 7 Power cord set requirements The wide range input feature of the tablet permits it to operate from any line voltage from 100 to 120 volts AC or from 220 to 240 volts AC The 3 conductor power cord set included with the tablet meets the requirements for use in the country or region where the equipment is purchased Power cord sets for use in other countries and regions must meet the requirements of the country or region where the tablet is used Requirements for all countries The following requirements are applicable to all countries and regions The length of the power cord set must be at least 1 0 m 3 3 ft and no more than 2 0 m 6 5 ft All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country or region where the power cord set will be used The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating of 125 or 250 V AC as required by the power system of each country or region The appliance coupler must meet the mechanical configuration of an EN 60 320 IEC 320 Standard Sheet C13 connector for mating with the appliance inlet on the back of the tablet Requirements
13. 7 HD 45 4 Remove the system board 4 Reverse this procedure to install the system board Antenna modules Description Spare part number 3G antenna module 747947 001 WiFi antenna module 743045 001 Before removing the antenna modules follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove the back cover see Back cover on page 37 Remove the battery see Battery on page 38 ry e p p Remove the system board see System board on page 43 46 Chapter 5 Removal and replacement procedures Remove the antenna modules 1 Remove the three Phillips PM2 0x2 75 screws 1 that secure the antenna modules to the display panel assembly 2 Detach the 3G antenna module 2 from the display panel assembly The 3G antenna module is attached to the display panel assembly with double sided adhesive 3 Detach the WiFi antenna module 3 from the display panel assembly The WiFi antenna module is attached to the display panel assembly with double sided adhesive 4 Remove the antenna modules Reverse this procedure to install the antenna modules Power button microphone module Description Spare part number Power button microphone module inclu
14. Ah 25 9 x WH Li ion battery non removable USB charging battery AC adapter supports a 10 W AC adapter with DC plug and localized cable plug support Battery supports a 3 7 V 4000 mAh 14 8 x WH Li ion battery non removable USB charging battery AC adapter supports a 10 W AC adapter with DC plug and localized cable plug support Security Software based trusted platform module x x TPM solution Operating system Preinstalled Android 4 2 x x Serviceability End user replaceable part AC adapter x x 4 2 External component identification HP Slate10 HD O 9 K 1 9 bl hoc as Q ae 044 6 6 q B 4 Item Component Item Component 1 Audio out headphone Audio in 6 Volume control buttons 2 microphone jack 2 Rear facing webcamera 7 Speakers 2 3 Microphone 8 Micro USB 2 0 port 4 Power button 9 Micro SIM slot 5 Front facing webcamera 10 Micro SD Card Reader slot Chapter 2 External component identification HP Slate7 HD He G Q9 i pe Gsm Q son Q NT Item Component Item Component 1 Rear facing webcamera 6 Speakers 2 2 Microphone 7 Audio out headphone Audio in microphone jack 3 Power button 8 Micro USB 2 0 port 4 Front facing webcamera 9 Micro SD Card Reader slot 5 Volume control buttons 2 10 Micro SIM slot HP Slate7 HD 6 3 Illustrated parts catalo
15. HP Slate10 HD and HP Slate7 HD Maintenance and Service Guide IMPORTANT This document is intended for HP authorized service providers only Copyright 2013 Hewlett Packard Development Company L P Bluetooth is a trademark owned by its proprietor and used by Hewlett Packard Company under license SD Logo is a trademark of its proprietor The information contained herein is subject to change without notice The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein First Edition October 2013 Document Part Number 741959 001 Product notice This guide describes features that are common to most models Some features may not be available on your computer Software terms By installing copying downloading or otherwise using any software product preinstalled on this tablet you agree to be bound by the terms of the HP End User License Agreement EULA If you do not accept these license terms your sole remedy is to return the entire unused product hardware and software within 14 days for a refund subject to the refund policy of your place of purchase For any further information or to request a full refund of the tablet please contact your local point of sale the seller
16. TE id 46 Power b lton microphone module rin ia ai 47 Frontfacing webcamera ra is 49 6 Spedficall Bs AA 51 AA A E EA EA EA A AS 51 HP Slate HD MR a a R eee aa ae E a 52 7 Power cord set requirements viinnnianmaianmaiia ia ERE E ER RE E ERRR CERE AMA T UEUE T QAwA 53 Requirements for all countries iaa 53 Requirements for specific countries and regions cccsesccceeeeeseeeeeeneeeeeseeeeeeceeeeeeeeeeeeeeestaeees 53 8 TTL gt a ia 55 IAE a AA AAA AAA 56 1 Product description Category Product Name Description HP Slate10 HD HP Slate10 HD HP Slate7 HD Processor Panel HP Slate7 HD Marvel PXA986 1 20 GHz dual core soldered on chip SOC processor 10 0 in 1280x800 a Si TFT TouchScreen display panel with liquid crystal display LCD 24 bit color depth 16 10 Ultra Wide Aspect Ratio WXGA 2 75 75 75 75 viewing angle single link low voltage differential signalling LVDS interface traditional capacitive multi touch gt 5 fingers 7 0 in 1280x800 a Si TFT TouchScreen display panel with liquid crystal display LCD 24 bit color depth 16 10 Ultra Wide Aspect Ratio WXGA 2 75 75 75 75 viewing angle single link low voltage differential signalling LVDS interface traditional capacitive multi touch gt 5 fingers 2 Category Description Graphics 3D and 2d GPU 2D hardware acceleration include DirectFB and alpha blending Supports OpenGL ES 2 0 1
