Home

HP CM1415fn Reference Guide

1. The Finishing tab contains the following controls e Document Options Document preview image e Orientation Document Options The Document Options group box contains the following controls e Print on Both Sides ENWW Finishing tab features 85 e Flip Pages Up e Booklet Layout e Pages per Sheet e Print Page Borders e Page Order Print on Both Sides NOTE This feature is called Print on Both Sides manually for the HP LaserJet Pro CM1415 and the HP LaserJet Pro CM1415fn because these models do not include an automatic duplex unit For all other product models this feature is called Print on Both Sides The default setting for the Print on Both Sides option is off not selected Print on Both Sides is available when the following conditions exist e Paper type on the Paper tab is set to any paper type except for the following types o Labels o Color Laser Transparency e Paper sizes is set to any paper size except for the following sizes o Envelope 10 gt Double Postcard JIS Envelope 9 o Envelope Monarch gt Envelope B5 o Envelope C5 o gt Envelope C6 o Envelope DL Print on both sides manually Select the Print on Both Sides Manually check box to print on the second side of the paper for the HP LaserJet Pro CM1415 and HP LaserJet Pro CM1415fn product models which do not have a duplexing unit installed Also select Print on Both Sides Manually on the other HP LaserJet
2. Black in wrong position Description The print cartridge is installed in the incorrect slot Recommended action Make sure that each print cartridge is installed in the correct slot From front to back the print cartridges are installed in this order black cyan magenta and yellow Black Very Low ENWW Description The print cartridge is at the end of its useful life and the At Very Low menu item in the System Setup menu is set to Continue Recommended action To ensure optimal print quality HP recommends replacing the print cartridge at this point You can continue printing until you notice a decrease in print quality Actual cartridge life may vary Once an HP supply has reached very low HP s premium Protection Warranty on that supply has ended All print defects or cartridge failures incurred when an HP supply is used in continue at very low Tools for troubleshooting 153 mode will not be considered to be defects in materials or workmanship in the supply under the HP Print Cartridge Warranty Statement 154 Chapter 6 Solve problems ENWW Canceled scan Clear document Description A page might be jammed in the document feeder You touched the Cancel X button while scanning faxing or copying to cancel the current job while pages were feeding from the document feeder The cancel process does not automatically clear the document feeder Recommended action Remove the jammed item Then clear the items in the
3. Index 257 R Readiris software file types supported 29 Windows 17 receiving faxes error report printing 219 log HP ToolboxFX 128 receiving faxes troubleshooting 206 regional versions CD 9 removing Macintosh software 118 repetitive defects troubleshooting 187 reports configuration page 134 demo page 134 diagnostics page 134 error 168 202 fax 146 menumap 134 network report 134 PCL 6 font list 134 PCL font list 134 print quality page 134 PS font list 134 service 202 service page 134 supplies status page 134 usage page 134 reports fax error 219 printing all 217 resets NVRAM initialization 204 restoring default settings 204 NVRAM initialization 204 restoring factory set defaults 203 RFU See remote firmware updates rollers repetitive image defects 187 RTF files viewing 3 S scan methods 28 Scan Driver using 28 258 Index WIA 34 Windows 17 Scan software 29 scanner glass cleaning scanning HP Scan software 29 WIA driver features 34 secondary service menu 202 sending faxes error report printing 219 log HP ToolboxFX 128 sending faxes troubleshooting 210 Service menu secondary 202 settings continuous export 25 drivers Macintosh 114 factory set defaults restoring 203 HP ToolboxFX 129 locking 25 parameters fax data store 244 189 190 priority 113 Setup Wizard fax 35 software HP LaserJet Utility 114 Macintosh 114 settings 113 supported operating system
4. Menu item Sub menu item Sub menu item Description Print Report Now Prints a list of all the individual and group dial entries in the phone book Change Defaults Opens the Fax Setup menu Scan Menu Menu item Description Scan to USB Drive Scans a document and stores it as a PDF file or JPEG image on the USB flash drive ENWW Tools for troubleshooting 149 USB Flash Drive The following types are supported e PDF e JPG Menu item Description Print Documents Prints documents stored on the USB drive Use the arrow buttons to scroll through the documents Touch the names of documents that you want to print Touch the summary screen to change settings such as the number of copies the paper size or the paper type Touch the Print button when you are ready to print the documents View and Print Photos Previews photos on the USB drive Use the arrow buttons to scroll through the photos Touch the preview image for each photo that you want to print You can adjust the settings and you can save the changes as the new default settings When you are ready to print the photos touch the Print button Scan to USB Drive Scans a document and stores it as a PDF file or JPEG image on the USB flash drive 150 Chapter 6 Solve problems ENWW Interpret control panel messages Control panel message types Alert and warning messages appear temporarily and might require you to acknowledge the message by touching
5. Solve fax problems 207 208 Table 6 4 Fax receive error codes continued Error code Description Solution 243 and 244 One of the following has occurred e The user of the remote product has touched the Cancel X button causing the session to be prematurely terminated e The sending fax product determined there was a feature incompatibility between the two products and has terminated the session An example would be when the receiving product wanted to initiate polling but the sending product did not support this mode of operation 1 Confirm that the sender is not inadvertently attempting to poll transmit from the receiving product instead of transmitting to the receiving product This mode of operation must be specially configured on the receiving product If poll transmission from the receiving product is the desired mode of operation confirm that the receiving product has been configured for this operation 2 Reconfigure the receiving fax product fo use different configuration settings toggle the ECM state and or select a slower reception speed 245 and 246 ECM error The user of the sending product has touched the Cancel button causing the session to be prematurely terminated The receiving product has been holding off the remote product during reception of a large and or complex document due to lack of available memory This hold off time has exceeded the timeout typically 60 sec
6. Unable to use fax functions from the control panel The product might be password protected Use the HP Embedded Web Server HP Toolbox software or the control panel to set a password If you do not know the password for the product contact your system administrator Verify with the system administrator that the fax functionality has not been disabled 224 Chapter 6 Solve problems ENWW Unable to use speed dials e Make sure that the fax number is valid e If an outside line requires a prefix turn on the Dia Prefix option or include the prefix in the speed dial number From the Home screen touch the Setup button Open the Fax Setup menu c Open the Basic Setup menu d Open the Dia Prefix menu e Select the On setting Unable to use group dials e Make sure that the fax number is valid e If an outside line requires a prefix turn on the Dial Prefix option or include the prefix in the speed dial number a From the Home screen touch the Setup N button Open the Fax Setup menu c Open the Basic Setup menu d Open the Dia Prefix menu e Select the On setting e Set up all entries in the group with speed dial entries a Open an unused speed dial entry b Enter the fax number for the speed dial c Touch the OK button to save the speed dial Receive a recorded error message from the phone company when trying to send a fax e Make sure you dial the fax number correctly and make sure that the phone ser
7. Default watermark settings s munsersunnsaietonmnne Mn mus siucantionmoneimbaengauies 83 EO 1G R E EEEE Su cet O E nity ins bun E ea nh tonal rsonen otic ameanohites 85 Document Options cree ceciy Si E E daeoesd ia R E ete eines Coes aa seen ae eater eeaeetens 85 Pritt te Both Sides skins rnnehiobionmabacdhveomiitisesureladeoesouncueteuromeanskenp tons 86 ENWW Print on both sides manually ssc c yioesevnssy eee varied oe eae ueedseded 86 Flip Pies sl ir sis adeno oasnoetsenule nanos anes at aud orautiiua tenn Reacts jal madvemedesn negtane deltas 88 Booker Layout nonien A det nes Soea Alda ie ated dat 89 Book and Booklet Printing ssn ytacontsieiicsneeir tinned dine Watsanctaatels 89 Pages per SHEET cat ten eiae i aae a a A a 90 Print Page Borders cuian a a E E Oa 90 Page COREE mensi a e a ae aa eaa eiat 90 Document preview IMAQE cceccececcceaeeeeeeeseeeeeeceeececcececeeeeeeaaeeaaeeeseeeeeeesereeeeeeeeseneas 90 Orientations ss enee eea EEEE NIN AA raa S E A TE RATER date 91 EIA E AE T EA A E ee 92 Color ORONS o A EE ceca E EEEE EE E A RS 93 Automatic aspan e ET n di ENa a N a ATE 93 Manval sse E a E E E a E E E E nee eee 93 Neutral Grays sikina ETR AT A T EA 94 Color MNEMES scere tet xan E EA E T E cats 94 DIE OIA sRGB E EEE EEE E E ET 94 Photo SRGB agan a n E TA a A A OTANTA 94 Pht Adobe RGB 998 eiiaoe eee EE E EAE EEE EENES 94 Vivid SRGB inea e e ete al a a a e sett 95 A E E E E 95 Document preview IM
8. Fax and scan functionality are not included with this software Use the following instructions to install the printer driver only 1 Click Start and then do one of the following or For Windows Server 2003 and Windows XP Professional Select Settings and then click Printers and Faxes or For Windows XP Home Click Control Panel and then double click the Printers and Other Hardware icon or For Windows Vista Click Computer click Control Panel and then click Hardware and Sound 2 Click Add Printer and then click Next 3 When asked if the product is a local or network product select A network printer or a printer attached to another computer and then click Next E NOTE Use ofa local port is recommended if it is available If no local port is available create a new TCP IP port 58 Chapter 3 Install Windows printing system components ENWW 4 On the Install Printer Software screen click Have Disk The Install from Disk dialog box appears 5 Insert the printing system software CD into the CD ROM drive 6 Click Browse and then select the printer driver for the product To install the PCL 6 printer driver navigate to the root folder of the CD and select the hppdp608 inf file To install the HP postscript level 3 emulation printer driver navigate to the appropriate folder and select the appropriate file e For 32 bit Drivers win2k_xp_vista hppcps08 inf e For 64 bit Drivers winxp
9. Latvian Romanian Slovak Slovenian Serbian Thai Ukrainian Language list Arabic Bahasa Indonesian Bulgarian Catalan Croatian Czech Danish Dutch English Estonian Finnish French German Greek Hebrew Hungarian Italian Japanese Kazakh Korean Latvian Lithuanian Norwegian Polish Portuguese Romanian Russian Serbian Simplified Chinese Slovak Slovenian Spanish Swedish Thai Traditional Chinese Turkish Ukrainian Vietnamese Chapter 1 Document and product basics ENWW Documentation languages ENWW The product provides documentation in the following languages Table 1 5 Documentation languages Component HP LaserJet Pro CM1410 Color MFP Series User Guide PDF file HP LaserJet Pro CM1410 Color MFP Series User Guide CHM file HP LaserJet Pro CM1410 Color MFP Series Driver Preconfiguration User Guide Available in English only HP JetDirect Administrator s Guide PDF file with the following exceptions Catalan documentation in Spanish only No documentation in Arabic Bulgarian Czech Greek Hebrew Croatian Estonian Lithuanian Latvian Romanian Slovak Slovenian Serbian Turkish Ukrainian HP LaserJet Pro CM1410 Color MFP Series Install Notes HTML file Language list Arabic Bahasa Indonesian Bulgarian Catalan Croatian Czech Danish Dutch English Finnish French German Greek Hebrew Hungarian Italian Kazakh Korean
10. Special pages To specify special pages to be used click the Settings button under Special Pages 74 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW Covers To use specific cover settings click Covers in the Special Pages group box Use the Covers options to include a blank or preprinted cover on a document or to include a front back cover from a source tray that is different from the one used for the remainder of the document The following are the Covers options e Adda blank or preprinted cover Select which cover is customized Front Back or Both e Paper source The Paper source setting specifies the source tray to use for adding a front and or back cover to the document The list of source trays depends on the accessories that are installed Any optional trays that are installed through the Device Settings tab also appear here e Paper type The Paper type setting specifies the paper size to use for front and or back covers Changes made to the Paper type setting here override any previous Paper type settings using the same paper source r NOTE The same size of paper will be used for the entire print job When you change the type and source of the paper and covers the settings remain configured until you close the software program Print pages on different paper Use the Print pages on different paper options to select an alternative paper type or source for the first last or oth
11. e Color Options e Color Themes e Document preview image 92 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW Color Options Use the Color Options group box to adjust the independent color controls The settings affect the print job color rendering and print quality The Color Options group box contains the following controls Automatic Automatic option default Manual option Settings button Click this button to open the Color Settings dialog box Print in Grayscale check box Use the Automatic option for color settings that automatically fine tune the printed output The Automatic color settings provide high quality output while maintaining product performance for most color printing needs Manual To change the color settings select the Manual option and then click Settings The Color Settings dialog box appears To change the settings make your selections by using the drop down menus in the Color Settings dialog box and then click OK The following figure shows the Color Settings dialog box with Custom settings The Color Settings dialog box contains the following controls ENWW General o gt Edge Control Text gt Neutral Grays Graphics gt Neutral Grays Photographs e Neutral Grays Color tab features 93 Neutral Grays The Neutral Grays drop down menu controls the selection of a device dependent color table that is embedded in the p
12. From the Home screen touch the Setup amp button 2 Touch the Reports button 3 Touch the Configuration Report button 132 Chapter 6 Solve problems ENWW Print quality troubleshooting tools Calibrate the product to align the colors If the printed output has colored shadows blurry graphics or areas that have poor color you might need to calibrate the product to align the colors Print the Diagnostics Page from the Reports menu on the control panel to check the color alignment If the blocks of color on that page are not aligned with each other you need to calibrate the product 1 On the product control panel open the System Setup menu 2 Open the Print Quality menu and select the Color Calibration item 3 Select the Calibrate Now option Control panel menus Setup Menu ENWW To open this menu touch the Setup button The following sub menus are available e Reports e Quick Forms e Fax Setup e System Setup e Service e Network Setup Tools for troubleshooting 133 Reports menu Menu item Demo Page Description Prints a page that demonstrates print quality Menu Structure Prints a control panel menu layout map Configuration Report Prints a list of the product settings Supplies Status Prints the print cartridge status Includes the following information e Estimated percentage of cartridge life remaining e Approximate pages remaining e Part numbers for HP
13. NOTE If the PORT1 icon does not appear as a folder name you might have to enable folder viewing for FTP sites in your Web browser In Microsoft Internet Explorer use the following procedure to enable the folder view 1 2 3 Select Tools then select Internet Options and then select the Advanced tab Select the Enable folder view for FTP sites Click OK to save the setting 238 Chapter 7 Engineering Details ENWW Print ready file printing by using FTP on a direct network connection If the HP LaserJet Pro CM1410 Color MFP Series uses a direct network connection use file transfer protocol FTP to print a printready file Complete the following steps for the operating system Windows operating systems 1 Take note of the TCP IP address on the Embedded Jetdirect page The HP Embedded Jetdirect page is the second page of the configuration page printout 2 Open a command window on the computer 3 Type ftp lt TCP IP product ADDRESS gt For example if the TCP IP address is 192 168 0 90 type the following ftp 192 168 0 90 Press Enter on the keyboard When prompted for the user name press Enter When prompted for the password press Enter Type bin at the command prompt See ae oe Press Enter The message 200 Types set to I Using binary mode to transfer files appears in the command window 9 Type put lt FILENAME gt where lt FILENAME gt is the name of the printready file to be printed including the p
14. Seale to Fit is selected when Print Document On is selected If the setting is turned off then the document page images will not be scaled and are instead centered at full size on the target paper If the document size is larger than the target paper size then the document image is clipped If it is smaller then it is centered within the target paper When the size for which the document is formatted that is the logical size differs from the target size the preview image uses a dashed gray line to show the boundaries of the logical page in relation to the target paper size of Actual Size ENWW The of Actual Size option provides a slider bar and input box to use for scaling the percentage setting The default setting in the entry box is 100 of actual size Actual size is defined as the paper size that is selected within the driver or what the driver receives from the software program if the software program does not negotiate the paper size with the driver The driver scales the page by the appropriate factor and sends it to the product Effects tab features 79 The limits of the range are from 25 to 400 and any values outside the range are adjusted to those limits as soon as the focus is removed from the control that is when the Tab key is pressed or another control is selected Any change to the scale also changes the page preview which increases or decreases from the upper left corner of the preview The slider bar
15. Selecting this will run a configuration dialog after clicking the Create Package Install Type Silently preload the driver is the option to select for users that will be using a direct connection like a USB cable A future Plug and Play event will be necessary to install the print driver but all the files will be installed in the Windows driver store by this package for future use By default the executable file runs silently If you would like to prompt the end user to connect the product at the end of the install select the Show a prompt to connect the printer checkbox For products using a network connection select the Silently create the network port and install driver option The Network Settings button will become enabled and you should click on it to enter the required network settings E NOTE If you do not select the print driver first an error dialog box appears You must select the print driver first so that the product name can be derived from the printer driver name Figure 2 7 Network Settings Network Settings Required Settings Identify the network printer by one or more of the following IP Address Hardware Address Hostname Additional Settings Port Name HPPrintPort Printer Name HP Universal Printing PCL 6 Set this printer as default printer No Share this Printer No Share Name You must identify the network product by one of
16. Windows 239 e mail unable to send 220 local port Windows 240 Windows programs V 34 setting 220 LPR 241 supported 32 fax menu 146 networks Windows 241 e mail alerts setting up 125 fax reports printing 146 UNIX 241 Enterprise AutoConfiguration Fax tab HP ToolboxFX 126 disabling about 20 fax troubleshooting driver features 25 Novell NetWare operating checklist 204 disk space requirements systems supported 22 file formats supported 29 Macintosh 112 Windows operating systems fonts document feeder supported 2 install remove external fonts jams 173 documentation administrator 5 availability by operating system 3 file formats 3 HP driver configuration 6 HP Jetdirect 6 HP Jetdirect Guide 6 install notes 5 languages 13 error messages 99 control panel 151 Send True Type as Bitmap print eventlog 168 drivers 68 error messages fax 220 227 supported by Windows 38 error report fax True Type print drivers 67 printing 219 Windows 40 error correction setting fax 219 FTP escape sequences media source 243 mediatype 244 G event log 125 glass cleaning 190 direct printing Windows 239 user guide 4 exporting driver parameters 25 graph paper printing 135 viewing 3 guides See documentation dpi dots per inch F faxing 137 factory defaults restoring H drivers NVRAM initialization 204 help print drivers 64 Windows 17 Help tab HP ToolboxFX 128 HP Driver Configuration 23 accessory configuration 20 factory set defau
17. Windows XP Windows Server 2003 or Windows Server 2008 1 2 3 4 5 Click Start select Settings select Control Panel and then select Printers Select the printer that you just installed On the toolbar click File Click Properties Click the Port tab to change the port information Windows Vista and Windows 7 1 2 3 4 Click Start click Control Panel and then in the category for Hardware and Sound click Printers or Devices and Printers Right click the printer that you just installed Click Printer Properties Click the Port tab to change the port information Printer driver only Add Printer Windows XP Windows Server 2003 and Windows Server 2008 N Close all programs Click Start click Settings click Control Panel and then click Printers Click Add a printer Answer the questions in the Add Printer Wizard until you reach the screen that shows the printer manufacturer list Click Have Disk 248 Chapter7 Engineering Details ENWW 6 Browse to the printer driver location using one of the following options e CD ROM Browse to the DRIVERS OS PDL directory for your operating system on the software CD e Internet download Browse to the folder where the Web files were downloaded and decompressed 7 Select the appropriate INF file 8 Click Open and then click OK 9 Select the appropriate printer 10 Follow the remaining onscreen instructions to complete the printer
18. and the At Very Low menu item in the System Setup menu is set to Continue Recommended action To ensure optimal print quality HP recommends replacing the print cartridge at this point You can continue printing until you notice a decrease in print quality Actual cartridge life may vary Once an HP supply has reached very low HP s premium Protection Warranty on that supply has ended All print defects or cartridge failures incurred when an HP supply is used in continue at very low mode will not be considered to be defects in materials or workmanship in the supply under the HP Print Cartridge Warranty Statement ENWW Tools for troubleshooting 167 Event log messages 168 The following product events do not produce a message that appears on the control panel Instead they are recorded in the event log To print the event log open the secondary service menu select Service Reports and then select Error Report Table 6 1 Event log messages Event code Description 13 0000 Paper jam 20 0000 Memory out 21 0000 Page misfeed or mispick 41 2000 Beam detect malfunction 41 3000 Unexpected size 50 1000 Low fuser temperature error 50 2000 Slow fuser error 50 3000 High fuser temperature error 50 4000 Fuser drive circuit error 50 7000 Fuser open error 50 8000 Low subthermistor fuser error 50 9000 High subthermistor fuser error 51 2000 Black scanner laser err
19. contact HP See www hp com support CM141 Oseries or the support flyer that came in the product box The Communication error message appears e Ask the sender to send the fax again or send at a later time when line conditions have improved e Unplug the product telephone cord from the wall plug in a telephone and try making a call Plug the product phone cord into a jack for another phone line e Try a different phone cord e Set the Fax Speed option to the Slow V 29 or Medium V 17 setting or disable the Fast V 34 setting a From the Home screen touch the Setup N button Open the Fax Setup menu c Open the Advanced Setup menu d Open the Fax Speed menu e Select the correct setting e Turn off the Error Correction feature to prevent automatic error correction E NOTE Turning off the Error Correction feature can reduce image quality From the Home screen touch the Setup button Open the Service menu c Open the Fax Service menu d Open the Error Correction menu e Select the Off setting e Print the Fax Activity Log report from the control panel to determine if the error occurs with a specific fax number a Touch the Fax button and then touch the Fax Menu button b Open the Fax Reports menu 230 Chapter 6 Solve problems ENWW c Open the Fax Activity Log menu d Select the Print Log Now option e Ifthe error persists contact HP See www hp com support CM 141 Oseries or the support flyer t
20. e Printing system software on the Web e In box printing system software CD 114 Chapter 5 Macintosh software and utilities ENWW Printing system software on the Web All software that is contained on the installation CDs is also available on the Web Web deployment is the preferred method for obtaining the latest software The HP Web site offers an option for automatic e mail notification about new software releases NOTE This STR describes drivers that are shipped on the printing system software CD that comes with the product This STR does not describe drivers that will become available on the Web The printing system software is available for download at the following Web site www hp com support CM 14 1 Oseries In box printing system software CD One CD is included in box with the product The printing system software CD contains the following components e Software installer e Links to the HP Universal Print Drivers on the Web e User guides e Support information The CD is divided into two partitions one for each of the following operating systems e Windows e Macintosh The files in each partition of the printing system software CD include documentation files and files that are required to install and uninstall the printing system software components Use the printing system software CD to install the printing system software e Macintosh disk Macintosh disk The HP Macintosh printing system softw
21. or damaged If necessary use paper from a different package Make sure the tray is not overfilled If it is remove the entire stack of paper from the tray straighten the stack and then return some of the paper to the tray Make sure the paper guides in the tray are adjusted correctly for the size of paper Adjust the guides so they are touching the paper stack without bending it Prevent paper jams ENWW To reduce the number of paper jams try these solutions 1 2 Use only paper that meets HP specifications for this product Use paper that is not wrinkled folded or damaged If necessary use paper from a different package Use paper that has not previously been printed or copied on Make sure the tray is not overfilled If it is remove the entire stack of paper from the tray straighten the stack and then return some of the paper to the tray Paper feeds incorrectly or becomes jammed 171 5 Make sure the paper guides in the tray are adjusted correctly for the size of paper Adjust the guides so they are touching the paper stack without bending it 6 Make sure that the tray is fully inserted in the product Clear jams Jam locations Jams can occur in these locations 1 Document feeder 2 Output bin 3 Tray 1 4 Rear door Loose toner might remain in the product after a jam This problem typically resolves itself after a few sheets have been printed 172 Chapter 6 Solve problems ENWW Cl
22. port Check the phone line by using the Run Fax Test option from the Service menu on the control panel a From the Home screen touch the Setup N button b Open the Service menu c Open the Fax Service menu d Select the Run Fax Test item If the error persists contact HP See www hp com support CM 141 Oseries or the support flyer that came in the product box Document feeder paper jam Verify that the paper meets product size requirements The product does not support pages longer than 381 mm 15 in for faxing Copy or print the original to letter A4 or legal size paper and then resend the fax 222 Chapter 6 Solve problems ENWW The Fax storage is full message appears e Turn the product off then on e Print stored faxes that have not been printed a Touch the Fax button and then touch the Fax Menu button Open the Receive Options menu c Select the Print Private Faxes item d Provide the password when the product prompts you e Delete stored faxes from memory a From the Home screen touch the Setup amp button Open the Service menu c Open the Fax Service menu d Select the Clear Saved Faxes item Divide the large fax job into smaller sections and then fax them individually Scanner error e Verify that the paper meets product size requirements The product does not support pages longer than 381 mm 15 in for faxing e Copy or print the original onto letter A4 or legal size paper and
23. print optimization features such as substituting device fonts for TrueType fonts and scanning for horizontal and vertical rules are turned off Printer Features The Printer Features setting contains the following controls e Print All Text as Black The feature is Disabled by default When Enabled is selected the driver prints all text as black regardless of the original document text color Color text is printed as black except for white text which remains white White text is a reliable method of printing reverse typeface against a dark background This setting does not affect graphic images on the page nor does it affect any text that is part of a graphic e Send True Type as Bitmap Send True Type as Bitmap provides an alternative for software programs that have trouble using TrueType fonts for special graphic aspects such as shading rotation or slanting The setting is Disabled off by default The TrueType fonts are converted to bitmap soft fonts before downloading The Enabled setting causes the driver to send TrueType fonts to the product as outlines which retains the standard format outline of the fonts 68 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW e Raster Compression Use the Raster Compression feature to select the graphics compression method gt Automatic The software determines the best compression method to use gt Best Quality This option forces the software to use a
24. start Readiris and scan directly into the program Readiris v12 0 automatically starts a wizard to help guide this process When Readiris is installed on the computer it appears as an option in the destination drop down box in the HP Scan software If you select Readiris as the destination the image is scanned into TIFF format and Readiris automatically starts the textrecognition process The Readiris software uses a separate installer that comes on a separate CD The initial release of the product includes Readiris Professional software Online Help Provides help for using the product software The user documentation for this product is included on the installation CD as both CHM online help files and Adobe Acrobat PDF files A Web browser must be installed on the computer to view the contents from any CHM file Adobe Acrobat Reader must be installed on the computer to view the contents from any PDF file ENWW Windows printing system software 17 HP Color LaserJet print drivers HP LaserJet Pro CM1410 Color MFP Series print drivers provide the printing features and communication between the computer and the product The software CD includes software for end users and network administrators who are working in the following operating environments e Windows XP 32 bit and 64 bit Windows Server 2003 32 bit and 64 bit Windows Server 2008 32 bit and 64 bit and Windows Vista 32 bit and 64 bit and Windows 7 32 bit and
25. type a name in the Group name window and then click OK To edit an existing individual speed dial entry click anywhere on the row containing the contact name to select it and then click Update Type changes in the appropriate windows and then click OK To edit an existing group speed dial entry click anywhere on the row containing the group name to select it and then click Update Group Make any required changes and then click OK To delete an entry from the speed dial list select the item and then click Delete To move speed dial entries select the entry and then click Move or select Move and then specify the entry in the dialog box Either select Next empty row or specify the number of the row where you want to move the entry NOTE If you specify a row that is occupied the new entry will overwrite the existing entry 126 Chapter 6 Solve problems ENWW NOTE You must click Apply before the changes take effect ENWW To import contacts from a phone book that exists in Lotus Notes Outlook or Outlook Express click Import Export Phone Book Select the Import option and then click Next Select the appropriate software program navigate to the appropriate file and then click Finish To export contacts from a phone book click Import Export Phone Book Select the Export option and then click Next Enter the file name or browse to the file to which you want to export contacts and then click Finish You can als
26. 1 Reattempt the fax transmission at a different time when telephone line conditions have e The sending product has failed to respond to improved a fax command from the receiving product due to the connection being interrupted 2 If the error persists disable ECM e The sender has touched the Cancel X button while the reception was in progress 384 The receiving product has attempted a black JPEG Reattempt the fax transmission using a different transmission fo a product that does not support this mode mode Solve fax problems 213 214 Table 6 5 Fax send error codes continued Error code Description Solution 386 The receiving product has failed to complete the third phase of the initial V 34 handshake after originating a fax session This is usually due to poor line conditions although it may be a compatibility issue with certain products and or line conditions 387 The receiving product has failed to successfully negotiate the initial V 8 handshake with the sending product after originating a fax session Typically this will occur when the sending product is not fax capable or has disabled reception It may also be a compatibility issue with certain products and or line conditions 388 The receiving product has originated a fax session and detected a sending fax product but has been unable fo detect any T30 frames If the product is in V 17 mode it is likely that the connection has been interrupted
27. 2 Update the firmware 50 x Fuser Error Description ENWW Tools for troubleshooting 15 152 The product has experienced an internal hardware error 50 1 Low fuser temperature error 50 2 Slow fuser error 50 3 High fuser temperature error 50 4 Fuser drive circuit error 50 7 Fuser open error 50 8 Low subthermistor fuser error 50 9 High subthermistor fuser error Recommended action 1 2 3 Turn off the power by using the power switch and then wait at least 30 seconds If a surge protector is being used remove it Plug the product directly into the wall socket Turn on the power and wait for the product to initialize Chapter 6 Solve problems ENWW 79 Error Turn off then on Description The product has experienced an internal firmware error Under most conditions the product automatically restarts Recommended action Turn off the power by using the power switch wait at least 30 seconds and then turn on the power and wait for the product to initialize If a surge protector is being used remove it Plug the product directly into the wall socket Use the power switch to turn the product on If the error persists try the following solutions 1 Perform an NVRAM initialization 2 Update the firmware Black Cartridge Low Description The print cartridge is nearing the end of its useful life Recommended action Printing can continue but consider having a replacement supply on hand
28. 64 bit e Apple Mac OS X v10 5 and later In Windows operating systems automatic configuration driver updates after a new product configuration and preconfiguration features are available with the HP LaserJet Pro CM1410 Color MFP Series product NOTE For additional information about installing the printing system software see the HP LaserJet Pro CM1410 Color MFP Series Install Notes on the printing system software CD All of the drivers provide access to the paper handling and print quality features HP PCL 6 Print Driver PCL 5 Universal Print Driver and PS Universal Print Driver All of the Windows drivers are supported by Microsoft 32 bit and 64 bit operating systems The HP PCL 6 driver is included on the HP LaserJet Pro CM1410 Color MFP Series printing system software CD The PCL 5 Universal Print Driver and the PS Universal Print Driver are available for download at the following Web site www hp com support CM14 1 Oseries NOTE Ifyou select the recommended installation by clicking Install Now on the main screen of the Installer the HP PCL 6 Print Driver is installed by default Print driver version numbers for Windows operating systems Access to print driver version numbers varies depending on the operating system in which the HP LaserJet Pro CM1410 Color MFP Series product is installed NOTE Fora list of HP LaserJet Pro CM1410 Color MFP Series print drivers updated HP printing system softwar
29. A A AT ERER 126 Fa Receive niens aens EESE EE EEE EER RE ESS 126 Fax phone b ok srn ernieren A 126 Fax send log oee Ee EE E E E E AT E a 128 Fax receive logiaren e ae a R 128 BIGEK FAXES morae a a a eA a 128 Help iui i e e E cna ie wena E a EE 128 System SehingS sie e cadres e e e E E suas E EE E EEEO 129 Device Information 2 at rd ety tortie nei iaanink edly Col ANS 129 Paper Setlp s icdihindivsraesdosatsvavrdganvdgerebasanladcoees r s a aiaa 130 BANKENE E RA A A A A ties 130 Print Density onon e a R ate eet E ia 130 Paper Types osea a e A E EE E e i 130 System SEU p ien n a EO E R E EA 131 Device polling ciskindcsnetonwbiere dives ors taint aguateetaiteonsebeernaes shougndeaeles 131 Print Settings cesor sees cot dde doen e e onenteceat aie dee dndveneass sea a aE 131 PRINTING eean o E a aia vee reas 13 PELS setae aces Bee cit rg a de Ale eae Nace clita ete ata 131 POSESGHIDL ai ocassatetaaetcndetccdacs E aeemietes leteeataden teense dae 131 Nefwork Selings ennir a a a a ute S 131 Internal print quality test pages 524 says Gaqsartyracadeedbanceceducade esvsedasmnnasece etna sundesoandens 132 Configuration Pagers Ai sicsddsletauestauce cd Aiaed Madetengan coaceclnnstidiucee tans teeedees 132 Print quality troubleshooting 100ls s accustandveGmeinn catiun awn cate onctoeweanmnncenns 133 Calibrate the product to align the colors i 3sc0 cscasessnessedansdaaxeevnasaaawnedan santas 133 Gonirol panel Tae US cosas od pap A T A
