Home

HP Moonshot 1500 Chassis Installation Manual

1. nareacera rar neeea cera naranereaceranenas 47 Turkey RoHS material content declaration sse en eene nere 48 Ukraine RoHS material content declaration ss 48 Warranty information seen 48 Communications interference eee 48 E O A um dod 49 Preventing electrostatic discharge lira iii ana 49 Grounding methods to prevent electrostatic discharge 49 caccia A 50 Chassis environmental specifications ssnsersnnrrsennersnnrrsnnresenerssensersnnsessnerennvensnneesenteennvensnnsensnneenn 50 Chassis specifications suisses 50 DSR and ather PENNE RR ORI O ai Before you Contact HP i 51 e RECARE ARONA IONI 51 Customer Self Repair nn arena caca nn ron nn con nn LL YDD non nnnnonnnnnn nn non nnncnnnnnnnn nano 51 Acronyms ONO 59 Desde alienati 61 FR E Mere Mr E Terie eer mms eee I 62 Contents 4 Planning the installation Safety and regulatory compliance For safety environmental and regulatory information see Safety and Compliance Information for Server Storage Power Networking and Rack Products available at the HP website http www hp com support Safety Compliance EnterpriseProducts Site requirements Select an installation site that meets the detailed installation site requirements described in the HP Moonshot System Site Planning Guide
2. The first network interface discovered by the operating system routes traffic through switch A The second network interface discovered by the operating system routes traffic through switch B Installing the chassis 31 Management network mapping MI Mo WN di All traffic from the service port management interface is routed through the iLO CM management port Removing the uplink module blank Remove the component as indicated Installing the uplink module AN CAUTION To avoid connectivity loss do not remove switches already in operation Installing the chassis 32 AN CAUTION For proper cooling be sure every switch module bay and uplink module bay has either a blank or a module installed To install the component 1 Remove the uplink module bay blank Removing the uplink module blank on page 32 2 Prepare the uplink module for installation 3 Install the uplink module 4 Do one of the following o lf the switch module is already installed verify the uplink module powers on and the uplink module health LED is green o If the switch module is not installed install the switch module before verifying LEDs For more information see Switch information and guidelines on page 29 5 After both components have been installed verify the switch firmware is at the HP recommended firmware version For more information see the HP Moonshot Compone
3. Amber Standby operation Off No power Green Normal operation Flashing Amber Degraded condition Flashing Red Critical condition Off No power Blue Chassis ID is selected Flashing blue System firmware update is in process Off Chassis ID is not selected Identifying components and LEDs 10 he pesci EN Cartridge health LEDs Switch module A health LED Switch module B health LED Green Normal operation Amber Standby mode Flashing Amber Degraded condition Flashing Amber All Moonshot 1500 CM module is not installed Flashing Red Critical condition Off Cartridge is not installed or no power exists Green Normal operation Flashing Amber Degraded condition Flashing Red Critical condition Off Switch module is not installed or no power exists Green Normal operation Flashing Amber Degraded condition Flashing Red Critical condition Off Switch module is not installed or no power exists 6 Power supply blank Identifying components and LEDs 1 Fan bay numbering Fan LED Status Description Off The fan is working or the power is off Solid amber The fan has failed Identifying components and LEDs 12 Power supply LED Status Description Off e NoAC power to power supply units Check the AC power cord e AC is present Standby output is on output is disabled e Power supply failure includes overvoltage
4. o o 115200 baud rate 8 data bits No parity 1 stop bit No flow control Start the terminal Configuring the HP Moonshot System 39 Log in to the iLO CM firmware After the terminal session is started log in as administrator at the login prompt Enter the username Administrator Enter the password password Obtain the management IP address To determine the management IP address for the Moonshot 1500 CM module log in to the iLO CM firmware while connected to the iLO CM management serial port At the prompt enter the following command show chassis info If DHCP services are unavailable on the management network configure the IP address and network mask for the Moonshot 1500 CM module Enter the following commands set network ip ip address gt set network mask lt ip address gt Obtain the MAC addresses for each cartridge node A MAC address is needed to deploy an operating system to a cartridge node To obtain the MAC addresses for each cartridge 1 Log in to the iLO CM firmware 2 Obtain MAC addresses show node macaddr all Configure the iLO CM firmware administrator account password Log in to the iLO CM firmware and change the administrator account password set user password lt user name gt lt new password gt Example set user password Administrator changed password For more information about password configuration and restrictions see the HP Moonshot iLO Chassis Management CL
5. Ul ARARE HATS CHE SHPBASHEBELET Support and other resources 56 EP BITS HORAS EA BITS CSR ABH UR Al REA E MA S 3 ER I BUE 75 RE ARR Att WMRASE HP ak HP RSRSRS FEA EDEN CSR ENTRE HP SERIE ASA TGCH TIR AA CSR ABE e RD EREA UMATE RIERA HP SAAB MX AARS SAE Wen AT 38 FR T H EPIA ZA BRUDER ERA ZA EPA RITHM Aid MRE Ex HP ABE MARHE HIER IE TRIER 3 2 HP AI SENTE RE UT ENT Minn FA RE HP BRIE RARE EA ATREA ATALAPRENTE HP BRANDE FRAME DUERDCRIERDUERBEH E AR MERO E CSR ERRE TP L EH AI BATENTE ERMAN Tas FAMA BEKRA REEN TUBE HP HALL RERA RE Bid AEB HP SEMEIA CSR ARPA ATP h HE BH EE US ARDER 4 HP WRK BISA ARTERIA HP ABARUMEMEMIRA GARA 5 IMEA HERRA HP A 5AF RF PT IE DEAS AAA AAA AEB RRRA SERIE HP TRE SERIE NEAR AARTE HP OKIBEUB ARIE BORA HEEE A A o FX HP AATRES WSE LAVARSI A BRA AAKA tR ia HP Risk http www hp com go selfrepair ZAP Biz HP makat TAS l APATE i CSR HIER RHEE gt WAS SR TRUBHIESE CERSBE EX BORNE o ANR TE 52A RH HP E8 HP ARR FE RSI WEHR T fF n LFS CSR E HRE gt RI HP H6B FEED ARAE AH GMA ER o CSR SEED APRA BRIA SAETHER EF EMEA o IRE HP FREE HP EEE Hutt ARIS AT SS 95 NEL ES FH ERAS Bh AAS MN SRR THEATERS BEREA EHS TD RT FE B THE ZZ FB o MA 2n RER HP AIM gt BI RTEERE LH RT RE BEAR gt mete Awe A Ra MEME o ERE Rt HP SARS HBS ATREA BNREFPRE HP SESHRMEBUBRTECUE TS SAS ft o BHEHCEERWSEHBERR gt META ac EH
6. Als HP of een HP Service Partner bij de diagnose vaststelt dat de reparatie kan worden vitgevoerd met een CSR onderdeel verzendt HP dat onderdeel rechtstreeks naar u zodat u het defecte onderdeel daarmee kunt vervangen Er zijn twee categorie n CSR onderdelen Verplicht Onderdelen waarvoor reparatie door de klant verplicht is Als u HP verzoekt deze onderdelen voor u te vervangen worden u voor deze service reiskosten en arbeidsloon in rekening gebracht Optioneel Onderdelen waarvoor reparatie door de klant optioneel is Ook deze onderdelen zijn ontworpen voor reparatie door de klant Als u echter HP verzoekt deze onderdelen voor u te vervangen kunnen daarvoor extra kosten in rekening worden gebracht afhankelijk van het type garantieservice voor het product OPMERKING Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant In verband met de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden vervangen Deze onderdelen worden in de geillustreerde onderdelencatalogus aangemerkt met Nee Afhankelijk van de leverbaarheid en de locatie worden CSR onderdelen verzonden voor levering op de eerstvolgende werkdag Levering op dezelfde dag of binnen vier uur kan tegen meerkosten worden aangeboden indien dit mogelijk is gezien de locatie Indien assistentie gewenst is belt u een HP Service Partner om via de telefoon technische ondersteuning te ontvangen HP vermeldt in de documentatie bij het verva
7. LO CM management port The iLO CM management port is located on the Moonshot 1500 CM module on the rear of the chassis WY ERRE ISO Li CESTO anw MA a Di LI me il Now EX X Cr Data center production network To connect the chassis to a production network connect to any available SFP or QSFP port The SFP QSFP ports are located on the uplink module installed in the rear of the chassis e Moonshot 6SFP Uplink Module Cabling the HP Moonshot System 37 e Moonshot 4GSFP Uplink Module femelles Connecting power cables and applying power to the chassis 1 Connect the power cables to the power supplies 2 Connect the power cables to the power source UPS or wall outlet or to an installed PDU 3 Wait while the chassis powers on Power on events The following power on events occur after applying power to the chassis 1 Fans begin operating LO starts Front panel LEDs display the status of initializing components o Switches begin initializing o Cartridges begin initializing 4 iLO runs fan and power tests Routing cables on the cable management arm Route all rear panel cables through the cable management arm For more information about the cable management arm see the Quick Deploy Rail System Installation Instructions that ship with the Quick Deploy Rail System kit or in the HP Moo
8. Moonshot 1500 CM module health LED Chassis internal components Up to 45 cartridges and two switch modules can be installed in the HP Moonshot 1500 Chassis Identifying components and LEDs 17 Cartridge slot and switch module bay identification The chassis provides 45 cartridge slots 1 45 and two switch module bays A B 00000 a T I o a a a 4 l VJ ie Goo 8 9 x vo oo Bn S uH EA Ear 3 a E ILLU o 7 a DD _ 8 8 9 C ges DI WB leo MID doc C eo coll D bol pas Ex sens gyd bed lassa 2111 11141 Ve AA CE Do Ld g CI E D De E iit tee is te 8 mel Ci COMI is i jm L LL LI Il DADA AAA 439 425 459 499 EU i Ie ir lele O Nel NEN D CT O o O Toi SEL Hea aL Hi NES St Jal 7 Em FS t as as DB ss E UB NB C isst B fa um 10 n s 9 9 A a T ii a 4 Identifying components and LEDs 18 Cartridge LEDs and buttons Description Sas Cartridge power Green Normal operation LED button Amber Standby operation Off No power Cartridge health LED Green Normal operation Flashing amber Degraded condition Flashing red Critical condi