17. amera 1 Turn the system board upside down with the bottom edge toward you 2 Release the ZIF connector 1 to which the front facing webcamera cable is attached and then disconnect the frontfacing webcamera cable from the system board 3 Remove the front facing webcamera 2 and cable Reverse this procedure to install the frontfacing webcamera Chapter 5 Removal and replacement procedures HP Slate7 HD There are as many as 16 screws that must be removed replaced and or loosened when servicing the HP Slate7 HD tablet Make special note of each screw size and location during removal and replacement Back cover Description Spare part number Back cover includes card reader slot SIM slot cover grounding pads and tape power button actuator shielding volume button actuator webcam lens and wireless antenna In bright red finish includes WiFi antenna cable and transceivers 744579 001 In silver slate finish includes WiFi antenna cable and transceivers 743041 001 Display panel assembly 7 0 in LCD TFT TouchScreen includes display panel cable 743046 001 Before disassembling the HP Slate7 HD tablet follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet 3 Disconnect all external devices from the ta
18. ansceivers Display panel assembly 10 0 in LCD TFT TouchScreen includes display panel cable 743084 001 Before disassembling the HP Slate10 HD follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet 3 Disconnect all external devices from the tablet 18 Chapter 5 Removal and replacement procedures Remove the back cover 1 Place the tablet on a flat surface display panel side up with the speakers and the micro USB port toward you Insert a case utility tool 1 or similar thin plastic tool between the back cover and the display panel assembly The first insertion point should be in the top edge of the tablet near the audio jack 2 Lift the top edge of the back cover 3 until it separates from the display panel assembly Lift the left 4 and the right sides 5 of the back cover until they detach from the display panel assembly Remove the back cover 6 Reverse this procedure to install the back cover Sensor module Description Spare part number Sensor module 744539 001 Before removing the sensor module follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system
19. ard reader slot SIM slot cover grounding pads and tape power button actuator shielding volume button actuator webcam lens and wireless antenna 743043 001 HP Slate7 HD tablet equipped with a Marvel PXA986 1 20 GHz dual core SOC processor a 7 0 in LCD TFT TouchScreen display 1 0 GB system memory a 16 GB eMMC solid state drive and WiFi in silver slate finish 743044 001 USB board for use only on HP Slate7 HD tablet models includes bracket cable double sided adhesive and micro USB port 743045 001 WiFi antenna module for use only on HP Slate7 HD tablet models includes double sided adhesive 743046 001 7 0 in LCD TFT TouchScreen display panel assembly for use only on HP Slate7 HD tablet models includes display panel cable 743047 001 Screw Kit for use only on HP Slate7 HD tablet models 743048 001 Speaker Kit for use only on HP Slate7 HD tablet models 743049 001 System board equipped with a Marvel PXA986 1 20 GHz dual core SOC processor 1 0 GB system memory a 16 GB eMMC solid state drive and WiFi for use only on HP Slate7 HD tablet models 743050 001 Frontfacing webcamera for use only on HP Slate7 HD tablet models includes cable 74305 1 001 Rear facing webcamera for use only on HP Slate7 HD tablet models includes cable and double sided adhesive 743082 001 Back cover in silver slate finish for use only on HP Slate10 HD tablet models equipped with WiFi includes media card slot power button actuator SIM slot cover sp
20. blet Remove the back cover 1 Place the tablet on a flat surface display panel side up with the micro SD Card Reader slot and micro SIM slot toward you 2 Inserta case utility tool 1 or similar thin plastic tool between the back cover and the display panel assembly The first insertion point should be in the left side of the tablet near the micro SD Card Reader slot 2 3 Lift the left side of the back cover 3 until it separates from the display panel assembly 4 Lift the top 4 and the bottom edges 5 of the back cover until they detach from the display panel assembly HP Slate7 HD 37 5 Remove the back cover 6 Reverse this procedure to install the back cover Battery Description Spare part number Battery 3 7 V 4000 mAh 14 8 WH Li ion includes cable 743895 001 Before removing the battery follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet 3 Disconnect all external devices from the tablet 4 Remove the back cover see Back cover on page 37 Z WARNING To reduce potential safety issues use only the battery provided with the tablet a replacement battery provided by HP or a compatible battery purchased from HP Z CAUTION Removing a battery that is the sole power source for