30. Any entry that is greater than the maximum limits of the width and height control is rounded down to the maximum valid entry while any entry that is smaller than the minimum limits of the width and height control is rounded up to the minimum valid entry If units are in millimeters the custom paper size range minimum is the limit rounded up to the nearest whole millimeter The custom paper size range maximum is the limit rounded down to the nearest whole millimeter Any non numerical entry reverts to the minimum value Width and height entries are validated when the focus has changed The resolution of each control is 1 millimeter or 1 10 of an inch depending on the current measurement units Units To change measurement units click one of the options in the Units group box either Inches or Millimeters Custom width and height control limits The minimum paper size for the HP LaserJet Pro CM1410 Color MFP Series product is 76 x 127 mm 3 x 5 in and the maximum is 215 90 x 355 60 mm 8 50 x 14 00 in Paper source The Paper source setting specifies the source tray to use for printing a document The list of source trays depends on the product accessories that are installed Any optional source trays that are installed through the Device Settings tab also appear here The Paper source drop down menu can contain the following options depending on what has been installed on the product e Automatically select e Printer Auto Selec
31. Auto Configured 06 21 42010 Administrator Preferences Not Applied Last configured 06 21 42010 Auto Configured LA invent The About tab lists driver installation file names and their version numbers The About tab also indicates whether the driver was autoconfigured whether administrator preferences were set the date the driver was last configured and whether the configuration is autoconfigured or user configured The About button is also available on most driver screens The About button provides a driver version number and creation date ENWW About tab features 109 110 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW 5 Macintosh software and utilities ENWW Supported operating systems for Macintosh Macintosh system requirements Macintosh printing system software Macintosh install and uninstall instructions 111 Supported operating systems for Macintosh The product supports the following Macintosh operating systems e MacOS X v10 5 and v10 6 E NOTE PPC and Intel Core Processor Macs are supported Macintosh system requirements Hardware requirements e 256 MB RAM e 150 MB HD free space e CD ROM e Hi Speed USB 2 0 Macintosh printing system software The printing system software for Macintosh is composed of an HP created postscript PS printer definition file PPD and a Printer Dialog Extension PDE file that work together with the Macintosh
32. Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW e Use defined printing shortcuts e Snapshot Photos e Labels e Labels Create a custom printing shortcut Use defined printing shortcuts The Printing Shortcuts tab contains the following pre defined shortcuts e General Everyday Printing e Eco print Two sided Printing e Factory Defaults e Envelopes e Cardstock Heavy e Glossy Presentation General Everyday Printing When General Everyday Printing is selected the following controls are available e Paper source e Paper sizes e Paper type e Print on both sides When options other than the defaults are selected the Save as and Reset buttons become active Click Save as to create a custom printing shortcut Click Reset to change customized settings back to the default settings Paper source The following options are available e Automatically Select default e Printer auto select e Manual Feed in Tray 1 e Tray 1 ENWW Printing Shortcuts tab features 103 Paper sizes The following options are available Paper type The following options are available 104 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows A4 Letter default Legal Executive 8 5x13 4x6 5x8 A4 A5 A6 RA4 SRA4 B5 JIS 10x15cm 16k 195x270mm 16k 184x260mm 16k 197x273mm Japanese Postcard Double Japan Postcard Rotated Envelope 10 E
33. E a 133 Setup Meninis uraii iaoee a a aa TO EE E A T a 133 viii BINAAN ENWW Reports M nu sra reae a ia ava ater eee 134 Quick Forms MeRU omesse darinenn eee e a 135 Fax Setup men seie e ee E heen EEE lee 136 System SetUp MENU sooren sin i n a a eee a a i 139 Senice meni eesi a E 142 Network Setup Menu ncwn acetn Runn eee A 144 Function specific menus a coven asceranedsdceteseed storey le touadu ater tl eiedvundetmurrdsctas 145 Copy Menu iss searasadiass os setinna tiv aseddsteasecd ova sacvosantveierasteroua cma 145 Fax MERU stan eiwnarmtecn e S E a E ER endl EE E ans 146 Scan Menus p ee eaae Ee Eae Eae E AEO E S EAA 149 USB Flash Driveri re E E EEE ETE R E EA 150 Interpret control panel messages ccsseeesceeceeeeeeeeeeeenneeeeeeeeeeeeeeenaeeeeeeeeeentaaeeeeeees 151 Control panel message types secceceeseeeesceeeeeeeeeeenceeeeeeseseneeeeeeeeeeeeaes 151 Control panel messages 245 aoivn osha erent renee 151 10 100X Supply Memory Error anixcniwetsmancniamiautreiinedechancwenacane 151 49 Error Turn off then On ccecccccsseseccceeseccsesecceauesceseunessens 151 SOS Fuser Error sher sane a n E AE dene SEEE EEE 151 79 Error Turn off then sOMiros t wr ccoavon couse on ewerioseatancandseseundvatnath aan 153 Black Cartridge Low vcuet rater ee awed ees 153 Black in wrong position is is raga ccm ous athe comedian etues Caine cee NNe ite 153 Black Very LOW rinri nauk hedon aaah a 153 Canceled scan Clear document
34. Fax dialog box to see the new entries in the Phone Book field Create a cover page If you want a cover page for the fax select Cover Page in the Include With Fax options Your name company name phone number and fax number are entered automatically into the cover page template Edit the data for the cover page template by using one of the following methods e Enter the data for the cover page in the HP LaserJet Fax Setup Utility e Enter the data for the cover page on the product control panel e Enter the data for the cover page by clicking Defaults and then clicking Edit When you select Cover Page the Notes section appears To view a completed cover page template select one from the drop down menu and then click Preview NOTE Cover page templates are not editable Fax pages scanned from the product document feeder If you want to include fax pages scanned from the product document feeder place the pages to be scanned in the product document feeder and select Pages in Document Tray in the Include With Fax options Fax without first printing and scanning the document One of the most useful features of the HP LaserJet Send Fax software is the ability to fax documents without first printing and scanning them For example if you want to send a Microsoft Word document open the document click File click Print and then select HP LaserJet CM1410 MFP Fax from the drop down menu The HP LaserJet Send Fax sof
35. HP s premium Protection Warranty on that supply has ended All print defects or cartridge failures incurred when an HP supply is used in continue at very low mode will not be considered to be defects in materials or workmanship in the supply under the HP Print Cartridge Warranty Statement Manual Duplex Load Tray 1 Press OK Description Manual duplex mode Recommended action Load paper in the correct orientation Manual feed lt SIZE gt lt TYPE gt Press OK to use available media Description Print Manual Feed mode Recommended action Load paper into Tray 1 Memory is low Try again later Description The product does not have enough memory to start a new job Recommended action Wait until the current job is finished before starting a new job Turn the product off and then on to clear the memory If the error persists try the following solutions 1 Perform an NVRAM initialization 2 Update the firmware Memory is low Press OK Description The product memory has been almost completely filled 162 Chapter 6 Solve problems ENWW Recommended action Touch the OK button to cancel the job Break the job into smaller jobs that contain fewer pages Turn the product off and then on to clear the memory Memory low Only 1 copy made Press OK to continue Description The product does not have enough memory to complete the collated copy job Recommended action Break the job into smaller jobs that contain fewer pages Turn t
36. In V 34 mode is also possible for this error to occur due to compatibility problems with certain products and or line conditions 389 The receiving product has originated a fax session and has reattempted V 8 negotiations multiple times without success 1 Reattempt the fax transmission at a different time when telephone line conditions have improved 2 Disable V 34 on the receiving product and attempt the transmission using the V 17 mode 390 The receiving product has originated a fax session using error correction either V 34 or V 17 Transmission of an image has been abandoned after a timeout when no data has become ready for transmission This is most likely due to a low memory condition although it could be due to other internal problems that cause generation of data for transmission fo stall 391 The receiving product has originated a fax session without error correction not V 34 Transmission of an image has been abandoned after a timeout when no data has become ready for transmission This is most likely due to a low memory condition although it could be due to other internal problems that cause generation of data for transmission to stall Chapter 6 Solve problems Reattempt the transmission after making sure documents stored in memory are printed and the product has paper ready for printing If the problem persists reinitialize permanent storage ENWW ENWW Table 6 5 Fax send error codes c
37. Macintosh printing system software cccccceeeeeeeeeeeeeeeeeeeeteeeeeeneaeeeeeeesaes 116 General installation for Macintosh operating systems ccccssceeeeeeeeeeeees 116 Setup INSHPUCTIONS c0 ssesecnsanenstnaneneaaventecsstecs oans n E e nena i Ena 116 Setting up a printer with Mac OS X v10 5 and v10 6 eee 117 Troubleshooting the product setup cccceceeeeeeeeeetttettteeeeeeees 117 Remove the printing system software from Macintosh operating systems eeeseeee 118 6 S lve problems scsscsscevesessicsass ivedecwisasdianstacavades vicnadtenuaed seceadicnsbsenunaes undacdadennsavaaeedionaavens 119 Problem solving checklist iciragcsvirnsacintnerbesveannasewan tase daepee unialedvan asiranguie uhcaabeiwlas oveipsn lcd paielburalebonclabedpabebintaaiores 120 Step 1 Check that the product power is OM c ccccsesseceseeseeeeeeeeeeeeeeeeeeseeeeeeeeeeeees 120 Step 2 Check the environment where the product is installed ceseseeceeteeeeeneeeeens 120 Step 3 Check the control panel for error MESSAGES ceeecceeeesseeeeetceeeeesseeeeeteaeeeees 120 Step 4 Test print functionality sess ssi kstievatsecnedesicainn etl Ookuslel nti bd elibaivnsabnslnelisnidoiheiididetalpte isis 121 Step 5 Test copy functionality s4 cai cu cianwnsieavaxatedahvntatnaginccnenulesdetesiennaradleseuanabindeeinlavpaniines 121 ENWW vii Step 6 Test the fax sending functionality ccccccceessecceeteeee
38. Mbps half duplex operation 10T Full 10 Mbps full duplex operation 100TX Half 100 Mbps half duplex operation 100TX Full 100 Mbps full duplex operation 5 Touch the OK button The product turns off and then on Control panel LEDs The state of the Ready light and Attention light on the product signal the product status The following table outlines the possible control panel light states amp NOTE Wireless models have a blue LED that illuminates when the product wireless function is enabled and available Product state Ready light state Attention light state Initializing Blinking Blinking Ready On Off Receiving data processing job or Blinking Off cancelling job ENWW Tools for troubleshooting 123 Product state Ready light state Attention light state Error message Off Blinking Fatal error 49 or 79 error On On The product restarts after one of these errors Occurs Control panel diagnostics The product includes diagnostic tests for the control panel Test the control panel display 1 Touch the Setup amp button Touch the left arrow button and then quickly touch the Cancel X button 2 3 Touch the Setup amp button to return to the main menus 4 Open the 2ndary Service menu 5 Open the Display test menu Test the control panel buttons 1 Touch the Setup amp button Touch the left arrow button a and then quickly touch the Cancel X button 2 3 Touch the Setup 4
39. NCSR75W TTF New Century Schoolbook Bold Italic NCSR76W TIF New Century Schoolbook Italic NCSR56W TTF New Century Schoolbook Roman NCSR55W TTF Palatino Bold PALR6SW TTF Palatino Bold Italic PALR66W TTF Palatino Italic PALR46W TTF Palatino Roman PALR45W TTF SymbolPS Regular SYMPS__ TTF Times Bold TIMR65W TTF Times Bold Italic TIMR66W TTF Times Italic TIMR46W TTF Times Roman TIMR45W TTF Univers Bold UNVR65W TTF Univers Bold Italic UNVR66W TTF Univers Condensed Bold UNVR67W TTF Univers Condensed Bold Italic UNVR68W TTF Univers Condensed Medium UNVR57W TTF Univers Condensed Medium Italic UNVR58W TTF Univers Medium UNVR55W TTF Univers Medium Italic UNVR56W TTF Ninety two additional PS emulation fonts are also available on the CD Chapter 2 Windows software description ENWW ENWW Table 2 9 Additional PS emulation fonts Font name Font style File name Albertus MT Regular PS_12639 1TF Albertus MT Italic PS_12640 TTF Albertus MT Lt Regular PS_14530 TTF Antique Olive CompactPS Regular PS_11120 TTF Antique Olive Roman Regular PS_11119 TTF Antique Olive Roman Bold PS_11118 1TF Antique Olive Roman Italic PS_11846 TTF Apple Chancery Italic PS_24516 TTF Bodoni Poster Regular PS_12704 TTF Bodoni PosterCompressed Regular PS_14508 TTF BodoniPS Regular PS_12581 TTF BodoniPS Bold PS_12585 TTF BodoniPS Bold Italic PS_12586 TTF BodoniPS Italic PS_12582 1TF Cand
40. Paper Output setting contains the Copy Count setting 66 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW Copy Count Copy Count specifies the number of copies to print This driver setting is useful for software programs that do not provide a copy count If a copy count is available in the software program set the copy count in the software program The number of copies that you request appears in the Copy Count option You can select the number by typing in the text box or by using the up and down arrows to the right of the text box Valid entries are numbers from 1 to 9999 The copies value will not advance from the maximum number 9999 to 1 when the up arrow is used or change from 1 to the maximum number 9999 when the down arrow is used When you click another group box or leave the Advanced tab invalid entries into the text box such as non numerical input numbers less than 1 or numbers greater than the maximum allowed are changed to the last valid value that appeared in the text box The default number of copies is 1 Because you can set the number of copies that you want from some software programs conflicts between the software program you are using and the driver can arise In most cases the software program and the driver communicate so that the number of copies set in one location such as the program will appear in the other such as the driver For some programs this communication does not
41. SKWW Slovenian SL Slovenian SLWW Spanish ES Espanol ESWW Swedish SV Svenska SVWW Thai TH Thai THWW Traditional Chinese ZHTW Traditional Chinese ZHTW Turkish TR Turkce TUWW Ukrainian UK Ukrainian UKWW Vietnamese VI Vietnamese VIWW 10 Chapter 1 Document and product basics ENWW Driver languages ENWW The product provides driver support in the following languages Table 1 3 Supported printer driver languages Component HP PCL 6 Print Driver HP PCL 5 Universal Print Driver HP PS Universal Print Driver Language list Arabic Bahasa Indonesian Bulgarian Catalan Croatian Czech Danish Dutch English Estonian Finnish French German Greek Hebrew Hungarian Italian Japanese Kazakh Korean e Latvian e Lithuanian e Norwegian e Polish e Portuguese e Romanian e Russian e Serbian e Simplified Chinese e Slovak e Slovenian e Spanish e Swedish e Thai e Traditional Chinese e Turkish e Ukrainian e Vietnamese Software availability and localization 1 Installer languages 12 The product provides installer component support in the following languages Table 1 4 Installer component languages Component Administrator install Installer Common Windows installer Web registration with the following exceptions e Arabic and Hebrew support in English only e Catalan support in Spanish only e No support for Bulgarian Estonian Croatian Lithuanian
42. Service menu d Open the Error Correction menu e Select the Off setting NOTE This can reduce image quality e Use white paper for the original Do not use colors such as gray yellow or pink e Increase the Fax Speed setting Open the Setup menu b Open the Fax Setup menu c Open the Advanced Setup menu d Open the Fax Speed menu e Select the correct setting Divide large fax jobs into smaller sections and then fax them individually e Change the fax settings on the control panel to a lower resolution a Open the Setup N menu Open the Fax Setup menu c Open the Advanced Setup menu d Open the Fax Resolution menu e Select the correct setting ENWW Solve fax problems 233 Fax quality is poor Fax is blurry or light e Increase fax resolution when sending faxes Resolution does not affect received faxes Open the Setup N menu Open the Fax Setup menu c Open the Advanced Setup menu d Open the Fax Resolution menu e Select the correct setting amp NOTE Increasing resolution slows transmission speed e Turn on the Error Correction setting from the control panel Open the Setup N menu b Open the Service menu c Open the Fax Service menu d Open the Error Correction menu e Select the On setting e Check the print cartridges and replace if necessary e Ask the sender to darken the contrast setting on the sending fax machine and then resend the fax Fax cuts off or prints on two pa
43. Settings tab features NOTE The Device Settings tab is located on the Properties tab set For information about how to access these tabs see Properties driver tabs on page 63 Available options depend on the feature The following figure shows the Device Settings tab Figure 4 9 Device Settings tab amp HP LaserJet CM1410 Series PCL 6 Copy 1 Properties dg General Sharing Ports Advanced Color Management Security Device Settings About SS HP LaserJet CM1410 Series PCL 6 Device Settings 3 Form To Tray Assignment Printer auto select JEET Manual Feed in Tray 1 Letter Tray 1 Letter E B Font Substitution Table External Fonts EA Installable Options Automatic Configuration OFF 4llow Manual Duplexing Enabled Job Separator Disabled Printer Status Notification Enabled The Device Settings tab contains controls for paper handling devices and controls for managing the HP LaserJet Pro CM1410 Color MFP Series product The Device Settings tab contains the following controls e Form to Tray Assignment e Font Substitution Table e Installable Options Form to Tray Assignment A network administrator can use Form to Tray Assignment to specify the paper size in each input tray 98 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW The HP LaserJet Pro CM1410 Color MFP Series product supports more than one source of pape
44. Setup menu is set to Stop Recommended action To ensure optimal print quality HP recommends replacing the print cartridge at this point You can continue printing until you notice a decrease in print quality Actual cartridge life may vary Once an HP supply has reached very low HP s premium Protection Warranty on that supply has ended All print defects or cartridge failures incurred when an HP supply is used in continue at very low mode will not be considered to be defects in materials or workmanship in the supply under the HP Print Cartridge Warranty Statement Scanner error Turn off then on ENWW Description The product has experienced an error in the scanner sub assembly area Recommended action Scanner error 12 Turn off then on Motor test failure This error will only appear on the Error report The documentfeeder motor is not blocked from turning 1 Clear any jammed paper from the document feeder 2 Turn the product off and then on Scanner error 13 Turn off then on RAM Wall failure This error appears on the control panel The scanner motor or scanner module is obstructed A Turn the product off and then on Scanner error 14 Turn off then on Tools for troubleshooting 165 LED test failure This error will only appear on the Error report The LED did not illuminate during initialization o Replace the documentfeeder scanner assembly e Scanner error 17 Turn off then on Scanner error Thi
45. Size Letter Media Type Unspecified ape yee Printer Auto Select Description HP DDU Frequently Asked Questions How do I use the HP DDU to deploy a direct connect driver with preconfiguration If you load multiple PDLs for one product the operating system will determine which one satisfies the Plug and Play event The operating system will create one printer object for that PDL 1 Run HPDDU EXE to start the package creation 2 From Package Source section Select the print driver to package by browsing to the INF file in the directory b Select the Pre configuration checkbox This checkbox is enabled only for print drivers that support preconfiguration c Select the Silently preload the driver install type d Select the Show a prompt to connect the printer checkbox if you want to prompt the user after the files are copied 3 From Package Target section Select the output name and location Three files will be written here an EXE file a CAB file and an XML file with information about the package ENWW HP Driver Deployment Utility 49 50 From Create Package section a If you want to suppress any error messages select the Suppress all end user error messages checkbox b Click the Create Package button Run the new EXE file from the client computer You must have administrator rights to run the EXE file because it will be copying files into the Windows driver store Now the printer driver fi
46. Specks of toner are on the printed pages e Toner is smearing on the printed pages e Printed characters seem misformed e Printed pages are curled Always use a paper type and weight that this product supports In addition follow these guidelines when selecting paper e Use paper that is of good quality and free of cuts nicks tears spots loose particles dust wrinkles voids staples and curled or bent edges e Use paper that has not been previously printed on e Use paper that is designed for use in laser printers Do not use paper that is designed only for use in Inkjet printers e Use paper that is not too rough Using smoother paper generally results in better print quality Print a cleaning page Print a cleaning page to remove dust and excess toner from the paper path if you are having any of the following problems e Specks of toner are on the printed pages e Toner is smearing on the printed pages e Repeated marks occur on the printed pages Use the following procedure to print a cleaning page 1 From the Home screen touch the Setup button 2 Touch the Service menu 3 Touch the Cleaning Page button 4 Load plain letter or A4 paper when you are prompted 5 Touch the OK button to begin the cleaning process A page feeds through the product slowly Discard the page when the process is completed 182 Chapter 6 Solve problems ENWW Calibrate the product to align the colors If the printed output has c
47. The HP Web Jetadmin provides a queue creation program that can be used to create printer queues on Windows 2000 Windows XP Windows Server 2003 or Windows Server 2008 The HP Web Jetadmin Driver Configuration Plugin adds a number of screens to the existing queue creation workflow from which the drivers that are being installed for the queues can be customized as part of the process The plug in is limited to Internet Explorer browsers Netscape Navigator is not supported HP Web Jetadmin v10 0 is supported by the following o Windows XP Professional only o Windows Server 2003 R2 only e Windows Server 2008 o Windows Vista Business and Enterprise Editions The HP Web Jetadmin print management features are supported by the following o Windows XP Professional with Service Pack 2 or higher o Windows Server 2003 e HP Driver Deployment Utility The HP Driver Deployment Utility HP DDU was created to simplify the deployment of print drivers onto a client computer It is a simple utility that packages the printdriver files and the code needed to deploy them into two files an EXE file and a CAB file These files are run on the client computer to copy the print driver files to the Windows driver store and for network packages to install the product This utility is supported on Windows XP Windows Server 2003 Windows Server 2008 and Windows Vista operating systems To gain access to the HP DDU insert the software CD into the CD ROM
48. Viewer opens the file on the computer screen e Hypertext Markup HTM When you click a documentation link to an HTM document a Web browser opens the file on the computer screen e Rich Text Format RTF This is a text file You can navigate to files and open them in Microsoft Word or Microsoft WordPad Documentation for the HP LaserJet Pro CM1410 Color MFP Series is divided into the following categories e User documentation e Administrator documentation Documentation availability and localization 3 4 User documentation The following figure shows the Documentation screen which appears when you click More Options then Documentation on the main screen of the HP LaserJet Pro CM1410 Color MFP Series printing system software CD Figure 1 1 Installation software CD User Documentation screen Ap HP LaserJet Professional CM1410 Series Software Install User Guide CD Oo For information about product operation troubleshooting warranty and specifications use Adobe Acrobat Reader to view or print the User Guide that is on the CD More Options aS User Guide Web Online Admin Documentation For the most current information and expanded functionality see the User Guide on HP com Admin Software Readme Provides specific installation instructions and other information you should know before Get Specialized Drivers O you install and use the product software Web Support A Help and
49. Windows click Start click Run and then type cmd b Type ping followed by the service set identifier SSID for your network c If the window displays round trip times the network is working 3 Make sure that the router or product connects to the same network that your computer connects to a Open the Reports menu and select the Configuration Report item to print the report Compare the service set identifier SSID on the configuration report to the SSID in the printer configuration for your computer c If the SSIDs are not the same the devices are not connecting to the same network Reconfigure the wireless setup for your product ENWW Solve wireless network problems 201 Service mode functions Secondary service menu Use the secondary service menu to print service related reports and to run special tests Customers do not have access to this menu Open the secondary service menu 1 Touch the Setup amp button 2 Touch the middle of the screen along the left hand edge callout 1 and then immediately touch the lower right corner callout 2 of the screen 3 When the Home screen appears touch the Setup N button 4 Touch the 2ndary Service button to open the menu X TIP When you are finished with the 2ndary Service menu touch the lower right corner of the screen until the Job Settings Cleared message appears on the Home screen This step removes the 2ndary Service option from the Setup Menu Secondary ser
50. Windows driver store the HP DDU code will cleanup incomplete Plug and Play events for products supported by this print driver Then it will refresh the bus causing the operating system to Plug and Play the product installing the print driver and creating the printer object HP Driver Deployment Utility 51 How do I uninstall HP DDU Delete all the files in the root HP DDU directory NOTE No registry changes have been made with this utility 52 Chapter 2 Windows software description ENWW 3 ENWW Install Windows printing system components The HP LaserJet Pro CM1410 Color MFP Series comes with software and installers for Microsoft Windows and Apple Macintosh systems For information about Macintosh software see Macintosh software and utilities on page 111 Linux and UNIX systems support the HP LaserJet Pro CM1410 Color MFP Series and software is available on the Web This chapter provides procedures for installing and uninstalling the HP LaserJet Pro CM1410 Color MFP Series printing system software for Windows operating systems e Install overview e Software installation types for Windows e Installation options e General Windows installation instructions 53 Install overview The software for the HP LaserJet Pro CM1410 Color MFP Series product is available from the printing system software CD For all supported operating systems each install option presents a series of screens that guide you th
51. any command method that delivers the printready file to the product is acceptable including the following e At the command prompt type cp lt home yourmachine FILENAME dev parallel gt where lt home yourmachine FILENAME gt is the location of the print ready file Print ready file printing by using the LPR command amp NOTE This direct printing method is for use in Windows 2000 Windows XP Windows Server 2003 Windows Server 2008 and Windows Vista ENWW Printing print ready documents 241 Complete the following steps to print a printready file by using the LPR command 1 Make note of the TCP IP address on the Embedded Jetdirect page The HP Embedded Jetdirect page is the second page of the configuration page printout 2 From a command window type the following lpr P lt IPADDRESS gt S lt IPADDRESS gt o lt FILENAME gt or Ipr S lt IPADDRESS gt Pbinps lt FILENAME gt where IPADDRESS can be either the TCP IP address or the host name of the product and where FILENAME is the file name of the print ready file amp NOTE The parameter o l consists of a lowercase O not a zero and a lowercase L not the numeral 1 This parameter sets the transport protocol to binary mode 3 The file prints but no messages appear in the command prompt window 4 Type exit at the command prompt to close the command window 242 Chapter 7 Engineering Details ENWW Paper and print media e Media sour
52. buy a filter e Verify that the filter is plugged in e Replace the existing filter to make sure that it is not defective The product uses a fax over IP or VoIP phone service e Set the Fax Speed option to the Slow V 29 or Medium V 17 setting or disable the Fast V 34 setting From the Home screen touch the Setup button b Open the Fax Setup menu c Open the Advanced Setup menu d Open the Fax Speed menu e Select the correct setting e Contact your service provider to make sure that fax is supported and for a recommended fax speed settings Some companies might require an adapter An error message displays on the control panel The No fax detected message appears NOTE This error does not always refer to a missed fax If a voice call is made to a fax number by mistake and the caller hangs up the No fax detected message appears on the control panel e Ask the sender to resend the fax e Make sure that the telephone cord from the product is plugged into the wall telephone jack ENWW Solve fax problems 229 e Try a different phone cord e Plug the product phone cord into a jack for another phone line e Make sure the telephone line and phone wall jack are active by plugging in a telephone and checking for a dial tone e Make sure that the telephone cord is plugged into the line port on the product e Check the phone line by running a fax test from the control panel e If the error persists
53. connection verify the USB cable is connected between the product and the computer Turn on the product If you are installing using a network connection verify that the network cable is connected to the product and that the product is on 2 In the Applications folder in the Finder utility open the System Preferences folder and then open Printer amp Fax 3 If you are installing the product using a USB connection verify that the product appears in the printer list The Name column in the printer list should display the product name If this is the case the USB setup is complete If the product does not appear or if the correct information does not appear in the field see Troubleshooting the product setup on page 117 If you are installing the product using a network connection continue with the following steps 4 Click the add icon beneath the Printer List to open the Printer Browser screen 5 Select your product model from the list of printers with Bonjour as the Kind Click the Add button Troubleshooting the product setup ENWW If the product does not appear in the printer list after an installation Complete each one of these solutions in the order given and restart the setup process after each one to see if the issue has been resolved e Verify that the USB or network cable is connected between the product and the computer and that the product is powered on e Try disconnecting and reconnecting the cable If
54. controls the scale directly The value in the edit box changes as the slider bar indicator is dragged and the document preview image is updated to the new image scale Each click on the arrows increases or decreases the scale by 1 Each click on the slider bar affects the scale by 10 You cannot achieve an exact value by dragging the slider bar indicator Instead either use the slider bar indicator to approximate the value that you want and then use the arrows to refine the value or type the value into the entry box The following settings disable of Actual Size e Print Document On on the Effects tab is selected e Pages per Sheet on the Finishing tab is not 1 Document preview image The document preview image is a line drawn image of a page that represents graphics and text The document preview image is always oriented so that the contents of the page are right side up The document preview image appears in the upper right corner of the following Printing Preferences driver tabs e Printing Shortcuts e Paper Quality e Effects e Finishing e Color Switching between tabs does not change the location or appearance of the document preview image When you move the mouse over the document preview image the mouse cursor changes from an arrow to a gloved hand You can toggle between portrait and landscape page orientation by clicking the image Watermarks Use the Watermarks feature to select a watermark create a new watermar
55. ed ss Satie awed cla vee neen es 103 Paper SIZES Sesi ien ie de dass nadedenses Sandan E EE EES 104 RETELEI IE AA T E A E E E 104 Print n DOT SIS mss sce toes toe cone ii a e e E ak 106 Eco print Two sided Printing ssseseeeneseeeeoeieeeseseeessessseeneresssreenrresesssene 106 Factory Defaults ams ai E Beyond pnd A ER aac el 106 ERVEIODES n nongtot anni nonan e TATAE E OTa N NN NOR DA 106 vi ENWW Cardstock Hedyy orrien acne sien E ae 106 Glasey Precentalions 5 cuivscancvasannneaitaseusriaaduanians atieersvarsnecinnanetsenauiautnnned 107 Snapshot POISE demaeleerois taomindesensaredaua tem aerate ah una E 107 Le E ttn tena nae ti vin tititich chee lac chet Alcea el ln inci AA E 107 labels gee cesp tab tacecpe E E ete et E E AN E E 107 Create a custom printing shortcut sijc1c siadvacedvarenenianiaacerivaadauseatnrivdanueumsaaantseeen 107 Abot tab Te GROSS amirni acenion a ain pe Tera errien ine hava ated AEAEE E E A E E aE 109 5 Macintosh software and utilities ccccccsscssscccssccccesscccssccccscccscesccscscesssccessceescees 111 Supported operating systems for Macintosh cccesceeeeeseceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeseeesenaes 112 Macintosh system requirements i csc0csressnrenvsrorarannssaadsvassruhseborbosendsanddvaseseacenosnenuboonornsatnonasbonens 112 Hardware REG UIST IS sessirnir E mnenisconnek 112 Macintosh printing system software cccccccceesseceeeeenseeeeseeeeeeceeaeeeeeeeesee
56. error e Receive fax error e Never amp NOTE With this option you will have no indication that a fax failed to be transmitted unless you print a fax activity log From the Home screen touch the Fax button 2 Touch the Fax Menu button 3 Touch the Fax Reports button 4 Touch the Fax Error Report button and then touch the printing option that you want to use Change error correction and fax speed Set the fax error correction mode ENWW Usually the product monitors the signals on the telephone line while it is sending or receiving a fax If the product detects an error during the transmission and the error correction setting is On the product can request that the portion of the fax be resent The factory set default for error correction is On You should turn off error correction only if you are having trouble sending or receiving a fax and you are willing to accept the errors in the transmission Turning off the setting might be useful when you are trying to send a fax overseas or receive one from overseas or if you are using a satellite telephone connection 1 From the Home screen touch the Setup button 2 Touch the Service menu 3 Touch the Fax Service menu 4 Touch the Error Correction button and then touch the On button Solve fax problems 219 Change the fax speed The fax speed setting is the modem protocol that the product uses to send faxes It is the worldwide standard for full duplex
57. if needed 10T Full After setting the link speed the product automatically restarts 10T Half 100TX Full 100TX Half Restore Defaults 144 Chapter 6 Solve problems Resets all network configurations to their factory defaults ENWW Function specific menus The product features function specific menus for copying faxing scanning and using a USB flash drive To open these menus touch the button for that function on the control panel Copy Menu To open this menu touch the Copy button and then touch the Settings button E NOTE Settings that you change with this menu expire 2 minutes after the last copy completes Menu item ID Copy NOTE This item is available from the main Copy screen You do not need to touch the Settings button to Sub menu item Sub menu item Description Copies both sides of identification cards or other small size documents onto the same side of one sheet of paper access it Number of Copies 1 99 Specifies the number of copies Reduce Enlarge Original 100 Specifies the size of the copy Legal to Letter 78 Legal to A4 83 A4 to Letter 94 Letter to A4 97 Full Page 9 1 Fit to Page 2 Pages per Sheet 4 Pages per Sheet Custom 25 to 400 Lighter Darker Specifies the contrast of the copy Optimize Describe Original Auto Select Specifies the type of content Mixed Text Picture in the original document so the copy is the best match fo
58. is set to Landscape for a driver originally installed in Windows XP then the orientation setting automatically remains Landscape when the operating system is upgraded to Windows Vista Windows Server 2003 or Windows Server 2008 The continuous export feature functions transparently from the user s perspective and works only between print drivers of identical product models NOTE Notall of the driver parameters can be exported however the exportable components are always the same as the components that can be preconfigured The following table shows drivers and operating systems that support HP Driver Configuration Table 2 5 Operating systems that support HP Driver Preconfiguration Driver Windows Windows Windows Windows Windows7 Mac OS X v10 5 Linux XP Server Server Vista and later 2003 2008 HP PCL 6 Yes Yes Yes Yes Yes NA NA Print Driver HP PCL 5 Yes Yes Yes Yes Yes NA NA Universal Print Driver HP PS Yes Yes Yes Yes Yes NA NA Universal Print Driver TNA Not app icable the driver is not supported in this operating system Driver configuration for Windows 25 HP Driver Diagnostic Printer Check Tool 26 The HP Driver Diagnostic Printer Check Tool is a Web based diagnostic software that you can use to determine whether you are using the correct and most current Windows print driver for the HP LaserJet Pro CM1410 Color MFP Series product Two methods are available to gain access to the HP Driver Diagnostic Printer Chec