9. Si precisa asistencia t cnica puede llamar al Centro de asistencia t cnica de HP y recibir ayuda telef nica por parte de un t cnico Con el env o de materiales para la sustituci n de componentes CSR HP especificar si los componentes defectuosos deber n devolverse a HP En aquellos casos en los que sea necesario devolver alg n componente a HP deber hacerlo en el periodo de tiempo especificado normalmente cinco d as laborables Los componentes defectuosos deber n devolverse con toda la documentaci n relacionada y con el embalaje de env o Si no enviara el componente defectuoso requerido HP podr cobrarle por el de sustituci n En el caso de todas sustituciones que lleve a cabo el cliente HP se har cargo de todos los gastos de env o y devoluci n de componentes y escoger la empresa de transporte que se utilice para dicho servicio Support and other resources 54 Para obtener m s informaci n acerca del programa de Reparaciones del propio cliente de HP p ngase en contacto con su proveedor de servicios local Si est interesado en el programa para Norteam rica visite la p gina web de HP siguiente http www hp com go selfrepair Customer Self Repair Veel onderdelen in HP producten zijn door de klant zelf te repareren waardoor de reparatieduur tot een minimum beperkt kan blijven en de flexibiliteit in het vervangen van defecte onderdelen groter is Deze onderdelen worden CSR onderdelen Customer Self Repair genoemd
10. example 238 2 for 2002 and 38 for the week of September 9 In addition 2010 is indicated by O 2011 by 1 2012 by 2 2013 by 3 and so forth e YYWW where YY indicates the year using a base year of 2000 For example 0238 02 for 2002 and 38 for the week of September 9 Turkey RoHS material content declaration T rkiye Cumhuriyeti EEE Y netmeli ine Uygundur Ukraine RoHS material content declaration O01a7HaHHS Bimmogigae BHMOram TexHiuHoro perJIaMeHTy MOJO OGMEXKEHHA BHKOPHCTaHHA ACAKHX HeOe3IIeuHHX DeuoBHH B eeKTPH4HOMV Ta eIeKTpoHHOMV 00 1a JHaHHi 32TBEP PKEHOTO TlocTaHoBow Ka inery Minictpis Yxpainu Bia 3 rpvaHa 2008 Ne 1057 Warranty information HP ProLiant and X86 Servers and Options http www hp com support ProliantServers Warranties HP Enterprise Servers http www hp com support EnterpriseServers Warranties HP Storage Products http www hp com support Storage Warranties HP Networking Products http www hp com support Networking Warranties Communications interference HP system compliance tests are conducted with HP supported peripheral devices and shielded cables such as those received with the system The system meets interference requirements of all countries in which it is sold These requirements provide reasonable protection against interference with radio and television communications Installing and using the system in strict accordance with HP instructions minimizes the chances that the system mi
11. innerhalb von vier Stunden gegen einen Aufpreis verfigbar Wenn Sie Hilfe ben tigen k nnen Sie das HP technische Support Center anrufen und sich von einem Mitarbeiter per Telefon helfen lassen Den Materialien die mit einem CSR Ersatzteil geliefert werden k nnen Sie entnehmen ob das defekte Teil an HP zur ckgeschickt werden muss Wenn es erforderlich ist das defekte Teil an HP zur ckzuschicken m ssen Sie dies innerhalb eines vorgegebenen Zeitraums tun in der Regel innerhalb von f nf 5 Gesch ftstagen Das defekte Teil muss mit der zugeh rigen Dokumentation in der Verpackung zur ckgeschickt werden die im Lieferumfang enthalten ist Wenn Sie das defekte Teil nicht zur ckschicken kann HP Ihnen das Ersatzteil in Rechnung stellen Im Falle von Customer Self Repair kommt HP f r alle Kosten f r die Lieferung und R cksendung auf und bestimmt den Kurier Frachtdienst Weitere Informationen ber das HP Customer Self Repair Programm erhalten Sie von Ihrem Servicepartner vor Ort Informationen ber das CSR Programm in Nordamerika finden Sie auf der HP Website unter http www hp com go selfrepair Reparaciones del propio cliente Los productos de HP incluyen muchos componentes que el propio usuario puede reemplazar Customer Self Repair CSR para minimizar el tiempo de reparaci n y ofrecer una mayor flexibilidad a la hora de realizar sustituciones de componentes defectuosos Si durante la fase de diagn stico HP o los proveedores o
12. on a maximum temperature of 45 C 113 F Altitude maximum for storage corresponds to a pressure minimum of 70 kPa 10 1 psia Chassis specifications 18 96 cm 7 46 in 84 91 cm 33 43 in 44 33 cm 17 45 in Weight fully loaded 81 65 kg 180 00 Ib Specifications 50 Support and other resources Before you contact HP Be sure to have the following information available before you call HP e Technical support registration number if applicable e Product name e Chassis serial number e Product identification number e Applicable error messages e Operating system type and revision level To obtain product information log in to LO CM firmware and use the Show Chassis Info command For more information see the HP Moonshot iLO Chassis Management CLI User Guide in the HP Moonshot Information Library http www hp com go moonshot docs HP contact information For United States and worldwide contact information see the Contact HP website http www hp com go assistance In the United States e To contact HP by phone call 1 800 334 5144 For continuous quality improvement calls may be recorded or monitored e Ifyou have purchased a Care Pack service upgrade see the Support amp Drivers website http www8 hp com us en support drivers html If the problem cannot be resolved at the website call 1 800 633 3600 For more information about Care Packs see the HP website http pro aq sama houston hp com
13. pi ces les co ts de d placement et main d ceuvre du service vous seront factur s Facultatif Pieces pour lesquelles la r paration par le client est facultative Ces pi ces sont galement concues pour permettre au client d effectuer lui m me la r paration Toutefois si vous demandez HP de remplacer ces pi ces l intervention peut ou non vous tre factur e selon le type de garantie applicable 4 votre produit REMARQUE Certaines pi ces HP ne sont pas con ues pour permettre au client d effectuer lui m me la r paration Pour que la garantie puisse s appliquer HP exige que le remplacement de la pi ce soit effectu par un Mainteneur Agr Ces pi ces sont identifi es par la mention Non dans le Catalogue illustr Les pi ces CSR sont livr es le jour ouvr suivant dans la limite des stocks disponibles et selon votre situation g ographique Si votre situation g ographique le permet et que vous demandez une livraison le jour m me ou dans les 4 heures celle ci vous sera factur e Pour b n ficier d une assistance t l phonique appelez le Centre d assistance technique HP Dans les documents envoy s avec la pi ce de rechange CSR HP pr cise s il est n cessaire de lui retourner la pi ce d fectueuse Si c est le cas vous devez le faire dans le d lai indiqu g n ralement cinq 5 jours ouvr s La pi ce et sa documentation doivent tre retourn es dans l emballage fourni Si vous ne retournez pas la pi ce d fe
14. rails The chassis requires installation in a rack To install the rack rails see the Quick Deploy Rail System Installation Instructions that ship with the Quick Deploy Rail System kit Installing the chassis in the rack Installing the chassis 21 D b b pb WARNING The chassis is very heavy To reduce the risk of personal injury or damage to the equipment do the following e Observe local occupational health and safety requirements and guidelines for manual material handling e Get help to lift and stabilize the product during installation or removal especially when the product is not fastened to the rails The chassis weighs more than 81 65 kg 180 00 Ib so at least four people must lift the chassis into the rack together An additional person may be required to help align the chassis if the chassis is installed higher than chest level WARNING To avoid risk of personal injury or damage to the equipment do not stack anything on top of rail mounted equipment or use it as a work surface when extended from the rack WARNING To reduce the risk of personal injury or damage to the equipment be sure that The rack is bolted to the floor using the concrete anchor kit e The leveling feet extend to the floor e The full weight of the rack rests on the leveling feet e The racks are coupled together in multiple rack installations e Only one component is extended at a time If more than one component is extended a rack might b
15. services cache 10950 0 0 225 121 html Customer Self Repair HP products are designed with many Customer Self Repair CSR parts to minimize repair time and allow for greater flexibility in performing defective parts replacement If during the diagnosis period HP or HP service providers or service partners identifies that the repair can be accomplished by the use of a CSR part HP will ship that part directly to you for replacement There are two categories of CSR parts e Mandatory Parts for which customer self repair is mandatory If you request HP to replace these parts you will be charged for the travel and labor costs of this service e Optional Parts for which customer self repair is optional These parts are also designed for customer self repair If however you require that HP replace them for you there may or may not be additional charges depending on the type of warranty service designated for your product Support and other resources 51 NOTE Some HP parts are not designed for customer self repair In order to satisfy the customer warranty HP requires that an authorized service provider replace the part These parts are identified as No in the Illustrated Parts Catalog Based on availability and where geography permits CSR parts will be shipped for next business day delivery Same day or four hour delivery may be offered at an additional charge where geography permits If assistance is required you can call t
16. ti twork production network 37 UID button 17 19 R UIDLED 17 19 unpacking the components 21 rack resources 21 updating firmware 40 41 43 rear panel components 11 uplink module 9 13 14 15 32 regulatory compliance identification numbers 5 uplink module components 13 15 regulatory compliance information 5 47 USB connector 16 regulatory compliance notices 5 47 remote management 42 W required information 51 warranty information 48 requirements power 5 6 website HP 51 requirements site 5 resources 46 51 RoHS 48 S safety considerations 5 49 safety information 5 serial label pull tab 10 serial port 16 series number 5 server specifications 50 setting the admin password 40 site requirements 5 space requirements 7 21 specifications 5 7 8 50 specifications chassis 50 specifications environmental 50 static electricity 49 support 51 support and other resources 51 switch firmware updating 43 switch guidelines 29 switch health LEDs 10 20 switch information 29 switch module 9 29 33 switch module bay numbering 18 switch module configuring 41 system configuration 39 T Taiwan battery recycling notice 5 Index 64