21. bright red finish 747947 001 3G antenna module for use only on HP Slate7 HD tablet models includes double sided adhesive 748790 001 Back cover in silver slate finish for use only on HP Slate10 HD tablet models equipped with WWAN capability includes media card slot power button actuator SIM slot cover speaker grilles volume button actuator and webcamera lens 748791 001 Back cover in bright red finish for use only on HP Slate10 HD tablet models equipped with WWAN capability includes media card slot power button actuator SIM slot cover speaker grilles volume button actuator and webcamera lens 751600 001 USB extension cable Sequential part number listing 13 4 Removal and replacement preliminary requirements Tools required You will need the following tools to complete the removal and replacement procedures e Magnetic screw driver e Phillips PO screw driver e Plostic case utility tool Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures Ex NOTE As you remove each subassembly from the tablet place the subassembly and all accompanying screws away from the work area to prevent damage Plastic parts ZA CAUTION Using excessive force during disassembly and reassembly can damage plastic parts Use care when handling the plastic parts Apply pressure only at the points designated in the maintenance instruct
22. ck head AC adapter for use in MERCO 744423 003 10 W USB duck head AC adapter for use in the United Kingdom and Singapore 744423 008 10 W USB duck head AC adapter for use in North America 744423 009 10 W USB duck head AC adapter for use in Europe and South Korea 744423 012 10 W USB duck head AC adapter for use in Brazil 744532 001 Back cover in bright red finish for use only on HP Slate10 HD tablet models equipped with WiFi includes media card slot power button actuator SIM slot cover speaker grilles volume button actuator and webcamera lens 744533 001 Microphone for use only on HP Slate10 HD tablet models includes cable and double sided adhesive 744534 001 HP Slate10 HD tablet equipped with a Marvel PXA986 1 20 GHz dual core SOC processor a 10 0 in LCD TFT TouchScreen display 1 0 GB system memory a 16 GB eMMC solid state drive and WiFi in bright red finish 744535 001 HP Slate10 HD tablet equipped with a Marvel PXA986 1 20 GHz dual core SOC processor a 10 0 in LCD TFT TouchScreen display 1 0 GB system memory a 16 GB eMMC solid state drive WiFi and WWAN capability in bright red finish 744536 001 USB board for use only on HP Slate10 HD tablet models includes bracket cable micro USB port and rubber pad 744537 001 Audio board for use only on HP Slate10 HD tablet models includes audio jack and bracket 744538 001 Power button board for use only on HP Slate1O HD tablet models includes cable double sided adhesive an
23. cord set fittings appliance coupler and wall plug must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used The flexible cord must be Type VCTF 3 conductor 0 75 mm conductor size Power cord set fittings appliance coupler and wall plug must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used Chapter 7 Power cord set requirements 8 Recycling When a non rechargeable or rechargeable battery has reached the end of its useful life do not dispose of the battery in general household waste Follow the local laws and regulations in your area for battery disposal HP encourages customers to recycle used electronic hardware HP original print cartridges and rechargeable batteries For more information about recycling programs see the HP Web site at http www hp com recycle 55 Index Symbols Numerics 3G antenna module removal 46 spare part number 9 13 46 A AC adapter spare part numbers 10 12 antenna removal 46 spare partnumbers 9 11 13 46 audio board removal 27 spare part number 8 12 27 audio product description 2 audio in jack 4 5 audio out jack 4 5 B back cover removal 18 37 spare part numbers 7 9 11 12 13 18 37 battery removal 20 38 spare part numbers 8 10 11 20 38 buttons power 4 5 volume control 4 5 e cables service considerations 14 card read
24. d rubber pad 744539 001 Sensor module for use only on HP Slate10 HD tablet models includes double sided adhesive 744540 001 Card reader board for use only on HP Slate10 HD tablet models includes cable micro SIM slot and micro SD Card Reader slot 744541 001 Volume button board for use only on HP Slate10 HD tablet models includes cable double sided adhesive and rubber pad 744542 001 Screw Kit for use only on HP Slate10 HD tablet models 744543 001 Speaker Kit for use only on HP Slate10 HD tablet models includes left and right speakers and cables 744544 001 Frontfacing webcamera for use only on HP Slate10 HD tablet models includes cable and double sided adhesive 744545 001 Rear facing webcamera for use only on HP Slate10 HD tablet models includes cable 744579 001 Back cover in bright red finish for use only on HP Slate7 HD tablet models includes card reader slot SIM slot cover grounding pads and tape power button actuator shielding volume button actuator webcam lens and wireless antenna Chapter 3 Illustrated parts catalog Spare part number Description 744580 001 Power button microphone module for use only on HP Slate7 HD tablet models includes cable double sided adhesive and rubber pad 744581 001 HP Slate7 HD tablet equipped with a Marvel PXA986 1 20 GHz dual core SOC processor a 7 0 in LCD TFT TouchScreen display 1 0 GB system memory a 16 GB eMMC solid state drive and WiFi in