59. it If the error persists try the following solutions A Clean the roller Door open Description The print cartridge door is open Recommended action Close the print cartridge door Engine Communication Error Description The product has experienced an engine communication time out error Recommended action Turn off the power by using the power switch wait at least 30 seconds and then turn on the power and wait for the product to initialize If a surge protector is being used remove it Plug the product directly into the wall socket Use the power switch to turn the product on Engine error Press OK to continue Description The product experienced a print engine error Recommended action This is a warning message only Job output might be affected Fax is busy Canceled send ENWW Description The fax line to which you were sending a fax was busy The product has canceled sending the fax Recommended action Call the recipient to ensure that the fax machine is on and ready Tools for troubleshooting 157 Check that you are dialing the correct fax number Check that the Redial if Busy option is enabled Open the Service menu and touch the Fax Service button Touch the Run Fax Test button This test verifies that the phone cord is connected to the correct port and that the phone line has a signal The product prints a report with the results Fax is busy Redial pending Description The fax line to wh
60. line around each page image on a printed sheet to help visually define the borders of each logical page Page Order The Page Order drop down menu contains four selections e Right then Down e Down then Right e Left then Down e Down then Left Document preview image The document preview image is a line drawn image of a page that represents graphics and text The document preview image is always oriented so that the contents of the page are right side up The document preview image appears in the upper right corner of the following Printing Preferences driver tabs e Printing Shortcuts e Paper Quality e Effects 90 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW e Finishing e Color Switching between tabs does not change the location or appearance of the document preview image When you move the mouse over the document preview image the mouse cursor changes from an arrow to a gloved hand You can toggle between portrait and landscape page orientation by clicking the image Orientation Orientation refers to the layout of the image on the page and does not affect the way that paper feeds into the product You can specify the orientation of the print job The three available orientations are portrait landscape and rotated The default orientation is Portrait E NOTE Nearly all software programs establish the orientation for the printed page so the page orientation in the driver is us
61. listed in the USB Flash Drive menu 1 You might be trying to print a file type that the USB printing feature does not support The product supports PDF and JPEG file types 2 You might have too many files in a single folder on the USB storage accessory Reduce the number of files in the folder by moving them to subfolders 3 You might be using a character set for the file name that the product does not support In this case the product replaces the file names with characters from a different character set Rename the files using ASCII characters ENWW Solve walk up USB printing problems 195 Solve connectivity problems Solve direct connect problems If you have connected the product directly to a computer check the cable Verify that the cable is connected to the computer and to the product Verify that the cable is not longer than 5 m 16 4 ft Try using a shorter cable Verify that the cable is working correctly by connecting it to another product Replace the cable if necessary Solve network problems Check the following items to verify that the product is communicating with the network Before beginning print a configuration page from the product control panel and locate the product IP address that is listed on this page Poor physical connection The computer is using the incorrect IP address for the product The computer is unable to communicate with the product The product is using incorrect link and d
62. modems that send and receive data across telephone lines at up to 33 600 bits per second bps The factory set default for the fax speed setting is Fasi V 34 You should change the setting only if you are having trouble sending a fax to or receiving a fax from a particular device Decreasing the fax speed might be useful when you are trying to send a fax overseas or receive one from overseas or if you are using a satellite telephone connection From the Home screen touch the Setup button 2 Touch the Fax Setup menu 3 Touch the Advanced Setup menu 4 Scroll to and touch the Fax Speed button and then touch the speed setting that you want to use Solve problems sending faxes e An error message displays on the control panel e The control panel displays a Ready message with no attempt to send the fax e The control panel displays the message Storing page 1 and does not progress beyond that message e Faxes can be received but not sent e Unable to use fax functions from the control panel e Unable to use speed dials e Unable to use group dials e Receive a recorded error message from the phone company when trying to send a fax e Unable to send a fax when a phone is connected to the product An error message displays on the control panel The Communication error message appears 220 e Allow the product to retry sending the fax Re sending temporarily reduces the fax speed e Unplug the
63. only e HP LaserJet Send Fax Application multifunction products only e HP LaserJet Fax Setup Utility multifunction products only e HP LaserJet Fax Driver multifunction products only For information about Linux printer drivers go to www hp com go linux For information about UNIX printer drivers go to www hp com go jetdirectunix software OVERVIEW OF THE PRINTING SYSTEM COMPONENTS The Windows CD ROM has software for IBM compatible computer systems For more information about a particular driver or software component see its associated online help Drivers A driver is software that allows software applications to access product features Typically you should install drivers for each product The printing system software CD ROM that came with your device includes the following Windows drivers e HP PCL6 print driver for the supported operating systems listed above e HP WIA Scan driver that includes TWAIN compatibility Software Applications e HP ToolboxFX e HP LaserJet Help and Learn Center provides access to the product user guide and troubleshooting information e Uninstaller Additional drivers might be available from your Hewlett Packard distributor or from online sources See the Technical Assistance section of this document or the product user guide for more information about obtaining drivers and other HP software 246 Chapter 7 Engineering Details ENWW HP ToolboxFX The printing system software
64. or For Windows XP Home Click Control Panel and then double click the Printers and Other Hardware icon or For Windows Vista Click Computer click Control Panel and then click Hardware and Sound 2 Click Add Printer and then click Next 3 When asked if the product is a local or network product select Local printer attached to this computer and then click Next NOTE Do not select the Automatically detect and install my Plug and Play printer option 4 On the Select a Printer Port screen select the USB Print port that was created by a previous USB installation and then click Next 5 On the Install Printer Software screen click Have Disk The Install from Disk dialog box appears 6 Insert the printing system software CD into the CD ROM drive 7 Click Browse and then select the printer driver for the product To install the PCL 6 printer driver navigate to the root folder of the CD where X is the letter of the CD ROM drive and select the hppdp608 inf file 56 Chapter 3 Install Windows printing system components ENWW To install the HP postscript level 3 emulation printer driver navigate to the appropriate folder and select the appropriate file e For 32 bit Drivers win2k_xp_vista hppcps08 inf e For 64 bit Drivers winxp_vistax64 hppdps08 inf 8 Click Open 9 On the Install from Disk dialog box click OK 10 Click Next Complete the installation When prompted print a test page to en
65. place liquids directly on the glass or platen They might seep and damage the product 4 Dry the glass and white plastic backing with a chamois or a cellulose sponge to prevent spotting 5 Plug in the product and then use the power switch to turn on the product ENWW Improve print quality 189 Clean the product Clean the exterior Use a damp lintfree cloth to wipe the exterior of the product Clean the paper path During the printing process paper toner and dust particles can accumulate inside the product Over time this buildup can cause printquality problems such as toner specks or smearing This product has a cleaning mode that can correct and prevent these types of problems Clean the paper path from the product control panel 1 From the Home screen touch the Setup N button Touch the Service menu Touch the Cleaning Page button Load plain letter or A4 paper when you are prompted 5 Touch the OK button to begin the cleaning process A page feeds no the product slowly Discard the page when the process is completed Clean the scanner glass strip and platen Over time specks of debris might collect on the scanner glass and white plastic backing which can affect performance Use the following procedure to clean the scanner glass and white plastic backing 1 Use the power switch to turn off the product and then unplug the power cord from the electrical socket 2 Open the scanner lid 190 Chapte
66. print cartridges e Number of pages printed e Information about ordering new HP print cartridges and recycling used HP print cartridges Network Summary Displays status for e Network hardware configuration e Enabled features e TCP IP and SNMP information e Network statistics e Wireless network configuration wireless models only Usage Page Displays the number of pages printed faxed copied and scanned by the product PCL Font List PS Font List Prints a list of all installed PCL 5 fonts Prints a list of all installed PS fonts PCL6 Font List Prints a list of all installed PCL 6 fonts Color Usage Log Prints information about the color supply usage Service Page Prints the service page The service page includes information about supported paper types copy settings and other settings that are not included on the configuration page Diagnostics Page Prints diagnostic information about calibration and color quality Print Quality Page Prints a page that helps solve problems with print quality 134 Chapter 6 Solve problems ENWW Quick Forms menu ENWW Menu item Sub menu item Description Notebook Paper Narrow Rule Prints pages that have preprinted lines Wide Rule Child Rule Graph Paper 1 8 inch Prints pages that have preprinted graph lines 5 mm Checklist 1 Column Prints pages that have preprinted lines with check boxes 2 Column Music Paper Portrait P
67. prioritized depending on where the changes are made E NOTE The names of commands and dialog boxes might vary depending on your software program e Page Setup dialog box Click Page Setup or a similar command on the File menu of the program you are working in to open this dialog box Settings changed here might override settings changed anywhere else e Print dialog box Click Print Print Setup or a similar command on the File menu of the program you are working in to open this dialog box Settings changed in the Print dialog box have a lower priority and do not override changes made in the Page Setup dialog box e Default printer driver settings The default printer driver settings determine the settings used in all print jobs unless settings are changed in the Page Setup Print or Printer Properties dialog boxes e Printer control panel settings Settings changed at the printer control panel have a lower priority than changes made anywhere else ENWW Macintosh printing system software 113 Change printer driver settings for Macintosh Change the settings for all print Change the default settings for Change the product configuration jobs until the software program all print jobs settings is closed 1 On the File menu click Print 1 On the File menu click Print 1 From the Apple menu click System Preferences and then 2 Change the settings that you want 2 Change the settings that you want Print amp Fax on the various
68. product phone cord into a jack for another phone line Check the phone line by using the Run Fax Test option from the Service menu on the control panel a From the Home screen touch the Setup N button b Open the Service menu c Open the Fax Service menu d Select the Run Fax Test item The Fax is busy message appears ENWW Try sending the fax again Call the recipient to ensure that the fax machine is on and ready Check that you are dialing the correct fax number Solve fax problems 221 Check for a dial tone on the phone line by using the Start Fax button Make sure that the phone is working by disconnecting the product plugging in a telephone to the phone line and making a voice call Plug the product phone cord into a jack for another phone line and try sending the fax again Try a different phone cord Send the fax at a later time If the error persists contact HP See www hp com support CM141Oseries or the support flyer that came in the product box The No fax answer message appears Try to resend the fax Call the recipient to ensure that the fax machine is on and ready Check that you are dialing the correct fax number Unplug the product telephone cord from the wall plug in a telephone and try making a voice call Plug the product phone cord into a jack for another phone line Try a different phone cord Make sure that the phone cord from the wall telephone jack is plugged into the line J
69. sae nem ee ace eee een ee ee ttt Stt ESSE ee ene eee recat ene terete ee 96 Figure 4 9 Device Settings tab eiccin ienei ien 98 Figure 4 10 Printing Shortcuts tab ccccceeccenceceeneeeeeneeeceeeeseaeeeseeeeseaeeesneeeseeeeseneeeseeeeseaeeess 102 Figure 4 11 ABOUR tal cosctieicceiesiesspian cs eieeaita cia e N E E 109 ENWW xvii xviii ENWW 1 Document and product basics e Purpose and scope e Documentation availability and localization e Software availability and localization ENWW 2 Purpose and scope This software technical reference STR provides information about and troubleshooting tips for the printing system software for the product This STR is prepared in an electronic format to serve as a quick reference tool for Customer Care Center CCC agents support engineers system administrators management information systems MIS personnel and end users as appropriate NOTE This STR describes drivers that are available from the product firmware and shipped on the printing system software CD that comes with the product This STR does not describe drivers that will become available on the Web The following information is included in this STR e Descriptions of drivers operating systems and system environments e Descriptions of installing and uninstalling the printing system software components For information about the location of information within chapters see the table of contents An index i
70. sending disconnect The sending product is probably transmitting sync frames instead of data and has either jammed or broken 283 284 The receiving product has detected that the modem carrier has stopped Either the line has been disconnected or the sending product has aborted the transmission The receiving product has not received any data during non ECM page reception and a timeout failure has occurred The sending product is probably transmitting fill bytes instead of data and has either jammed or broken 285 286 The receiving product has stopped receiving any data during an ECM page reception although the modem has not detected a sending disconnect The sending product is probably transmitting sync frames instead of data and has either jammed or broken The sending product has transmitted invalid data The receiving product has received frames with errors during an ECM reception and requested retransmission of the errored frames The data that is resent does not correspond to the data that was requested This is an implementation error from the sending product Reattempt the fax reception after first requesting that the sender check the sending product Disable ECM and reattempt the reception 290 The sending product has attempted to renegotiate the session mode from ECM to non ECM between pages This operation is not supported and the session has been abandoned Reattempt the fax reception and spl
71. software program click Print Select the product and then click the Properties or Preferences button Click the Paper Quality tab From the Paper type drop down list click the More option Expand the list of Type is options Expand each category of paper types until you find the paper type that you are using Select the option for the type of paper you are using and click the OK button Change the paper type setting for Mac 1 2 3 ENWW On the File menu in the software program click the Print option In the Copies amp Pages menu click the Page Setup button Select a size from the Paper Size drop down list and then click the OK button Improve print quality 179 4 Open the Finishing menu 5 Select a type from the Media type drop down list 6 Click the Print button Adjust color settings in the printer driver Change the color theme for a print job 1 2 3 4 On the File menu in the software program click Print Click Properties or Preferences Click the Color tab Select a color theme from the Color Themes drop down list TARGET NOT FOUND Default SRGB This theme sets the product to print RGB data in raw device mode When using this theme manage color in the software program or in the operating system for correct rendering Vivid The product increases the color saturation in the midtones Use this theme when printing business graphics Photo The product interpret
72. take place and the copies values are treated independently For these programs setting 10 copies in the program and then setting 10 copies in the driver will result in 100 copies 10 x 10 being printed It is recommended that you set the number of copies in the program whenever possible When the Copy Count option is set to more than 1 the Collated check box becomes available Select this check box when you want the product to collate the printed copies Most current software programs support the collating feature in the print dialog box or through the page settings in the software program Graphic The Graphic setting contains the following controls e Image Color Management settings e True Type Font settings Image Color Management This control lists the available Image Color Management ICM options used for printing color graphics ICM a set of calculations for color matching makes it possible for programs to adjust colors before printing so that the color of images on the screen more closely match the color of those images when they are printed E NOTE The ICM control is typically set to ICM Disabled True Type Font ENWW Use Substitute with Device Font the default setting to print documents that contain TrueType fonts by using equivalent printer fonts This permits faster printing however you might lose special characters that the equivalent printer font does not support Select Download as Softfont to download True
73. the font The Font Attributes group box contains the following controls e Name The Name drop down menu lists fonts that are currently installed on the system The default is language dependent e Color The Color drop down menu contains the following selections Gray gt Red o gt Yellow gt Green o gt Cyan o gt Blue gt Magenta e Shading 82 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW The default Shading setting for new and preset watermarks is Very Light The following range of shades is available from the Shading drop down menu o o Lightest Very Light default Light Medium Light Medium Medium Dark Dark Very Dark Darkest These values represent the intensity of the gray that is used Select Light to produce a lightly saturated gray watermark Select Lightest to produce the lightest shade of watermark Select Darkest to produce a black watermark e Size Font sizes from 1 to 999 points are available from the Size menu The default point size is language dependent e Style The following settings are available o Regular Bold Italic Bold Italic The default Style setting for new and preset watermarks is Regular Default watermark settings ENWW The following table shows Font Attribute settings for new and preset watermarks Table 4 1 Font Attribute settings for new and preset watermarks Setting New watermark Preset waterma
74. the receiving product even though receiving a document Check that paper is the capability to receive is disabled at the correctly loaded paper is not jammed within the receiving product product and any other system abnormalities have been cleared 232 One of the following has occurred 1 Re attempt the fax reception at a different time when telephone line conditions have 233 and 234 e A communication failure has occurred 235 and 236 ECM between the two products improved 2 If the error persists and error correction is in error e The user at the remote product may have use for the fax session disable ECM touched the Cancel X button 237 e The power at the remote product has been interrupted or deliberately turned off causing the fax session to be interrupted 238 The sending fax product sent an unexpected N A communication This is a defect in the sending 239 241 product 242 The sending fax product is attempting to receive Ensure that a document is ready and correctly instead of send Both products have attempted to start a reception at the same time It is possible to accidentally initiate a fax reception after dialing on many products if there is no paper in the product or if the paper is not correctly loaded and cannot be sensed by the appropriate document sensor loaded in the sending fax product and that the sending product is attempting to initiate a transmission and not a reception ENWW
75. the wireless access point 2 Make sure the product is turned on and in the ready state 3 Turn off any third party firewalls on your computer 4 Make sure that the wireless network is working correctly a On the product control panel open the Network Setup menu and then open the Wireless Menu item b Select the Run Network Test item to test the wireless network The product prints a report with the results 5 Make sure that the correct port or product is selected a From the list of printers on your computer right click the name of this product click Properties and then open the Ports tab b Click the Configure Port button to verify that the IP address matches the IP address listed on the Run Network Test report 6 Make sure that your computer is working correctly If necessary restart your computer The wireless product loses communication when connected to a VPN e Typically you cannot connect to a VPN and other networks at the same time The network does not appear in the wireless networks list e Make sure the wireless router is turned on and has power e The network might be hidden However you can still connect to a hidden network 200 Chapter 6 Solve problems ENWW The wireless network is not functioning 1 To verify if the network has lost communication try connecting other devices to the network 2 Test network communication by pinging the network a Open a command line prompt on your computer For
76. then resend the fax The control panel displays a Ready message with no attempt to send the fax e Check the fax activity log for errors Touch the Fax button and then touch the Fax Menu button Open the Fax Reports menu c Open the Fax Activity Log menu d Select the Print Log Now option e Ifa phone is connected to the product make sure that the phone is hung up e Disconnect all other lines between the fax and the product e Connect the product directly into the wall telephone jack and resend the fax ENWW Solve fax problems 223 The control panel displays the message Storing page 1 and does not progress beyond that message Delete stored faxes from memory a From the Home screen touch the Setup N button Open the Service menu c Open the Fax Service menu d Select the Clear Saved Faxes item Faxes can be received but not sent Send fax and nothing happens 1 2 3 Check for a dial tone on the phone line by using the Start Fax button Turn the product off then on Use the control panel or the HP Fax Setup Wizard to configure the fax time date and fax header information a From the Home screen touch the Setup N button Open the Fax Setup menu c Open the Basic Setup menu d Open the Fax Header menu e Enter the correct settings Verify that any extension phones on the line are hung up If using a DSL service make sure that the phone line connection to the product includes a high pass filter
77. they didn t intend to like the root directory Some print drivers are really large and you can choose to ignore this warning and continue To minimize package size each print driver should be in it s own directory This is usually the default behavior when you expand a print driver I get an error when I try to open the Network Settings dialog You need to first select a print driver before opening the Network Settings dialog This populates the product name field based on the printer driver name The Create Package button is not enabled This button will not be enabled until you have 1 Selected the print driver 2 If network connect filled out one of the required network settings 3 Selected the Save as name and directory How do I exit the HP DDU Use the Windows close button in the upper corner The Network Settings dialog keeps displaying an error and I just want out If you do not want to save settings or change your mind and don t want a network install you need to close the network settings dialog with the Windows close button in the upper corner Using the OK button will try to validate the settings and that is what is causing an error What if the user connects the printer before the HP DDU package is run If the user connects the product but then cancels the Plug and Play event before it finishes this creates an incomplete Plug and Play event After copying the printer driver files to the
78. to configure the print driver after it is installed This does not break WHQL certification If the print driver was WHQL certified and the print driver files are organized within one directory structure then HP DDU will not break WHQL certification HP DDU packages all of the files found in the printer driver directory structure without modifying them If printer driver pre configuration is done the new configuration file is used to configure the print driver after it is installed This does not break WHAL certification NOTE If you need the ability to configure unique settings for printer driver deployment the Universal Print Driver installer may be a better choice as an install tool The Universal Print Driver installer allows the configuration of settings from the command line The HP DDU can be used with the Universal Print Driver installer but the Universal Print Driver command line will not be accessible The HP DDU is designed to package and stage install print drivers Print driver specific features like those found in the Universal Print Driver installer are specific to the Universal Print Driver installer and not supported by the HP DDU The HP DDU installer could be used with the Universal Print Drivers to deploy a direct connect driver in traditional mode or a network install in traditional mode NOTE Administrative rights are necessary on the client system where the install is being performed For a direct conn
79. to use different configuration settings toggle the ECM state and or select a slower reception speed 223 ECM error The receiving product has been unable to receive an entire page even after multiple attempts to re receive the parts of the page that contain errors This is usually due to extremely poor line conditions 1 Reattempt the fax reception at a different time when telephone line conditions have improved 2 Ifthe error persists disable ECM Errors may still occur and may result in degraded image quality on the received page However the ability to receive the entire document will be improved 224 225 The receiving product has received one or more pages with excessive errors This is usually due to extremely poor line conditions Error correction is not used during this session so errors are not corrected The sending product has attempted to initiate a sending diagnostic session with this product even though sending diagnostic access is disabled Reattempt the fax reception at a different time when telephone line conditions have improved Enable the sending diagnostics capability on the receiving product Chapter 6 Solve problems ENWW Table 6 4 Fax receive error codes continued Error code Description Solution 226 The sending product has attempted to initiate a None Sending diagnostics cannot occur between sending diagnostic session with this product but the produc
80. while trying to send a fax Recommended action Try resending the fax Try faxing to another fax number Check that the telephone cord is securely connected by unplugging and replugging the cord Make sure that you are using the telephone cord that came with the product Open the Service menu and touch the Fax Service button Touch the Run Fax Test button This test verifies that the phone cord is connected to the correct port and that the phone line has a signal The product prints a report with the results Connect the product to a different phone line Set the fax resolution to Standard instead of the default of Fine Fax storage is full Canceling the fax receive Description The amount of available memory for storing faxes is insufficient to store an incoming fax Recommended action If you are using the Private Receive feature print all received faxes to regain some memory If you still need more memory clear faxes from memory Open the Service menu In the Fax Service menu select the Clear Saved Faxes option Fax storage is full Canceling the fax send Description During the fax job the memory filled All pages of the fax have to be in memory for a fax job to work correctly Only the pages that fit into memory were sent Recommended action Cancel the current job Turn the product off and then turn it on again Try sending the job again If the error reoccurs cancel the job and turn the product off and then on a second ti
81. 114 Macintosh requirements 112 NVRAM initialization 204 menu control panel access 133 copy 145 fax 146 Fax setup 136 Network config 144 Quick Forms 135 Reports 134 Service 142 System setup 139 USB 150 menu map printing 170 messages control panel 151 messages constraint print drivers 64 Microsoft Outlook 32 model comparison 1 music paper printing 135 N network configuring 144 device polling 131 Network config menu 144 Network Settings tab HP ToolboxFX 131 networks direct printing 241 HP Driver Configuration 23 HP Jetdirect Guide 6 Point and Print installation 59 notebook paper printing 135 Novell Netware operating systems Enterprise AutoConfiguration support 22 NVRAM initialization 204 O OCR file types supported 29 Windows software 17 online help Windows 17 256 Index operating systems Enterprise AutoConfiguration support 21 supported Macintosh versions 112 Outlook 32 output quality HP ToolboxFX settings 130 repetitive image defects 187 P package creation suppress user error messages 48 pages blank or preprinted 75 paper adding custom types 74 Alternative Letterhead Mode 69 custom sizes 72 default settings 130 duplex binding settings print drivers 88 HP ToolboxFX settings 130 jams 171 orientation 91 selecting 182 settings print drivers 70 source commands 243 source setting 72 sources and destinations 243 type commands 244 type setting 73 paper pickup problems solving
82. 171 paper type changing 179 parameters fax data store 244 PBX ring detect 203 PCL 5 UPD media source commands 243 PCL 6 printer driver media source commands 243 PCL files command line printing 238 PCL settings HP ToolboxFX 131 PDF files command line printing 238 LPR commands printing 241 viewing 3 PDF files online help 17 phone book fax HP ToolboxFX tab 126 Point and Print installation Windows printing system software 59 polling device 131 PostScript Printer Description PPD files included 114 PostScript settings HP ToolboxFX 13 PPDs Macintosh troubleshooting 117 pre existing installation modifying 60 print cartridges checking for damage 186 status viewing with HP Toolbox FX 125 print density settings 130 print driver supported operating systems 18 print drivers About tab contents 109 access 62 Advanced Printing Features settings print drivers 68 Advanced tab content 66 Allow Manual Duplexing setting Device Settings tab 101 Alternative Letterhead Mode Advanced tab 69 Automatic Configuration setting Device Settings tab 101 Automatic settings Color tab 93 Booklet Layout settings Finishing tab 89 Color Options settings Color tab 93 Color tab contents 92 Color Themes settings Color tab 94 continuous export 25 ENWW Copy Count settings Advanced tab 67 device services Services tab 97 Device Settings tab content 98 Document Options setting Advanced tab 68 Document Options setting
83. 2 15 4 cclvvorrdeassvaecedvvoervatudedeeeese vere 155 COMMUNIEGHON Er or sei eea a e a a N 155 Cyan Cartridge LOW snc ci eidiacede eae eae eee annie aa umeens 155 Cyan in wrong position as cawetact mets Acta tant adeaanets 155 Cyan Very LOW seccscunerscvses aaee gee Ea EE EE TE EEE RTE EEEE 156 Device error press OK fies cece eid aed davedeeedsdeeedlavedeeets 156 Device is busy Try again later cccceeessseecceeeeeeeeeeeeeeeeeeeeees 156 Document feeder jam Clear and reload cccccceeeeeseeeeeeeees 156 Document feeder mispick Reload cccccccceeeesseeeeeeeeeteeeeeeaes 157 Door opem eaea aE bes caved A gbeecate a a E 157 Engine Communication Error cccceecccceeeeeeeeeceeeceeeeeeeeeees 157 Engine error Press OK to Continue seeeeeeeeeeeeeeeeeeeeeeeeeees 157 Fax is busy Canceled send ccd an cnasded sstvonsen de qeduyonnetinenoaetd aaatas 157 Fax is busy Redial pending oucsuutoun Anise 158 Fax receive error nosenie iesit ga e e eine Ea AE 158 Fax Send errori cheas a e a a R 159 Fax storage is full Canceling the fax receive ecceeeeseeeeeteeeees 159 Fax storage is full Canceling the fax send cccceeseeeeeeeeeees 159 Fit to Page on flatbed only cccecssceeeeeseeeeeseteeeeeeeteeeeeeaes 159 Install color cartridge jasc cour cvrawyac ade rn twucareccom uc enieacameates 160 Invalid driver Press OK 3 002 cocinapasn oneohperaeean ce viguantaneinias Buat ies 1
84. 60 Inyalidentry a eee ind osetia wnt Aap ete Re 160 Jam in area Open door and clear jam eecseeeeeeeeeeeeeeeeees 160 Jam in Tray 1 Clear jam and then press OK 000eeeeeeeeeeee 160 l da paperon Siac ins e e EN 161 Load Tray 1 lt TYPE gt lt SIZE gt Press OK to use available media 161 Load Tray 1 lt PLAIN gt lt SIZE gt Cleaning mode OK to start 161 Magenta Cartridge LOW o atcniciacadieencrenoenaiehanteves ulonantv wena 161 Magenta in wrong position ececcceceeeeeeeeeeceeeeeeaeeeeeeeeeenees 161 Magenta Very LOW auescasccibecerthsreceuneeatees cieasadsanchuueceuuseaceesteness 16 Manual Duplex Load Tray 1 Press OK cccecceceeceeeeceeeeeeeeeees 162 Manual feed lt SIZE gt lt TYPE gt Press OK to use available media 162 Memory is low Try again later vecccshaeuanscindancatuianes ainadeacnsaee 162 Memory is low Press OK sssssnnsssssssseesetressererterssssssereerrresse 162 Memory low Only 1 copy made Press OK to continue 00 163 Misprint Press OK a a a a A A eeu ea aa 163 Ne dial fone srunsa naan a E a e esea 163 No fax answer Canceled send sccancomcerunacaprareunnrgarscoummunaaneere 164 No fax answer Redial pending cceccceeeeeeeteeeeeeeseeeeeeaes 164 No fax detected ircrsscitaniaconitean deenaniseaaguadtecnanmsaniawbin mone 164 Print failure press OK If error repeats turn off then on 0 165 Replace
85. A sending fax product has failed to answer the Confirm the sending fax product is ready to call Specifically fax tones or the fax handshake receive a document and reattempt the from a sending product has not been detected transmission Typically this is due to the user calling the wrong number the correct number has been called but the product has been configured not to answer or the sending product has temporarily disabled answering due to a condition such as lack of paper or a paper jam 313 A busy signal has been detected each time the Reattempt the fax transmission at a later time when receiving product has attempted to call the sending the line is no longer busy product 314 The receiving product has attempted to initiate a Enable sending diagnostics on the sending sending diagnostic session but has detected that product sending diagnostics are disabled at the sending product 315 The receiving product has attempted to initiate a No solution Sending diagnostics cannot occur sending diagnostic session but has detected that the sending diagnostic version supported by the sending product is incompatible between products with incompatible sending versions Chapter 6 Solve problems ENWW Table 6 5 Fax send error codes continued Error code Description Solution 316 The receiving product is setup to initiate document Configure the sending product for reception transmission but it has detected that the sen
86. AQE ccecccecceceeaeeeeeeeeeeeeeeeceececcececeeeeeeaaaaaaaeeteeeeeeecereeeeeeeeeeeaas 95 Services tab fedf res neee eA e E E E E E E a E E E E Roe 96 Internet Services ereer ead aeaatanaetla diate dedod do dnehedaaeadeans deccutee edsngoaghtaninta tts tndvauaevaudeenseeh ees 97 DEVICE STV ICES 5 puss silo Gu sdastesaivade Sines td cite sin inteute eye edavones td cteti ios ete endeataat cde ate 97 Device Settings tab features ohh cn ctadod pecan wna eens aint nee nt monneueaawuntns 98 Form to Tray Assignment pectine case e A E EE deats dance EE EEEE 98 Font S bstit tion Table esseen n a a A E a none 99 External FOnis sisuteiskwuieasseedghaonebiag aiara a EE a nn EA 99 Installing external fonts cy dicusdevgxssceesiceew atts nese edatotsan Manenclaniecs 100 Removing externalitonts Cicie makina naloniie waned 100 InstallablE HONS neie E A A EA dun tvgaartaomanmehanens 100 Automatic Configuration sss ssssseeessseeessoesesetresetrerseetrsssrerresressseeererseee 101 Allow Manual Duplexing sisinivoisuaudevscnniwsurt olouanet olpinunvoisiacagubbatols kaskteovsthus 101 VOB S p rafor z tee e andere ones See cesd poset nouns E E ERES 101 Printing Sharteutstab teatires sunset anioercarevormrunioasneneciwala sworn wr a ee toe 102 Use defined printing shortcuts 1 stia cic tath street ind Mcedwuantauntneuteuen es 103 General Everyday Printing vcs kaetenccun ghekeatetar tnd cet eamraneacamenmealets 103 PaperSOUrCO 20 Sie cer ciet Savedende eo