17. to fill empty vertical spaces in the rack This arrangement ensures proper airflow Using a rack without blanking panels results in improper cooling that can lead to thermal damage Racks provide proper server cooling from flow through perforations in the front and rear doors that provide a 65 open area for ventilation Temperature requirements To ensure continued safe and reliable equipment operation install or position the rack in a well ventilated climate controlled environment The operating temperature inside the rack is always higher than the room temperature and is dependent on the configuration of equipment in the rack Check the TMRA for each piece of equipment before installation AN CAUTION To reduce the risk of damage to the equipment when installing third party options e Do not permit optional equipment to impede airflow around the chassis or to increase the internal rack temperature beyond the maximum allowable limits e Do not exceed the manufacturer s TMRA Grounding requirements This equipment must be grounded properly for proper operation and safety In the United States you must install the equipment in accordance with NFPA 70 1999 Edition National Electric Code Article 250 as well as any local and regional building codes In Canada you must install the equipment in accordance with Canadian Standards Association CSA C22 1 Canadian Electrical Code In all other countries you must install the equipment i
18. 48 determining the chassis rack spacing 21 diagnosing problems 46 disposal battery 5 documentation 6 61 documentation feedback 61 electrostatic discharge 49 environmental considerations 48 environmental requirements 50 EuroAsian Economic Commission 47 European Union notice 5 F fan bay 12 fan LED 12 fans 9 11 12 28 fans installing 28 Federal Communications Commission FCC notice 5 Index 62 firmware 40 41 43 firmware upgrade utility troubleshooting 46 front panel components 10 19 G grounding methods 49 grounding requirements 8 H health LED 10 17 20 help resources 51 hot plug power supply calculations 6 HP Advanced Power Manager 6 HP APM 6 HP contact information 51 HP Moonshot 1500 Chassis Management module 9 11 17 HP Moonshot 1500 Chassis Management module components 16 HP Moonshot 1500 Chassis Management module LEDs and buttons 17 HP technical support 51 HP website 51 HP contacting 51 HP APM port 16 iLO CM link port 16 iLO CM link port activity LED 17 iLO CM link port link LED 17 iLO CM management port 16 iLO CM management port activity LED 17 iLO CM management port link LED 17 iLO CM management serial port 16 installation overview 5 21 installation blanking panel 25 installation cable management arm 38 installation cartridge 29 installation chassis 21 installation fans 28 installation network components 29 installation rack rails 21 installation switch mo
19. ANS REIS eat AA F CSR SHS FBT E ALURIESE gt HERA Tt FERE ARS AGE BR RES SAA MIB ABS VAE HP LIED UB dx AR EA Sia RBS o TRIER DIARIO HP ABER CSR HAREE AAMA ERA o ARR ERE HP RARE ERAAN GER AA 5 ALFA 49880480 HP ARI AMARA DEI A BR DA EO RR ERE f SC E o MRAZ HP AIRES IESE o HEARTH gt HP SARA FfEY FR RADAR E FB Yf FEE SAAR MERA gt ANB HP B3 CEPAS FEMEA gt RE IAEA c 25542575 gt SH HP 48 yh http www hp com go selfrepair o Support and other resources 57 al7H LE Sel HP AES el AZS ASOD AHO Uc PE WA A HS 8548 LAS FUSS 317 AH DA dz FEICS FES OS ASSO GATE NEU AG 7 71 Set HP HP ALES SEMA FE MBIA ERAM CSR FES MASSA Fel IES SIEN EE HPE aS TES HS ASA HO APSA Dal amp USS SUC CSR FEAE FIH EFI EUC 2A dz Selz 9 ARO US PE AS App HPO 0 FES DAS 23 ASP o A1H Ao CH st BSH 3 SOE SPEL DAUZ 2 7 MER APSO AB O FEST JA ME SOI ES BA A uc SEA DH ABAH HPO 0 FSS WAS LEE 39 ASAE TAS Al Sl Soc ES MUS SS uper 7 HIS 20 WA 5E UE a AUF HP 52 NA AL SSI IES BA MELO HPE SALUE NA 2358 Sol Sel AHIS HEHE Sol FES MAS sr USC Ast 4352 Illustrated Parts Catalogoll No erat EA S O NEUE CSR F e Mu SES AAA 240 ASSE 39 CE SAA d o 75545 830 o O l L CF Kel 240 Este 39 27 HBO amp 75 LALR SA Es ANZ MSO 215 PE NEU ESO Sese HP IIS AS MES ASPAS HE SAV ASIE SSS E AAU HPE ato IS TES HPS YEO SFE OFS CSR WA FEA EM HSE ASO ABU BBO Hes FSS HPS tags SPOE ABE IL uses SAA 217
20. HP Moonshot 1500 Chassis Setup and Installation Guide Abstract This document contains setup installation and configuration information for the HP Moonshot System This document is for the person who installs administers and troubleshoots the HP Moonshot System HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels Part Number 711993 004 June 2014 Edition 4 Copyright 2013 2014 Hewlett Packard Development Company L P The information contained herein is subject to change without notice The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein Microsoft and Windows are U S registered trademarks of the Microsoft group of companies Contents Panning AAA A 5 Safety and regulatory conplialbe csi se GG GUI OR anelli 5 SITE SOUS SINS RE RE MR NR a nn ini 5 Software Prerequisites iii 5 Determine power and cooling configurations ss 5 Eto UE ale 5 HP Adyanced AN a 6 Hotplug power supply Cal CUlGHONS cssiccsscnsocsevsscnevnssesosvanssensvensvtaresasesusnnnsnsavnsnassessenshaseosiensdensesnsnsnses 6 Compiling the a 6 o ass CD FFF
21. I User Guide in the HP Moonshot Information Library http www hp com go moonshot docs Update the firmware for the HP Moonshot System components Enter the following command to flash the specified image file from the NAND or URL to the appropriate devices update firmware lt filename gt lt url gt force lt Cx gt sA sB all When flashing the iLO firmware a known good copy of the firmware is kept in reserve until the iLO firmware is successfully flashed When flashing cartridges the command accepts multiple cartridges in the argument To flash all cartridges in the chassis specify a11 in the argument Configuring the HP Moonshot System 40 Always use the recommended firmware version for all Moonshot System components For more information on recommended firmware versions see the HP website http www hp com go moonshot download Updating firmware HP recommends updating the firmware in the following order e LO CM firmware e Cartridge firmware e Switch firmware For available firmware updates see the HP website http www hp com go moonshot download Chassis and cartridge firmware A system ROM flash does not take effect on a node until the node is rebooted The iLO CM firmware will reflect the system ROM flash immediately To update the firmware 1 Verify the firmware version by entering one of the following commands show firmware revisions all show firmware revisions list 2 Download the la
22. N RF E E en ceia 17 Cartridge slot and switch module bay identification 18 Cartridge LEDs and bce 19 Switch module button sensor and LEDS nnee ieu 20 uu iu RO ATTO 21 E O UD EE 21 Unpacking ine HF M onshot ylenia 21 Determining the chassis rack spacing i A naine ns 21 installing the tack rails ico 21 alg ise inthe rack 00 25 90 50 006 99005200 on E E E E EE EE EE E E E e es 21 Installing the blanking puitigl ioi e desea id 25 Installing HP Moonshot SC ell 26 Installing the Moonshot 1500 CM module lle 27 stalling a power Supply use A v ANO 27 Instala Ihe Tab a ea RES MEHR 28 installing the OH FIR MOIS S uo MOD MODO ONDE MM 29 Contents 3 Installing network components vrrreriririeionieniozazezionioniniozeionienioioneceazioninizioneanionioierezinecenecizionicn 29 CA AAA A 36 cun 36 Connecting the Moonshot System to a network cai 36 Data center e B ON DOS 36 Data center production network sise 37 Connecting power cables and applying power to the chassis nine 38 Poweron Vens nnb 38 Routing cables on the cable management arm soa a WO ORIG EO RDUM 38 Configuring the HP Moonshot laminas narnia 39 Chassis configuration overview seen 39 Bola MSM ENS A NI 39 Leila 41 Powercapping MERERETUR 44 Power capping RR 44 Configuring d power COP ra 44 O FROSINONE 46 MA io ani mes Un DI M dau 46 nr di MR tion A O AR ai 47 Safety and regulatory A abies 47 Belarus Kazakhstan Russia marking
23. RD HR EF YRU FER REU NN FEFENO FDFFDDF FEDR FFA UE REU SF 6 Space and airflow requirements assnnneneneresnnenseneerenerssnnensnneesenerensnsensnnsenenseesnerssnnvensnsenseneensnneenenen 7 Temperature requirements 8 Grounding equi 8 o EINE v HP Moonshot System components suisses 9 Chassis front panel components i 10 Chassis front panel LEDs and buttons nuu iii 10 Chassis rear panel components na erena rara na LLED LLAD ELLA DL eaea EEaren renean neee 1 A O A 12 Fon LED eee 12 Power supply bay numbering nnnee onee enner onee ennernnereneeennernnersneenneersnereneennnennneneneennennneneneenn 12 Power supply i DA 13 Uplink module bay identification sis 13 Moonshot 6SFP Uplink Module components saneenoneeerenerrsenressnerenenerssnneessnsrenenerssnnersenenn 13 Moonshot 6SFP Uplink Module LEDs and buttons snsensnnnerennersnnrssnnreneneresnrensnsresenerssnversenen 14 Moonshot 4QSFP Uplink Module components sanseroneeeseneersenrensnerensnrersnnsensneeeseneessnneesenen 15 Moonshot 4QSFP Uplink Module LEDs and buttons sannaesennersnnersnerenensersnenessneresenerssnversenenn 15 HP Moonshot 1500 Chassis Management module components 16 HP Moonshot 1500 Chassis Management module LEDs and buttons nna ennn ernnereneeeneerenereneenn 17 Chassis internalcomponeN IS encata ERI