25. d with a Marvel PXA986 1 20 GHz dual core 743049 001 SOC processor 1 0 GB system memory a 16 GB eMMC solid state drive and WiFi capability 4 3G antenna module includes double sided adhesive 747947 001 5 WiFi antenna module includes double sided adhesive 743045 001 6 Power button microphone module includes cable double sided adhesive and 744580 001 rubber pad 7 Front facing webcamera includes cable 743050 001 HP Slate7 HD tablet major components 9 Item Component Spare part number 8 Battery 3 7 V 4000 mAh 14 8 WHr Li ion battery includes cable 743895001 9 Speakers includes left and right speakers and cables 743048 001 10 USB board includes bracket cable double sided adhesive and micro USB port 743044 001 11 Display panel assembly 7 0 in LCD TFT TouchScreen 743046 001 includes display panel cable Miscellaneous parts Component Spare part number AC adapter For use in Brazil 744423 012 For use in Europe and South Korea 744423 009 For use in MERCO 744423 001 For use in North America 744423 008 For use in the United Kingdom and Singapore 744423 003 HP Slate10 HD tablet Equipped with a Marvel PXA986 1 20 GHz dual core SOC processor a 10 0 in LCD TFT 744535 001 TouchScreen display 1 0 GB system memory a 16 GB eMMC solid state drive WiFi and WWAN capability in bright red finish Equipped with a Marvel PXA986 1 20 GHz dual core SOC process
26. des cable double sided adhesive and rubber pad 744580 001 Before removing the power button microphone module follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet HP Slate7 HD 47 3 Disconnect all external devices from the tablet 4 Remove the back cover see Back cover on page 37 and then remove the following components a Battery see Battery on page 38 b System board see System board on page 43 c 3G antenna module see Antenna modules on page 46 Remove the power button microphone module 1 Turn the 3G antenna module upside down with the bottom toward you 2 Detach the power button microphone module from the rear surface of the 3G antenna module The power button microphone module is attached to the 3G antenna module with double sided adhesive 3 Turn the 3G antenna module right side up with the bottom toward you 48 Chapter 5 Removal and replacement procedures 4 Detach the power button microphone module base plate from the 3G antenna module The power button microphone module is attached to the 3G antenna module with double sided adhesive 5 Remove the power button microphone module and cable Reverse this procedure to install the power button microphone module Front
27. ds or circuitry Turn off power and input signals before inserting or removing connectors or test equipment 16 Chapter 4 Removal and replacement preliminary requirements Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation When seated wear a wrist strap connected to a grounded system Wrist straps are flexible straps with a minimum of one megohm 10 resistance in the ground cords To provide proper ground wear a strap snugly against the skin at all times On grounded mats with banana plug connectors use alligator clips to connect a wrist strap When standing use foot straps and a grounded floor mat Foot straps heel toe or boot straps can be used at standing workstations and are compatible with most types of shoes or boots On conductive floors or dissipative floor mats use foot straps on both feet with a minimum of one megohm resistance between the operator and ground To be effective the conductive must be worn in contact with the skin The following grounding equipment is recommended to prevent electrostatic damage Antistatic tape Antistatic smocks aprons and sleeve protectors Conductive bins and other assembly or soldering aids Nonconductive foam Conductive tabletop workstations with ground cords of one megohm resistance Static dissipative tables or floor mats with hard ties to the ground Field service kits Static awareness labels Material handling
28. ducing its life expectancy A CAUTION To prevent damage to the tablet when you are removing or installing internal components observe these precautions Keep components in their electrostatic safe containers until you are ready to install them Before touching an electronic component discharge static electricity by using the guidelines described in this section Avoid touching pins leads and circuitry Handle electronic components as little as possible If you remove a component place it in an electrostatic safe container The following table shows how humidity affects the electrostatic voltage levels generated by different activities Z CAUTION A product can be degraded by as little as 700 V Typical electrostatic voltage levels Relative humidity Event 10 40 55 Walking across carpet 35 000 V 15 000 V 7 500 V Walking across vinyl floor 12 000 V 5 000 V 3 000 V Motions of bench worker 6 000 V 800 V 400 V Removing DIPS from plastic tube 2 000 V 700 V 400 V Removing DIPS from vinyl tray 11 500 V 4 000 V 2 000 V Removing DIPS from Styrofoam 14 500 V 5 000 V 3 500 V Removing bubble pack from PCB 26 500 V 20 000 V 7 000 V Packing PCBs in foam lined box 21 000 V 11 000 V 5 000 V Grounding guidelines 15 Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment To avoid hand contact transport products in static safe tubes bag
29. e back cover see Back cover on page 18 a B Q N Disconnect the battery cable from the system board see Battery on page 20 Remove the speakers 1 Disconnect the speaker cables 1 from the system board 2 Release the speaker cables from the retention clips 2 and channels built into the display panel assembly HP Slate10 HD 29 3 Remove the four Phillips PM2 0x2 75 screws 3 that secure the speakers to the display panel assembly 4 Remove the speakers 4 Reverse this procedure to install the speakers USB board Description Spare part number USB board includes bracket cable micro USB port and rubber pad 744536001 Before removing the USB board follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove the back cover see Back cover on page 18 E E sola Disconnect the battery cable from the system board see Battery on page 20 30 Chapter 5 Removal and replacement procedures Remove the USB board 1 Remove the rubber pad 1 that protects the USB board cable ZIF connector 2 Release the ZIF connector 2 to which the USB board cable is attached and then disconnect the USB board cable from the system board 3 Detach the USB