87. Compression feature Advanced tab 69 Resizing Options settings Effects tab 79 Send True Type as Bitmap setting Advanced tab 68 Services tab content 96 True Type font settings Advanced tab 67 version numbers 18 Watermarks settings Effects tab 80 What s this Help 64 print job job separator 101 print on both sides manually 86 supported products print quality HP ToolboxFX settings improving 179 repetitive image defects print quality page interpreting 185 printing 185 Print Settings tab HP ToolboxFX 131 106 130 187 print ready files command line printing 238 printing by FTP 238 printing by local Windows port 240 printing by Windows network 241 printing in UNIX systems 241 printing with LPR command 241 printer drivers change Macintosh settings 114 choosing 188 Macintosh 112 Macintosh settings 113 media supported 244 mediatype commands 244 printing configuration page 132 direct in a Windows network 241 direct in UNIX 241 direct using FTP 238 direct using local Windows port 240 direct using LPR command 241 Printing Shortcuts tab paper size options paper type options printing system software availability 7 priority settings 113 problem solving control panel messages 151 no response 193 slow response 194 product model comparison 1 protocol settings fax 220 PS emulation fonts 40 PS files command line printing 238 104 104 Q quality HP ToolboxFX settings repetitive image defects 130 187
88. E aAA EAEE EPA EEEE EE ROE e 196 Solve directconnect problems ais ein ad Ati iPoic vnc en wk yeahs Baa od vey eo Rao ni 196 Solve network problems jiProvsthicoieetoiroerarsadureonde opiducrieuawdrsee onebbrsdouryowibebeanenes 196 Poor physical connecttonnc auc tus devas ovectetiad Moucnlasied eee paudeonene 196 The computer is using the incorrect IP address for the product sceeee 196 The computer is unable to communicate with the product ccceeeeeeeeeeeeees 197 The product is using incorrect link and duplex settings for the network 197 New software programs might be causing compatibility problems 197 The computer or workstation might be set up incorrectly 0 ccceeeeeeeeeeeeeees 197 The product is disabled or other network settings are incorrect 060000e 197 Solve wireless network problems uwiacreaed ceecnterndsseas Ma hindatr ad Maha ecaduenewean 198 Wireless connectivity checklist iccilatautzcentebvacsancntanass sarin cvadeaeadonesemtbnndeadun ain 198 The control panel displays the message The wireless feature on this product has been t rned ofi eea a a a e a tant wad baat nacctn den 199 The product does not print after the wireless configuration completes scseeeeee 199 The product does not print and the computer has a third party firewall installed 199 The wireless connection does not work after moving the wireless router or product 199 Cannot connec
89. EREE 72 Custom width and height control limits ccceseeeseeeeeeeeenteeeees 72 Paper SOU ICE ive inoen e E ee A 72 Papertype susene nio UE E IRIE A E eG R E S ome 73 Special pages sarne A nina tga nade 74 E T A E 75 Print pages on different paper 7 j caso vesnercnee oil eodegenawladuhe agents 75 Insert blank or preprinted pages cseeeeeceeeeeeteeeeeeeeesteeeeeeeeeees 75 Chapter separator pages weiss savietuetine andentntontanhond anasas 76 Documentipreview image eeneioe ir o EEE E E EEE EEO E E EAE a 76 Print Ojal res nienia e a E ace E E E EE 76 Print Quality drop down menu cceeccecceceeeesneeeeeeeeeseseeeeeeeeeeensseeeeeeeeess 77 Effects tabi features snn ea i n ea aE Ee ere are a aTa Eae E AEE RER 78 Resizing Options aniei e e a ciel da tne RN a ea a 79 PRI SIZE sxc ian cu eke septs ate eee ated Gace e E EAEE E N 79 Print Document Ons eese ea E E E A EES 79 Saleto Fib sesono noe en a asr Sata A E N A E 79 es OU RCH S1Z eid on at a e e e aud E 79 Document preview iMAge cecceceeceeeeeeeeeeeeececeeececececeeaaaeeaaaeeeeeeeeeeeeeeeeeeeeeeeeeaaaaeea 80 Watermarks issie lah Sed id aly O iat Te al Na Ses adieu a SO ence 80 Current watermarks 1541 od saratendattustetnactanac wesc makes netgear et eaumtendysuedbarsetetiods 81 Watermark Message siinne avi a a eos 82 M ssag Angle nmen canyon ie baecuabailetanuns a e A a es EE 82 PO THAR IOUS e e aE e Ea A iA eia nede a rE aAa E CE neds 82
90. Glossy 220g faster printing gt HP Color Laser Photo Glossy 220g high gloss gt Card Glossy 176 220g e Other Color Laser Transparency o Labels o gt Letterhead o gt Envelope o Heavy Envelope Preprinted Prepunched Colored gt Rough o Heavy Rough gt HP Tough Paper The default setting is Unspecified No mechanism exists for manually adding custom paper types through the driver Use HP Web Jetadmin to add custom paper types Custom types can be added only by using bidirectional communication so they must already exist in the product when the bidirectional query occurs If bidirectional communication is enabled then an updated list of paper types is returned If bidirectional communication is not enabled then the driver looks for custom paper types that have been saved from a previous bidirectional communication query and uses those Otherwise no custom paper types are available through the driver E NOTE To download a current version of HP Web Jetamin and for the latest list of supported host systems go to the following Web site www hp com go webjetadmin If you select a setting other than the default make sure that the correct paper type is loaded in the tray that you selected in the Paper source setting When you change the print driver setting to a paper type that is not currently loaded in the product a control panel message appears that prompts you to load the paper type or select another tray
91. Learn Center HP LaserJet Pro CM1410 Color MFP Series User Guide The HP LaserJet Pro CM1410 Color MFP Series User Guide describes the basic product features This guide may be accessed locally from the CD included with your product The latest version of this guide may be accessed from the internet To access the local version from the CD 1 In the main screen of the Installer click the More Options then click theDocumentation button 2 Click the User Guide CD button The Help and Learn Center opens 3 Click on Browse User Guide To access the latest version from the internet 1 In the main screen of the Installer click the More Options button then click the Documentation button 2 Navigate to the Manuals lt language gt folder Click the User Guide Web button The guide opens This accesses the most up to date version Chapter 1 Document and product basics ENWW HP LaserJet Pro CM1410 Color MFP Series Install Notes The HP LaserJet Pro CM1410 Color MFP Series Install Notes in HTM format contain important information about product features instructions for installing the printing system software and technical assistance To view this guide from the software CD follow these steps 1 In the main screen of the Installer click the More Options then click the Documentation button 2 Click the Readme button The guide opens You can also gain access to the file by following these steps 1 Insert the softw
92. Norwegian e Polish e Portuguese e Romanian e Russian e Slovak e Slovenian e Serbian e Spanish e Swedish e Thai o Turkish e Ukrainian e Simplified Chinese e Traditional Chinese Software availability and localization 13 14 Chapter 1 Document and product basics ENWW 2 Windows software description Introduction ENWW The product comes with software and installers for Microsoft Windows and Apple Computer Inc Macintosh systems Linux and UNIX systems are supported and software is available on the Web For information about specific system installers drivers and components see the section that corresponds to that system For information about Mac software see Macintosh software and utilities on page 111 This section contains information about the following topics e Windows printing system software e Driver configuration for Windows e HP Driver Diagnostic Printer Check Tool e HP Customer Participation Program e Scan software e HP LaserJet Fax Setup Utility e HP LaserJet Send Fax software Font support e HP Driver Deployment Utility Introduction 15 Windows printing system software This section contains information about the following topics e Windows printing system software e HP Color LaserJet print drivers Windows printing system software Table 2 1 Software components for Windows Component Description HP instal
93. OS printing system These files are used by the Macintosh OS printing system to determine default printer driver settings and to allow the user to select between the various print options and settings An HP supplied Macintosh printer configuration utility is provided which allows the user to access the HP Embedded Web Server HP EWS for additional configuration and product status monitoring The following are provided on the printing system CD e The HP LaserJet Installer for Macintosh The following components are installed by the HP LaserJet Installer for Macintosh e HP LaserJet Pro CM1410 Color MFP Series PPD e HP LaserJet Pro CM1410 Color MFP Series PDE e HP USB EWS Gateway e HP LaserJet Utility HP LaserJet Pro CM1410 Color MFP Series PPD A postscript printer description PPD file is a text file that contains keywords and other information to specify printer features options and settings PPD files are created by printer vendors for a specific postscript printer or printer family PPD files are created by printer vendors to describe the set of printer features available for their postscript printers On the Macintosh PPD files provide all the information necessary to describe a postscript printer s features including options and default settings They also contain the postscript code used to invoke those features 112 Chapter 5 Macintosh software and utilities ENWW HP LaserJet Pro CM1410 Color MFP Series PDE A Print Dialo
94. PS_14029 TTF Univers 57 Condensed Italic PS_14039 TTF Univers ExtendedPS Bold PS_13548 TTF Univers ExtendedPS Regular PS_13547 TTF Univers ExtendedPS Bold Italic PS_14481 TTF Univers ExtendedPS Italic PS_14480 TTF Font support 43 HP Driver Deployment Utility The HP Driver Deployment Utility HP DDU was created to simplify the deployment of print drivers onto a client computer It is a simple utility that packages the printer driver files and the code needed to deploy them into 2 files an EXE file and a CAB file These files are run on the client computer to copy the printer driver files to the Windows driver store and for network packages to install the product The HP DDU works with print drivers that can be installed by an INF file It is designed to work with print drivers that have their files contained in one directory structure Because this utility is generic it does not detect how specific print drivers are packaged It packages all files in the directory and subdirectories where the print driver INF file is found The print driver must be expanded so that the HP DDU can process the INF file If you download an EXE file with the printdriver files you need to run it first to unpack all of the files Then run the HP DDU to package it for deployment on the client system HP DDU can be used to pre configure a print driver for deployment When the package is run on the client computer the new configuration file is used
95. Pro CM1410 Color MFP Series product models for paper types that are not available when using the automatic duplexing unit such as cardstock and thick paper Manually printing on the second side of a page is available when you are using the HP PCL 6 driver If a duplexing unit is installed and manual duplexing is enabled in the driver the product automatically prints on both sides of paper types that are supported for automatic duplexing Letter A4 Legal and 8 5 x 11 only For paper types that are not supported for automatic duplexing a Help message 86 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW appears prompting you to configure the driver settings for manual printing on both sides Manual printing on both sides does not occur automatically Select the paper type that corresponds to the paper that you are using for the print job The following paper types have a different print modes when you manually print on the second side e Plain e Preprinted e Letterhead e Prepunched e Bond e Recycled e Colored e Rough NOTE To make the Print on Both Sides Manually check box available in the document options select the Allow Manual Duplexing option on the Device Settings tab in the printdriver Properties tab set See Installable Options on page 100 If you want to print on both sides manually while using paper that is supported for automatic duplexing you must select and apply the Not I
96. Properties and then open the Ports tab b Make sure the box is checked next to Virtual printer port for USB 5 Make sure that your computer is working correctly If necessary restart your computer The product does not print and the computer has a third party firewall installed 1 Update the firewall with the most recent update available from the manufacturer 2 If programs request firewall access when you install the product or try to print make sure you allow the programs to run 3 Temporarily turn off the firewall and then install the wireless product on the computer Enable the firewall when you have completed the wireless installation The wireless connection does not work after moving the wireless router or product Make sure that the router or product connects to the same network that your computer connects to 1 Open the Reports menu and select the Configuration Report item to print the report 2 Compare the service set identifier SSID on the configuration report to the SSID in the printer configuration for your computer 3 If the SSIDs are not the same the devices are not connecting to the same network Reconfigure the wireless setup for your product ENWW Solve wireless network problems 199 Cannot connect more computers to the wireless product 1 Make sure that the other computers are within the wireless range and that no obstacles block the signal For most networks the wireless range is within 30 m 100 ft of
97. Type fonts for printing instead of using printer fonts Advanced tab features 67 Document Options The Document Options setting contains the following controls e Advanced Printing Features e Print Optimizations Printer Features e Layout Options Advanced Printing Features When the Advanced Printing Features setting is Enabled metafile spooling is turned on and Finishing tab options such as Page Order Booklet Layout and Pages per Sheet are available depending on your product Enhanced metafile spooling is used to greatly reduce the amount of time that elapses between a request to print initiated by an application and the return of control to the application by the operating system For normal printing leave the Advanced Printing Features setting at the default Enabled If compatibility problems occur you can disable the feature However some advanced printing features might still appear in the print driver even though they have been disabled If you select an advanced printing feature in the print driver that has been disabled on the Advanced tab the feature is automatically re enabled Print Optimizations The default setting for Print Optimizations is Enabled When this feature is enabled and your document contains overlapping text and graphics the text that is placed on top of a graphic might not print correctly If the printed output is not correct you can disable this feature When this feature is disabled
98. _vistax64 hppdps08 inf 7 Click Open 8 On the Install from Disk dialog box click OK 9 Click Next Complete the installation When prompted print a test page to ensure that the printer driver is installed correctly Printer sharing disclaimer HP does not support peer to peer networking as the feature is a function of Microsoft operating systems and not of the HP printer drivers Go to Microsoft at www microsoft com Point and Print installation for Windows ENWW Use the following information to install a printer driver by using the Microsoft Point and Print feature when you do not connect directly to the product on the network Point and Print is a Microsoft term that describes a two step printer driver installation process The first step is to install a shared printer driver on a network print server The second step is to point to the print server from a network client so that the client can use the printer driver This section outlines the procedures for installing printer drivers by using Point and Print If these procedures are not successful contact Microsoft HP provides printer drivers that are compatible with the Point and Print feature but this is a function of the Windows operating systems not of HP printer drivers Administrator privileges are necessary to install the printer driver In a homogenous operating system environment one in which all of the clients and servers are running in the same operating sys
99. aaiesedeaierieas 9 Supported printer driver lanGquages c dccadsscminieenwnis arena renee 11 Installer component languages siisdciisstenynaveenevasaneensusnaiis Goarinlaieg wiaineiaka buaiie ooventalea unnen sais teatindsicsiauaeesen 12 Documentation languages sncisswonivandarvanverivxondevaruwbssrohdeniannaaawnbvndadwen saan onebbvniareiaarendvansieiasalaninn 13 Software components for WINAGWS sisjcsoissdioxdoueluoneds des chedavnaniiatanbabnneloswbihesainnsnsussanedadednitncnirlens 16 Automatic discovery and driver configuration through bidirectional communication 01ee 20 EAC availability in Microsoft Windows and Microsoft Share ccccecssseeeeereeeeeteeeseteeeeeteeeenaees 21 EAC availability in Novell Netware environments cscccesceeeenseeeneeenseeeetseteneeeneeeseeeeseeeennees 22 Operating systems that support HP Driver Preconfiguration ccccccccesseeeeeeesteceeeneeeeeestseeeeaes 25 Examples of supported e mail programs cccccssceceesceeeesnseeeesesseceseeeeeenseeeeeceseeeeensseeensaaeees 32 Ayailable scam sehingS iorenunnesinonn e E A a 33 Detdultionie mee E N e e triaianrdivarenenrcnenie 38 Additional PS emulation fonts caddy pitaive cian ansbarbin pPeetownpneennidubennds add cloucheasnaioceanstrpactunntuaneies 4 Font Attribute settings for new and preset watermarks cccccccceeesceeeeeseeeeeeseeeeeeneeeeesseeeeeens 83 PAGE orientation 4 3 2 2viensennadaventtsbnee count ina ani iene cae
100. adedianctunessteceeds ideas ChacatnsdiaecendetaQieractateres 250 Ill LATE BREAKING INFORMATION 0 cccceeceeseeeceeeeeeeeeeeeeeeeaeseaeeeeeeensaneeeeeeeaaaans 250 KNOWN ISSUES AND WORKAROUNDS cceeccceceeeeeeeestseeeeeteeeeeaes 250 General reren e E E E G ace 250 Upgrading Windows sterner snnteretiveeanicinnc es ilbaivi anindeobbintnsletano asics 250 TEC FINAL AS SES AIC Eo cccncilesanateacantions aano En E ann EEEE E EN ENERE ER EER Ei 251 CUSTOMER SUPPORT rninn N E E 251 AY EE soi nel ig bib E E da vt Pata aie udev 251 HP SOFTWARE AND SUPPORT SERVICES ADDITIONAL INFORMATION 251 V LEGAL STIATEMENIES sj cinutyasananpiecnis a a E EN 251 TRADEMARK NOTICES iepen an aa i aana ian ki e ai a ATA SEA 251 SOFTWARE WARRANTY LICENSE AND COPYRIGHT cccceeecceeeeees 251 WY GENGINTY 25s Gesuae sipacasiel tina vuinslbniiotica aeae Shedadihecanishinds 251 license srei yates marca eneagvtysteresdciagaeeen a ea 251 Copyrigh arsenic e 251 HIG OX T T T EE E A 253 xiv ENWW List of tables Table 1 1 Table 1 2 Table 1 3 Table 1 4 Table 1 5 Table 2 1 Table 2 2 Table 2 3 Table 2 4 Table 2 5 Table 2 6 Table 2 7 Table 2 8 Table 2 9 Table 4 1 Table 4 2 Table 6 1 Table 6 2 Table 6 3 Table 6 4 Table 6 5 Table 7 1 Table 7 2 Table 7 3 ENWW Documentation availability seisseen taiii E aerial e e e ah 3 Software CD supported languages iss cssacessavarcearasectvavcvosaewaneravecaserersaiacedsneceneanaieanir
101. alic CGOR46W TTF CG Times Regular CGTR45W TTF CG Times Bold CGTR65W TTF CG Times Bold Italic CGTRO66W TTF CG Times Italic CGTR46W TTF Clarendon Condensed Bold CLAR67W TTF Coronet Regular CORONET TTF CourierPS Regular CPSR45W TTF CourierPS Bold CPSR65W TTF CourierPS Bold Oblique CPSR66W TTF CourierPS Oblique CPSR46W TTF Garamond Antiqua GARR45W TIF Garamond Halbfett GARR65W TTF Garamond Kursiv GARR46W TTF Garamond Kursiv Halbfett GARR66W TTF Helvetica Regular HELR45W TTF Helvetica Bold HELR65W TTF Helvetica Bold Oblique HELR66W TTF Helvetica Narrow Regular HELR47W TTF Helvetica Narrow Bold HELR67W TTF Helvetica Narrow Bold Oblique HELR68W TTF Helvetica Narrow Oblique HELR48W TTF Helvetica Oblique HELR46W TTF ITC Avant Garde Gothic Book AVGR45W TTF ITC Avant Garde Gothic Book Oblique AVGR46W TTF ITC Avant Garde Gothic Demi Regular AVGR65W TIF ITC Avant Garde Gothic Demi Oblique AVGR66W TTF ITC Bookman Light Regular BOKR35W TTF ITC Bookman Light Italic BOKR36W TTF ITC Bookman Demi Regular BOKR75W TTF Font support 39 40 Table 2 8 Default fonts continued Font name Font style File name ITC Bookman Demi Italic BOKR76W TTF ITC Zapf Chancery Medium Italic CHANC__ TTF ITC Zapf Dingbats Regular DINGS__ TTF Letter Gothic Regular LETR45W TTF Letter Gothic Bold LETR65W TTF Letter Gothic Italic LETR46W TTF Marigold Regular MARIGOLD TTF New Century Schoolbook Bold
102. and later pages 2 If the error persists select a lower speed for may be received without error the initial transmission speed 332 337 There is a defect in the sending fax product Send from another product 338 342 ECM error 343 344 348 349 353 ECM error One of the following has occurred e The sending product has failed to respond to a fax command from the receiving product due to the connection being interrupted 1 Reattempt the fax transmission at a different time when telephone line conditions have improved 2 fax session was using error correction 354 and 355 disable ECM e The sender has touched the Cancel X button while the reception was in progress e In rare conditions incompatibility between the two products may cause the sending product to abandon the call 356 361 One of the following has occurred 1 Configure the sending product for document 362 366 ECM error e The sender has touched the Cancel X button causing the session to be aborted e The sending product has encountered a system problem such as no paper or a paper jam which has inhibited it from receiving any more pages and which has caused it to terminate the session prematurely e A feature incompatibility has been encountered by the sending product causing it to terminate the session reception by clearing any paper jams loading sufficient paper and clearing any other system errors 2 Confi
103. any large metal objects between the access point and the product Make sure poles walls or support columns containing metal or concrete do not separate the product and wireless access point e The product is located away from electronic devices that might interfere with the wireless signal Many devices can interfere with the wireless signal including motors cordless phones security system cameras other wireless networks and some Bluetooth devices e The printer driver is installed on the computer e You have selected the correct printer port e The computer and product connect to the same wireless network 198 Chapter 6 Solve problems ENWW The control panel displays the message The wireless feature on this product has been turned off 1 Touch the Wireless Menu button 2 Touch the Turn Wireless On Off button and then touch the On button The product does not print after the wireless configuration completes 1 Make sure the product is turned on and in the ready state 2 Make sure you are connecting to the correct wireless network 3 Make sure that the wireless network is working correctly a Open the Network Setup menu and then open the Wireless Menu item b Select the Run Network Test item to test the wireless network The product prints a report with the results 4 Make sure that the correct port or product is selected a From the list of printers on your computer right click the name of this product click
104. aper sizes Letter This setting changes according to country region e Paper type Unspecified e Print on both sides No e Color Options Color Envelopes e Paper source Automatically Select e Paper sizes Envelope 10 e Paper type Envelope Cardstock Heavy e Paper source Automatically Select e Paper sizes Letter This setting changes according to country region e Paper type HP Cover Matte 200g 106 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW Print on both sides No Color options Color Glossy Presentation Paper source Automatically Select Paper sizes Letter This setting changes according to country region Paper type Unspecified Print on both sides No Color theme Default sRGB Snapshot Photos Labels Labels Paper source Automatically Select Paper sizes 4x6 Paper type HP Color Laser Photo Glossy 220g faster printing Color theme Photo Paper source Automatically Select Paper sizes Letter Paper type Labels this option is grayed out so it cannot be changed Color options Color Paper source Automatically Select Paper sizes Letter Paper type Transparency this option is grayed out so it cannot be changed Color options Color Create a custom printing shortcut 1 2 ENWW Select General Everyday Printing as a base Select the appropriate print settings on the Printing Shortcuts tab or use the settings on any of the Printing P
105. are CD into the CD ROM drive 2 Navigate to the CD Setup Docs Readme folder 3 Open the file that has the appropriate file name IJCM1410_install notes_XXWW HTM amp NOTE The XXWW in the file name corresponds to the language For instance the file name for the French version of the document is IICM1410_install notes_ FRVWWW HTM Help and Learn Center Click Help and Learn Center on the Documentation screen of the Installer to connect to a Web page that provides step by step instructions for performing specific tasks including clearing jams and loading trays Administrator documentation The following figure shows the Administrator Documentation screen To navigate to this screen click the More Options button on the main screen of the Installer and then click the Admin Documentation button E NOTE These links are to non product specific documentation that may be useful and is available only online Internet access is required ENWW Documentation availability and localization 6 Figure 1 2 Installation software CD Administrator Documentation screen Ap HP LaserJet Professional CM1410 Series Software Install aS HP Driver Configuration Utility User Guide Online The Driver Configuration Utility enables system administrators to customize print driver settings before deploying the drivers to a client or server More Options Documentation A gt HP Jetdirect Guide Online View the HP Jetdirect Adminis
106. are availability and localization 7 The Utilities folder contains the files to run these stand alone utilities e FileToEmail e Scrubber 8 Chapter 1 Document and product basics ENWW CD versions and language support The product printing system software CD is available with the following components and languages Table 1 2 Software CD supported languages Language Two letter abbreviation HP preferred name File designation Arabic AR Arabic ARWW Bahasa Indonesian ID Bahasa Indonesian IDWW Bulgarian BG Bulgarian BGWW Catalan CA Catalan CAWW Croatian HR Hrvatski HRWW Czech CS Cestina CSWW Danish DA Dansk DAWW Dutch NL Nederlands NLWW English EN English ENWW Estonian ET Eesti ETWW Finnish Fl Suomi FIWW French FR Francais FRWW German DE Deutsch DEWW Greek EL Greek ELWW Hebrew HE Hebrew HEWW Hungarian HU Magyar HUWW Italian IT Italiano ITWW Japanese JA Japanese JAWW Kazakh KK Kazakh KKWW Korean KO Korean KOWW Latvian LV Latviski LVWW Lithuanian LT Lietuviskai LTWW Norwegian NO Norsk NOWW Polish PL Polski PLWW Portuguese PT Portugues PTWW Romanian RO Romanian ROWW Russian RU Russian RUWW Serbian SR Srpski SRWW Simplified Chinese ZHCN Simplified Chinese ZHCN ENWW Software availability and localization Table 1 2 Software CD supported languages continued Language Two letter abbreviation HP preferred name File designation Slovak SK Slovak
107. are files reside on the Macintosh disk The HP LaserJet Installer for Macintosh is at the root of the Macintosh CD The user manuals PDF are grouped by language and are in the Documentation directory on the Macintosh partition of the software CDs ENWW Macintosh printing system software 115 Macintosh install and uninstall instructions e Install the Macintosh printing system software e Remove the printing system software from Macintosh operating systems Install the Macintosh printing system software On a Macintosh computer the printing system software installation procedures are the same for a network administrator a network client or a single user Install the printing system software on any computer that has access rights to the product The computer user must also have administrative rights on the computer to install the printing system software e General installation for Macintosh operating systems e Setup instructions General installation for Macintosh operating systems 1 If you are connecting the product to a network connect the network cable to the network port If you are connecting the product to a computer by using the USB cable connect the USB cable 2 Insert the Macintosh printing system software CD into the CD ROM drive amp NOTE If the HP LaserJet installer browser screen does not open automatically when the CD is inserted into the CD ROM drive double click the product CD image on the de
108. artridge that has the words HP or Hewlett Packard on it or has the HP logo on it Genuine HP print cartridge 1 The product control panel or the Supplies Status page indicates Very Low status when the cartridge has reached the end of its estimated life Replace the print cartridge if print quality is no longer acceptable 2 Print a Print Quality Page from the Reports menu on the control panel If streaks or marks are in one color on the page you might have a defect in that color cartridge See the instructions in this document for interpreting the page Replace the print cartridge if necessary 3 Visually inspect the print cartridge for damage See the instructions that follow Replace the print cartridge if necessary 4 If printed pages have marks that repeat several times at the same distance apart print a cleaning page If this does not solve the problem use the repetitive defects ruler in this document to identify the cause of the problem ENWW Improve print quality 183 Print the Supplies Status page The Supplies Status page indicates the estimated life remaining in print cartridges It also lists the part number for the correct genuine HP print cartridge for your product so you can order a replacement print cartridge as well as other useful information 1 On the product control panel open the Reports menu 2 Select the Supplies Status page to print it 184 Chapter 6 Solve problems ENWW In
109. as 217 Print alll Mere DOTS menr aeoea e E E eden erued aunt nereneane 217 Print individual fax reports cic asteccstvednas oosucdirsvomvenatioctedinas bay tierra uhuadvasnacneeaah 219 Set the fax rror report sistre sassi oei e ennan sila NT iet 219 Change error correction and fax speed 4 u5 divider nniieni deen enw ana 219 Set the fax error correction mode visetiesuasines hecerodiondondecmuiieeuncimavnees 219 Change the fax speeds mcssesccsiassrecenalheneendd taaavadeie dessa cuauaiaseensare ON 220 Solve problems sending faxes gyn uey eons ways speecen aus Aan eed ence oan ewe 220 An error message displays on the control panel cceeesseseeeeeeeeeetteeees 220 The Communication error Message Appears eeeeeeeeeeeeeeeeeees 220 Nodial ton zseni tite tae east ieee ante ah Wee Scie 221 The Fax is busy message appeors lt aeesscvsx asacesnagaconmedaresansraaeont 221 The No fax answer message appears ccceeceeeeeeeseeeeeeeteeeeeees 222 Document feeder paper jam cccccccceeeesseeeeeeteeeeeeeteeeeeeseeeeees 222 The Fax storage is full message appears cceeeeeeeeeeeeeeceeeeees 223 Scanner error orech ien eE EE alent ees 223 The control panel displays a Ready message with no attempt to send the fax 223 The control panel displays the message Storing page 1 and does not progress beyond that message cccccceeeeeeseeecceseeenceeeeeeseeeeeeeeseeetaeeees 224 Faxes can be received but n
110. ath For example type the following put C LJ P3010FW PDF E NOTE If the file name or path includes a space you must enclose the file name or path in quotation marks For example type put c My Documents LJ P3010FW PDF The following series of messages appears in the command window 200 PORT command successful 150 Opening BINARY mode data connection 226 Ready 226 Processing Job 10 Press Enter on the keyboard 11 The print ready file prints 12 At the command prompt type bye to exit the FTP command 13 At the command prompt type exit to return to the Windows interface ENWW Printing printready documents 239 Macintosh operating systems 1 9 Make note of the TCP IP address on the Embedded Jetdirect page The HP Embedded Jetdirect page is the second page of the configuration page printout Open a Terminal window on your Macintosh You can find the Terminal program on the computer in the following location System Applications Utilities Terminal Open the Finder select Applications and then click Utilities Double click to open the Terminal utility Type FTP lt TCP IP product ADDRESS gt For example if the TCP IP address is 192 168 0 90 type the following FTP 192 168 0 90 Press Enter on the keyboard When prompted for a user name and password press Enter You can drag and drop the firmware file into the Terminal folder System Applications Utilities Terminal Alternatively you can type put lt
111. ation Use the Device Settings tab to tell the driver about the hardware configuration of the product If bidirectional communication is enabled in a supported environment update this tab by selecting the Update Now setting in the Automatic Configuration setting The default setting is Off After an automatic configuration the setting returns to Off after the changes are made If your environment does not support bidirectional communication the Update Now setting is unavailable so you must manually configure the options on this tab If you have more than one driver installed for the product for example the default HP PCL 6 Print Driver and the HP PCL 5 Universal Print Driver the Update Now feature works automatically only on the driver on which it is activated The other driver will not be updated and might show the default setting for the specific product model Allow Manual Duplexing Select Allow Manual Duplexing to print on both sides of any supported size and most types of paper except transparencies envelopes and labels To use this feature you must reinsert the paper stack into the input tray to print the second side The product pauses while you make this adjustment This setting is enabled by default Job Separator ENWW Use this control to specify whether a print job identifier page should be printed between print jobs Device Settings tab features 101 Printing Shortcuts tab features e Use defined printing s
112. ation for instance you can select the paper input tray from any of them settings that are established in the software program take precedence over print driver settings Print driver settings in turn override product control panel settings When you install the printing system software in Windows the HP PCL 6 Print Driver is installed by default through the installer The HP PS Universal Print Driver and the HP PCL 5 Universal Print Driver can be installed by downloading the software from the Web Topics e Access print drivers e Help system e Advanced tab features e Paper Quality tab features e Effects tab features e Finishing tab features e Color tab features e Services tab features e Device Settings tab features Introduction 6l e Printing Shortcuts tab features e About tab features Access print drivers Depending on the operating system on which you are installing the print drivers you can gain access to the print drivers and different print driver interfaces in several ways To gain access to the print driver settings from within most software programs follow these steps 1 Click File 2 Click Print 3 Click Properties The appearance and names of the driver tabs can vary depending on the operating system These driver settings apply only while that software program is open You can control the drivers directly from the Printers folder Here you have access to two s
113. atures such as the fax phone book However you can still preview and send faxes In some cases faxing from the computer is more convenient and offers more choices than faxing from the product control panel such as in the following e Fax to multiple recipients e Create a cover page e Fax pages scanned from the product document feeder e Fax without first printing and scanning the document For any fax job click Preview to view the fax and click Send Now to send the fax NOTE For more information about faxing see the HP LaserJet CM1410 MFP Series User Guide which is available on the printing system installation CD that came with the product 36 Chapter 2 Windows software description ENWW Fax to multiple recipients To send a fax to multiple recipients use the HP LaserJet Send Fax software to create a recipient list by using one of the following methods e Click Create Recipient List on the HP LaserJet Send Fax dialog box For each recipient type in the information and then click Add to list e If you have stored entries in the fax phone book in HP ToolboxFX click Phone Book on the HP LaserJet Send Fax dialog box click Create Recipient List and then drag and drop recipient names from the Phone Book field to the Recipient List field To add new entries to the fax phone book in HP ToolboxFXx click Edit to open HP ToolboxFX NOTE If you add new entries in HP ToolboxFX click Refresh on the HP LaserJet Send
114. available when you touch the Scan button on the product control panel E NOTE Photos are scanned at 150 dpi and documents are scanned at 300 dpi From the computer by using HP Scan Windows Click Start select Programs or All Programs select HP select the name of the product and then click Sean For more information see HP Scan software on page 29 From a WIA or TWAIN compliant software program Check the help system in the software program to learn how to scan by using a WIA or TWAIN compliant scanner from within that program For more information see Scan drivers on page 33 28 Chapter 2 Windows software description ENWW HP Scan software Use the HP Scan software to scan from the product and then complete any of the following tasks with the data e Save the scanned item to a file e Attach the scanned item to an e mail e Perform text recognition on the scanned item through Readiris if Readiris text recognition software is installed on the computer e Open the scanned item with any third party software program that supports the drag and drop function To use the HP Scan software click Start select Programs or All Programs select HP select the name of the product and then click Sean The HP Scan software saves the scan as any of the following image file types e BMP e GIF e JPG e PDF e TIFF both regular and compressed Convert a scanned document into editable text by using the Readiris
115. ble settings to change the TrueType to printer font mapping and to install and remove external fonts for the product through the External Fonts option External fonts can be soft fonts or DIMM fonts Click the Font Substitution Table option to open a list of fonts as show in the following figure Use the settings to change the TrueType to product font mappings External Fonts Use the External Fonts option to install and remove external fonts for the product External fonts can be soft fonts or DIMM fonts Click the External Fonts option to make the Properties button available Click Properties to open the HP Font Installer dialog box which is shown in the following figure ENWW Device Settings tab features 99 Installing external fonts Follow these steps to install external fonts 1 9 MOM PE ee ee ON In Windows Vista and Windows 7 click the Start button click Control Panel click Hardware and Sound and then click Printers In Windows XP Windows Server 2003 and Windows Server 2008 click Start click Settings and then click Printers and Faxes Right click the name of the product Click Properties Click the Device Settings tab Click the External Fonts option The Properties button appears Click Properties The HP Font Installer dialog box appears Type the name and path of the font metric file in the Printer Font File Location text box or click Browse to locate the file on the computer The font file names ap