24. SVO HPS ttt OF BHIC o uj Ao SYS SEP ASE ES MEO SO UA ASA EPA BEHO BILICH A Bro EY st Sas USE do SP HP7t wal LEO Wo HSS STS USUC VA SE Hel SS HPE 22235275 W Hse Teoh 038 SSAA B SH HEILS FIGC HP 224 AE Sel Ee lol CHS AME US2 7172 MAA ASAA ESSAIS sin AS z214 HAE HP AFO E htip www hp com go selfrepair B ESHA Support and other resources 58 Acronyms and abbreviations CM chassis management CPLD complex programmable logic device DHCP Dynamic Host Configuration Protocol HP APM HP Advanced Power Manager iLO Integrated Lights Out PDU power distribution unit QSFP enhanced quad small form factor pluggable SCP Secure Copy Protocol SFP small form factor pluggable SFP enhanced small form factor pluggable SFTP Secure File Transfer Protocol SSH Secure Shell Acronyms and abbreviations 59 TFTP Trivial File Transfer Protocol UPS uninterruptible power system Acronyms and abbreviations 60 Documentation feedback HP is committed to providing documentation that meets your needs To help us improve the documentation send any errors suggestions or comments to Documentation Feedback mailto docsfeedback hp com Include the document title and part number version number or the URL when submitting your feedback Documentation feedback 61 Index A access panel 9 accessing the CLI 42 activity LED 10 administrator password 40 airflow requirements 7 auth
25. a as pe as de reparo feito pelo cliente a HP paga todas as despesas de transporte e de devolu o da pe a e determina a transportadora servi o postal a ser utilizado Para obter mais informa es sobre o programa de reparo feito pelo cliente da HP entre em contato com o fornecedor de servi os local Para o programa norte americano visite o site da HP http www hp com go selfrepair hAA X tu bM Y SER RL KERMOR BHIA ORRE ERI o1 l HR m AOR U EF EEDE CSR Das E EAT AUTANT E DEA HPEH ERRTFTREE 2 4 Lit HIZO BEES SERIAL HSRICRMLTILESES CSRilnl labi FO2BURADU ET BR AABY LILIVATABYHAOMM MB DUT bL EBERA HPI ARA ARANA lt TOBEY ERI A RERAKLUAHENBERIERINET FRB DASI LILIVATHREBCHSMR COMMENAZY LILIVAPT RCS MAREO 4 Lt EEKAHP HREM ARE SN 218 SII BEU EITOS RIF amp dv SIE EX ABONO ANI BUTE AE RES LTULME REX CER lt REY EXZSRITSZCEACEETF ik PERO ROBA AARY LILIVATACULHVECA LADRI 61 DIX HE T IE HPIERR RSTE RBIS amp 8 SE HRESEDUDZR CU xd Maha nI SBRRMAAZRI LILIVAP Hn CHS SMCMENTHIET aR AA REGIA Hil ko TIA CRAM TESRAIE lt KIICBALET EK MICRO TIE PT LIST Na ESA lt EIA DE ETS NEU ET T FANER E SS POBRES NADIE ULT ARRE MENTA FM ALSO RAD CSR B da Eli EDI IK BEE tH RAT 4 EA 5m ES HART ACW MUAH EHPIUE ZEIDEN eo o eld RERBA AASF KANA CMMBREHPIORALTCE EL RENDER IDEE BULRORAARICBBERCCLICANTCESL HEE ARAU HP DAE FADER SENET HARIAN 70Olel l amp HPA d
26. and overtemperature AC is present and main 12 V output is enabled Uplink module bay identification Identifying components and LEDs 13 em mporem Joest NET SFP ports X1 X6 1Gb or 10Gb Ethernet SFP ports X1 through X6 support Ethernet traffic only SFP ports support the following pluggable Ethernet transceiver modules e HP 1000BASE T SFP e HP IOGBASE SR SFP e HP 10GBASE DAC SFP Any available port can be used to connect to the data center Ensure the port is populated with supported HP transceiver modules that are compatible with the data center port type Moonshot 6SFP Uplink Module LEDs and buttons mmm A A A mmm id MON Uplink module UID Solid blue Switch module ID is selected LED button Flashing blue Switch module firmware update is in progress Off Switch module ID is not selected Uplink module health Green Normal operation LED Flashing amber Degraded condition Flashing red Critical condition Off No power 3 Uplink module link Solid green Link LED Off No link 4 Uplink module Flashing green Activity activity LED Off No activity Reset button Resets the switch module Identifying components and LEDs 14 Moonshot 4QSFP Uplink Module components e emer eo QSFP ports Q1 G4 40Gb Ethernet QSFP ports Q1 through Q4 support Ethernet traffic only QSFP ports suppo
27. atory compliance For safety environmental and regulatory information see Safety and Compliance Information for Server Storage Power Networking and Rack Products available at the HP website http www hp com support Safety Compliance EnterpriseProducts Belarus Kazakhstan Russia marking HL Manufacturer Hewlett Packard Company Address 3000 Hanover Street Palo Alto California 94304 U S Local representative information Russian e HP Russia 3AO X ionerrl laxxapn A O 125171 Poccua r Mockea J lenwnrpancxoe wocce 16A crp 3 ren baxc 7 495 797 35 00 7 495 287 89 05 e HP Belarus NOOO Xbroner laxxapn ben 220030 benapycb r Munck yn WrepHauymoHanbHas 36 1 obuc 722 723 ten 375 17 392 28 18 paxc 375 17 392 28 21 e HP Kazakhstan TOO X ionerrl lakkapg K 050040 KazaxcraH r Anmarbi bocraHnpikckk4 pa on yn Tumnpazesa 28B 1 stax ten paxc 7 727 355 35 50 7 727 355 35 51 Local representative information Kazakh LIC Xeronerrl laxxapa K Kazakcran Anmarbi K BocrangbiK aygaHbi Tumnpszes Kci 28B ten paxc 7 727 355 35 50 7 727 355 35 51 Manvfacturing date The manufacturing date is defined by the serial number HP serial number format for this product CCSYWWZZZZ Regulatory information 47 Valid date formats include the following e YWW where Y indicates the year counting from within each new decade with 2000 as the starting point For
28. connecting an g y power components AN CAUTION To avoid damaging the fiber cables do not drape cables from one side of the rack to the other and do not run cables over a hard corner or edge After the hardware is installed complete the following cabling procedures 1 Connect the Moonshot System to a network Connecting the Moonshot System to a network on page 36 2 Connect power cables to the chassis Connecting power cables and applying power to the chassis on page 38 3 Route cables on the cable management arm Routing cables on the cable management arm on page 38 Connecting the Moonshot System to a network Data Connect the Moonshot System to the following networks e Data center management network on page 36 e Datacenter production network on page 37 center management network To connect the chassis to a management network connect an Ethernet cable from the Moonshot 1500 CM module to the management network Always connect to the iLO CM management port first Do not connect both the iLO CM management port and the iLO CM link port to the same network switch For information about enabling the iLO link port using the set network daisy command see the HP Moonshot iLO Chassis Management CLI User Guide in the HP Moonshot Information Library http www hp com go moonshot docs Cabling the HP Moonshot System 36 Moonshot iLO CM firmware SSH sessions and switch SSH sessions share connectivity through the
29. ctueuse HP se r serve le droit de vous facturer les co ts de remplacement Dans le cas d une pi ce CSR HP supporte l ensemble des frais d exp dition et de retour et d termine la soci t de courses ou le transporteur utiliser Pour plus d informations sur le programme CSR de HP contactez votre Mainteneur Agr e local Pour plus d informations sur ce programme en Am rique du Nord consultez le site Web HP http www hp com go selfrepair Support and other resources 52 Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilita nella sostituzione di parti difettose i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente CSR Customer Self Repair Se in fase di diagnostica HP o un centro di servizi o di assistenza HP identifica il guasto come riparabile mediante un ricambio CSR HP lo spedir direttamente al cliente per la sostituzione Vi sono due categorie di parti CSR Obbligatorie Parti che devono essere necessariamente riparate dal cliente Se il cliente ne affida la riparazione ad HP deve sostenere le spese di spedizione e di manodopera per il servizio Opzionali Parti la cui riparazione da parte del cliente facoltativa Si tratta comunque di componenti progettati per questo scopo Se tuttavia il cliente ne richiede la sostituzione ad HP potrebbe dover sostenere spese addizionali a seconda del tipo di garanzia p
30. dule 33 installation uplink module 32 installing a cartridge 29 installing the chassis 21 installing the rack rails 21 IP address viewing 40 42 J Japanese notice 5 L LED identification 9 LED cartridge health 19 LED drive health 19 LED health 10 19 20 LED link 19 LED UID 19 LEDs 10 19 20 LEDs front panel 10 19 LEDs power supply 13 LEDs troubleshooting 10 46 LEDs unit identification UID 10 20 link LED 19 log in to iLO CM 40 M MAC address viewing 40 management module connectors 17 management module LEDs 17 management network 36 microSD card slot 16 modifications FCC notice 5 Moonshot 1500 CM module 9 11 27 Moonshot 1500 CM module components 16 Moonshot 1500 CM module diagnostic port 16 Moonshot 1500 CM module health LED 17 Moonshot 1500 CM module LEDs and buttons 17 Moonshot 1500 CM module MicroSD slot 16 Moonshot 1500 CM module UID LED button 17 Moonshot 1500 CM module USB connector 16 N network components installing 29 O optional components 26 overview installation 21 P power cap configuring 44 power capping 44 power capping modes 44 power cord 38 power supplies 9 11 12 27 Index 63 power supply LEDs 13 technical support 51 power supply installing 27 telephone numbers 51 power up procedure 38 temperature requirements 8 powering up 38 troubleshooting 46 Power on events 38 troubleshooting resources 46 preparation procedures 5 prerequisites 5 U
31. e CPLD update Permanent damage will occur to the switch CPLD updates may last up to 10 minutes update cpld The CPLD update reloads the switch and completes when the switch returns to an operational state If no CPLD update is found the update is not performed Optional Make a backup of the image copy primary alternate This step overwrites the previous firmware version Before committing be sure no plans exist to downgrade switch firmware For more information on updating switch firmware see the Switch Module Administrator s Guide and the Switch Module CLI Command Reference in the HP Moonshot Information Library hitp www hp com go moonshot docs Configuring the HP Moonshot System 43 Power capping The HP Moonshot System provides a power capping feature that operates at the chassis level The capping feature can be activated using the iLO CM firmware that runs on each HP Moonshot 1500 chassis After a power cap is set for the chassis all the resident cartridges in the chassis will have the same uniform power cap applied to them until the cap is either modified or canceled With HP APM the enclosure level power capping feature can be expanded without the need to use the iLO CM firmware A global power cap can be applied to all chassis with one HP APM command or different caps can be applied to user defined groups by using flexible zones within the same rack Power capping modes The HP Moonshot 1500 Chassis supports dif