30. e the rear facing webcamera and cable Reverse this procedure to install the rear facing webcamera 26 Chapter 5 Removal and replacement procedures Audio board Description Spare part number Audio board includes audio jack and bracket 744537 001 Before removing the audio board follow these steps 1 2 3 4 5 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove the back cover see Back cover on page 18 Disconnect the battery cable from the system board see Battery on page 20 Remove the audio board 1 Release the ZIF connector 1 to which the card reader board cable is attached and then disconnect the card reader board cable from the audio board Remove the two Phillips PM2 0x2 75 screws 2 that secure the audio board and bracket to the display panel assembly Remove the audio board bracket 3 and the audio board 4 HP Slate10 HD 27 Reverse this procedure to install the audio board Card reader board Description Spare part number Card reader board includes cable micro SIM slot and micro SD Card Reader slot 744540 001 Before removing the card reader board follow these steps 1 Turn off the tablet If you are unsure whether the tablet is
31. eaker grilles volume button actuator and webcamera lens 743083 001 HP Slate10 HD tablet equipped with a Marvel PXA986 1 20 GHz dual core SOC processor a 10 0 in LCD TFT TouchScreen display 1 0 GB system memory a 16 GB eMMC solid state drive and WiFi in silver slate finish 743084 001 10 0 in LCD TFT TouchScreen display panel assembly for use only on HP Slate1O HD tablet models includes display panel cable 743895 001 Battery 3 7 V 4000 mAh 14 8 WHr Li ion for use only on HP Slate7 HD tablet models includes cable 743896 001 Battery 3 7 V 7000 mAh 25 9 WHr Li ion for use only on HP Slate10 HD tablet models includes cable 744056 001 HP Slate10 HD tablet equipped with a Marvel PXA986 1 20 GHz dual core SOC processor a 10 0 in LCD TFT TouchScreen display 1 0 GB system memory a 16 GB eMMC solid state drive WiFi and WWAN capability in silver slate finish Sequential part number listing 11 12 Spare part number Description 744057 001 System board equipped with a Marvel PXA986 1 20 GHz dual core SOC processor 1 0 GB system memory a 16 GB eMMC solid state drive and WiFi for use only on HP Slate1O HD tablet models 744058 001 System board equipped with a Marvel PXA986 1 20 GHz dual core SOC processor 1 0 GB system memory a 16 GB eMMC solid state drive WiFi and WWAN capability for use only on HP Slate10 HD tablet models 744423 001 10 W USB du
32. er board removal 28 spare part number 8 12 28 Card Reader slot 4 5 56 Index connectors service considerations 14 D display panel assembly spare part numbers 8 10 11 18 37 display panel product description 1 E electrostatic discharge 15 equipment guidelines 17 external expansion product description 3 F front facing webcamera location 4 5 removal 35 49 spare part numbers 12 35 49 8 2 11 G graphics product description 2 grounding guidelines 15 guidelines equipment 17 grounding 15 packaging 16 transporting 16 workstation 16 H headphone jack 4 5 J jacks audioin 4 5 audio out 4 5 headphone 4 5 microphone 4 5 M mass storage device product description 2 memory module product description 2 microphone location 4 5 product description 2 removal 24 spare part number 8 12 24 microphone jack 4 5 model name 1 O operating system product description 3 P packaging guidelines 16 plastic parts service considerations 14 ports product description 3 USB 2 0 4 5 power button 4 5 power button board removal 22 spare part number 7 12 22 power button microphone module removal 47 spare part number 9 13 47 power cord set requirements 53 power requirements product description 3 processor product description 1 product description audio 2 display panel 1 external expansion 3 graphics 2 mass storage 2 memory module 2 microphone 2 operating system 3 por
33. g Locating the serial number product number and model number The serial number and product number of your tablet are located on the bottom edge of the tablet You may need this information when you travel internationally or when you contact support Chapter 3 Illustrated parts catalog HP Slate10 HD tablet major components Item Component Spare part number 1 Back cover includes media card slot power button actuator SIM slot cover speaker grilles volume button actuator and webcamera lens For use only on tablet models equipped with WWAN capability in bright red finish 74879 1 001 includes WWAN antenna cable and transceivers For use only on tablet models equipped with WWAN capability in silver slate finish 748790 001 includes WWAN antenna cable and transceivers For use only on tablet models equipped with WiFi capability in bright red finish 744532 001 includes WiFi antenna cable and transceivers For use only on tablet models equipped with WiFi capability in silver slate finish 743082 001 includes WiFi antenna cable and transceivers 2 Sensor module includes double sided adhesive 744539 001 3 Power button board includes cable double sided adhesive and rubber pad 744538 001 HP Slate10 HD tablet major components 7 Item Component Spare part number 4 Microphone includes cable and double sided adhesive 744533 001 5 Rear facing webcamera includes cable and doub