116. button to return to the main menus 4 Open the 2ndary Service menu 5 Open the Button test menu Engine Diagnostics Engine test 1 With the product off open the front and rear doors 2 Turn the power on and close both doors within ten seconds 3 An engine test page a page containing multiple horizontal colored lines will print 124 Chapter 6 Solve problems ENWW Use the HP ToolboxFX software HP ToolboxFX is a program that you can use to complete the following tasks Check the product status Configure the product settings View troubleshooting information You can view HP ToolboxFX when the product is directly connected to your computer or is connected to the network You must perform a recommended software installation to use HP ToolboxFX amp NOTE HP ToolboxFX is not supported for Windows 2000 Windows Server 2003 Windows XP 64 bit or Macintosh operating systems To use HP ToolboxFX you must have TCP IP protocol installed on your computer You do not have to have Internet access to open and use HP ToolboxFX View the HP ToolboxFX Status ENWW Open HP ToolboxFX in one of these ways In the Windows system tray double click the HP ToolboxFX icon 8 On the Windows Start menu click Programs or All Programs in Windows XP and Vista click HP click the name of this product and then click HP ToolboxFX The Status folder contains links to the following main pages Device status This page indica
117. call Stamp Faxes On Sets the product to print the date time sender s phone number and page number on each page of incoming Off faxes Private Receive On Setting Private Receive to On requires you to set a product password After setting the password the following off options are set e Private Receive is turned on e All old faxes are deleted from memory e Fax forwarding is set to Off and is not allowed to be changed e All incoming faxes are stored in memory Confirm Fax On Confirm a fax number by entering it a second time Number Off Allow Fax Reprint On Sets whether incoming faxes are stored in memory for reprinting later Off Fax Tel Ring Time 20 Sets the time in seconds after which the product should stop sounding the Fax Tel audible ring to notify the user of 30 an incoming voice call 40 70 Fax Speed Fast V 34 Sets the allowed fax communication speed Medium V 17 Slow V 29 138 Chapter 6 Solve problems ENWW System Setup menu In the following table items that have an asterisk indicate the factory default setting Menu item Sub menu item List of available control panel display languages Language Sub menu item Description Sets the language in which the control panel displays messages and product reports Paper Setup Default Paper Size Default Paper Type Tray 1 Letter A4 Legal Lists available paper types Paper Type Paper Size Sets the size for printing inter
118. cdaaavonnsobneahediesaubiadawesatindibadedscimedeobunbdacs 16 HP Color LaserJet print drivers sucess incesncconceonesoncy eratneytaiadynccatenilulakdgananenanneeinarancnven 18 HP PCL 6 Print Driver PCL 5 Universal Print Driver and PS Universal Print AVS i suspens aniano tenon a e ea a E a tees 18 Print driver version numbers for Windows operating systems cccceeceee 18 Driver configuration for Windows saicctincysierdinnnipiiinbioninayniisubanpuubshdacenddviceda uaubdialedardadibuaaedaindaida 20 Driver autoconfiguration 5 asec cetera cacssenssdiacheihewers ataeceasadntera lt autavetacauenityd var ea vaaranenaeinne 20 Bidirectional communication 225 xnssd tse acmnalandlasiae inci sb tass dhsadindansatgenas tenes tench tnaaceondsdaAtddaten 20 Enterprise AutoConfiguration scciicynsnhstvss vetessesatietevsaileiaeishbaiofeillanedi ene ndlbe bedatian dncede nthyitadise 20 Update hpricot E AE E E 22 HP Driver Configuration siisii in E E AE A E EA 23 Lockable features nnnnnsnessseesseesseesseessserssttsssersstsstrsstesssersseesssersessrersste 25 Continuous SX POM a5 14 5c sstacens iamessneeedsecad se wguaapancecsaentaeassuerntseneeparmeaetaneaee 25 HP Driver Diagnostic Printer Check Tool sa cratacsonguseanetuieet tne va duronwaguawiersaniundncaieeinanan etrasaion age nenanntaold 26 HP Customer Participation Program cceeceecceccceeeeeeeeeeeeceeeeeceeeeeeeeeaaaecaaaeeeeseeeeeeeeeeeeeeeneaeeaaea 27 ENWW iii Scan ME OAS oeer eena e
119. ces and destinations e Source commands e Media types Media sources and destinations The following table shows the standard and optional media sources and destinations for the product Table 7 1 HP LaserJet Pro CM1410 Color MFP Series MFP Series media sources and destinations Media sources Priority input tray standard Tray 1 standard Document feeder input bin standard Media destinations Output bin standard Document feeder output bin standard Source commands The PCL 6 attribute for paper source is ubyte MediaSource or ubyte_array string MediaSource See the following table for values of For example ubyte 4 MediaSource is the command for Tray 2 The PCL 5 escape sequence for media source is Esc amp l H the I is a lowercase L rather than the numeral 1 See the following table for values of For example Esc amp 11H is the command for Tray 2 Table 7 2 Media source commands Media source PCL 6 PCL 5 UPD PostScript ubyte MediaSource or Esc amp 1 H MediaPosition ubyte_array string ManualFeed true false or MediaSource null Tray 1 3 4 3 false Auto Select 1 7 NA Manual feed in tray 1 2 2 3 true For the string value you must use inc ude the quotation marks around the variable For example ubyte_array TRAY2 MediaSource is the PCL 6 command for Tray 2 ENWW Paper and print media 243 Media types Media type commands The PCL 5 escape sequence for paper type is E
120. cipating in HP s voluntary program for communication between your system and HP This feature available through software that is included on the printing system software installation CD helps HP monitor toner usage At the time of the invitation about two weeks after installation full disclosure of the information to be communicated is provided Participation is entirely voluntary and the impact on processing and connection speeds is negligible Personal information is never sent to HP unless permission is given Figure 2 1 Welcome to the HP Product Survey Program screen HP LaserJet CM1410 Series PCL 6 1 Welcome We invite you to join our HP Product Improvement Study to help improve the quality reliability and performance of HP printers If you accept we ll collect information about your HP printer and any future installations of the same printer model to identify usage trends and patterns If at anytime you wish to stop sharing information with HP select HP Product Improvement Study under the HP tab in your start menu We will not collect your name address or any other personal information except serial number No content or file names from any of your printed pages is collected or stored by HP There are only a few questions to answer and you can continue working without interruption This is completely voluntary HP Privacy Statement Online Participate Remind me later If you decline the invitation the dialog box d
121. ck the product icon 3 Click Properties The following Properties print driver tabs are available e General e Sharing e Ports e Advanced e Color Management e Security e Device Settings e About ENWW Access print drivers 63 Help system The HP PCL 6 Print Driver includes a full featured Help system to provide assistance with printing and configuration options What s this Help Windows XP Windows Server 2003 Windows Server 2008 Windows Vista and Windows 7 support What s this Help You can gain access to What s this Help messages in any of the following ways e Right click a feature or control A pop up Help window appears e Click the button in the upper right corner of the frame next to the X to change the cursor to an arrow with a question mark When you use this special cursor to select a control the pop up Help window for that feature appears e Click a feature or control and then press the F1 key The Help window for the currently selected control appears Incompatible Print Settings messages 64 Incompatible Print Settings constraint messages are unsolicited messages that appear in response to specific printdriver selections These messages alert you to selections that are illogical or impossible given the product capabilities or the current settings of other controls NOTE Constraint messages are limited and the underlying software architecture might accept some settings that are i
122. color i042 aon la eek eee Reon 165 Scanner error Turn off then on cseesccneesccccuscceeueeseeueesess 165 Scanner reserved for PC scan secceeeseeeenseeeseseecenseeeseeeeeeneeees 166 Scanning error Cannot connect ccseeeeseeeeeeeeeeeeeeeeeeeeeeeeaeeees 166 SEMIS cleared henik a a A ee IE 166 Used color installed to accept press OK ccccceeeeeeeeeeeeeneee 166 Yellow Cartridge Low nsas 2 trustee tunuaanctnuued ccna eiasiaes 166 Yellow in wrong position acces escnaspamcaunonavereuerecnimaeinncoenns 167 Yellow Very LOW re ciii e i 167 Event log messages sc civiriscsrsmontersiauvesrsnidasdounnousdiuewles ebesknnl ebygGaurigniateysnnrebestnuehiers 168 MON URING ifs seeded teteta actavaceaty cond uadavaadiits cagea vege coe pie aaa a ea aea Gea oa 170 Paper feeds incorrectly or becomes jammed ccccccceceesceeeeenseeeeeseeeeeeeeeeeseseeeceeeeesseeeeseeaes 171 The product does not pick up papers ciacsncenpexnarcadeusacer votio ean taeirdaree Sacareenenaorsaens 171 The product picks up multiple sheets of paper cccccceeeescecceseeeeeeeeneeeeeeteesentseees 171 PreVEnt paper YAMS mesici oruinn inneas i E e N a a E E eee 171 Gleam JMS e etke e a E E neat E e ES A emit 172 Jam locations deepen ee e EET A E A 172 Clear jams from the document feeder ccccceceeesececeseeeneeeeeseteeeeenaes 173 Clear jams from the input tray c cicshensceotse tuned akeitaiedesvantusetoned auacnendee
123. color This item adjusts density settings for contrast highlights midtones and shadows Adjust each color individually Timing This item specifies how frequently the product should automatically perform a color calibration The default setting is 48 hours You can turn automatic calibration off PBX ring detect On or Off Configure the PBX ring detect setting Clean Belt This item runs additional belt cleaning cycles Pick roller This item puts the pickup roller in position for replacement Product resets The product resets Restore Defaults and the NVRAM initialization perform the same function If possible use the Restore Defaults function in the Service menu If that menu is not accessible use the NVRAM sequence Restore the factory set defaults A CAUTION Restoring the factory set defaults returns all of the product and network settings to the factory defaults and it also clears the fax header name phone number and any stored faxes in the product memory This procedure also clears the fax phone book and deletes any pages that are stored in the memory The procedure then automatically restarts the product 1 On the product control panel touch the Setup button 2 Scroll to and touch the Service menu 3 Scroll to and touch the Restore Defaults button and then touch the OK button ENWW Service mode functions 203 The product automatically restarts NVRAM initialization Performing an NVRAM in
124. constraint messages print drivers 64 continuous export 25 contrast print density 130 control panel button test 203 clean touch screen 192 cleaning page printing 190 display test 203 HP ToolboxFX system settings 13 menus 133 message types 151 messages troubleshooting 151 settings 113 copy menu 145 copying quality adjusting 189 cover page fax 37 covers settings 75 Index 253 custom paper types adding 74 D data store parameters 244 DDU see HP Driver Deployment Utility 24 44 defaults NVRAM initialization 204 defaults restoring 203 defects repetitive 187 Enterprise AutoConfiguration 20 HP Driver Configuration Utility User Guide 6 HP Driver Preconfiguration support 25 included 18 languages 11 lockable features 25 media source commands 243 network configuration 23 Pointand Print installation 59 error codes 206 error report printing 219 error correction 219 factory set defaults restoring 203 HP LaserJet HP Send Fax software 36 multiple recipients sending to 37 receive log 128 receiving troubleshooting 206 reports 146 density settings 130 scan 17 device polling 131 Device Status screen reports printing all 217 Update Now bidirectional ring type 137 communication 101 send log 128 EWS 97 duplexing sending troubleshooting 210 diagnostics supported products 106 Setup Utility screen 35 troubleshoot 96 solve general problems 233 direct printing E unable to receive 227 FTP
125. cratches fingerprints or other damage on the imaging drum replace the print cartridge 5 If the imaging drum does not appear to be damaged rock the print cartridge gently several times and reinstall it Print a few pages to see if the problem has resolved 186 Chapter 6 Solve problems ENWW Repetitive image defects If the product output has a consistent repetitive defect then use the table in this section to determine which part needs to be replaced based on the measured distance between the repetitions of the defect amp NOTE The following table replaces the graphical repetitive defect ruler You can make your own ENWW ruler by using these measurements For the most accurate results use a metric ruler Table 6 2 Repetitive image defects Distance between Component Notes identical defects 22 3 mm 0 87 in Developer roller one rotation Appears in a single color plane 26 7 mm 1 05 in Charger roller Appears in a single color plane 28 5 mm 1 12 in Developer RS roller one rotation Inside developer this roller removes and supplies toner to the developer sleeve 44 0 mm 1 73 in Registration roller 56 5 mm 2 22 in Fuser film one rotation Appears in all color planes 56 8 mm 2 23 in Fuser pressure roller one Appears in all color planes rotation 57 0 mm 2 24 in Transfer roller Appears in all color planes 69 0 mm 2 71 in Cartridge to cartridge spacing Distance between each color i
126. d product attempt the transmission using the V 17 mode Solve fax problems 215 216 Table 6 5 Fax send error codes continued Error code Description Solution 396 409 An error occurred during a V 34 transmission handshake with the sending product and was consequently unable to transmit a T30 frame This occurs when the line was disconnected or if line conditions degrade during the session 410 419 An error occurred during a V 34 reception when the receiving product was unable to correctly handshake with the sending product and was consequently unable to transmit a T30 frame This occurs when the line is disconnected or if line conditions degrade during the session 420 V 34 negotiations have failed from the originating product during phase four which occurs after V 8 and before the first T 30 frames are exchanged Compatibility problems have been observed in this area when sending to non HP units 421 V 34 negotiations have failed from the originating product during phase three which occurs after V 8 before phase four and before the first T 30 frames are exchanged Compatibility problems have been observed in this area when sending to non HP units 422 V 34 negotiations have failed from the answering product during phase four which occurs after V 8 and before the first T 30 frames are exchanged 423 430 V 34 negotiations have failed from the answering product d
127. d You can toggle between portrait and landscape page orientation by clicking the image Print Quality The Print Quality group box contains the following controls Print Quality drop down menu 76 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW Print Quality drop down menu ENWW Use this control to select print quality ImageREt settings precisely control colors by combining up to 4 colors and varying the amount of toner in a given area to create many smooth colors sharp images and crisp text The Print Quality drop down menu contains the following resolution options e ImageREt 3600 This setting is selected by default e 1200 x 1200 This setting may improve the rendering of fine lines and text Paper Quality tab features 77 Effects tab features NOTE The Effects tab is located on the Printing Preferences tab set For information about how to access these tabs see Printing Preferences driver tabs on page 62 Use the Effects tab to create unique paper effects such as scaling and watermarks The following figure shows the Effects tab Figure 4 4 Effects tab amp HP LaserJet M1410 Series PCL 6 Copy 1 Printing Preferences Advanced Printing Shortcuts Paper Quality Effects Finishing Color Services Resizing Options O Actual size Print document on Letter Scale to fit Z of actual size Watermarks none First
128. d then type cmd b Type ping followed by the IP address for your product c If the window displays round trip times the network is working 2 If the ping command failed verify that the network hubs are on and then verify that the network settings the product and the computer are all configured for the same network The product is using incorrect link and duplex settings for the network Hewlett Packard recommends leaving this setting in automatic mode the default setting If you change these settings you must also change them for your network New software programs might be causing compatibility problems Verify that any new software programs are correctly installed and that they use the correct printer driver The computer or workstation might be set up incorrectly 1 Check the network drivers printer drivers and the network redirection 2 Verify that the operating system is configured correctly The product is disabled or other network settings are incorrect 1 Review the configuration page to check the status of the network protocol Enable it if necessary 2 Reconfigure the network settings if necessary ENWW Solve connectivity problems 197 Solve wireless network problems NOTE Wireless models only e Wireless connectivity checklist e The control panel displays the message The wireless feature on this product has been turned off e The product does not print after the wireless configuration comp
129. ding Typically the sender should ensure paper is loaded product is not able to receive a document This in the product paper jams are fixed and any error should be very rare since normally a sending other system abnormalities are cleared product will not answer if it cannot receive a document On of the few exceptions to this would occur if the sending product was configured to poll transmit a document but was unable to receive 317 The sending product cannot support a fax N A reception at any speed or modulation that is supported by the receiving product 318 The sending product cannot support a fax N A reception at the page width selected by the receiving product 319 The receiving product has attempted to initiate a Do one of the following binary file transfer BFT but has detected that the sending product does not support this mode of e Enable the BFT capability on the sending operation product if it is supported e Retransmit the document as a normal fax rather than attempting a BFT transfer 320 The receiving product is set up to initiate poll Do one of the following reception with a sending product but it has detected that the sending product is not configured Confirm that the receiver really wants to to do this Poll transmission from a sending product attempt a poll reception If not reconfigure is typically configured on a session by session the receiving product for a normal fax basis transmission e Configure the sendin
130. document feeder tray and start over Communication error Description A fax communication error occurred between the product and the sender or receiver Recommended action Allow the product to retry sending the fax Unplug the product telephone cord from the wall plug in a telephone and try making a call Plug the product phone cord into a jack for another phone line Try a different phone cord Set the Fax Speed option to the Slow V 29 setting or disable the Fasi V 34 setting Turn off the Error Correction feature to prevent automatic error correction E NOTE Turning off the Error Correction feature can reduce image quality Print the Fax Activity Log report from the control panel to determine if the error occurs with a specific fax number Cyan Cartridge Low Description The print cartridge is nearing the end of its useful life Recommended action Printing can continue but consider having a replacement supply on hand Cyan in wrong position ENWW Description The print cartridge is installed in the incorrect slot Recommended action Make sure that each print cartridge is installed in the correct slot From front to back the print cartridges are installed in this order black cyan magenta and yellow Tools for troubleshooting 155 Cyan Very Low Description The print cartridge is at the end of its useful life and the At Very Low menu item in the System Setup menu is set to Continue Recommended act
131. drive and then navigate to the Driver Deployment Utility folder For more information about the HP DDU refer to HP Driver Deployment Utility on page 44 For detailed information about gaining access to and installing these tools see the HP Driver Configuration Support Guide at the following Web site and click on the Manuals link www hp com go dcu 24 Chapter 2 Windows software description ENWW Lockable features The following driver features can be locked to prevent end users from changing settings e Print on Both Sides duplex The options are True or False e Print in Grayscale The options are Disable or Enabled e Media Type The options include all the paper types that the HP LaserJet Pro CM1410 Color MFP Series product supports e Paper Source The options are Printer Auto Select Manual Feed Tray 1 Tray 1 e Job retention mode The option is Off e Orientation e Color Options When a feature is locked the selected default option is the only option that is available to users Generally the feature is unavailable in the driver UI after it has been locked Continuous export ENWW The term continuous export refers to the ability of the print driver to copy the latest printdriver settings back to the working copy of the preconfiguration file Using this feature the exported values can be transferred when a compatible version of the print driver is used to upgrade the print driver For instance if the orientation
132. e and productsupport information go to www hp com support CM 141 Oseries The Windows XP Windows Server 2003 Windows Server 2008 Windows Vista and Windows 7 operating systems support the HP PCL 6 PCL 5 Universal Print Driver and PS Emulation Universal Print Chapter 2 Windows software description ENWW Drivers If you are using an HP print driver in a Windows environment follow these steps to find driver version information 1 In Windows Vista and Windows 7 click the Start button click Control Panel click Hardware and Sound and then click Printers In Windows XP Windows Server 2003 and Windows Server 2008 click Start click Settings and then click Printers and Faxes 2 Rightclick the product icon 3 Click Properties 4 Click the About tab You can also gain information about driver versions by clicking the About button that appears on most driver tabs ENWW Windows printing system software 19 Driver configuration for Windows The HP print drivers feature bidirectional communication technology which in supported environments provide automatic discovery and driver configuration for product accessories at the time of installation Some accessories that are automatically discovered and configured include the duplexing unit optional paper trays printer hard disk and dual inline memory modules DIMMs Driver autoconfiguration Automatic discovery and driver configuration through bidirectional communica
133. e Booklet Printing drop down menu is Off The other settings have the following format where paper size depends on the paper size that is set on the Paper Quality tab e Left Binding e Right Binding When you select Left Binding or Right Binding the document preview image changes to show the location of the binding If the Pages per Sheet setting is on the default setting of 1 it automatically changes to 2 pages per sheet If you change the Pages per Sheet setting manually to 4 6 9 or 16 pages per sheet the booklet setting is disabled See Pages per Sheet on page 90 for more information Book and Booklet Printing The HP LaserJet Pro CM1410 Color MFP Series supports book and booklet printing A book is a print job consisting of at least two pages It can have a different paper type for the front cover first page other pages last page or back cover Use the Covers and Print pages on different paper settings on the Paper Quality tab to select different paper for the front cover first page other pages and back cover For more information see Paper Quality tab features on page 70 A booklet is a print job that places two pages on each side of a sheet that can then be folded into a booklet that is half the size of the paper Use the Booklet Layout drop down menu on the Finishing tab to control booklet settings Print a booklet 1 Open the driver Printing Preferences tab set and click the Printing Shortcuts tab For informati
134. e button Load plain letter or A4 paper when you are prompted Touch the OK button to begin the cleaning process A page feeds through the product slowly Discard the page when the process is completed Paper feeds incorrectly or becomes jammed 177 Clear jams from the output bin A CAUTION Do not use sharp objects such as tweezers or needle nose pliers to remove jams Damage caused by sharp objects will not be covered by the warranty 1 With both hands grasp the paper and carefully pull it free from the product 178 Chapter 6 Solve problems ENWW Improve print quality You can prevent most print quality problems by following these guidelines Use the correct paper type setting in the printer driver Adjust color settings in the printer driver Use paper that meets HP specifications Print a cleaning page Calibrate the product to align the colors Check the print cartridges Use the printer driver that best meets your printing needs Improve print quality for copies Use the correct paper type setting in the printer driver Check the paper type setting if you are having any of the following problems Toner is smearing on the printed pages Repeated marks occur on the printed pages Printed pages are curled Toner flakes off the printed pages Printed pages have small unprinted areas Change the paper type setting for Windows 1 a i Oo O N On the File menu in the
135. e file that you want to print is not listed in the USB Flash Drive menu The USB Flash Drive menu does not open when you insert the USB accessory 1 You might be using a USB storage accessory or a file system that this product does not support Save the files on a standard USB storage accessory that uses File Allocation Table FAT file systems The product supports FAT12 FAT16 and FAT32 USB storage accessories 2 If another menu is already open close that menu and then reinsert the USB storage accessory 3 The USB storage accessory might have multiple partitions Some USB storage accessory manufacturers install software on the accessory that creates partitions similar to a CD Reformat the USB storage accessory to remove the partitions or use a different USB storage accessory 4 The USB storage accessory might require more power than the product can provide a Remove the USB storage accessory b Turn the product off and then on c Use a USB storage accessory that has its own power supply or that requires less power 5 The USB storage accessory might not be functioning correctly a Remove the USB storage accessory b Turn the product off and then on c Try printing from another USB storage accessory The file does not print from the USB storage accessory 1 Make sure paper is in the tray 2 Check the control panel for messages If paper is jammed in the product clear the jam The file that you want to print is not
136. e to load the same settings onto another product or to restore these settings to this product at a later time e Product Security Set change or clear the product security password Device Information The Device Information page stores data about your product for future reference The information that you type in the fields on this page appears on the Configuration page You can type any character in each of these fields NOTE You must click Apply before your changes take effect ENWW Tools for troubleshooting 129 Paper Setup Use these options to configure your default settings The following options are available for handling print jobs when the product is out of paper e Select Wait for paper to be loaded e Select Cancel from the Paper out action drop down list to cancel the print job The Paper out time field specifies how long the product waits before acting on your selections You can specify from 0 to 3600 seconds NOTE You must click Apply before your changes take effect Print Quality Use these options to improve the appearance of your print jobs Color Calibration e Power On Calibration Specify whether the product should calibrate when you turn it on e Calibration Timing Specify how frequently the product should calibrate e Calibrate Now Set the product to calibrate immediately NOTE You must click Apply before your changes take effect Print Density Use these settings to make fine ad
137. ear jams from the document feeder 1 Turn the product off 2 Open the document feeder cover ENWW Paper feeds incorrectly or becomes jammed 173 3 Lift the document feeder mechanism and gently pull the jammed paper out 4 Close the document feeder cover 174 Chapter 6 Solve problems ENWW Clear jams from the input tray A CAUTION Do not use sharp objects such as tweezers or needle nose pliers to remove jams Damage caused by sharp objects is not covered by the warranty When removing jammed paper pull it straight out from the product Pulling jammed paper out of the product at an angle can damage the product NOTE Depending on where the jam is located some of the following steps might not be necessary 1 Remove Tray 1 and lift the jam access door above the tray 2 With both hands grasp the paper and caretully pull it free from the product ENWW Paper feeds incorrectly or becomes jammed 175 3 Open the rear door CAUTION The fuser located in the back of the product is hot Wait for the fuser to cool before continuing 4 With both hands grasp the paper and carefully pull it free from the product 5 Reinsert the tray 176 Chapter 6 Solve problems ENWW 6 Close the rear output door 7 Print a cleaning page which removes excess toner from the paper path b ENWW From the Home screen touch the Setup N button Touch the Service menu Touch the Cleaning Pag
138. ecneeeeeeeeeeeseeeeeeteeeeeees 121 Step 7 Test the fax receiving functionality ccss gtsdeoassheaashcoadedanrradecd anges oveaeaetcastetned ve 121 Step 8 Try sending a print job from a computer eeeececeeeeeceeeeeeeeeeeeeeteeeeeeetteeeeeees 121 Step 9 Test the walk up USB printing functionality cccceccccesscceeeseeeeeeeeeeeetteeeeees 122 Troubleshooting process cack yon dis eanlasanten tuateeaacel nenurenadetuaw rae dats tutanute vadaccuma arcane meteades 122 Power subsystem ersin ret wae e rae ate Oa a a a a aes 122 Poweron Cheeks nesie pees e a E ieee e e E E aE NEES 122 Tools for troubleshooting ss 4c 2 iuasticerv aieus deoas coanidsd plese steps nea ps tc neny adi Sia Sie voiced Blesh asa tan Merion 123 Component diagnostics inesi a iin elas EE E tear cla E A EE E EEEE 123 LED rail nOStes ta E O A A tones udeuecuattenes 123 Network LEDS minns aa aa R rete E E E aay 123 Control panel LEDS cvsomsvessudiwt aaeois Gir sinbocisihwenin olataurecamanats 123 Controkpanel diaqnOsties c lt 2aiseeccezavn see pinssicansvevacs se oesee can ese Raa Rees 124 Engine Didgnostics sta ie veces nn ae eeeay reat ede aie eee 124 Engine test eninin tnes a A A E eaS 124 Use the HP ToolboxFX software sdesickedvavencedantodies vloessuacniidentdeseasndvavesnadaeedinnebvtaecendk 125 View the HP ToolboxFX lt 2 canta teiresiseciesecaietanteeuodeasanenuaaye tinge ouaastennteciieos 125 Se U EEEE A E EEEE EE E EE ESE ET 125 FAK e ET E E E
139. ect administrative rights are only required to run the EXE package The user can then connect the product without administrative rights For a network connection the EXE package will copy files to the driver store create the port install the print driver and create the printer object Supported operating systems e Microsoft Windows XP e Microsoft Windows XP 64 Bit Edition e Microsoft Windows Server 2003 e Microsoft Windows Server 2003 64 Bit Edition e Microsoft Windows Server 2008 44 Chapter 2 Windows software description ENWW e Microsoft Windows Server 2008 64 Bit Edition e Microsoft Windows Vista e Microsoft Windows Vista 64 bit e Microsoft Windows 7 Install and run the HP DDU Install the HP DDU Copy the files to the administrative computer If using the self extracting EXE file just copy it to the administrative computer then double click it will expand the files into the proper directory structure DDU does not require an installation program All of the files are contained in the Driver Deployment Utility directory DDU does not require any registry entries Run the HP DDU 1 Create the printer driver package to deploy by opening the HP DDU application This can be done by double clicking HPDDU EXE which is found in the Driver Deployment Utility root directory This utility packages the print driver and the code needed to stage install the print driver into an EXE file and a CAB file An in
140. ectional communication by using the Update Now feature For more information see Update Now on page 22 The following tables show the availability of EAC for various operating systems and network environments that support bidirectional communication EAC availability in Microsoft Windows and Microsoft Share Connection type Microsoft Share 2000 XP 2000 XP host with 2000 XP client Windows Server 2008 Windows Vista USB Network Jetdirect TCP IP x x x IPX SPX x x x Standard TCP IP HP x x x TCP IP MS x x x IPX SPX HP x x 7 Direct connect Parallel USB Network Jetdirect TCP IP x x x IPX SPX x x x Standard TCP IP HP x x x TCP IP MS x x x IPX SPX HP x x X ENWW 1 This column represents the following Microsott Share contigurations Windows Windows XP Windows Server Windows Server 2008 or Windows Vista host with Windows 2000 Windows XP Windows Server 2003 Windows Bevel 2008 or Windows Vista client Driver configuration for Windows 21 Table 2 4 EAC availability in Novell Netware environments Method Connection type Novell Netware 4 x Netware 5 x Bindery queue NDS queue Bindery queue USB Network Jetdirect TCP IP x x x IPX SPX Standard TCP IP HP TCP IP MS IPX SPX HP Bidirectional functionality is supported only with the client software trom Novell It is not supported with Microsoft Client Service for NetWare Update Now If you have modif
141. ector based graphics Using glossy paper in combination with this setting provides the maximum enhancement Photo Adobe RGB 1998 Select Photo AdobeRGB 1998 for documents that use the AdobeRGB color space rather than sRGB For example some digital cameras capture images in Adobe RBG and documents that are produced with Adobe PhotoShop use the Adobe RGB color space When printing from a professional software program that uses Adobe RGB it is important that you turn off the color management in the software program and allow the product software to manage the color space 94 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW Vivid sRGB None The Vivid sRGB feature instructs the printer to increase the color saturation in the midtones Less colorful objects are rendered more colorfully This value is recommended for printing business graphics Select None to instruct the printer to print RGB data in raw device mode To render documents properly when this option is selected you must manage color in the program in which you are working or in the operating system A CAUTION Use this option only if you are familiar with the procedures for managing color in the software program or in the operating system Document preview image ENWW The document preview image is a line drawn image of a page that represents graphics and text The document preview image is always oriented so that the contents
142. ed on a solid level surface 1 Is the operating environment within the specified parameters Is the product exposed to direct sunlight Step 3 Check the control panel for error messages 120 The control panel should indicate ready status If an error message appears resolve the error Common problems that result in control panel error messages include the following Paper incorrectly installed in the tray Paper guides not aligned with the paper stack in the tray Chapter 6 Solve problems ENWW Step 4 Test print functionality 1 From the control panel Home screen touch the Setup N button 2 Open the Reports menu and select the Configuration Report item to print the report 3 If the report does not print make sure paper is loaded in the tray and check to control panel to see if paper is jammed inside the product NOTE Make sure the paper in the tray meets specifications for this product Step 5 Test copy functionality 1 Place the configuration page into the document feeder and make a copy If paper does not feed smoothly through the document feeder you might need to clean the document feeder rollers and separation pad Make sure the paper meets specifications for this product 2 Place the configuration page onto the scanner glass and make a copy 3 If the print quality on the copied pages is not acceptable clean the scanner glass and the small glass strip Step 6 Test the fax sending functional
143. eeeeeeeeees 229 The Communication error Message Appears eeeeeeeeeeeeeeeeeees 230 The Fax storage is full message appears eeeeeeceeeeeeeeeeeeeees 231 The Fax is busy message appears ccceeeceeceeeesteeceeeeesteeeees 231 A fax is received but does not print cccccccceceessceeeeeenseeeeesesseeeeseeteeeeess 231 The Private Receive feature is OM ccccccccceesesceeeceesesteeeeeseeseeees 231 Sender receives a busy signal sas ji ncss lessdowsvanorerasncaddiaseabubsncdaiegebusckonsamsnhenindes 232 A handset is connected to the product c ceccceeesteeeeeteeeeeeees 232 A phone line splitter is being used ccccceceeeseeeeeseeeeesteeeeetaes 232 No dial fone seirene eana E E 232 Cannot send or receive a fax on a PBX line ccecceceeeeeeeeetteeeeeeeeeeeeeaes 232 Salve general fax problems js syisvrsnuvresacevancorseeeecdeied cothdvererssaunapaidrsraderiavaanneeeanatenss 233 Faxes are sending slowly c civsianduiunatentiawanamnnenteinunnnmusent 233 Fax g ality IS POOT senose eiii i a i 234 Fax cuts off or prints on tWO pages ccccceececeeessseecesneeeeeeseeeeeseteeeeessaeees 234 Produckopddl sanen e a acai emnet ae Ln Rete E 235 7 Engineering Details sssisssisscssssostsosissnssssessssssenucseuosrosoceoboro tssis edninecos inssi iadeo sesso dd ausus isas asiis 237 Pim HAI MITA siir a a E E ae acre E E A ote Rao 237 Printing printready documents lt x ssiciessiie lanewieradarsewinarselleda
144. eeeeeeeeseneeceseeesneeeneeesneeeneeesereees 34 Figure 2 5 HP LaserJet Send Fax dialog box user interface ecceesseesseeeeseeeeneeeeneeceseeeetaeeeteeeeneeeess 36 Figure 2 6 Package Source 3c ee caipactncs ca cas bpd ienasi rier nesieee eeo inr ernster eonenni eno 46 Figure 2 7 Network Settings 5iii iccieisci isssnivesderorabivscierevandes onceavenrpbeninededsunntesdveenbesnndaunvedebendniiensneasiioudess 47 Figure 2 8 HP DDU Driver Configuration settings s 0 ccsavssvaansaorovonsenansraderwruwnviedseasdondvanindvadovontate eatadsawenameses 49 Figure 3 1 Installer screen Welcome Back a j cyississsarsanaesqusdeoisnernatonapeaeasncvenniypanaedwaeprennaunoannevenis 60 Figure 4 1 An Incompatible Print Settings message cccccceeseeseneeeeeceeeeeeeeeeeeseneeeseteeeneeenens 65 Figure 4 2 The default appearance of the Advanced tab eccceeceeeeseeeeeceeeneeeeeeeesneeesenseseneeeseeeeens 66 Figure 4 3 Paper Quality tab ico acatasaxmaucuiviendumentokeemaneaenaminenaannn as eee anuanOs 70 Figure 4 4 Effects tab si orercsticrsceinciovecientnnideilenntedhucat uccee tiara scr nsiee min alRenaaeateldnan lisa senieandeeatansbmnetaamntannes 78 Figure 4 5 Finishing tab ecen wees Gams aaa ane ee ana 85 Figure 4 6 Print on Both Sides Instructions dialog box ssii i5 c01 anesincaonseaaitansieaanun sn iebaiwpannttoinghebalanunlanaacubadans 88 Figure 47 Color Tabira e a a e Coates eaae e ala dataneie headin 92 Figure 4 8 Services gis