32. each rail until the chassis begins to slide into the rack Then release the Push tabs and continue to slide the chassis into the rack Press and hold the Push tab on each rail again when the rails lock at a 76 2 cm 30 inch extension Then release the Push tabs again and finish sliding the chassis into the rack Failure to release the Push tabs may cause damage to the rails Installing the chassis 24 Installing the blanking panel If the rack rail adapter kit is not installed on the rack always install the blanking panel to ensure proper airflow The blanking panel is not needed when the rack rail adapter kit is installed To install the component 1 For round hole racks remove the guide pins and replace them with the guide pins included for round hole racks Installing the chassis 25 2 Attach a cage nut to each side of the rack jia m we m 3 Align the blanking panel 4 Secure the blanking panel to the rack Installing HP Moonshot System components If components were removed during the chassis installation or additional components were ordered install each device using the procedures in this section If you perform any of the procedures in this section after powering on the chassis ensure proper airflow by ensuring that each bay inside the chassis and at the rear of the chassis is pop
33. ecome unstable WARNING To reduce the risk of personal injury or equipment damage be sure that the rack is adequately stabilized before installing the chassis CAUTION Always plan the rack installation so that the heaviest item is on the bottom of the rack Install the heaviest item first and continue to populate the rack from the bottom to the top CAUTION Be sure to keep the product parallel to the floor when installing the chassis Tilting the product up or down could result in damage to the slides CAUTION HP has not tested or validated the HP Moonshot 1500 Chassis with any third party racks Before installing the HP Moonshot 1500 Chassis in a third party rack be sure to properly scope the limitations of the rack Before proceeding with the installation consider the following e You must fully understand the static and dynamic load carrying capacity of the rack and be sure that it can accommodate the weight of the HP Moonshot 1500 Chassis Be sure sufficient clearance exists for cabling installation and removal of the chassis and actuation of the rack doors Due to the height of the chassis you are required to use one of the following when installing the chassis Rack rail adapter kit Blanking panel A For more information see Determining the chassis rack spacing on page 21 To install the chassis WARNING To reduce the risk of personal injury or damage to the equipment you must fully extend the rail
34. enable No password prompt appears if a password is not configured To configure the Enable password enter the following command Configuring the HP Moonshot System 42 enable password password Updating the switch firmware using the switch console Use TFTP SFTP or SCP to update the switch firmware using the switch console 1 2 3 10 11 12 13 Connect to the switch console Log in to the switch Enter privileged exec mode enable Verify the version of the current switch image show bootvar Verify connectivity by pinging the file server ping X X X X Copy the firmware image from the file server to the alternate firmware bank of the switch copy tftp x x x x lt path_to file gt alternate If using SFTP or SCP copy sftp scp username x x x x lt path_to file gt alternate Verify the version of the new switch image show bootvar Configure the switch to boot from the alternate flash file system boot system alternate Reset the switch to boot from the new image reload Traffic is halted on the associated switch The switch boots from the alternate flash file system The image is loaded and runs in the primary flash file system Verify the firmware update was successful show bootvar Update the boot loader on the switch update bootcode Update the CPLDs on the switch Z NOTICE The CPLD update halts network traffic on the associated switch Once initiated do not interrupt th
35. ferent power capping modes The setting impacts how the chassis reacts to changes in power supply functionality such as loss of input power to a power supply or failure or removal of a power supply from the system Selecting the appropriate power capping mode depends on system requirements how the chassis is provisioned and how power feeds are supplied The power capping mode alone does not guarantee availability in the event of power loss The chassis requires at least two power supplies The type and number of power supplies depends on the cartridges installed in the chassis The following power capping modes are standard and are configurable in the power management controller e Mode O No Redundancy All power capping is disabled This mode may be used to minimize any possible performance impact of power capping logic e Mode 1 Max Performance with Redundancy This is the default power capping mode This mode allows the maximum number of nodes to run by engaging power capping if the power draw from the chassis attempts to exceed the load supported by the active power supplies In this mode the system is expected to survive an unexpected power loss to one of the power supplies e Mode 2 Full AC DC Redundancy Mode Power capping is enforced such that system has N 1 power redundancy In this mode the system should see no performance degradation due to a power supply loss Configuring a power cap To configure power capping for the HP Mo
36. ght cause radio or television interference However HP does not guarantee that the system does not interfere with radio and television reception Take these precautions e Use only shielded cables e Install and route the cables according to the instructions provided e Ensure that all cable connector screws are firmly tightened e Use only HP supported peripheral devices e Before system operation ensure that all panels and cover plates are in place and secure Regulatory information 48 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system be aware of the precautions you need to follow when setting up the system or handling parts A discharge of static electricity from a finger or other conductor may damage system boards or other static sensitive devices This type of damage may reduce the life expectancy of the device To prevent electrostatic damage Avoid hand contact by transporting and storing products in static safe containers Keep electrostatic sensitive parts in their containers until they arrive at static free workstations Place parts on a grounded surface before removing them from their containers Avoid touching pins leads or circuitry Always be properly grounded when touching a static sensitive component or assembly Grounding methods to prevent electrostatic discharge Several methods are used for grounding Use one or more of the following methods when handling or ins
37. he HP Technical Support Center and a technician will help you over the telephone HP specifies in the materials shipped with a replacement CSR part whether a defective part must be returned to HP In cases where it is required to return the defective part to HP you must ship the defective part back to HP within a defined period of time normally five 5 business days The defective part must be returned with the associated documentation in the provided shipping material Failure to return the defective part may result in HP billing you for the replacement With a customer self repair HP will pay all shipping and part return costs and determine the courier carrier to be used For more information about HP s Customer Self Repair program contact your local service provider For the North American program refer to the HP website http www hp com go selfrepair R paration par le client CSR Les produits HP comportent de nombreuses pi ces CSR Customer Self Repair r paration par le client afin de minimiser les d lais de r paration et faciliter le remplacement des pi ces d fectueuses Si pendant la p riode de diagnostic HP ou ses partenaires ou mainteneurs agr s d termine que la r paration peut tre effectu e l aide d une pi ce CSR HP vous l envoie directement Il existe deux cat gories de pi ces CSR Obligatoire Pi ces pour lesquelles la r paration par le client est obligatoire Si vous demandez HP de remplacer ces
38. iew To set up and install the chassis Unpack the Moonshot System Unpacking the HP Moonshot System on page 21 Determine the chassis rack spacing Determining the chassis rack spacing on page 21 Install the rack rails Installing the rack rails on page 21 Install the chassis in the rack Installing the chassis in the rack on page 21 Install the blanking panel Installing the blanking panel on page 25 Ph de ge p o Install Moonshot System components Installing HP Moonshot System components on page 26 Unpacking the HP Moonshot System Unpack the following hardware and prepare for installation e HP Moonshot System e Accessory kit e Quick Deploy Rail System Kit e Blanking panel Determining the chassis rack spacing Up to seven chassis can be installed in a 36U 1200 mm 47 24 in deep rack If installing more than one chassis install the first chassis in the bottom of the rack and then install additional chassis by moving up the rack with each subsequent chassis Due to the height of the Moonshot 1500 Chassis chassis installation requires either the use of a rack rail adapter kit or a blanking panel If you ordered a rack rail adapter kit to be installed at the factory then the blanking panel is not required If the rack rail adapter kit was not installed then install the blanking panel directly above the chassis For more information see Installing the blanking panel on page 25 Installing the rack
39. in the HP Moonshot Information Library http www hp com go moonshot docs Software prerequisites Before setting up and configuring the HP Moonshot System be prepared to do the following Obtain a supported operating system For information about operating systems supported by the Moonshot System see the operating system support matrices http www hp com go supportos For deployment procedures see operating system deployment documentation in the HP Moonshot Information Library http www hp com go moonshot docs Prepare to update firmware and system software components using HP Moonshot Component Pack HP Moonshot Component Pack is a comprehensive firmware solution tested on the HP Moonshot System and delivered as a compressed file The compressed file includes all the component files needed to update a Moonshot System Users deploy the firmware updates contained in the Moonshot Component Pack from a command line by using the iLO Chassis Manager CLI or HP Moonshot 45G 180G Switch Module CLI or by using the included HP Smart Update Manager Download the latest pack from the HP website http www hp com go moonshot download For a complete list of Moonshot System documentation see the HP Moonshot Information Library http www hp com go moonshot docs Determine power and cooling configurations Validate power and cooling reguirements based on location and installed components For more information see the HP Moonshot Syste