34. ions Cables and connectors Z CAUTION When servicing the tablet be sure that cables are placed in their proper locations during the reassembly process Improper cable placement can damage the tablet Cables must be handled with extreme care to avoid damage Apply only the tension required to unseat or seat the cables during removal and insertion Handle cables by the connector whenever possible In all cases avoid bending twisting or tearing cables Be sure that cables are routed in such a way that they cannot be caught or snagged by parts being removed or replaced Handle flex cables with extreme care these cables tear easily 14 Chapter 4 Removal and replacement preliminary requirements Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge ESD Circuitry design and structure determine the degree of sensitivity Networks built into many integrated circuits provide some protection but in many cases ESD contains enough power to alter device parameters or melt silicon junctions A discharge of static electricity from a finger or other conductor can destroy static sensitive devices or microcircuitry Even if the spark is neither felt nor heard damage may have occurred An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a normal cycle Or the device may function normally for a while then degrade in the internal layers re
35. le from the system board Detach the TouchScreen module cable 3 from the battery The TouchScreen module cable is attached to the battery with double sided adhesive Remove the four Phillips PM2 0x2 75 screws 4 that secure the speakers to the display panel assembly Remove the speakers 5 Reverse this procedure to install the speakers HP Slate7 HD 41 USB board Description Spare part number USB board includes bracket cable double sided adhesive and micro USB port 743044 001 Before removing the USB board follow these steps 1 2 3 4 5 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove the back cover see Back cover on page 37 Disconnect the battery cable from the system board see Battery on page 38 Remove the USB board 1 4 Release the ZIF connector 1 to which the USB board cable is attached and then disconnect the USB board cable from the system board Remove the USB board bracket 2 Detach the USB board 3 from the display panel assembly The USB board is attached to the display panel assembly with double sided adhesive 3 Remove the USB board and cable Reverse this procedure to install the USB board
36. le sided adhesive 744545 001 6 Audio board includes audio jack and bracket 744537 001 7 Volume button board includes cable double sided adhesive and rubber pad 744541 001 8 Card reader board includes cable micro SIM slot and micro 744540 001 SD Card Reader slot 9 System board equipped with a Marvel PXA986 1 20 GHz dual core SOC processor 1 0 GB system memory and a 16 GB eMMC solid state drive Equipped with WWAN capability 744058 001 Equipped with WiFi capability 744057 001 10 Battery 3 7 V 7000 mAh 25 9 WHr Li ion includes cable 743896 001 11 Speakers includes left and right speakers and cables 744543 001 12 USB board includes bracket cable micro USB port and rubber pad 744536 001 13 Front facing webcamera includes cable 744544 001 14 Display panel assembly 10 0 in LCD TFT TouchScreen 743084 001 includes display panel cable Chapter 3 Illustrated parts catalog HP Slate7 HD tablet major components Item Component Spare part number 1 Back cover includes card reader slot SIM slot cover grounding pads and tape power button actuator shielding volume button actuator webcam lens and wireless antenna In bright red finish includes WiFi antenna cable and transceivers 744579 001 In silver slate finish includes WiFi antenna cable and transceivers 743041 001 2 Rear facing webcamera includes cable and double sided adhesive 743051 001 3 System board equippe
37. nation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet 3 Disconnect all external devices from the tablet HP Slate10 HD 23 4 Remove the back cover see Back cover on page 18 5 Disconnect the battery cable from the system board see Battery on page 20 Remove the volume button board 1 Remove the rubber pad 1 that protects the volume button board cable ZIF connector 2 Release the ZIF connector 2 to which the volume button board cable is attached and then disconnect the volume button board cable from the system board 3 Detach the volume button board 3 from the display panel assembly The volume button board is attached to the display panel assembly with double sided adhesive 4 4 Remove the volume button board and cable Reverse this procedure to install the volume button board Microphone Description Spare part number Microphone includes cable 744533 001 24 Before removing the microphone follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet Chapter 5 Removal and replacement procedures 3 Disconnect all external devices from the tablet 4 Remove the back cover