145. eeeeeseseeeneteeeeesaaes 244 Installation TATE Sposa searsgcvtccaxo bebe renee set punter hauls nea os aceomnvae tb aencaionentieba pa astemombansaneeeaphenaaen 245 l INTRODUCTION sii gence bene tsp titanate ibaa ea E 245 ENWW xiii PURPOSE OF THAIS DOCUMENT saimiensdadedenaopntvatuieseqasaaanmennnmnunamnementesye 245 SUPPORTED OPERATING SYSTEMS ic suskvissveveenarericarersnaersracanataseracissanarsxe 245 OVERVIEW OF THE PRINTING SYSTEM COMPONENTS 00ccce0eeeeees 246 Drivers uniesie o E E E R E E 246 Software Applications ays aariesastenitonivcontiensenmeaioedonchivaakiaaiaseioveans 246 HP ToolboxFX cresson niece A emis 247 HP Help and Learn Center cccccccesseceeseneceeeeneeeeeteeeesseeeeeees 247 Uninstaller aoao eeen a es R A 247 Il INSTALLATION INSTRUCTIONS 0 cceseeecececceeeeeeeeeeeeeseeseeeeeeaeeseeeeeessaneneeeeeeaaens 247 INSTALLING SOFTWARE os ccdnonsivnadusa cuttin hecinn tentenawasaibaganneaacniucidpeatintaenunen en 247 INSTALUNG SOFTWARE accjsscerininieiraeaenrnnnn aan E S 247 Printing system installation from the CD or Internet download for network and USB connections cccccceeeseeeeesseeeeeseeeeeeseseeeeees 248 Portselechion seisein a E ean 248 Printer driver only Add Printer Windows XP Windows Server 2003 and Windows Server 2008 ceeceecccesesseeeccceusnseeeceeeees 248 Printer driver only Add Printer Windows Vista and Windows 7 249 UNINSTALLER 322228 ccdesediivncsecdoc eds t
146. eesae 175 Clear jams from the output Bin ayiisisnte ein cndunyelater weedy tarem iets tw u tons 178 PA PFOVE PKIGN CUCM sh E A EEE EEN A E cuudiass 179 Use the correct paper type setting in the printer driver ccccccceeeeeeeeeetteenteeeeeeees 179 Change the paper type setting for Windows cccccccecseeeceetteeeeeeeeeeeses 179 Change the paper type setting for Mac ceccceesscceesseeeeeeseeeeeseeeeeeeeeeeess 179 Adjust color settings in the printer driver cccceeeeseeeecceeeeenceeeeeeeeeeeeeeeeseeetaeeeeeess 180 Change the color theme for a print job ccccccceceeseeceeeeeseteeeeeestteeeeeees 180 ENWW Change the color options wx pad val een dass cuxeicn Maou aunmeve ees 180 Use paper that meets HP specifications c cecesenstvuss encase vysatyaedasnetesis gua venanedeaddnavnededase 182 Print a cleaning page coc itana ei ease et erected a itor edu eee E tates 182 Calibrate the product to align the colors wa swrcenicneue Wetsuit dinner minmscawendies 183 Check the print cartridges tac ccc conannianeetatien awaieatios ssienbed wadiee aga akon ehate ate meant 183 Print the Supplies Status page nee aed a ee a a lt ae 184 Interpret the Print Quality Page coic daicrnasdedecadecaagediersd danse ledeusadueend naa eteat 185 Inspect the print cartridge for damage ccsseseeesteceeeceeeeeseeeetseeestseeeeees 186 Repetitive image defects x insu0 cctuysevoeaian temiutders Siemon sane wearnteatan MSan
147. eesaeeeeecsesseesseseeeeneaaes 112 HP LaserJet Pro CM 14 10 Color MFP Series PPD iviecairecerderatdeaneesreeideievaerrerssiatecrnweesl 112 HP LaserJet Pro CM1410 Color MFP Series PDE cccccceeseeeseteeeeeeeeeeeennnneeeeeeees 113 HP USB EWS Gateway ccccccesseeeteeeeneeeeeeeeeeceeececececeeeeeceeeaaaeaaaeaeaeaeeetseeesenteeeeess 113 HP lasset Utilitare a asian S 113 Supported printer drivers for Macintosh ccccccssccceeeseceeeeeneeeeeseeeeecseteeeeeseeeeeeeees 113 Priority for print settings for Macintosh 5 cioccsdsabndqnswsantediwaddanciesabadesndeatacadiadeaumennoncerdsas 113 Change printer driver settings for Macintosh cccseseceeesseeeeeeseeeeeeeseeeesneeseneeees 114 Software for Macintosh Computers 0 iccs cc0 c0ceseessescssscerianesesesnsavenanscestanededenssdeceunees 114 AP laserJet URII cronni an E E 114 Open the HP LaserJet Utility cccsaseeuss seas seseunchergeonsttancncesiarcalagens 114 Embedded Web Server i ancenisarsanerss haxastawenedalegsonennpranmesanddaandpastneamungraness 114 Ayala Biliyi sern e a AEE E E R ae EH 114 Printing system software on the Web cc cccccesecceseseeeeeeneeeeeeseeeeseseeeensns 115 In box printing system software CD cccceccceeesseeeeesseeeeeeeseeeeessneeeeenaeees 115 M cintoshdis keenean a neanateeN 115 Macintosh install and uninstall instructions aan scndvarcseaciviartsvansnedilanveatnuntansdeen dine averatunanstaeanvides 116 Install the
148. eful only for the few software programs that do not set an orientation The Orientation group box contains the following options e Portrait The top edge of the document is the shorter edge of the paper e Landscape The top edge of the document is the longer edge of the paper e Rotate by 180 degrees This creates a landscape or portrait orientation in which the image is rotated 180 This setting is useful for printing prepunched paper You can toggle orientation between portrait and landscape by clicking the document preview image If you select the Rotate by 180 degrees check box no change occurs in the document preview image ENWW Finishing tab features 91 Color tab features NOTE The Color tab is located on the Printing Preferences tab set For information about how to access these tabs see Printing Preferences driver tabs on page 62 Use the Color tab to specify predefined color option settings or to fine tune the color treatments and halftoning Color output can also be converted to grayscale The Color tab is shown in the following figure Figure 4 7 Color tab HP LaserJet CM1410 Series PCL 6 Copy 1 Printing Preferences Advanced Printing Shortcuts Paper Quality Effects Finishing Color Services Color Options Automatic Manual Settings C Print in Grayscale Color Themes RGB color Default sRGB cA The Color tab contains the following sets of controls
149. eiues ens 187 Use the printer driver that best meets your printing needs ceeeeseeeeeeeeeeeeeeeeteees 188 Improve print quality for copies sscaaceoeccuseved ov Cavs cumien cays vd een sveeues ard RE 189 Clean the produerl stsinaiocsusphdag oninure tues a E E T a a taken totueTeumourvors 190 Glean the elenon e a tie R E R E canes E E EE R 190 Gleanicthe paper path 4raitiacias ey eee e a e a a AA A 190 Clean the paper path from the product control panel cceeesseeeeteeeeeeees 190 Clean the scanner glass strip and platen cccccecceeeeeeeeneeeeeeeeeeeeeeeeeeeeeesnaeeeeeeeee 190 Clean the document feeder pickup rollers and separation pad cccceeceeeeesteeeeeees 191 Clean the touch Snecma te antec neose e E Ee cutee und ETE TESEN E E 192 The product does not print or it prints slowlys icccsieet eae lates Raves eee eee 193 The prod ct doesnot priini areen ai ite a a EEEE Oi etude TE ea E aT a dy 193 The product prints Slow yt tc svecxtuiiansivareddivactunearad eisenedscegioacutdneeeeadsnaat anes 194 Salve walk up USB printing problems tay cossa eevee Gee cease kp 20k Wao ue a rk mae 195 The USB Flash Drive menu does not open when you insert the USB accessory 0666 195 The file does not print from the USB storage accessory cceeeeeceeeeeeceeeeeeetseeeeeseeeees 195 The file that you want to print is not listed in the USB Flash Drive menu 00e008 195 SOLVE CONMEECHVIN problems arnore iaa
150. elay Off Specifies the amount of idle time before the product enters sleep mode 1 Minute 15 Minutes 30 Minutes 1 Hour 2 Hours Time Date Settings for time Sets the time and date setting for the product format current time date format and current date Product Security On Sets the product security feature If you select the On setting you must set a password Off At Very Low Black Cartridge Stop Sets how the product behaves when the black print cartridge reaches the very low threshold Prompt e Stop The product stops printing until you replace the Continue print cartridge e Prompt The product stops printing and prompts you to replace the print cartridge You can acknowledge the prompt and continue printing e Continue The product alerts you that the print cartridge is very low but it continues printing Color Cartridges Stop Sets how the product behaves when one of the color print cartridges reaches the very low threshold Prompt e Stop The product stops printing until you replace the Continue print cartridge Print Black Prompt The product stops printing and prompts you to replace the print cartridge You can acknowledge the prompt and continue printing Continue The product alerts you that the print cartridge is very low but it continues printing Print Black When a color print cartridge becomes very low the product prints in black only to prevent fax interruptions To configure the product fo print in colo
151. ephone cord is plugged into the correct port on the back of the product 2 Check the phone line by using the fax test a On the control panel open the Setup menu and then open the Service menu b Select the Fax Service option c Select the Run Fax Test option The product prints a fax test report 204 Chapter 6 Solve problems ENWW ENWW The report contains the following possible results e Pass The report contains all of the current fax settings for review e Fail The cord is in the wrong port The report contains suggestions for how to resolve the issue e Fail The phone line is not active The report contains suggestions for how to resolve the issue 3 Verify that the product firmware is current Print a configuration page from the control panel Reports menu to obtain the current firmware date code Go to www hp com 1 Click the Support amp Drivers link 2 Click the Download drivers and software and firmware link option 3 In the For product box type the product model number and then click the Go button 4 Click the link for your operating system 5 Scroll to the Firmware section of the table o If the listed version matches the version on the configuration page you have the most current version o If the versions are different download the firmware upgrade and update the firmware on the product following the instructions onscreen NOTE The product must be connected to a computer with in
152. er is installed by default e The HP PCL 5 Universal Printer Driver UPD This printer driver is not installed by default To install the HP PCL 5 UPD use the Microsoft Add Printer wizard e The HP postscript level 3 emulation printer driver and PostScript printer description PPD file for printing with PS level 3 emulation This printer driver is not installed by default To install the HP PS printer driver use the Microsoft Add Printer wizard e The HP LaserJet Send Fax driver e Scan drivers Windows Image Acquisition WIA driver for Windows XP and Vista WIA scanning can be started from a WIA compliant program or from the computer WIA has its own user interface that is relatively simple and does not contain the wide range of image quality options that are available in the TWAIN driver user interface e TWAIN driver TWAIN is an industry standard scanning protocol Scanning from the product can be initiated from any TWAIN compliant software program Readiris Professional Converts scanned images into text that can be edited in word processing programs v12 0 text recognition software by IRIS The user interface is localized into six languages However the software supports textrecognition in 124 languages Readiris Professional supports text recognition in 2 byte Asian characters You must have your operating system set up to display 2 byte characters in order to see the text NOTE For better text recognition scanning results
153. er pages of a document The following are the Print pages on different paper options e Pages in document Select which pages are customized the First page the Last page or specify a page range with the Pages option e Paper source The Paper source setting specifies the source tray to use for printing a document The list of source trays depends on the accessories that are installed Any optional trays that are installed through the Device Settings tab also appear here e Paper type The Paper type drop down menu shows all of the paper types that the HP LaserJet Pro CM1410 Color MFP Series supports amp NOTE The same type of paper is used for the entire print job When you change the type and source of the paper and covers the settings remain configured until you close the software program Insert blank or preprinted pages Use the Insert blank or preprinted pages options to designate where to insert preprinted pages or blank pages into a document ENWW Paper Quallity tab features 75 The following are the Insert blank or preprinted pages options Blank or preprinted sheet before page s Specify where in the document you want to insert blank or preprinted pages by designating the page numbers or page ranges that the blank or preprinted pages will precede For example to insert a blank or preprinted page on page four specify 5 in the Blank or preprinted sheet before page s option Paper source The Paper source sett
154. eries Welcome Back Select from the options below Uninstall l bd Proceed with uninstall of this product Connect another HP LaserJet Device Quickly Install another HP LaserJet device using software already loaded on this computer The Welcome Back screen contains the following options e Uninstall Click this option to uninstall the printing system software e Connect another HP LaserJet Device Click this option to quickly install another HP product using software that is already loaded on the computer e More Options Click this option to open the product documentation on the CD including the User Guide Admin Documentation and Software ot to gain access to specialized drivers and product support on the Web e Cancel Click this button to close the Installer 60 Chapter 3 Install Windows printing system components ENWW 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows Introduction ENWW This chapter describes the features of the HP LaserJet Pro CM1410 Color MFP Series PCL 6 Print Driver for Windows XP 32 bit and 64 bit Windows Server 2003 32 bit and 64 bit Windows Server 2008 32 bit and 64 bit Windows Vista 32 bit and 64 bit and Windows 7 32 bit and 64 bit You can control print jobs from several places e the product control panel e the software program print dialog box e _ the driver user interface Generally for features that are duplicated in more than one loc
155. ering of logical pages on a physical sheet of paper does not change ENWW Advanced tab features 69 Paper Quality tab features NOTE The Paper Quality tab is located on the Printing Preferences tab set For information about how to access these tabs see Printing Preferences driver tabs on page 62 Use the Paper Quality tab to specify paper size type and source You can also use this tab to specify different paper selections for the front cover first page other pages last page and back cover of the document The following figure shows the Paper Quality tab Figure 4 3 Paper Quality tab amp HP LaserJet CM1410 Series PCL 6 Copy 1 Printing Preferences Advanced Printing Shortcuts Paper Quality Effects Finishing Color Services Paper Options Paper sizes Letter v Paper source Automatically Select v Paper type Unspecified Print Quality Special pages Covers ImageREt 3600 Print pages on different paper The Paper Quality tab contains the following control sets e Paper Options e Document preview image e Print Quality Paper Options The settings specified in the Paper Options group box on the Paper Quality tab apply to all of the pages of the document 70 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW The settings in the Paper Options group box are described in the follow
156. ets of driver tabs the Printing Preferences tabs and the Properties tabs The settings that you make on the Printing Preferences driver tabs control the driver default settings for each user s profile Installable options can be configured in Properties driver tabs Printing Preferences driver tabs The Printing Preferences driver tabs change the default settings that are used across all software programs To gain access to these tabs follow these steps 1 In Windows Vista and Windows 7 click the Start button click Control Panel click Hardware and Sound and then click Printers In Windows XP Windows Server 2003 and Windows Server 2008 click Start click Settings and then click Printers and Faxes 2 Right click the product icon 3 Click Printing Preferences The following Printing Preferences printdriver tabs are available e Advanced e Printing Shortcuts e Paper Quality e Effects e Finishing e Color e Services 62 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW Properties driver tabs This set of tabs controls the driver behavior and driver connections To gain access to the Properties tabs follow these steps 1 In Windows Vista and Windows 7 click the Start button click Control Panel click Hardware and Sound and then click Printers In Windows XP Windows Server 2003 and Windows Server 2008 click Start click Settings and then click Printers and Faxes 2 Rightcli
157. fect Block Faxes Help Block Faxes provides a list of all numbers that are blocked Add modify or delete blocked fax numbers on this tab The Help folder contains links to the following main pages e Color Printing Tools Open Microsoft Office Basic Colors or the full palette of color with associated RGB values Use the HP Basic Color Match to adjust spot colors in your printed output 128 Chapter 6 Solve problems ENWW System Settings The HP ToolboxFX System Settings tab contains links to the following main pages e Device Information View information about the product such as the product description and a contact person e Paper Setup Change the product paper handling settings such as default paper size and default paper type e Print Quality Change the product print quality settings e Print Density Change the print density settings such as contrast highlights midtones and shadows e Paper Types Change the mode settings for each media type such as letterhead prepunched or glossy paper e System Setup Change the system settings such as jam recovery and auto continue Change the Cartridge low threshold setting which sets the toner level that causes a Low toner pop up alert e Device Polling Change the product polling settings which determine how often HP ToolboxFX collects data from the product e Save Restore Settings Save the current settings for the product to a file on the computer Use this fil
158. figuration process consists of three basic steps e driver acquisition e driver configuration e driver installation and deployment These steps can be accomplished in different ways depending on the tool that is being used to define the configuration The driver configuration process is supported through three distinct tools All three are designed with the same basic user interface Ul controls for interacting with the CFG file but are packaged ENWW Driver configuration for Windows 23 differently either to support established product installation workflows or to leave the deployment and installation of the driver entirely up to the user The following tools support driver preconfiguration e HP Driver Configuration Utility The HP Driver Configuration Utility is a small standalone Windows software program that the administrator can use to open the CFG file that is associated with a particular driver and make modifications that are applied when that driver is installed on the target computer It is intended for use in environments that have an established process for deploying drivers This is the preconfiguration tool of choice to support any Novell or HP Print Server Appliance PSA and Point and Print environments It is used in the way that any ordinary Windows software program is used The HP Driver Configuration Utility is available at the following Web site www hp com go dcu e HP Web Jetadmin Driver Configuration Plugin
159. figure the fax settings for both the software and the product control panel Run the utility even if you have already configured the fax settings The settings in the HP LaserJet Fax Setup Utility are used by HP ToolboxFX to run other faxing features such as the fax cover page NOTE You can also start the HP LaserJet Fax Setup Utility by clicking Start selecting Programs or All Programs selecting HP selecting the name of the product and then clicking HP Fax Setup Wizard NOTE For more information about faxing see the HP LaserJet CM1410 MFP Series User Guide which is available on the printing system CD that came with the product HP LaserJet Fax Setup Utility 35 HP LaserJet Send Fax software Use the HP LaserJet Send Fax software to send faxes from the computer To use the HP LaserJet Send Fax software click Start select Programs or All Programs select HP select the name of the product and then click Send Fax Figure 2 5 HP LaserJet Send Fax dialog box user interface 1 HP LaserJet Send Fax Device HP LaserJet CM1410 MFP Series PCL 6 10 10 48 117 Fax To Fax Number Name Company Phone Book Create Recipient List Resolution C Standard Fine Superfine Include With Fax Attach Scanned Pages Defaults Send Preview Cancel Help NOTE The HP LaserJet Send Fax software works with HP ToolboxFX If you turn off HP ToolboxFX you cannot use some of the HP LaserJet Send Fax software fe
160. first page of the fax on the report Fax Error Report On Every Error Sets whether the product prints a report after a failed On Send Error fax job On Receive Error Never Print Last Call Report Prints a detailed report of the last fax operation either sent or received Fax Activity Log Print Log Now Print Log Now Prints a list of the faxes that have been sent Auto Log Print from or received by this product Auto Log Print Automatically prints a report after every fax job Print Phone Book Prints a list of the speed dials that have been set up for this product Print Junk Fax list Prints a list of phone numbers that are blocked from sending faxes to this product Print Billing Report Prints a list of billing codes that have been used for outgoing faxes This report shows how many sent faxes were billed to each code This menu item appears only when the billing codes feature is turned on Print All fax Reports Prints all fax related reports Send Options Send Fax Later Allows a fax to be sent at a later time and date Broadcast Fax Sends a fax to multiple recipients Fax Job Status Displays pending fax jobs and allows you to cancel pending fax jobs ENWW Tools for troubleshooting 147 Menu item Sub menu item Sub menu item Fax Resolution Standard Fine Superfine Photo Description Sets the resolution for sent documents Higher resolution images have more dots per inch dp
161. formational XML file is also created and can be used to identify the package selections 2 Run the new printer driver package created in step 1 on the client computer It can be copied to the client computer and run by double clicking or it can be run from a server by pointing to it and double clicking The package can also be run in a batch file For a direct connect package the HP DDU will silently copy the printer driver files into the Windows driver store and exit Prior to exiting an optional dialog can be shown to prompt the user to connect their product after the files are copied Upon completion of the package executable when the user connects the product to the computer the operating system will install the product using Plug and Play software amp NOTE Ifthe product is never connected to the computer the product will not be installed For a network package the HP DDU will silently copy the printer driver files into the Windows driver store and then install the product using the network information entered by the administrator Use the HP DDU The HP DDU user interface is divided into the following sections e Package Source describes the package type and printer driver location that you want to create e Package Target identifies the name and location of the installation package e Create Package initiates the package creation process ENWW HP Driver Deployment Utility 45 Figure 2 6 Package Source D HP Dri
162. ftware program that was used to create the document Normally the document is printed by opening the original application and printing it to a file or is printed by means of a distribution method such as internet downloading The following print ready file formats can be sent directly to the HP LaserJet Pro CM1410 Color MFP Series product without first opening the original software program HP LaserJet Printer Control Language PRN Portable Document Format PDF Postscript PS Text TXT Use one of the following methods to send print ready files to your product NOTE The examples that are used here are for printing PDF documents However any print ready file type can be substituted Print ready file printing by using FTP through a browser Complete the following steps to print printready files directly by using FTP through a browser NOTE The following instructions can be used on Windows or Macintosh operating systems 1 4 5 Make note of the TCP IP address on the Embedded Jetdirect page The HP Embedded Jetdirect page is the second page of the configuration page printout Open a browser window In the address line of the browser type ftp lt IPADDRESS gt For example if the TCP IP address of your product is 192 168 0 90 type the following FTP 192 168 0 90 Locate the print ready file for the product Drag and drop the printready file onto the PORT1 icon in the browser window
163. g extension file can specify one or more PDEs to load in the Print dialog box to provide HP printer specific features A printing dialog extension PDE is a way to extend the Print dialog box in Mac OS X with custom printer features A PPD file and printing dialog extension PDE for a printer are bound to a printer queue when the queue is created HP USB EWS Gateway For network connected printers the EWS can be accessed directly by typing the network IP address or DNS name of the product into the Web browser HP USB EWS Gateway software which is automatically installed allows a Web browser to access the product s EWS if the product is connected using a USB cable Click the Utility button when using a USB connection to access the EWS though the Web browser HP LaserJet Utility Use the HP LaserJet Utility to configure administer and set up product features that are not available from the printer driver You can use the HP LaserJet Utility with HP printers connected via USB and ethernet Supported printer drivers for Macintosh The HP installer provides Postscript Printer Description PPD files Printer Dialog Extensions PDEs and the HP Printer Utility for use with Macintosh computers The PPDs in combination with the Apple postscript printer drivers provide access to device features Use the Apple postscript printer driver that comes with the computer Priority for print settings for Macintosh Changes to print settings are
164. g product for poll transmission The sender must load a document to transmit and then configure the product for polling 321 There was a communication error with the Reattempt the fax transmission at a different time receiving fax product due to poor telephone line when telephone line conditions have improved conditions 322 324 Telephone line conditions were too poor to senda 1 Reattempt the fax transmission at a different ENWW fax time when telephone line conditions have improved 2 If the session fails after transmitting several pages of a large document retransmit the document as several smaller documents Solve fax problems 211 Table 6 5 Fax send error codes continued Error code Description Solution 325 328 ECM error Telephone line conditions were very poor 1 Reattempt the fax transmission at a different time when telephone line conditions have improved 2 If the error persists disable ECM Errors may still occur and may result in a degraded image quality on the received page However the ability to transmit the entire document will be improved 329 331 The sending product has reported that one or more 1 Reattempt the fax transmission at a different pages have been received non ECM mode with time when telephone line conditions have excessive errors This error does not result in the improved session being terminated immediately Subsequent page transmission can still occur
165. ges e Set the Default Paper Size setting Faxes print on a single size of paper based on the Default Paper Size settings Open the Setup N menu b Open the System Setup menu c Open the Paper Setup menu d Open the Default Paper Size menu e Select the correct setting e Set the paper type and size for the tray used for faxes e Turn on the Fit to Page setting to print longer length faxes on letter or A4 size paper a Open the Setup N menu b Open the Fax Setup menu c Open the Advanced Setup menu 234 Chapter 6 Solve problems ENWW d Open the Fit to Page menu e Select the On setting E NOTE Ifthe Fit to Page setting is off and the Default Paper Size setting is set to letter a legal size original prints on two pages Product updates Software and firmware updates and installation instructions for this product are available at www hp com support CM 141 Oseries Click Downloads and drivers click the operating system and then select the download for the product ENWW Product updates 235 236 Chapter 6 Solve problems ENWW 7 Engineering Details Introduction This chapter presents engineering detail for the following topics e Printing print ready documents e Paper and print media e Parameter settings fax data store parameters e Installation notes ENWW Introduction 237 Printing print ready documents Several methods are available for printing documents independently of the original so
166. gure the receiving fax product to use different configurations toggle the ECM state or select a slower reception speed 367 372 373 377 ECM error 378 and 379 The sending product appears fo be stuck on N A Chapter 6 Solve problems ENWW ENWW Table 6 5 Fax send error codes continued Error code Description Solution 380 The sending product has failed to issue a valid Send from another product response fo a CTC frame This occurs during ECM transmission after multiple retransmissions of erred data 381 One of the following has occurred 1 Reattempt the fax transmission at a different time when telephone line conditions have The sending product has failed to respond to improved a fax command from the receiving product due to the connection being interrupted 2 If the error persists disable ECM e The sender has touched the Cancel 9 button while the reception was in progress 382 The sending fax product has been holding off the 1 Resend the document as two or more receiving fax product from continuing the ongoing separate fax transmissions Wait several transmission due to a temporary low memory minutes between the end of one transmission condition at the sending product If this hold off and the start of the next transmission period exceeds a product s specific timeout value the session will terminate 2 If the error persists disable ECM 383 One of the following has occurred
167. hat came in the product box The Fax storage is full message appears e Turn the product off then on e Print all of the faxes and then have the sender resend the fax e _ Ask the sender to divide a large fax job into smaller sections and then fax them individually e Make sure that the resolution of the sending fax machine is not set to the Photo setting or the Superfine setting a From the Home screen touch the Setup amp button Open the Fax Setup menu c Open the Advanced Setup menu d Open the Fax Resolution menu e Select the correct setting e Cancel all fax jobs or clear the faxes from memory The Fax is busy message appears e The product cannot receive a fax while attempting to send one Cancel the fax send and try sending at a later time e Allow the product to try sending the fax again A fax is received but does not print The Private Receive feature is on e When the Private Receive feature is activated received faxes are stored in memory A password is required to print the stored faxes e Enter the password to print the fax If you do not know the password contact the product administrator NOTE Memory errors might occur if the faxes are not printed The product will not answer if the memory is full ENWW Solve fax problems 231 Sender receives a busy signal A handset is connected to the product e Make sure the phone is hung up e Change the Answer Mode option to match the
168. he Automatic setting from the control panel a From the Home screen touch the Setup N button Open the Fax Setup menu c Open the Basic Setup menu d Open the Answer Mode menu e Select the Automatic setting An answering machine is connected to the product ENWW Set the Answer Mode option to the TAM setting and plug the answering machine into the telephone port a From the Home screen touch the Setup amp button Open the Fax Setup menu c Open the Basic Setup menu d Open the Answer Mode menu e Select the TAM setting If the TAM setting is unavailable set the Answer Mode option to the Automatic setting Set the Rings to Answer setting to at least one ring more than the number of rings for which the answering machine is set a From the Home screen touch the Setup amp button b Open the Fax Setup menu c Open the Basic Setup menu Solve fax problems 227 d Open the Rings to Answer menu e Select the correct setting e Plug the answering machine into the telephone port e Ifthe product has a telephone handset connected set the Answer Mode option to the Fax Tel setting to route calls to the correct device When detecting a voice call the product generates a ring tone that alerts you to pick up the telephone handset From the Home screen touch the Setup button Open the Fax Setup menu c Open the Basic Setup menu d Open the Answer Mode menu e Select the Fax Tel setting A tele
169. he back of the computer o Verify that the product is turned on The product will not be discovered by the software if the power is off o Ensure that your USB cable is no more than 5 m 16 4 ft in length o Verify that the USB port is enabled Some computers ship with disabled USB ports Upgrading Windows HP recommends that you uninstall HP products before upgrading to a newer supported version of Windows For example when upgrading from Windows Vista to Windows 7 uninstall your HP product using the Uninstaller program provided in the HP program group see the Uninstaller section 250 Chapter 7 Engineering Details ENWW and then upgrade to the new operating system After the operating system upgrade is complete reinstall your HP product using the latest software available at HP com IV TECHNICAL ASSISTANCE CUSTOMER SUPPORT For customer support information see the user guide or the support flyer that was in the box or call your local authorized HP dealer WEB You can also browse to the following URL s for online technical support e HP Color LaserJet CM1410 Series technical support www hp com support CM14 1Oseries e www hp com go support HP SOFTWARE AND SUPPORT SERVICES ADDITIONAL INFORMATION See either the user guide or the in box flyer for additional methods of obtaining software and support information such as printer driver distribution centers other online services fax services and other online suppo
170. he computer click Yes 6 After installation of the printing system software dialog boxes appear that allow you to print a test page register the product over the Web and set up faxing on the product Printer driver only installation instructions Microsoft Add Printer Wizard amp NOTE This printer driver only software solution provides print only functionality through a communications port that has already been created for this product USB or network connected Fax and scan functionality are not included with this software ENWW General Windows installation instructions 55 To use the printer driver only software solution with a direct USB connection a USB Print port must have already been created by a previous installation of the printing system software There are several direct USB printing system software installation options that establish a USB Print port e Complete an installation using the in box printing system software CD e Download the Recommended Solution which provides installation options identical to the printing system software CD Once a USB Print port is created by a previous direct USB installation the printer driver installation can be completed using that USB Print port Use the following instructions to install the printer driver only 1 Click Start and then do one of the following or For Windows Server 2003 and Windows XP Professional Select Settings and then click Printers and Faxes
171. he connection does not have this capability that is if it has no bidirectional mode it can only accept commands from the host and cannot report information back to the host computer Enterprise AutoConfiguration Enterprise AutoConfiguration EAC uses bidirectional communication to provide autoconfiguration functionality for installation of the print driver over a network whether you use the installer on the printing system software CD or the Add Printer wizard to install the driver Driver installation that includes EAC is configured with the same settings as the physical configuration of the product Configuration occurs without user interaction 20 Chapter 2 Windows software description ENWW Table 2 3 Method Add Printer If bidirectional communication software has been installed previously EAC is not activated and the pre existing bidirectional communication software is used to configure the print driver If bidirectional communication software has not been installed EAC installs bidirectional communication software that allows it to communicate with the product and automatically match the print driver with the actual product configuration EAC is activated during installation of the driver or whenever the Update Now feature is used If the HP LaserJet Pro CM1410 Color MFP Series product configuration changes after installation the driver can be automatically updated with the new configuration in environments that support bidir
172. he driver coordinates this function Flip Pages Up Use the Flip Pages Up check box to specify the duplex binding option By default the Flip Pages Up check box is not available It is available only when Print on Both Sides is selected The following table demonstrates the results of selecting this check box depending on the paper orientation selected on the Finishing tab Table 4 2 Page orientation Orientation Finishing tab Flip Pages Up selected Flip Pages Up not selected Portrait Short edge binding Long edge binding Landscape Long edge binding Short edge binding When Print on Both Sides is selected the document preview image changes to show a spiral binding along either the left edge or the top edge of the page In addition a folded over corner appears in the lower right portion of the preview image indicating that printing occurs on the back side An arrow on the folded over corner points in the direction that the pages would be flipped if they were bound together Shortside binding is for print jobs with pages that read by flipping over like the pages of a calendar Long side binding is for print jobs with pages that read by turning like the pages of a book 88 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW Booklet Layout The Booklet Layout drop down menu visible when Print on Both Sides is selected offers choices that are based on the current paper size The default setting for th