40. k might become unstable WARNING The chassis is very heavy To reduce the risk of personal injury or damage to the equipment do the following e Observe local occupational health and safety requirements and guidelines for manual material handling e Get help to lift and stabilize the product during installation or removal especially when the product is not fastened to the rails The chassis weighs more than 81 65 kg 180 00 lb so at least four people must lift the chassis into the rack together An additional person may be required to help align the chassis if the chassis is installed higher than chest level WARNING To reduce the risk of personal injury or damage to the equipment you must adequately support the chassis during installation and removal WARNING Be sure to install the chassis starting from the bottom of the rack and then work your way up the rack WARNING To reduce the risk of personal injury from hot surfaces allow the drives and the internal system components to cool before touching them WARNING To reduce the risk of electric shock or damage to the equipment e Never reach inside the chassis while the system is powered up e Perform service on system components only as instructed in the user documentation CAUTION Always be sure that equipment is properly grounded and that you follow proper grounding procedures before beginning any installation procedure Improper grounding can result in ESD damage to e
41. lectronic components For more information refer to Electrostatic discharge on page 49 CAUTION When performing non hot plug operations you must power down the chassis and or the system However it may be necessary to leave the chassis powered up when performing other operations such as hot plug installations or troubleshooting Space and airflow requirements To enable servicing and ensure adequate airflow observe the following spatial requirements when deciding where to install a rack Leave a minimum clearance of 121 9 cm 48 0 in in front of the rack Leave a minimum clearance of 76 2 cm 30 0 in in back of the rack Leave a minimum clearance of 121 9 cm 48 0 in from the back of the rack to the rear of another rack or row of racks Planning the installation 7 HP rack products draw cool air in through the front and expel warm air through the rear of the enclosure Therefore the front of the rack enclosure must be adequately ventilated to enable ambient room air to enter the enclosure and the rear of the enclosure must be adequately ventilated to enable the warm air to escape from the enclosure We IMPORTANT Do not block the ventilation openings If the front of the rack is not completely filled with components the remaining gaps between the components can cause changes in the airflow which can adversely affect cooling within the rack Cover these gaps with blanking panels AN CAUTION Always use blanking panels
42. m Configuration and Compatibility Guide in the HP Moonshot Information Library http www hp com go moonshot docs Power requirements Installation of this equipment must comply with local and regional electrical regulations governing the installation of IT equipment by licensed electricians This equipment is designed to operate in installations Planning the installation 5 covered by NFPA 70 1999 Edition National Electric Code and NFPA 75 1992 code for Protection of Electronic Computer Data Processing Equipment For electrical power ratings on options refer to the product rating label or the user documentation supplied with that option N WARNING To reduce the risk of personal injury fire or damage to the equipment do not overload the AC supply branch circuit that provides power to the rack Consult the electrical authority having jurisdiction over wiring and installation requirements of your facility A CAUTION Protect the chassis from power fluctuations and temporary interruptions with a regulating UPS This device protects the hardware from damage caused by power surges and voltage spikes and keeps the chassis in operation during a power failure HP Advanced Power Manager HP APM is a point of contact for system administration To install configure and access HP APM see the HP Proliant SL Advanced Power Manager User Guide in the HP Moonshot Information Library http www hp com go moonshot docs Hot plug power suppl
43. m go selfrepair Customer Self Repair HP Produkte enthalten viele CSR Teile Customer Self Repair um Reparaturzeiten zu minimieren und h here Flexibilit t beim Austausch defekter Bauteile zu erm glichen Wenn HP oder ein HP Servicepartner bei der Diagnose feststellt dass das Produkt mithilfe eines CSR Teils repariert werden kann sendet Ihnen HP dieses Bauteil zum Austausch direkt zu CSR Teile werden in zwei Kategorien unterteilt Zwingend Teile f r die das Customer Self Repair Verfahren zwingend vorgegeben ist Wenn Sie den Austausch dieser Teile von HP vornehmen lassen werden Ihnen die Anfahrt und Arbeitskosten f r diesen Service berechnet Optional Teile f r die das Customer Self Repair Verfahren optional ist Diese Teile sind auch f r Customer Self Repair ausgelegt Wenn Sie jedoch den Austausch dieser Teile von HP vornehmen lassen m chten k nnen bei diesem Service je nach den f r Ihr Produkt vorgesehenen Garantiebedingungen zus tzliche Kosten anfallen HINWEIS Einige Teile sind nicht f r Customer Self Repair ausgelegt Um den Garantieanspruch des Kunden zu erf llen muss das Teil von einem HP Servicepartner ersetzt werden Im illustrierten Teilekatalog sind diese Teile mit No bzw Nein gekennzeichnet Support and other resources 53 CSR Teile werden abh ngig von der Verf gbarkeit und vom Lieferziel am folgenden Gesch ftstag geliefert Fir bestimmte Standorte ist eine Lieferung am selben Tag oder
44. n accordance with any regional or national electrical wiring codes such as the International Electrotechnical Commission IEC Code 364 parts 1 through 7 Furthermore you must be sure that all power distribution devices used in the installation such as branch wiring and receptacles are listed or certified groundingtype devices Because of the high ground leakage currents associated with this equipment HP recommends the use of a PDU that is either permanently wired to the building s branch circuit or includes a nondetachable cord that is wired to an industrial style plug NEMA locking style plugs or those complying with IEC 60309 are considered suitable for this purpose Using common power outlet strips to supply power to this equipment is not recommended Planning the installation 8 Identifying components and LEDs HP Moonshot System components Description Switch module Uplink module Moonshot 1500 CM module Power supplies The quantity depends on the configuration ordered The following documents also ship with the Moonshot System e Start Here for Important Setup Information e Safety Compliance and Warranty Information Identifying components and LEDs 9 Chassis front panel components 833328322883 288 Ol O pcs Ge SSS minie O zs P JO Flashing Green The chassis is waiting to power on Green Normal operation
45. n the uplink module Configure the terminal with the following settings o 115200 baud rate o 8 data bits o No parity o 1 stop bit o No flow control Start the terminal The switch login prompt appears Enter admin No password is set by default Obtain the switch management IP address To access the switch console remotely the iLO CM management port must be connected to a network If DHCP services are provided on the network obtain the switch management IP address In 2 Access the switch CLI interface locally Enter privileged exec mode At the switch prompt enter enable Show the switch management IP address At the privileged exec prompt enter show serviceport If DHCP services are not available configure the serviceport IP address Be sure to configure the enable password before managing the switch remotely To configure the switch see the Switch Administrator s Guide and the Switch CLI Command Reference in the HP Moonshot Information Library http www hp com go moonshot docs Contigure the Enable password The Enable password controls access to the privileged exec mode The default authentication profile denies remote access to the privileged exec mode if the Enable password is not configured Configure the Enable password before starting a remote session To configure the password 1 2 Access the CLI locally on page 42 To access the privileged exec mode enter the following command
46. ngende CSR onderdeel of het defecte onderdeel aan HP moet worden geretourneerd Als het defecte onderdeel aan HP moet worden teruggezonden moet u het defecte onderdeel binnen een bepaalde periode gewoonlijk vijf 5 werkdagen retourneren aan HP Het defecte onderdeel moet met de bijbehorende documentatie worden geretourneerd in het meegeleverde verpakkingsmateriaal Als u het defecte onderdeel niet terugzendt kan HP u voor het vervangende onderdeel kosten in rekening brengen Bij reparatie door de klant betaalt HP alle verzendkosten voor het vervangende en geretourneerde onderdeel en kiest HP zelf welke koerier transportonderneming hiervoor wordt gebruikt Neem contact op met een Service Partner voor meer informatie over het Customer Self Repair programma van HP Informatie over Service Partners vindt u op de HP website hitp www hp com go selfrepair Reparo feito pelo cliente Os produtos da HP s o projetados com muitas pe as para reparo feito pelo cliente CSR de modo a minimizar o tempo de reparo e permitir maior flexibilidade na substitui o de pe as com defeito Se durante o per odo de diagn stico a HP ou fornecedores parceiros de servico da HP concluir que o reparo pode ser efetuado pelo uso de uma pe a CSR a pe a de reposi o ser enviada diretamente ao cliente Existem duas categorias de pecas CSR Obrigat ria Pecas cujo reparo feito pelo cliente obrigat rio Se desejar que a HP substitua essas pecas ser o cob