38. off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Remove the back cover see Back cover on page 18 2 3 Disconnect all external devices from the tablet 4 5 Disconnect the battery cable from the system board see Battery on page 20 Remove the audio board 1 Release the ZIF connector 1 to which the card reader board cable is attached and then disconnect the card reader board cable from the audio board 2 Release the ZIF connector 2 to which the card reader board cable is attached and then disconnect the card reader board cable from the system board 3 Remove the two Phillips PM2 0x2 75 screws 3 that secure the card reader board to the display panel assembly 28 Chapter 5 Removal and replacement procedures 4 Remove the card reader board 4 Reverse this procedure to install the card reader board Speakers Description Spare part number Speaker Kit includes left and right speakers and cables 744543 001 Before removing the speakers follow these steps Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove th
39. or a 10 0 in LCD TFT 744056 001 TouchScreen display 1 0 GB system memory a 16 GB eMMC solid state drive WiFi and WWAN capability in slate silver finish Equipped with a Marvel PXA986 1 20 GHz dual core SOC processor a 10 0 in LCD TFT 744534 001 TouchScreen display 1 0 GB system memory a 16 GB eMMC solid state drive and WiFi in bright red finish Equipped with a Marvel PXA986 1 20 GHz dual core SOC processor a 10 0 in LCD TFT 743083 001 TouchScreen display 1 0 GB system memory a 16 GB eMMC solid state drive and WiFi in slate silver finish HP Slate7 HD tablet Equipped with a Marvel PXA986 1 20 GHz dual core SOC processor a 7 0 in LCD TFT 744581 001 TouchScreen display 1 0 GB system memory a 16 GB eMMC solid state drive and WiFi in bright red finish Equipped with a Marvel PXA986 1 20 GHz dual core SOC processor a 7 0 in LCD TFT 743043 001 TouchScreen display 1 0 GB system memory a 16 GB eMMC solid state drive and WiFi in slate silver finish Screw Kit For use only on HP Slate10 HD tablet models 744542 001 10 Chapter 3 Illustrated parts catalog Component Spare part number For use only on HP Slate7 HD tablet models 743047 001 USB extension cable 751600 001 Sequential part number listing Spare part number Description 743041 001 Back cover in silver slate finish for use only on HP Slate7 HD tablet models includes c
40. ows before removing the battery Remove the battery A CAUTION Before turning the display panel assembly upside down make sure the work surface is clear of tools screws and any other foreign objects Failure to follow this caution can result in damage to the display panel assembly 1 Place the tablet on a flat surface display panel side down with the speakers and the micro USB port toward you 2 Disconnect the battery cable 1 from the system board 3 Remove the rubber pads 2 that protect the mini USB board zero insertion force ZIF connector and the display panel cable ZIF connector 4 Release the ZIF connector 3 to which the mini USB board cable is attached and then disconnect the mini USB board cable from the system board 5 Release the ZIF connector 4 to which the display panel cable is attached and then disconnect the display panel cable from the system board 6 Detach the mini USB board cable 5 and the display panel cable from the battery The mini USB board cable and the display panel cable are attached to the battery with double sided adhesive HP Slate10 HD 21 Remove the six Phillips PM2 0x2 75 screws 1 that secure the battery to the display panel assembly Lift the top edge of the battery 2 and swing it up and back to release it Remove the battery 3 Reverse this procedure to install the battery Power button board Description Spare part number Power button board
41. packages Nonconductive plastic bags tubes or boxes Metal tote boxes Electrostatic voltage levels and protective materials The following table lists the shielding protection provided by antistatic bags and floor mats Material Use Voltage protection level Antistatic plastics Bags 1 500 V Carbon loaded plastic Floor mats 7 500 V Metallized laminate Floor mats 5 000 V Grounding guidelines 17 5 Removal and replacement procedures Tablet component replacement procedures Z CAUTION Tablet components described in this chapter should only be accessed by an authorized service provider Accessing these parts can damage the tablet and void the warranty This chapter provides removal and replacement procedures for authorized service provider only parts HP Slate10 HD There are as many as 22 screws that must be removed replaced and or loosened when servicing the HP Slate10 HD tablet Make special note of each screw size and location during removal and replacement Back cover Description Spare part number Back cover includes media card slot power button actuator SIM slot cover speaker grilles volume button actuator and webcamera lens For use only on tablet models equipped with WWAN capability in bright red finish includes 748791 001 WWAN antenna cable and transceivers For use only on tablet models equipped with WWAN capability in silver slate finish includes 748790 001 WWAN antenna cable and tr
42. s or boxes Protect ESD sensitive parts and assemblies with conductive or approved containers or packaging Keep ESD sensitive parts in their containers until the parts arrive at static free workstations Place items on a grounded surface before removing items from their containers Always be properly grounded when touching a component or assembly Store reusable ESD sensitive parts from assemblies in protective packaging or nonconductive foam Use transporters and conveyors made of antistatic belts and roller bushings Be sure that mechanized equipment used for moving materials is wired to ground and that proper materials are selected to avoid static charging When grounding is not possible use an ionizer to dissipate electric charges Workstation guidelines Follow these grounding workstation guidelines Cover the workstation with approved static shielding material Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment Use conductive field service tools such as cutters screw drivers and vacuums When fixtures must directly contact dissipative surfaces use fixtures made only of static safe materials Keep the work area free of nonconductive materials such as ordinary plastic assembly aids and Styrofoam Handle ESD sensitive components parts and assemblies by the case or PCM laminate Handle these items only at staticfree workstations Avoid contact with pins lea