173. he product does not print If the product does not print at all try the following solutions 1 Make sure the product is turned on and that the control panel indicates it is ready o If the control panel does not indicate the product is ready turn the product off and then on again o If the control panel indicates the product is ready try sending the job again 2 If the control panel indicates the product has an error resolve the error and then try sending the job again 3 Make sure the cables are all connected correctly If the product is connected to a network check the following items o Check the light next to the network connection on the product If the network is active the light is green o Make sure that you are using a network cable and not a phone cord to connect to the network o Make sure the network router hub or switch is turned on and that it is working correctly 4 Install the HP software from the CD that came with the product Using generic printer drivers can cause delays clearing jobs from the print queue 5 From the list of printers on your computer right click the name of this product click Properties and open the Ports tab e If you are using a network cable to connect to the network make sure the printer name listed on the Ports tab matches the product name on the product configuration page e If you are using a USB cable and are connecting to a wireless network make sure the box is checked ne
174. he product off and then on to clear the memory Misprint Press OK Description Feed delay misprint Recommended action Verify that paper is loaded in the input tray Reload paper No dial tone Description The product could not detect a dial tone Recommended action Check for a dial tone on the phone line by touching the Start Fax button Unplug the telephone cord from both the product and the wall and replug the cord Make sure that you are using the telephone cord that came with the product Open the Service menu and touch the Fax Service button Touch the Run Fax Test button This test verifies that the phone cord is connected to the correct port and that the phone line has a signal The product prints a report with the results ENWW Tools for troubleshooting 163 No fax answer Canceled send Description Attempts to redial a fax number failed or the Redial if No Answer option was turned off Recommended action Call the recipient to ensure that the fax machine is on and ready Check that you are dialing the correct fax number Check that the redial option is enabled Unplug the telephone cord from both the product and the wall and replug the cord Open the Service menu and touch the Fax Service button Touch the Run Fax Test button This test verifies that the phone cord is connected to the correct port and that the phone line has a signal The product prints a report with the results No fax answer Redial pending Descripti
175. he software uninstall Ill LATE BREAKING INFORMATION KNOWN ISSUES AND WORKAROUNDS General e The SNMP Community Name can be set in HP ToolboxFX or the embedded Web server If the Community Name is changed to something other than public network scanning stops working e Firewall software can interfere with the HP software installer Disable the firewall before starting a network installation or the product might not be detected e Certain high speed USB 2 0 cards ship with unsigned host controller drivers If you have purchased a USB 2 0 add in card and have an unsigned driver you might experience driver installation problems or communication problems between the device and HP software It is recommended that you always use a Microsoft WHQL Certified host controller driver with your USB hardware e Functionality is limited on systems that only meet minimum system requirements Many images and videos require a system that meets the recommended system requirements for acceptable performance and reliability e Ifthe product is not detected during software installation check the following o Verify that your cable is Hi Speed USB 2 0 compliant o Ensure that your cable is connected correctly Remove the USB cable look at the end of the cable and then match it to the pattern on the USB port Make sure that it is not upside down Insert one end of the USB cable completely into the USB port on the HP product and insert the other end into t
176. hortcuts e Snapshot Photos e Labels e Labels e Create a custom printing shortcut NOTE The Printing Shortcuts tab is located on the Printing Preferences tab set For information about how to access these tabs see Printing Preferences driver tabs on page 62 Use the Printing Shortcuts tab to store specific combinations of driver settings for easy use The following figure shows the Printing Shortcuts tab Figure 4 10 Printing Shortcuts tab amp HP LaserJet M1410 Series PCL 6 Copy 1 Printing Preferences Advanced Printing Shortcuts Paper Quality Effects Finishing Color Services 4 printing shortcut is a collection of saved print settings that you can select with a single click Printing shortcuts General Everyday Printing Eco print Two sided Printing Paper source Automatically Select v Paper sizes 8 5 x 11 inches Factory Defaults Letter v Paper type Envelopes Unspecified Print on both sides No Cardstock Heavy Glossy Presentation The Printing Shortcuts tab is a new tab that appears on the HP PCL 6 Print Driver beginning with the HP Color LaserJet CM4730 MFP In previous drivers the Print Task Quick Sets appeared in most of the driver tabs and was used to capture commonly used driver settings Like Quick Sets the Printing Shortcuts tab saves commonly used driver settings under a shortcut name 102
177. i so they show more detail Lower resolution images have fewer dots per inch and show less detail but the file size is smaller Receive Options Print Private Faxes Prints stored faxes when the private receive feature is on This menu item appears only when the private receive feature is turned on The product prompts you for the system password Block Junk Faxes Add Number Delete Number Delete All Numbers Print Junk Fax list Modifies the junk fax list The junk fax list can contain up to 30 numbers When the product receives a call from one of the junk fax numbers it deletes the incoming fax It also logs the junk fax in the activity log along with job accounting information Reprint Faxes Forward Fax On Off Polling Receive Phone Book Setup Individual Setup Group Setup Prints the received faxes stored in available memory This item is available only if you have turned on the Allow Fax Reprint feature in the Fax Setup menu Sets product to send all received faxes to another fax machine Allows the product to call another fax machine that has polling send enabled Edits the fax phone book speed dials and group dial entries The product supports up to 120 phone book entries which can be either individual or group entries Delete Entry Deletes a specific phone book entry Delete All Entries Deletes all entries in the phone book 148 Chapter 6 Solve problems ENWW
178. ich you were sending a fax was busy The product automatically redials the busy number Recommended action Allow the product to retry sending the fax Call the recipient to ensure that the fax machine is on and ready Check that you are dialing the correct fax number Open the Service menu and touch the Fax Service button Touch the Run Fax Test button This test verifies that the phone cord is connected to the correct port and that the phone line has a signal The product prints a report with the results Fax receive error Description An error occurred while trying to receive a fax Recommended action Ask the sender to resend the fax Try faxing back to the sender or another fax machine Check that the telephone cord is securely connected by unplugging and replugging the cord Make sure that you are using the telephone cord that came with the product Open the Service menu and touch the Fax Service button Touch the Run Fax Test button This test verifies that the phone cord is connected to the correct port and that the phone line has a signal The product prints a report with the results Decrease the fax speed Ask the sender to resend the fax Turn off error correction mode Ask the sender to resend the fax NOTE Turning off error correction mode can reduce the quality of the fax image Connect the product to a different phone line 158 Chapter 6 Solve problems ENWW Fax Send error Description An error occurred
179. ick Run 2 Type TEMP in the Open field and then click OK 3 Double click the hppscan6 log file in the window that opens Selecting the third party destination option saves the scanned image in a file of the specified file type The HP Scan software then starts the specified software program by appending the filename after the software filename Because the HP Scan software does not support automatic discovery of software programs you must specify the correct software program and specify a file type that your program supports E mail The HP Scan software for Windows supports only 32 bit messaging application programming interface MAPI compliant e mail programs and does not support Internet based e mail programs such as Hotmail Yahoo or MSN The following table lists examples of supported e mail programs Table 2 6 Examples of supported e mail programs Program Name Windows OS Microsoft Outlook Yes Outlook 97 Outlook 98 Outlook 2003 Outlook XP Microsoft Outlook Express Yes Lotus Notes Yes V3 0 and later E mail is always sent through the default e mail client To see the default e mail client in Windows XP the path varies for other Windows operating system click Start click Settings click Control Panel click Network and Internet Options click Internet Options click the Programs tab and review the E mail setting Scan settings The following table shows the available scan settings 32 Chapter 2 Window
180. id Regular PS_24517 1TF Chicago Regular PS_24518 TTF Clarendon Light Regular PS_14513 1TF ClarendonPS Regular PS_10269 TTF ClarendonPS Bold PS_12968 TTF Cooper Black Regular PS_10369 TTF Cooper Black Italic PS_10370 TTF Copperplate32bc Regular PS_14514 TTF Copperplate33bc Regular PS_14515 1TF CoronetPS Italic PS_10249 TTF Eurostile Regular PS_10267 TTF Eurostile Bold Regular PS_10268 TTF Eurostile ExtendedTwo Bold PS_14512 TTF Eurostile ExtendedTwo Regular PS_14511 1TF Geneva Regular PS_24509 TTF GillSans Regular PS_13872 TTF GillSans Bold PS_13874 TTF Font support 41 42 Table 2 9 Additional PS emulation fonts continued Font name Font style File name GillSans Bold Italic PS_13875 TTF GillSans Condensed Regular PS_14053 TTF GillSans Condensed Bold PS_14054 TTF GillSans ExtraBold Regular PS_14051 TTF GillSans Italic PS_13873 TTF GillSans Light Italic PS_13871 TTF GillSans Light Regular PS_13870 TTF Goudy Bold PS_12544 TTF Goudy Bold Italic PS_10695 TTF Goudy Regular PS_12542 TTF Goudy ExtraBold Regular PS_12545 TTF Goudy Italic PS_12543 TTF Helvetica Condensed Regular PS_14526 TTF Helvetica Condensed Bold PS_14528 TTF Helvetica Condensed Bold Italic PS_14529 TTF Helvetica Condensed Italic PS_14527 TTF Hoefler Text Regular PS_24519 TTF Hoefler Text Black Regular PS_24521 TTF Hoefler Text Black Italic PS_24522 TTF Hoefler Text Italic PS_24520 TTF H
181. ied the configuration of the HP LaserJet Pro CM1410 Color MFP Series product since installation the driver can be automatically updated with the new configuration in environments that support bidirectional communication Use the Update Now feature to automatically reflect the new configuration in the driver For example if the product is installed and an optional paper handling accessory is added later use the Update Now feature to query the product and update the settings to match the new product configuration The feature automatically updates the registry and changes the configuration information that appears on the Device Settings tab NOTE Depending on which settings were updated the Update Now feature might change the configuration information that displays on the print driver tabs instead of or in addition to changing the information on the Device Settings tab NOTE The Update Now feature is not supported in environments where shared Windows XP clients are connected to Windows XP hosts To activate the Update Now feature follow these steps 1 In Windows Vista and Windows 7 click the Start button click Control Panel click Hardware and Sound and then click Printers In Windows XP Windows Server 2003 and Windows Server 2008 click Start click Settings and then click Printers and Faxes 2 Right click the product name 3 Click Properties 4 Click Device Settings 22 Chapter 2 Windows software descripti
182. ina E E el ypain Gro E E AEE E T S 28 HP Scan sohware anea r A la no E 29 Email siioni i E e dela Saeed 32 Scan SMM eerie ee r E E E E N 32 SCAM AVENS k e eer mene nner creer reer nee tree tet ret enere Sere tr rt reeeerore error tr rerr 33 WIA driven acssice scary oyaraid aera pieniiets ayaa E E EE a T E a oE 34 HP LaserJet Fax Setup UHI secerni ineine aa REE E Ra a EE E E A E e 35 HP LaserJet Send Fax software cx s sispicessinniessousnhitibwisitalnihailetanaivinbiniedlieaiinbiaiiauihailupetisetbeitdsn taslniiineii 36 Fax to multiple recipients ogo ness cine sass ansavineastn te saaiseeennanebadeioe taealuealiaualis telaahevasucunieaent 37 Credtesascover page ssicccidsendsdnesdolebexiysoccnntsdousedvesaniobentadea canteaeeeserqenniebons EEEREN 37 Fax pages scanned from the product document feeder ccccesccecesseeeeesteeeeeeseeeeeses 37 Fax without first printing and scanning the document sssccesereeeeteeeeeeeeeeneeesseeeeaees 37 Font SUPPO asee eree E a EE E EE ch nations T ee ees E E E 38 BOSI TONIS oa dca e a E E near 38 Detak fonts oieee eea arn eA age EEEa ETO 38 HP Driver Deployment Utility sss iceusscestsussqnsselihrsewnih sone iwc tseabacalp sates teat ain ih aiden blebs 44 3 Install Windows printing system components csccsecesccccsccsccsescecsccsseesseccsecsesessseesees 53 Install oN ind et er ee ke ae ear E et en a ee em ee ter 54 Software installation types for Windows 060 ccsscscesssenesece
183. includes HP ToolboxFX software HP ToolboxFX provides product status information such as toner and paper levels as well as pop up alert messages when the product requires attention You can also use HP ToolboxFX to configure the product settings HP Help and Learn Center The HP Help and Learn Center is installed with the recommended software set and provides access to product documentation and help To view the product documentation without installing the recommended software insert the CD ROM into the CD ROM drive When the installer screen appears click the documentation button on the left side of the screen Uninstaller The Uninstaller allows you to remove Windows HP printing system components See the Uninstaller section for instructions ll INSTALLATION INSTRUCTIONS The CD ROM setup or installation software detects the version and language of the operating system that you are running INSTALLING SOFTWARE NOTE Administrator privileges are required to install the printing system NOTE For USB installations DO NOT plug the USB cable into the computer and product until instructed to do so by the software The following methods are available for installing printer drivers and software components e Install Now This method installs the drivers and software Recommended for most users e Advanced Install Options Provides flexibility for installing your choice of drivers and software Recommended for advanced users and sy
184. ing order Paper sizes e Custom Paper Size e Paper source Paper type e Special pages Paper sizes The Paper sizes setting is a drop down menu that lists all of the supported paper sizes When you move the mouse over the dimensions label the mouse cursor changes from an arrow to a gloved hand Click the dimensions label to toggle between English and metric units Because paper size settings in most software programs override driver settings it is generally best to use the driver to set paper size only when you are printing from software programs that do not include a paper size setting such as NotePad or when you are producing a book or a booklet that does not require different paper sizes amp NOTE Certain software programs can override the size command and specify different paper sizes within a single document When you change the print driver setting to a paper size that is not currently loaded in the product a control panel message appears that prompts you to load the paper size or select another tray When the Settings under the Special Pages section have been changed the Paper sizes Paper source and Paper type menus change also offering a variety of options For more information see Special pages on page 74 Custom Paper Size The Custom Paper Size dialog box appears when you click Custom on the Paper Quality tab The following figure shows the initial appearance of the Custom Paper Size dial
185. ing specifies the source tray to use for printing a document The list of source trays depends on the accessories that are installed Any optional trays that are installed through the Device Settings tab also appear here Paper type The Paper type drop down menu shows all of the paper types that the HP LaserJet Pro CM1410 Color MFP Series supports Chapter separator pages Use the Chapter separator pages options fo designate where the first page of a chapter appears in the document The following are the Chapter separator pages options Chapters begin on pages Specify where in the document the chapters begin by designating a page number for each chapter Start each chapter Select Facing next page to make each chapter begin on the left side of the document Select Facing previous page to make each chapter begin on the right side of the document Document preview image The document preview image is a line drawn image of a page that represents graphics and text The document preview image is always oriented so that the contents of the page are right side up The document preview image appears in the upper right corner of the following Printing Preferences driver tabs Printing Shortcuts Paper Quality Effects Finishing Color Switching between tabs does not change the location or appearance of the document preview image When you move the mouse over the document preview image the mouse cursor changes from an arrow to a gloved han
186. installation Printer driver only Add Printer Windows Vista and Windows 7 1 Close all programs 2 Click Start click Control Panel and then click Hardware and Sound 3 Under the Printers or Devices and Printers section click Add a printer 4 Select Add Local Printer and either use an existing port or create a new port a For anew port select Standard TCP IP b Enter the IP Address or Host Name 5 Answer the questions in the Add Printer Wizard until you reach the screen that shows the printer manufacturer list 6 Click Have Disk 7 Browse to the printer driver location using one of the following options e CD ROM Browse to the DRIVERS OS PDL directory for your operating system on the software CD e Internet download Browse to the folder where the Web files were downloaded and decompressed 8 Select the appropriate INF file 9 Click Open and then click OK 10 Select the appropriate printer 11 Follow the remaining onscreen instructions to complete the printer installation ENWW Installation notes 249 UNINSTALLER The uninstall utility is available if the recommended or minimum software has been installed The Uninstaller removes the HP printing system software components 1 From the Start menu select All Programs and then click HP If you have more than one HP product choose the specific product and then click Uninstall from the program group 2 Follow the onscreen instructions to complete t
187. ion To ensure optimal print quality HP recommends replacing the print cartridge at this point You can continue printing until you notice a decrease in print quality Actual cartridge life may vary Once an HP supply has reached very low HP s premium Protection Warranty on that supply has ended All print defects or cartridge failures incurred when an HP supply is used in continue at very low mode will not be considered to be defects in materials or workmanship in the supply under the HP Print Cartridge Warranty Statement Device error press OK Description Generic engine error Recommended action This is a warning message only Job output might be affected If the error persists try the following solutions 1 Turn off then on 2 Perform an NVRAM initialization 3 Update the firmware 4 Replace the product Device is busy Try again later Description The product is currently in use Recommended action Wait for the product to finish the current job or to finish initializing Document feeder jam Clear and reload Description A piece of paper is jammed in the document feeder tray Recommended action Clear the jam If the error persists replace the document feeder pickup roller assembly 156 Chapter 6 Solve problems ENWW Document feeder mispick Reload Description The product did not pick up the paper in the document feeder Recommended action Remove the paper from the document feeder tray and then reload
188. ion at a different time when telephone line conditions have improved A fax T 30 trace report has information that can help resolve fax transmission problems If you call HP for help in resolving these problems print a T 30 trace report before you call 1 2 3 4 From the Home screen touch the Setup button Touch the Service menu Touch the Fax Service menu Fax logs and reports Print all fax reports ENWW Use the following instructions to print fax logs and reports Touch the Print T 30 Trace button and then touch the Now button Use this procedure to print all of the following reports at one time Last Call Report Fax Activity Log Phone Book Report Junk Fax List Billing Report when Billing Codes are turned on Configuration Report Usage Page Solve fax problems 217 1 From the Home screen touch the Fax button MO E 2 Touch the Fax Menu button 3 Touch the Fax Reports button 4 Touch the Print All fax Reports button 218 Chapter 6 Solve problems ENWW Print individual fax reports 1 From the Home screen touch the Fax button 2 Touch the Fax Menu button 3 Touch the Fax Reports button 4 Touch the name of the report that you want to print Set the fax error report A fax error report is a brief report that indicates the product experienced a fax job error You can set it to print after the following events e Every fax error the factory set default e Send fax
189. it the document into two portions corresponding to the ECM and non ECM portions Some products will attempt to use non ECM for photo mode so this may be associated with a between page encoding change to support photo mode ENWW Solve fax problems 209 Table 6 4 Fax receive error codes continued Error code 291 292 Description This is not a communication error and it is not expected that this error will occur under non development scenarios Reception has failed because the receiving product is unable to open a file to receive data into May be associated with low memory although low memory should be handle more gracefully than this The sending product has attempted to renegotiate the encoding mode from non JPEG to JPEG This operation is not supported and the session has been abandoned Solution If the error persists reinitialize the product Reattempt the fax reception and split the document into two portions corresponding to the JPEG and non JPEG portions Some products will attempt to use JPEG for photo mode so this may be associated with a between page encoding change to support photo mode Table 6 5 Fax send error codes Error code Description Solution 300 Fax session has completed without errors N A 311 The user of the receiving product has touched the Resend the fax Cancel X button causing the session to be prematurely halted before all pages have been transmitted 312
190. itialization resets the following settings and information e All menu settings are reset to factory default values e All localization settings including language and country region are reset A CAUTION All onboard network settings are also reset Be sure to print a configuration page before restoring defaults Make note of the IP address that is listed on the Jetdirect configuration page You might need to restore the IP address after an NVRAM initialization After performing an NVRAM initialization reconfigure any computers that print to this product Uninstall and then reinstall the product software on the computers 1 Turn the product off 2 Touch the right arrow button Hold this button as you turn the product on amp NOTE The right arrow button is not visible when the product is off but it is still active Note its position before you turn off the product 3 When Permanent storage init appears on the display release the right arrow button When the product has finished the NVRAM initialization it returns to the Ready state Solve fax problems Fax troubleshooting checklist e Several possible fixes are available After each recommended action retry faxing to see if the problem is resolved e For best results during fax problem solving make sure the line from the product is plugged directly into the wall phone port Disconnect all other devices that are connected to the product 1 Verify that the tel
191. ity 1 From the control panel Home screen touch the Setup N button 2 Open the Service menu and then open the Fax Service menu Touch the Run Fax Test button to test the fax functionality 3 Touch the Fax button on the product control panel and then touch the Start Fax button Step 7 Test the fax receiving functionality 1 From the control panel Home screen touch the Setup amp button 2 Open the Service menu and then open the Fax Service menu Touch the Run Fax Test button to test the fax functionality 3 Use another fax machine to send a fax to the product 4 If the product does not receive the fax make sure that you do not have too many telephone devices connected to the product and that all telephone devices are connected in the correct order 5 Review and reset the product fax settings 6 Turn off the Private Receive feature Step 8 Try sending a print job from a computer 1 Use a word processing program to send a print job to the product 2 If the job does not print make sure you selected the correct printer driver 3 Uninstall and then reinstall the product software ENWW Problem solving checklist 121 Step 9 Test the walk up USB printing functionality 1 Load a PDF document or JPEG photo onto a USB flash drive and insert it in the slot on the front of the product 2 On the control panel touch the USB Flash Drive button and try printing the document or photo 3 If no documents are listed
192. justments in the amount of each color of toner that is used for your printed documents e Contrasts Contrast is the range of difference between light highlight and dark shadow colors To increase the overall range between light and dark colors increase the Contrasts setting e Highlights Highlights are colors that are nearly white To darken highlight colors increase the Highlights setting This adjustment does not affect midtone or shadow colors e Midtones Midtones are colors that are halfway between white and solid density To darken midtone colors increase the Midtones setting This adjustment does not affect highlight or shadow colors e Shadows Shadows are colors that are nearly solid density To darken shadow colors increase the Shadows setting This adjustment does not affect highlight or midtone colors Paper Types Use these options to configure print modes that correspond to the various media types To reset all modes to factory default settings select Restore modes NOTE You must click Apply before your changes take effect 130 Chapter 6 Solve problems ENWW System setup Use the HP ToolboxFX system settings options to configure global settings for copy fax scan and print such as jam recovery and auto continue NOTE You must click Apply before the changes take effect Device polling You can turn off HP ToolboxFX device polling to reduce network traffic NOTE You must click Apply bef
193. k text only or edit an existing watermark The following watermarks are preset in the driver e none e Username e Confidential 80 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW e Draft e SAMPLE The Watermarks feature can be configured using the Driver Configuration Utility If the Username watermark is selected the driver will use the network username of the logged in user for the watermark The drop down menu shows alphabetically sorted watermarks that are currently available on the system plus the string none which indicates that no watermark is selected This is the default setting Any watermark that is selected from this list appears in the preview image When the First Page Only check box is selected the watermark is printed only on the first page of the document The First Page Only check box is disabled when the current watermark selection is none Watermarks are applied to logical pages For example when Pages per Sheet is set to 4 and First Page Only is turned off four watermarks appear on the physical page one on each logical page Click Edit and the Watermark Details dialog box appears The dialog box shows a preview image and provides options for creating a new watermark and controlling the message angle and font attributes Click OK to accept all of the changes that are made in the Watermark Details dialog box However clicking Cancel does not cancel a
194. k Tool 1 Open an Internet browser 2 Goto the following Web site www hp com go drivercheck Or use this alternative method 1 Open an Internet browser 2 Go to the HP Business Support Center BSC at the following Web site www hp com go bse 3 Click the self help resources link on the left navigation bar 4 Click automatic driver checker to run the HP Driver Diagnostic Printer Check Tool When the HP Driver Diagnostic Printer Check Tool runs the products that are currently installed on the computer appear in a list When you select the HP product that you would like to check the HP Driver Diagnostic Printer Check Tool gathers information about your product drivers and system setup in order to diagnose the software driver configuration and check the print driver The tool then verifies whether you are using the latest driver informs you if you are using an incorrect driver for the HP product and lets you know if an updated driver version is available for the product If an updated driver is available you can download and install the latest driver version by clicking it The data that the HP Driver Diagnostic Printer Check Tool gathers is stored anonymously so that HP can analyze and continuously improve its diagnostic tools No private data is gathered from the computer Chapter 2 Windows software description ENWW HP Customer Participation Program ENWW After the product is installed you have the option of parti
195. l and then click Scanner Wizard The WIA user interface is relatively simple and does not contain the wide range of image quality options that are available in the TWAIN driver user interface Figure 2 4 WlA driver user interface flatbed amp HP LaserJet CM1410 Series PCL 6 Scan What do you want to scan Paper source Flatbed v Select an option below for the type of picture you want to scan amer wi Black and white picture or text d Custom Settings You can also Adjust the quality of the scanned picture Preview Scan Cancel When you use the WIA scan driver you must modify the brightness and contrast after you perform the scan Contrast or brightness modifications cannot be set on the product Only native product resolutions are supported and no software interpolation is performed The WIA scan driver supports document 34 Chapter 2 Windows software description ENWW feeder or flatbed scanning but does not support duplex scanning The WIA scan driver supports the following file types e BMP e JPG e GIF e TIFF e FPX e PNG NOTE For more information about scanning see the HP LaserJet CM1410 MPP Series User Guide which is available on the printing system CD that came with the product HP LaserJet Fax Setup Utility ENWW The HP LaserJet Fax Setup Utility runs automatically after the printing system software is installed HP recommends that you run the utility to con
196. l Error Correction On The error correction mode allows the sending device to Off re transmit data if it detects an error signal Fax Service Log The fax service log prints out the last 40 entries in the fax log Cleaning Page USB Speed High Full Cleans the product when specks or other marks appear on printed output The cleaning process removes dust and excess toner from the paper path When selected the product prompts you to load plain Letter or A4 paper in Tray 1 Touch the OK button to begin the cleaning process Wait until the process completes Discard the page that prints Sets the USB speed for the USB connection to the computer For the product to actually operate at high speed it must have high speed enabled and be connected to an EHCI host controller that is also operating at high speed This menu item also does not reflect the current operating speed of the product 142 Chapter 6 Solve problems ENWW ENWW Menu item Less Paper Curl Archive Print Sub menu item On Off On Off Sub menu item Description When printed pages are consistently curled this option sets the product to a mode that reduces curl When printing pages that will be stored for a long time this option sets the product to a mode that reduces toner smearing and dusting Firmware Datecode Displays the current firmware datecode Restore Defaults Tools for trouble
197. l panel Each destination has a unique name and scan settings associated with it 30 Chapter 2 Windows software description ENWW Figure 2 3 Sean Setup Options dialog box HP LaserJet M1410 Series PCL 6 Scan Scan File Destination File Type PDF pdF Create a separate file for each scanned page File size quality Smallest size Best Quality OCR Set OCR language RTF Searchable PDF TXT English United States amp NOTE The Change the destinations that show up on the all in one control panel when I press the lt Scan To gt button option appears only if HP ToolboxFX is running Many of the dialog boxes in the HP Scan software contain the following four common buttons e Click Back to return to the previous dialog box e Click Next to go to the next dialog box e Click Cancel to cancel the creation or deletion of a scan destination e Click Help to gain access to context sensitive help for the dialog box The HP Scan software presents a series of dialog boxes that depend on the selections made in the HP Scan software dialog boxes ENWW Scan software 31 Every time the HP Scan software is used an HPPSCAN6 LOG file is generated in the current user s temporary directory The HPPSCAN6 LOG file appends after every scan and develops a log of operations that helps troubleshoot scanning problems To gain access to the log file follow these steps 1 Click Start and then cl
198. ler Installs the printing system software based on the hardware it detects from the host computer Uninstaller Removes files and folders that were installed when the printing system software was originally installed on the computer Scrubber Utility A standalone utility used remove all the installation files and folders that were installed with the printing system software was originally installed in the computer File to email Utility Collects crash logs and attaches the data files to an e mail to assist troubleshooting an installation or operation failure HP LaserJet Scan software Provides access to the scan functions on the product HP LaserJet Send Fax Provides the ability to send faxes from the computer software HP ToolboxFX Provides an interface to manage the product Use HP ToolboxFX to perform the following tasks e Monitor the status of the product e Change the print phone book and limited fax settings for the product e Find troubleshooting information and instructions for performing basic tasks e Receive Status Alerts when certain events occur or conditions exist on the product 16 Chapter 2 Windows software description ENWW Table 2 1 Software components for Windows continued Component Description Driver software Use the driver software to print fax and scan with the computer and the product This software includes the following drivers e The HP PCL 6 printer driver The HP PCL 6 printer driv
199. les are on the system and any user can connect the product to trigger the Plug and Play event NOTE The printer object is not created until the product is connected NOTE If you deploy multiple direct connect print drivers with preconfiguration and they all use a pre contig file with the same name the first one connected will be the only one configured properly This might happen if you deploy the PCL6 and PCL5 print drivers for the same product The reason is that the config file is copied to the 3 directory awaiting the product being connected Each deployment will just copy over the same config file since they all use the same name Once the product is connected this config file gets consumed and deleted Future Plug and Play events will not have the config file available How do I use the HP DDU to deploy a network product with preconfiguration NOTE Before running the HP DDU you must download the driver you want to package expand the driver and place the driver in its own directory on the computer where the HP DDU will run 1 2 Run HPDDU EXE to create the package From Package Source section a Select the print driver to package by browsing to the INF file in the directory Select the Pre configuration checkbox This checkbox is enabled only for print drivers that support preconfiguration c Select the Silently create network port and install driver install type d Click the Network Settings bu
200. letes e The product does not print and the computer has a third party firewall installed e The wireless connection does not work after moving the wireless router or product e Cannot connect more computers to the wireless product e The wireless product loses communication when connected to a VPN e The network does not appear in the wireless networks list e The wireless network is not functioning Wireless connectivity checklist e The product and the wireless router are turned on and have power Also make sure the wireless radio in the product is turned on e The service set identifier SSID is correct Print a configuration page to determine the SSID If you are not sure the SSID is correct run the wireless setup again e With secured networks make sure the security information is correct If the security information is incorrect run the wireless setup again e Ifthe wireless network is working correctly try accessing other computers on the wireless network If the network has Internet access try connecting to the Internet over a wireless connection e The encryption method AES or TKIP is the same for the product as it is for the wireless access point on networks using WPA security e The product is within the range of the wireless network For most networks the product must be within 30 m 100 ft of the wireless access point wireless router e Obstacles do not block the wireless signal Remove
201. ll of the changes If you make changes to a watermark and then select a different watermark or click New all of the changes are saved and only the current unsaved changes can be canceled Current watermarks ENWW The Current Watermarks group box contains a list of available watermarks both predefined watermarks that are available in the driver and any new watermarks that you have created To create a new watermark click New The new watermark appears in the Current Watermarks list and in the Watermark Message edit box as Untitled until you name it The name that you type in the Watermark Message field appears in the Current Watermarks group box in the Watermark Details dialog box and in the Watermarks group box on the Effects tab To name the new watermark type the selected watermark text in the Watermark Message edit box To delete a watermark select the watermark in the Current Watermarks list and then click Delete A warning appears asking whether you are sure you want to delete the selected item Click Cancel if you want to keep the watermark Click OK to delete the selected watermark NOTE You can have no more that 30 watermarks in the Current Watermarks list at one time When you reach the limit of 30 watermarks the New button is disabled To edit an existing watermark select the watermark in the Current Watermarks list If you change the Watermark Message for that watermark you are in effect creating a new waterma