47. nshot Information Library http www hp com go moonshot docs Cabling the HP Moonshot System 38 Configuring the HP Moonshot System Chassis contiguration overview To configure the HP Moonshot System complete the following Configure the chassis on page 39 Configure the switch on page 41 Configure the chassis To configure the Moonshot 1500 chassis complete the following steps 1 uk won Connect and configure a terminal for chassis configuration on page 39 Log in to the iLO CM firmware on page 40 Obtain the MAC addresses for each cartridge node on page 40 Configure the iLO CM firmware administrator account password on page 40 Update the firmware for the HP Moonshot System components on page 40 For detailed configuration information see the following documents in the HP Moonshot Information Library http www hp com go moonshot docs o o HP Moonshot iLO Chassis Management CLI User Guide HP Moonshot System Configuration and Compatibility Guide Connect and configure a terminal for chassis configuration To connect and configure a terminal to communicate with the iLO CM firmware 1 Use a serial cable to connect a PC or terminal to the iLO CM management serial port on the Moonshot 1500 CM module To locate the iLO CM management serial port see HP Moonshot 1500 Chassis Management module components on page 16 Configure the terminal with the following settings o o o
48. nt Pack download website http www hp com go moonshot download Installing the switch module AN CAUTION To avoid connectivity loss do not remove switches already in operation Installing the chassis 33 To install the component Locate the switch module slot and then remove the blank LA Prepare the switch module for installation 2 Installing the chassis 34 3 Align and install the switch module into the chassis 4 Do one of the following o If the uplink module is already installed verify the switch module powers on and the health LED is green o If the uplink module is not installed install the uplink module before verifying LEDs For more information see Switch information and guidelines on page 29 Install the access panel and then return the chassis to the rack 6 After both components have been installed verify the switch firmware is at the HP recommended firmware version For more information see the HP Moonshot Component Pack download website http www hp com go moonshot download Installing the chassis 35 Cabling the HP Moonshot System Cabling overview A WARNING To reduce the risk of electric shock or injury due to high current electrical energy be sure that all power is completely disconnected at the source before beginning any power connections to the power bus bars or power bus box WARNING Be sure that all circuit breakers are locked in the off position before
49. onshot System use the HP Moonshot iLO Chassis Management Firmware The iLO CM firmware is a single point of access for chassis management for the HP Moonshot 1500 Chassis For more information see the HP Moonshot iLO Chassis Management User Guide on the HP website http www hp com go moonshot docs Setting the chassis power cap mode using iLO CM firmware To set the power cap 1 Log in to the iLO CM firmware on page 40 2 Enter the following command to review the current power capacity mode for the chassis show chassis power Configuring the HP Moonshot System 44 Example hpiLO gt show chassis power Chassis Power in use 170 Watts Power Capacity 1818 Watts Status OK Powercap Mode Max Performance with Redundancy Enter the following command to set the power capacity mode for the chassis set chassis powercap mode 0 1 2 Example hpiLO gt set chassis powercap mode 2 Set powercap mode to Full AC DC Redundancy Mode Configuring the HP Moonshot System 45 Troubleshooting Troubleshooting resources The HP Moonshot System Troubleshooting Guide provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification issue resolution and software maintenance on the HP Moonshot System The document is available in the HP Moonshot Information Library http www hp com go moonshot docs Troubleshooting 46 Regulatory information Safety and regul
50. orized reseller 51 backplane assembly release lever 10 battery replacement notice 5 bay numbering fan 12 bay numbering power supply 12 bay numbering uplink module 13 before you contact HP 51 Belarus Kazakhstan Russia marking 47 bezelear 10 blanking panels 25 BSMI notice 5 C cable management arm 38 cable management arm installing 38 cabling 36 Canadian notice 5 cartridge blank 9 cartridge health LED 10 19 cartridge installation 29 cartridge MAC address obtaining 40 cartridge slot numbering 18 cartridges 9 cautions 6 chassis components 9 10 11 17 18 chassis configuration 39 chassis environmental specifications 50 chassis health LED 10 chassis power LED 10 chassis specifications 50 chassis UID LED button 10 chassis install in rack 21 CLI accessing 42 compiling documentation 6 compliance 5 components 9 10 11 16 17 29 components identification 9 10 configuration 39 configuration of system 39 configuration chassis 39 configuration power 5 configuration switch 41 configure a terminal 39 configuring a power cap 44 configuring the chassis 39 connecting a serial cable to a laptop 39 connecting an Ethernet cable 36 connecting to the network 36 37 contact information 51 contacting HP 51 cooling power configuring 5 CSR customer self repair 51 customer self repair CSR 51 D data center management network 36 data center production network 37 Declaration of Conformity 47
51. radas as despesas de transporte e m o de obra do servico Support and other resources 55 Opcional Pe as cujo reparo feito pelo cliente opcional Essas pe as tamb m s o projetadas para o reparo feito pelo cliente No entanto se desejar que a HP as substitua pode haver ou n o a cobran a de taxa adicional dependendo do tipo de servi o de garantia destinado ao produto OBSERVA O Algumas pe as da HP n o s o projetadas para o reparo feito pelo cliente A fim de cumprir a garantia do cliente a HP exige que um t cnico autorizado substitua a pe a Essas pe as est o identificadas com a marca No N o no cat logo de pe as ilustrado Conforme a disponibilidade e o local geogr fico as pe as CSR ser o enviadas no primeiro dia til ap s o pedido Onde as condi es geogr ficas permitirem a entrega no mesmo dia ou em quatro horas pode ser feita mediante uma taxa adicional Se precisar de aux lio entre em contato com o Centro de suporte t cnico da HP para que um t cnico o ajude por telefone A HP especifica nos materiais fornecidos com a pe a CSR de reposi o se a pe a com defeito deve ser devolvida HP Nos casos em que isso for necess rio preciso enviar a pe a com defeito HP dentro do per odo determinado normalmente cinco 5 dias teis A pe a com defeito deve ser enviada com a documenta o correspondente no material de transporte fornecido Caso n o o fa a a HP poder cobrar a reposi o Par
52. revisto per il prodotto NOTA alcuni componenti HP non sono progettati per la riparazione da parte del cliente Per rispettare la garanzia HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato Tali parti sono identificate da un No nel Catalogo illustrato dei componenti In base alla disponibilit e alla localit geografica le parti CSR vengono spedite con consegna entro il giorno lavorativo seguente La consegna nel giorno stesso o entro quattro ore offerta con un supplemento di costo solo in alcune zone In caso di necessit si pu richiedere l assistenza telefonica di un addetto del centro di supporto tecnico HP Nel materiale fornito con una parte di ricambio CSR HP specifica se il cliente deve restituire dei componenti Qualora sia richiesta la resa ad HP del componente difettoso lo si deve spedire ad HP entro un determinato periodo di tempo generalmente cinque 5 giorni lavorativi Il componente difettoso deve essere restituito con la documentazione associata nell imballo di spedizione fornito La mancata restituzione del componente pu comportare la fatturazione del ricambio da parte di HP Nel caso di riparazione da parte del cliente HP sostiene tutte le spese di spedizione e resa e sceglie il corriere vettore da utilizzare Per ulteriori informazioni sul programma CSR di HP contattare il centro di assistenza di zona Per il programma in Nord America fare riferimento al sito Web HP http www hp co
53. rt the following pluggable Ethernet transceiver modules e HP 4OGBASE QSFP e HP 40GBASE QSFP SR4 e HP 40GBASE QSFP DAC e HP 40GBASE QSFP to 4x10G SFP Any available port can be used to connect to the data center Ensure the port is populated with supported HP transceiver modules that are compatible with the data center port type Moonshot 4QSFP Uplink Module LEDs and buttons O mE Identifying components and LEDs 15 fom Dempes mm Uplink module UID Solid blue Switch module ID is selected LED button Flashing blue Switch module firmware update is in progress Off Switch module ID is not selected Uplink module health Green Normal operation Flashing amber Degraded condition Flashing red Critical condition Off No power 3 Uplink module link Solid green Link LED Off No link Uplink module Flashing green Activity activity LED Off No activity Reset button Resets the switch module label RCM Moonshot 1500 CM module diagnostic port iLO CM management serial port Moonshot 1500 CM module USB connector Moonshot 1500 CM module MicroSD slot Identifying components and LEDs 16 HP Moonshot 1500 Chassis Management module LEDs and buttons CMC oo 1 LO CM management port link LED LO MGMT LO CM management port activity LED LO CM link port link LED LO CM link port activity LED Moonshot 1500 CM module UID LED button
54. s To fully extend the rails press the push tabs and extend the rails until the rails click twice Installing the chassis 22 1 Fully extend the rails by pressing the push tabs and extending the rails until the rails click two times WARNING To reduce the risk of personal injury or equipment damage be sure that the rack is adequately stabilized before installing the chassis WARNING The chassis is very heavy To reduce the risk of personal injury or damage to the equipment e Always use either a lift that can handle the load of the product or at least four people to lift and stabilize the product pieces during assembly installation or removal especially when the chassis is not installed in the rack An additional person may be required to help align the chassis if the chassis is installed higher than chest level e Observe local occupational health and safety requirements and guidelines for manual material handling e HP recommends removing all installed components from the chassis before installing or moving the chassis AN CAUTION Be sure to keep the product parallel to the floor when installing the chassis Tilting the product up or down could result in damage to the rails Installing the chassis 23 2 Install the chassis into the J slot on the rails and then pull it forward 3 Push in the release lever and then install the chassis into the rack A CAUTION Press and hold the Push tab on