43. ssosseoseosssosscossoseesseoo 14 Tools reg ired storien PP MT 14 Service consider hOnS ii A AA AAA iaa 14 Plastic Heiss oen dra o O DRR 14 Cables and AMES vasca ptr Hid A RA 14 Credis guidelines rr deri oar stays veu es cl AAA manana Pre V brain 15 Electrostatic discharge domi 15 Packaging and transporting guidelines ooooococcnnoocccconoconccononoccnconcncccnnno 16 Workstation guidelines coria cda di 16 5 Removal and replacement procedures oocccoccccoocccnocccnoccinncccnocccnocccnncccnocccnocccnoccnnccccnccnns 18 Tablet component replacement procedures ccccecceeeeeeeeeeeseeeceeeeceeeeeseseseeeecsseeeeenseesestseeeeees 18 Ln CHEER INCERTI 18 Back Cover emu becnagi 18 A o e E e e E E a S 19 weg EI 20 Power boon A erent tre tenet cever rr ane tonc en teeter ernie Serr ye ene ren creer 22 Volume button board sessssee eem eene I eese see rhh ness esse rhet essen ee 23 vi Mir ee ee en ne aR geen See ee eae nN eae ree ae oe eee 24 Rear facing webcamera erat A de 26 A 27 Card reader O POE UA 28 Speakers A 29 USB board 4 a sun aes T A A T 30 System bodid ENTIER T m 32 Frontfacing NveDeaMIe Ie core deii sait inicr di 35 HE SUE nn a e e eaaaen sane 37 oe CGV ED pri AAN 37 NON 38 Rear facing WebCOSl mitra 39 Speakers M A E A i EE EEAO 40 AA AA E UR E E E E nee etee 42 o A e e PE o II E G 43 Antenna nee U
44. the tablet can cause loss of information To prevent loss of information save your work or shut down the tablet through Windows before removing the battery Remove the battery Z CAUTION Before turning the display panel assembly upside down make sure the work surface is clear of tools screws and any other foreign objects Failure to follow this caution can result in damage to the display panel assembly 1 Place the tablet on a flat surface display panel side down with the volume control buttons toward you 2 Disconnect the battery cable 1 from the system board 38 Chapter 5 Removal and replacement procedures 3 Release the tape 2 that secures the TouchScreen cable to the battery 4 Release the speaker cables from the retention clips 3 built into the battery 5 Remove the three Phillips PM2 0x2 75 screws 4 that secure the battery to the display panel assembly 6 Remove the battery 5 Reverse this procedure to install the battery Rear facing webcamera Description Spare part number Rear facing webcamera includes cable and double sided adhesive 743051 001 Before removing the rear facing webcamera follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet 3 Disconnect all external de
45. ts 3 power requirements 3 processors 1 product name 1 security 3 sensor 2 serviceability 3 video 2 wireless networking 3 product name 1 R rear facing webcamera location 4 5 removal 26 39 spare part numbers 12 26 39 8 9 11 S Screw Kit spare part numbers 10 11 12 security product description 3 sensor module removal 19 spare part number 7 12 19 sensor product description 2 service considerations cables 14 connectors 14 plastic parts 14 serviceability product description 3 SIM slot 4 5 Speaker Kit spare part numbers 8 10 11 12 29 40 speakers location 4 5 removal 29 40 spare part numbers 12 29 40 8 10 11 system board removal 32 43 spare part numbers 8 9 11 12 32 43 T tablet major components 7 9 spare part numbers 10 11 12 13 specifications 51 52 tools required 14 transporting guidelines 16 U USB 2 0 port 4 5 USB board removal 30 42 spare part numbers 8 10 11 12 30 42 USB extension cable spare part number 11 13 v video product description 2 volume button board removal 23 spare part number 8 12 23 volume control buttons 4 5 Ww webcamera removal 26 35 39 49 spare part numbers 8 9 11 12 26 35 39 49 WiFi antenna module removal 46 spare part number 9 11 46 wireless networking product description 3 workstation guidelines 16 Index 57
46. vices from the tablet HP Slate7 HD 39 4 Remove the back cover see Back cover on page 37 5 Disconnect the battery cable from the system board see Battery on page 38 Remove the rear facing webcamera 1 Disconnect the rear facing webcamera cable 1 from the system board 2 Detach the rear facing webcamera 2 from the display panel assembly The rear facing webcamera is attached to the display panel assembly with double sided adhesive 3 Remove the rear facing webcamera and cable Reverse this procedure to install the rear facing webcamera Speakers 40 Description Spare part number Speaker Kit includes left and right speakers and cables 743048 001 Before removing the speakers follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet 3 Disconnect all external devices from the tablet Chapter 5 Removal and replacement procedures 4 5 Remove the back cover see Back cover on page 37 Disconnect the battery cable from the system board see Battery on page 38 Remove the speakers 1 2 Disconnect the speaker cable 1 from the system board Release the ZIF connector 2 to which the TouchScreen module cable is attached and then disconnect the TouchScreen module cab
Download Pdf Manuals
Related Search