55. s on page 29 Removing the uplink module blank on page 32 Installing the uplink module on page 32 Installing the switch module on page 33 Switch information and guidelines Before installing the components review the following guidelines Installing the chassis 29 e Always install the switch module and the uplink module in corresponding bays Both components must be installed for normal operation e The switch module and the uplink module can be installed in any order e The switch module and the uplink module power down when either module is removed from the chassis e The switch module and the uplink module power up after both modules are installed in the chassis e Removing any component from bay A or bay B does not disrupt traffic for the other switch assembly e For the most current product information see the release notes in the HP Moonshot Information Library http www hp com go moonshot docs e Always use the HP recommended firmware version For more information on HP recommended firmware versions see the HP Moonshot Component Pack download website http www hp com go moonshot download e The first NIC port discovered by the operating system routes traffic through switch A The second NIC port discovered by the operating system routes traffic through switch B Installing the chassis 30 Production network mapping nemi E
56. socios de servicio de HP identifica que una reparaci n puede llevarse a cabo mediante el uso de un componente CSR HP le enviar dicho componente directamente para que realice su sustituci n Los componentes CSR se clasifican en dos categor as e Obligatorio componentes para los que la reparaci n por parte del usuario es obligatoria Si solicita a HP que realice la sustituci n de estos componentes tendr que hacerse cargo de los gastos de desplazamiento y de mano de obra de dicho servicio e Opcional componentes para los que la reparaci n por parte del usuario es opcional Estos componentes tambi n est n dise ados para que puedan ser reparados por el usuario Sin embargo si precisa que HP realice su sustituci n puede o no conllevar costes adicionales dependiendo del tipo de servicio de garant a correspondiente al producto NOTA Algunos componentes no est n dise ados para que puedan ser reparados por el usuario Para que el usuario haga valer su garant a HP pone como condici n que un proveedor de servicios autorizado realice la sustituci n de estos componentes Dichos componentes se identifican con la palabra No en el cat logo ilustrado de componentes Seg n la disponibilidad y la situaci n geogr fica los componentes CSR se enviar n para que lleguen a su destino al siguiente d a laborable Si la situaci n geogr fica lo permite se puede solicitar la entrega en el mismo d a o en cuatro horas con un coste adicional
57. talling electrostatic sensitive parts Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis Wrist straps are flexible straps with a minimum of 1 megohm 10 percent resistance in the ground cords To provide proper ground wear the strap snug against the skin Use heel straps toe straps or boot straps at standing workstations Wear the straps on both feet when standing on conductive floors or dissipating floor mats Use conductive field service tools Use a portable field service kit with a folding static dissipating work mat If you do not have any of the suggested equipment for proper grounding have an authorized reseller install the part For more information on static electricity or assistance with product installation contact an authorized reseller Electrostatic discharge 49 Specifications Chassis environmental specifications Temperature range J 10 C to 35 C 50 F to 95 F Maximum Wet Maximum Wet bulb temperature temperature Operating ema 82 4 F EE Relative humidity non condensing 10 to 90 5 to 95 All temperature ratings shown are for sea level An altitude derating of 1 C per 304 8 m 1 8 F per 1000 ft to 3048 m 10 000 ft is applicable No direct sunlight allowed Upper operating limit is 3 048 m 10 000 ft or 70 kPa 10 1 psia Upper non operating limit is 9 144 m 30 000 ft Storage maximum humidity of 95 is based
58. test firmware version from the HP Moonshot Component Pack download site http www hp com go moonshot download 3 After downloading the firmware image upload all files to the iLO CM firmware repository add firmware file lt source URL gt 4 Verify the images were uploaded successfully show firmware files 5 Update the iLO CM firmware or system firmware update firmware lt filename gt 6 Update the cartridge firmware o Single cartridge update firmware lt filename gt C lt x gt o All cartridges update firmware lt filename gt all For more information on updating the firmware see the HP Moonshot iLO Chassis Management CLI User Guide in the HP Moonshot Information Library http www hp com go moonshot docs Configure the switch To configure the Moonshot switch complete the following steps 1 Access the CLI locally on page 42 2 Obtain the switch management IP address 3 Configure the Enable password on page 42 4 Update the switch firmware through the switch console Update the firmware for the HP Moonshot System components on page 40 Configuring the HP Moonshot System 41 For detailed configuration information see the Switch Administrator s Guide and Switch CLI Guide in the HP Moonshot Information Library http www hp com go moonshot docs Access the CLI locally To access the CLI interface locally ls 2 Use a console cable to connect a PC or terminal to the serial console port o
59. tion Off No power 3 Drive LED Green Activity Off No activity 4 Cartridge UID LED button Blue Cartridge ID is selected Flashing blue Cartridge firmware update is in progress Off Cartridge ID is not selected 5 Cartridge link Flashing white Cartridges are linked LED button Off Cartridge is not linked to other cartridges Depending on the cartridge installed there might be 0 1 or 2 drive LEDs The cartridge link LED flashes for 10 seconds after the link button is pressed Identifying components and LEDs 19 Switch module button sensor and LEDs Switch module power Green Normal operation Amber Standby operation Off No power Switch module health LED Switch module uplink activity LED Switch module downlink activity LED Switch module UID LED button Access panel sensor Detects the presence of the access panel Green Normal operation Flashing amber Degraded condition Flashing red Critical condition Off No power Green Link Flashing green Activity Off No activity Green Link Flashing green Activity Off No activity Solid blue Switch module ID is selected Flashing blue Switch module firmware update is in progress Off Switch module ID is not selected The fan speed adjusts automatically when the access panel is installed or removed Identifying components and LEDs 20 Installing the chassis Installation overv
60. ulated with either a component or a blank For component specific replacement information see the HP Moonshot 1500 Chassis Installing the chassis 26 Maintenance and Service Guide or cartridge specific user and maintenance guides in the HP Moonshot Information Library http www hp com go moonshot docs Installing the Moonshot 1500 CM module Install the component as indicated Installing a power supply A WARNING To reduce the risk of electric shock or damage to the equipment e Do not disable the power cord grounding plug The grounding plug is an important safety feature e Plug the power cord into a grounded earthed electrical outlet that is easily accessible at all times e Unplug the power cord from the power supply to disconnect power to the equipment e Do not route the power cord where it can be walked on or pinched by items placed against it Pay particular attention to the plug electrical outlet and the point where the cord extends from the server Installing the chassis 27 To install the component Install the power supply into the device bay and then press firmly until the power supply is seated Installing the fans Install the component as indicated Installing the chassis 28 Installing the cartridge To install the component 1 2 Prepare the cartridge Align and install the cartridge into the chassis Installing network components Switch information and guideline
61. y calculations For hot plug power supply specifications and calculators to determine electrical and heat loading for the HP Moonshot System see the HP Power Advisor on the HP website http www hp com go hppoweradvisor Compiling the documentation The documentation while delivered individually and in various formats works as a system Consult these documents before attempting installation These documents provide required important safety information and decision making steps for configuration The HP Moonshot System information can be found in the HP Moonshot Information Library http www hp com go moonshot docs e Quick Deploy Rail System Installation Instructions e HP Moonshot System Site Planning Guide e HP Moonshot iLO Chassis Management CLI User Guide e Links to all related documentation e Videos Warnings and cautions A WARNING To reduce the risk of personal injury or damage to equipment heed all warnings and cautions throughout the installation instructions Planning the installation 6 gt Db D gt WARNING To reduce the risk of personal injury or damage to the equipment be sure that e The rack is bolted to the floor using the concrete anchor kit e The leveling feet extend to the floor e The full weight of the rack rests on the leveling feet e The racks are coupled together in multiple rack installations e Only one component is extended at a time If more than one component is extended a rac

HP Moonshot 1500 Chassis Installation Manual

Contents

Download Pdf Manuals

Related Search

Related Contents