202. llogical or impossible for the product to perform Sending a job with incompatible settings can lead to unexpected results If print jobs do not print as expected check the product documentation for the product capabilities In supported Windows operating environments some technically invalid print driver configurations result in warning messages Duplexing for example is not possible when the Transparency paper type is selected The following figure shows an Incompatible Print Settings message Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW ey NOTE ENWW Figure 4 1 An Incompatible Print Settings message HP LaserJet CM1410 Series PCL 6 Printing Preferences Advanced Printing Shortcuts Paper Quality Effects Finishing Color Services Paper Options Paper sizes 8 5 x 11 inches Letter Paper source Automatically Select v L Paper type l Color Laser Transparency v L Special pages Covers Print pages on different paper Settings Print Quality ImageREt 3600 To resolve the conflicting settings click Restore my previous settings and then click OK The driver resets the conflicting control back to its previous state If you want to keep the conflicting setting click Keep this setting and I will change it later and then click OK In this example the conflict can be resolved manual
203. lossless compression method Lossless means that no data is lost during compression o Maximum Compression Where applicable this option requires the software to always use a lossy compression method some data is lost e Alternative Letterhead Mode When selected this option eliminates the need to flip or reload letterhead or preprinted paper in a tray whether you are printing on one or both sides of the sheet Load the paper as you would for printing on both sides If the product tray has an icon that indicates whether to load paper either face up or face down load the paper in opposite orientation of that shown When this option is selected you must use one of the following options in the Paper type setting o Letterhead o Preprinted NOTE Because Alternative Letterhead Mode is available only if the product is equipped with an automatic duplexing unit the HP LaserJet Pro CM1415 and HP LaserJet Pro CM1415fn models do not support this option Layout Options The Layout Options setting contains the Page Order setting Page Order specifies the order in which the pages of your document are printed Front to Back prints the document so that page 1 prints first Back to Front prints the document so that page 1 prints last NOTE The page ordering operation works on whole sheets of paper rather than on individual logical pages Accordingly if you set Pages per Sheet on the Finishing tab to be greater than one the ord
204. lts restoring 203 Automatic Configuration fax setting 101 answer mode 136 cover page 37 data store parameters 244 continuous export feature 25 diagnostics 26 254 Index ENWW HP Driver Deployment Utility common problems 51 HP Driver Deployment Utility DDU 24 44 HP Driver Diagnostic Printer Check Tool 26 HP Driver Preconfiguration HP Driver Configuration Editor 24 HP Web Jetadmin Driver Configuration Plugin 24 OS and drivers supported 25 support guide 24 HP Jetdirect documentation 6 HP Jetdirect print server NVRAM initialization 204 HP LaserJet Send Fax program 36 HP LaserJet Utility Macintosh about 114 open 114 HP PCL 5 Universal Print Driver HP Driver Preconfiguration support 25 included 18 HP PCL 6 Print Driver features 61 HP Driver Preconfiguration support 25 included 18 settings 61 supported operating systems 18 HP PCL 6 printer driver media supported 244 mediatype commands 244 HP postscript level 3 emulation printer driver media supported 244 HP PS Universal Print Driver HP Driver Preconfiguration support 25 included 18 HP PS Universal Print Driver and PCL Universal Print Driver supported operating systems 18 HP Scan software 29 ENWW HP Toolbox FX Status tab 125 HP ToolboxFX about 125 density settings 130 Fax Setup Utility screen 35 Fax tab 126 features 16 Help tab 128 HP LaserJet Send Fax software 36 Network Settings tab 131 Print Settings tab 131 System Settings tab 129 HTM file
205. ly If the conflict is not resolved when the driver is closed then the same dialog appears again when a print job is sent to the product Help system 65 Advanced tab features NOTE The Advanced tab is located on the Printing Preferences tab set For information about how to access these tabs see Printing Preferences driver tabs on page 62 Use the Advanced tab to change the layout of printed pages Use this tab to configure special controls that are not commonly used as well as to control features such as collating and copies in the driver although most current software programs support these features in the print dialog box or through the page settings in the software program The following figure shows the Advanced tab Figure 4 2 The default appearance of the Advanced tab amp HP LaserJet CM1410 Series PCL 6 Copy 1 Printing Preferences Advanced Printing Shortcuts Paper Quality Effects Finishing Color Services G HP LaserJet CM1410 Series PCL 6 Advanced Document Settings E fag Paper Output E In Graphic a io Document Options advanced Printing Features RETEN E A Printer Features Print All Text as Black Disabled Send True Type as Bitmap Disabled Raster Compression Automatic Print Data Optimization Auto Layout Options Page Order Front to Back The Advanced tab contains the following controls e Paper Output e Graphic e Document Options Paper Output The
206. m third party or custom software programs e The best choice when operating with mixed environments which require the product to be set to PCL 5 UNIX Linux mainframe e Designed for use in corporate Windows environments to provide a single driver for use with multiple printer models e Preferred when printing to multiple printer models from a mobile Windows computer Download additional printer drivers from this Web site www hp com support CM 141 Oseries 188 Chapter 6 Solve problems ENWW Improve print quality for copies If you encounter print quality problems in copied documents review the solutions for printed documents listed previously in this document However some print quality problems occur only in copied documents e If streaks appear on copies made by using the document feeder clean the small glass strip on the left side of the scanner assembly e If dots or other defects appear on copies made by using the scanner glass clean the scanner glass and the white plastic backing 1 Use the power switch to turn off the product and then unplug the power cord from the electrical socket 2 Open the scanner lid 3 Clean the scanner glass and the white plastic backing with a soft cloth or sponge that has been moistened with nonabrasive glass cleaner A CAUTION Do not use abrasives acetone benzene ammonia ethyl alcohol or carbon tetrachloride on any part of the product these can damage the product Do not
207. mage drum 75 8 mm 2 98 in Image drum one rotation Appears in a single color plane and might be either a dark or white spot 633 6 mm 24 94 in ITB Because the ITB is longer than a page you might have to look at multiple pages to determine if repetitive defect is present Improve print quality 187 Use the printer driver that best meets your printing needs You might need to use a different printer driver if the printed page has unexpected lines in graphics missing text missing graphics incorrect formatting or substituted fonts HP PCL 6 driver e Provided as the default driver This driver is automatically installed unless you select a different one e Recommended for all Windows environments e Provides the overall best speed print quality and product feature support for most users e Developed to align with the Windows Graphic Device Interface GDI for the best speed in Windows environments e Might not be fully compatible with third party and custom software programs that are based on PCL 5 HP UPD PS driver e Recommended for printing with Adobe software programs or with other highly graphics intensive software programs e Provides support for printing from postscript emulation needs or for postscript flash font support HP UPD PCL 5 e Recommended for general office printing in Windows environments e Compatible with previous PCL versions and older HP LaserJet products e The best choice for printing fro
208. me The product might not have enough memory for some jobs Fit to Page on flatbed only Description The copy reduce enlarge feature called Fit to Page applies only to copies made from the flatbed scanner ENWW Tools for troubleshooting 159 Recommended action Use the flatbed or select another reduction enlargement setting Install color cartridge Description One of the color cartridges is not installed with the door closed Recommended action Install the indicated color cartridge If the error persists replace the print cartridge drawer Invalid driver Press OK Description You are using the incorrect printer driver Recommended action Select the printer driver that is appropriate for your product Invalid entry Description Invalid data or response Recommended action Correct the entry Jam in area Open door and clear jam Description There is a paper jam in the print paper path or output bin Recommended action Clear the jam from the area indicated on the product control panel and then follow the control panel instructions Remove any debris from the paper path Jam in Tray 1 Clear jam and then press OK 160 Description The product has detected a jam in Tray 1 Recommended action Clear the jam and then follow the control panel instructions Chapter 6 Solve problems ENWW Load paper Description The tray is empty Recommended action If paper is already loaded in the tray tes
209. menus on the various menus 2 Click Options amp Supplies 3 On the Presets menu click Save as and type a name for the preset 3 Click the Driver menu These settings are saved in the Presets 4 Select the driver from the list and menu To use the new settings you must configure the installed options select the saved preset option every time you open a program and print Software for Macintosh computers HP LaserJet Utility Use the HP LaserJet Utility to set up product features that are not available in the printer driver You can use the HP LaserJet Utility when the product uses a universal serial bus USB cable or is connected to a TCP IP based network Open the HP LaserJet Utility Open the HP Printer Utility in Mac OS X v10 5 and v10 6 1 In System Preferences click the Printer amp Fax icon 2 Select the printer and then click the Open Print Queue button 3 Click the Utility icon Embedded Web Server The product is equipped with the HP Embedded Web Server HP EWS which provides access to information about device and network activities For a complete explanation of the features and functionality of the HP EWS see the product user guide which is available on the printing system software CD Availability This STR provides information about the availability of the printing system software and related software and firmware Printing system software on a CD is available from HP fulfillment centers
210. nal reports faxes or any print job that does not specify a size NOTE The default setting is determined by the choice of location during the initial product setup Sets the type for printing internal reports faxes or any print job that does not specify a type Configures the size and type for the tray Paper Out Action Print Quality Color Calibration Wait forever Cancel Override Calibrate Now Power On Calibration Determines how the product reacts when a print job requires a paper size or type that is unavailable or when the tray is empty e Wait forever The product waits until you load the correct paper e Override Print on a different size paper after a specified delay e Cancel Automatically cancel the print job after a specified delay e Ifyou select either the Override or Cancel item the control panel prompts you for the number of seconds to delay Performs a full calibration e Calibrate Now Performs an immediate calibration e Power On Calibration Specify the length of time the product should wait after you turn it on before it calibrates Volume Settings Alarm Volume Ring Volume Key Press Volume Phone Line Volume Set the volume levels for the product The following options are available for each volume setting e Off e Soft e Medium e Loud ENWW Tools for troubleshooting 139 Menu item Sub menu item Sub menu item Description PowerSave Time Sleep D
211. nddianntea waite Sedagatancesatd cuebaaahedaddvaes 88 Eyentlog messag S ainoana e a enn Ree eu a 168 Repetitive image defects sai ci dxduaaiceesiedderanainedaitnhed nedaiwneaiuvtinaianieeaddaeudt nedieuiemnvacheledaiinndssaabennaawubbaledas 187 Secondary service Menu cirsaacddnensaradanenecducnss heuienensh Matdhianbaraseenatedonsxasneuasituahashedunctintaaesae 202 Fax receive error codes aicise i er teeter n Ea EE A haan nea EEES 206 KEEN KE C 210 HP LaserJet Pro CM1410 Color MFP Series MFP Series media sources and destinations 243 Media so rcecommandS sorserien onthe a aN 243 Mediatype commands cui Sondasatserenuensimeinecnas teraseicnedaieerssacinnatadanaqeuatnava nnani heini 244 xvi ENWW List of figures Figure 1 1 Installation software CD User Documentation screen ccsscceeseecsreeeereeeeteeeeeeeeneecnseesertetseeneats 4 Figure 1 2 Installation software CD Administrator Documentation screen cccseceeeereeeetseeenseeeeteeeeseeensaees 6 Figure 2 1 Welcome to the HP Product Survey Program screen 00cccccccccceeeeteeeeeeteeeeeeeeeees 27 Figure 2 2 HP Scan dialog box 4 iciisdccnaicinnaponvareasieait tecnatedont Gra rstiraluahawatniniiteedcnuobieiacatsatechia tana taleniateen etek Goan 30 Figure 2 3 Sean Setup Options dialog box 2 2 0 ccc cceeeceeeeeeeeseeeeeeeeeeeeeeeseeeeeseeeseseseeeseiseeenenseeees 31 Figure 2 4 WlA driver user interface flatbed eecceseseeeeseeenseeenceee
212. ne shneenniod eae beateiavenddieueiiniaeedewnidanenaieanes 238 Print ready file printing by using FTP through a browser s cccsesceeeeteeeeeeseeeesnneeeeees 238 Print ready file printing by using FTP on a direct network connection cccceeeteeereeees 239 Windows operating SyStetNe aivariideraavenslerwsccvsassiaride dana raneve ter aaetnanttiites 239 Macintosh operating systems a ciczsesswixracnuytarnorstonnesantqnstannnernbnaneanie 240 Print ready printing by using a local Windows port cccssereceesereeeeeeeesteeenaeeeeees 240 Windows 2000 Service Pack 3 Windows XP Windows Server 2003 Windows Server 2008 or Windows Vista cssesccecccueeseccceenseescceaeauees 241 Print ready file printing in a Windows network ccccescceeeeeteeeeeneeeeeneeeeseteeeenteeeees 241 Print ready file printing in UNIX systems ccscceeeseeesereeeeeeeenseeeenseeeenseeeenreesnaeeeeeas 241 Print ready file printing by using the LPR command cccccccceeeeeceeeeeesteeeeeseenseeeeees 241 Paper a d print media giz getty taste been tera ea terns tehip a talencaist asic direanean niai erener rea e tena 243 Media sources and destinations in jipcrsunat anton masala 243 Source command S irinse E a a e E E R 243 Mediatype S nce alt cpnaeadhcetasauancnceane net E E EA E 244 Media type commands d ismrneetunnmennneneuee ea leaatiamwers 244 Parameter settings fax data store parameters ccccccccesseceeeeeceeeeeeneeeeeese
213. nline help that is included with each software component SUPPORTED OPERATING SYSTEMS The CD that ships with your product includes software for the following operating systems Windows XP 32 bit Service Pack 2 and higher Windows Vista 32 bit and 64 bit Windows 7 32 bit and 64 bit Windows Server 2003 32 bit Service Pack 3 Windows Server 2008 32 bit and 64 bit The following operating systems support the recommended software components Windows XP 32 bit Service Pack 2 and higher Windows Vista 32 bit and 64 bit Windows 7 32 bit and 64 bit The recommended software includes the following components ENWW HP LaserJet Help and Learn Center HP ToolboxFX HP LaserJet PCL 6 print driver HP Web Registration HP Scan Application multifunction products only HP LaserJet Send Fax Application multifunction products only Installation notes 245 e HP LaserJet Fax Setup Utility multifunction products only e HP LaserJet Fax Driver multifunction products only NOTE The minimum software may be installed instead of the recommended by choosing Click here for more install options on the Software to Install screen The following operating systems support only the minimum software components e Windows Server 2003 32 bit Service Pack 3 e Windows Server 2008 32 bit and 64 bit The minimum software includes the following components e HP LaserJet PCL 6 print driver e HP Scan Application multifunction products
214. nstalled setting on the Allow manual duplexing option on the Device Settings tab Cardstock paper can be manually printed on the second side but no change occurs to the print mode Transparencies and labels should never be manually printed on the second side To print a multiple page document follow these steps 1 Select the Print on Both Sides Manually check box 2 Click OK The even number pages of the document print 3 When the control panel shows the Manually Feed message insert the stack of paper on which the even number pages have been printed as indicated in the following figure ENWW Finishing tab features 87 Figure 4 6 Print on Both Sides Instructions dialog box Print on Both Sides Instructions After the even numbered pages have printed a message will appear on the printer s display instructing you where to load the paper Follow the instructions below to print the odd numbered pages second sides Without changing the 2 Maintaining the same 3 If printing does not orientation remove the orientation insert the paper automatically continue paper stack from the stack into Tray 1 printed side press the Go or Select Output Bin Do not discard down button blank sheets When you have completed the steps that appear in the dialog box the second half of the print job prints on the back side of the stack of paper The driver does not require the program to specifically support odd and even page printing because t
215. nvelope Monarch Envelope B5 Envelope C5 Envelope DL Unspecified default Plain HP LaserJet 90g ENWW ENWW HP Color Laser Matte 105g HP Premium Choice Matte 120g HP Color Laser Brochure Matte 160g HP Superior Laser Matte 160g HP Cover Matte 200g HP Matte Photo 200g HP Tri fold Color Laser Brochure 160g HP Superior Laser Glossy 160g HP Color Laser Photo Glossy 220g HP Color Laser Photo Glossy 220g faster printing HP Color Laser Photo Glossy 220g higher gloss Light 60 74g Mid Weight 96 110g Mid Weight Glossy 96 110g Card Glossy 176 220g Color Laser Transparency Labels Letterhead Envelope Heavy Envelope Preprinted Prepunched Colored Bond Recycled Rough Heavy Rough HP Tough Paper Printing Shortcuts tab features 105 Print on both sides NOTE Because the HP LaserJet Pro CM1415 and HP LaserJet Pro CM1415fn models do not include a duplexing unit the Print on both sides option is available but duplexing is a manual process The following options are available e No default e Yes Flip Over e Yes Flip Up Eco print Two sided Printing e Paper source Automatically Select e Paper sizes Letter e Paper type Unspecified e Print on both sides Yes flip over Factory Defaults When Factory Defaults is selected the customizable options are grayed out locking in those default options The Factory Defaults are as follows e Paper source Automatically select e P
216. o select individual entries from the phone book instead of importing the entire phone book To delete all entries click Delete All and then click Yes In addition to numerical digits the following are valid characters for fax numbers r lt space gt Tools for troubleshooting 127 Fax send log The HP ToolboxFX fax send log lists all recently sent faxes and information about them including the date and time sent job number fax number page count and the results Click any column heading in the fax send log to re sort the information in that column in ascending or descending order The Results column provides the fax status If the fax attempt was unsuccessful this column provides a description of why the fax was not sent Fax receive log The HP ToolboxFX fax receive log provides a list of all recently received faxes and information about them including the date and time received job number fax number page count results and an abbreviated fax image The fax receive log can be used to block future faxes Check the Block Fax box next to a received fax listed on the log Click on any column heading in the fax receive log to re sort the information in that column in ascending or descending order The Results column provides the fax status If the fax attempt was unsuccessful this column provides a description of why the fax was not received NOTE You must click Apply before the changes take ef
217. oefler Text Ornaments Regular PS_24523 TTF Joanna MT Regular PS_14503 TTF Joanna MT Bold PS_14505 TTF Joanna MT Bold Italic PS_14506 TTF Joanna MT Italic PS_14504 TTF Letter Gothic Italic PS_13778 TTF Letter GothicPS Regular PS_13777 11F Letter GothicPS Bold PS_13779 11F Letter GothicPS Bold Italic PS_13780 TTF Lubalin Graph Regular PS_12675 T1F Lubalin Graph Bold PS_12677 1TF Lubalin Graph Bold Italic PS_12625 TTF Chapter 2 Windows software description ENWW Table 2 9 Additional PS emulation fonts continued Font name Font style File name Lubalin Graph Italic PS_12623 1TF MarigoldPS Regular PS_94073 TTF Mona Lisa Recut Regular PS_14525 1TF Monaco Regular PS_24524 TTF New York Regular PS_24510 TTF Optima Regular PS_12506 TTF Optima Bold PS_12510 1TF Optima Bold Italic PS_12511 TTF Optima Italic PS_12507 TTF Oxford Italic PS_14072 1TF StempelGaramond Roman Italic PS_11546 TTF StempelGaramond Roman Regular PS_11545 TTF StempelGaramond Roman Bold PS_11547 TTF StempelGaramond Roman Bold Italic PS_11548 TTF Taffy Regular PS_14507 1TF Univers 45 Light Regular PS_13501 TTF Univers 45 Light Bold PS_14023 TTF Univers 45 Light Bold Italic PS_14024 TTF Univers 45 Light Italic PS_13502 TTF Univers 47 CondensedLight Bold PS_14030 TTF Univers 47 CondensedLight Bold Italic PS_14040 TTF Univers 55 Regular PS_14021 1TF Univers 55 Italic PS_14022 TTF Univers 57 Condensed Regular
218. oes not appear again and no data will be gathered HP Customer Participation Program 27 Scan software Scan methods HP Scan software Scan drivers Scan methods Scan from the product by using any of the following methods From the product control panel On the product control panel touch the Scan button Use the arrow buttons to select an option and then touch the Scan button to start the scan NOTE Scanning from the product control panel is possible only after the option has been configured in the HP Scan software The following options are configured by default for a USB connection o If you select File the scanned photo will be saved to a directory that you specify e If you select OCR the scanned document will be opened in the Readiris software to convert into an editable text document NOTE This option only appears if Readiris text recognition software is installed on the computer For more information see the help on the Readiris CD o If you select EMAIL PIC the scanned photo will be attached to a new e mail message You can then add an e mail address add notes and send the message o If you select EMAIL DOC the scanned document will be attached to a new e mail message You can then add an e mail address add notes and send the message o Ifyou select SETUP the HP Scan software opens the Sean Setup Options dialog box where you can create change or delete the destination options that are
219. of the page are rightside up The document preview image appears in the upper right corner of the following Printing Preferences driver tabs e Printing Shortcuts e Paper Quality e Effects e Finishing e Color Switching between tabs does not change the location or appearance of the document preview image When you move the mouse over the document preview image the mouse cursor changes from an arrow to a gloved hand You can toggle between portrait and landscape page orientation by clicking the image Color tab features 95 Services tab features 96 NOTE The Services tab is located on the Printing Preferences tab set For information about how to access these tabs see Printing Preferences driver tabs on page 62 The Services tab is shown in the following figure Figure 4 8 Services tab amp HP LaserJet CM1410 Series PCL 6 Copy 1 Printing Preferences Advanced Printing Shortcuts Paper Quality Effects Finishing Color Services Internet Services Select a destination Includes troubleshooting manuals etc The Services tab contains the following group boxes e Internet Services Device services Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW Internet Services The Internet Services group box contains the Select a destination drop down menu with the following selections e Online diagnostic tools This is the HP Ins
220. og box NOTE The HP LaserJet Pro CM1410 Color MFP Series product supports custom paper sizes up to 14 inches in length To use this paper size set the custom paper size to match the custom paper size that you are using up to 14 inches in length Name Use the Name text box to type a new name for a custom paper size When you change the name to something other than Custom the Save and OK buttons become active ENWW Paper Quallity tab features 71 The name that appears in the Name text box depends on the following conditions e f a saved custom paper size has been selected from the drop down menu on the Paper Quality tab then the Name text box shows the name of the selected custom paper size e Ifa standard paper size has been selected on the Paper Quality tab then the Name text box shows the default name of Custom e Ifa new name has been typed into the Name text box for the purpose of saving a new size or renaming an existing size then that new name will remain in the text box until the new size is saved or the dialog box is closed If you type a new name into the Name text box but then do not click Save you can change the width and height values without losing the name However if you close the dialog box without clicking Save any unsaved name or size values are lost without warning Paper size The width and height values can be changed by typing numeric strings into the edit boxes in the Paper Size group box
221. olored shadows blurry graphics or areas that have poor color you might need to calibrate the product to align the colors Print the Diagnostics Page from the Reports menu on the control panel to check the color alignment If the blocks of color on that page are not aligned with each other you need to calibrate the product 1 On the product control panel open the System Setup menu 2 Open the Print Quality menu and select the Color Calibration item 3 Select the Calibrate Now option Check the print cartridges Check each print cartridge and replace it if necessary if you are having any of the following problems e The printing is too light or seems faded in areas e Printed pages have small unprinted areas e Printed pages have streaks or bands E NOTE If you are using a draft print setting the printing might appear light If you determine that you need to replace a print cartridge print the Supplies Status Page to find the part number for the correct genuine HP print cartridge Type of print cartridge Steps to resolve the problem Refilled or remanufactured print Hewlett Packard Company cannot recommend the use of non HP supplies either cartridge new or remanufactured Because they are not HP products HP cannot influence their design or control their quality If you are using a refilled or remanufactured print cartridge and are not satisfied with the print quality replace the cartridge with a genuine HP c
222. on The receiving fax line did not answer The product attempts to redial after a few minutes Recommended action Allow the product to retry sending the fax Call the recipient to ensure that the fax machine is on and ready Check that you are dialing the correct fax number If the product continues to redial unplug the product telephone cord from the wall plug in a telephone and try making a voice call Open the Service menu and touch the Fax Service button Touch the Run Fax Test button This test verifies that the phone cord is connected to the correct port and that the phone line has a signal The product prints a report with the results No fax detected Description The product answered the incoming call but did not detect that a fax machine was calling Recommended action Allow the product to retry receiving the fax Open the Service menu and touch the Fax Service button Touch the Run Fax Test button This test verifies that the phone cord is connected to the correct port and that the phone line has a signal The product prints a report with the results 164 Chapter 6 Solve problems ENWW Print failure press OK If error repeats turn off then on Description The product could not print the current page because of its complexity Recommended action Touch the OK button to clear the message Replace color Description The print cartridge is at the end of its useful life and the At Very Low menu item in the System
223. on ENWW 5 If necessary click Installable Options to expand it and show the options 6 In the Automatic Configuration drop down menu select Update Now 7 Click OK to save the setting HP Driver Configuration HP Driver Configuration is a software architecture and set of tools that permits HP printing system software to be customized and distributed in managed corporate printing environments Using HP Driver Configuration information technology IT administrators in corporate and enterprise environments can preconfigure the printing and device defaults for HP print drivers before installing the drivers in the network environment HP Driver Configuration is most beneficial when configuring print drivers for multiple workstations or print servers for print queues that share the same configuration Two types of features can be configured e device settings e _ printing preferences settings The driver is configured to match the product hardware so that access to all of the product accessories through the driver is enabled correctly for example for duplexing units and additional input trays Most driver feature settings can also be configured HP Driver Configuration configures the driver to match the accessories that are installed on the product or to match the settings that IT administrators make in the configuration CFG file for example optional trays total amount of memory job storage settings or mopier settings The con
224. on about how to access the Printing Preferences tab set see Printing Preferences driver tabs on page 62 2 Click to select Booklet Printing NOTE Typically you select the size of each page of the booklet in your software program by clicking File clicking Page and then clicking Setup If your software program does not allow you to set the paper size use the Paper sizes drop down menu on the Printing Shortcuts tab 3 Select the appropriate settings from the following drop down menus on the Printing Shortcuts tab e Paper type e Paper source e Orientation e Booklet Layout 4 Click OK to print ENWW Finishing tab features 89 Pages per Sheet Use the Pages per Sheet option to select the number of pages that you want to print on a single sheet of paper If you choose to print more than one page per sheet the pages appear smaller and are arranged on the sheet in the order that they would otherwise be printed The Pages per Sheet drop down menu provides six settings e 1 page per sheet this is the default e 2 pages per sheet e 4 pages per sheet e 6 pages per sheet e 9 pages per sheet e 16 pages per sheet NOTE When you select an option other than 2 pages per sheet booklet printing is unavailable R Related controls indented beneath Pages per Sheet are Print Page Borders and Page Order which become active when Pages per Sheet is greater than 1 Print Page Borders Print Page Borders sets a
225. onds used by the sending product and it has terminated the session 1 If the document was large ask the sender to retransmit the document as two or more smaller documents 2 Disable ECM and reattempt the fax reception 247 251 252 253 The sending product appears fo be stuck on Telephone line conditions were too poor to receive a fax The sending product has attempted to initiate a page transmission using a page width that is not supported by the receiving product N A 1 Reattempt the fax reception at a later time when line conditions may have improved 2 Configure the receiving product to start reception at a lower speed 3 If the receiving product received successfully several pages of a larger document ask the sender to transmit the document in several smaller parts Ask the sender fo reconfigure the fax product to transmit using a normal letter A4 page width Chapter 6 Solve problems ENWW Table 6 4 Fax receive error codes continued Error code Description Solution 281 The receiving product has not received any data at the start of a page during non ECM reception although the modem has not detected a sending disconnect The sending product is probably transmitting fill bytes instead of data and has either jammed or broken 282 The receiving product has not received any data at the start of a page during ECM reception although the modem has not detected a
226. one Book Add edit or delete entries in the product phone book Fax Send Log View all of the recent faxes that have been sent from the product Fax Receive Log View all of the recent faxes that have been received by the product Block Faxes Add delete or view fax numbers that are blocked The following options are available when receiving a fax Print the fax You can also select an option to have a message appear on your computer to notifying you when the fax was printed Forward the fax to another fax machine NOTE You must click Apply before the changes take effect Fax phone book Use the HP ToolboxFX fax phone book to add and remove individuals or groups on your speed dial list import phone books from a variety of sources and update and maintain the contact list To add an individual contact to the speed dial list select the row of the speed dial number that you want to specify Type the contact name in the Contact name window Type the fax number in the Fax number window Click Add To add a group of contacts to the speed dial list select the row of the speed dial number that you want to specify Click Add Group Double click a contact name from the list on the left to move it to the group list on the right or select a name on the left and then click the appropriate arrow to move it to the group list on the right You can also use those two methods to move names from right to left When you have created a group
227. ontinued Error code Description Solution 392 The receiving product has answered a fax session 1 Reattempt the fax reception at a different time and completed the initial V 34 handshake but has when telephone line conditions have been to detect any T30 frames This failure is either improved a compatibility problems with certain products or is due to line conditions 2 Disable V 34 on the receiving product and attempt the transmission using the V 17 393 The receiving product has failed to complete the mode third phase of the initial V 34 handshake after answering a fax session This is usually due to poor line conditions although it may be a compatibility issue with certain products and or line conditions 394 The receiving product has failed to successfully negotiate the initial V 8 handshake with the sending product after answering a fax session Typically this will occur when the calling product is not fax capable It may also be a compatibility issue with certain products and or line conditions 395 An unexpected T 30 frame has been received 1 Reattempt the fax reception If transmission between pages during a multipage V 34 errors are not encountered because line reception This is almost certainly a compatibility conditions have improved then this error will problem with the sending product and may be due probably be avoided to an error with the implementation of the sending 2 Disable V 34 on the receiving product an
228. or 51 2100 Cyan scanner laser error 51 2200 Magenta scanner laser error 51 2300 Yellow scanner laser error 54 0600 Density sensor error 54 1200 Black density measurement abnormality 54 1201 Cyan density measurement abnormality 54 1202 Magenta density measurement abnormality 54 1203 Yellow density measurement abnormality 54 1400 Color plane registration sensor error 54 1599 Black CPR pattern can t be read 54 1501 Cyan CPR pattern can t be read 54 1502 Magenta CPR pattern can t be read 54 1503 Yellow CPR pattern can t be read 54 1500 Yellow toner level sensor error 54 1600 Magenta toner level sensor error Chapter 6 Solve problems ENWW Table 6 1 Event log messages continued Event code Description 54 1700 Cyan toner level sensor error 54 1800 Black toner level sensor error 54 1900 Bad top of page TOP sensor 54 2100 Beam detect BD error 55 0000 Engine internal communication error 55 0601 DC controller NVRAM data error 55 0602 DC controller NVRAM access error 55 1000 DC controller memory error 59 0160 ITB or main motor rotation error 59 A0 59 0192 Developer motor rotation error 59 CO 59 0240 Transfer alienation failure 59 FO 59 3000 Fuser motor startup error 59 4000 Fuser motor error 59 5000 Image drum motor startup error black 59 5300 Image drum motor startup error yellow 59 6000 Image drum motor rotation error black 59 6300 Image drum motor rotation error
229. ore the changes take effect Print Settings The HP ToolboxFX Print Settings tab contains links to the following main pages e Printing Change the default product print settings such as number of copies and paper orientation e PCLS View and change the PCL5 settings e PostScript View and change the PS settings Printing Use these options to configure the settings for all print functions These are the same options that are available on the control panel NOTE You must click Apply before your changes take effect PCL5 Use these options to configure the settings when you are using the PCL print personality amp NOTE You must click Apply before your changes take effect PostScript Use this option when you are using the PostScript print personality When the Print PostScript error option is turned on the PostScript error page automatically prints when PostScript errors occur NOTE You must click Apply before your changes take effect Network Settings The network administrator can use this tab to control the network related settings for the product when it is connected to an IP based network NOTE You cannot configure wireless network settings by using the HP ToolboxFX software ENWW Tools for troubleshooting 131 Internal print quality test pages Configuration page The configuration page lists current product settings and properties This page also contains a status log report 1
230. ot sent cccccccseeecccuesccecueccccauccecaesceceuevess 224 Unable to use fax functions from the control panel ccccececeeeeteeeeeeteeees 224 Unable to use speed dials nstinvncentrnancdegatenioinirtan iceman eueoiereeuans 225 Unable to use group dials scar ceipusesarviae Mond tanveedine nd eanteds avetmateoeiuetsts 225 Receive a recorded error message from the phone company when trying to senda fat a Let doh C rape leat ndteande asad aa n e le Aten hecatnnl 225 Unable to send a fax when a phone is connected to the product 5 226 Solve problems receiving faxes 55 2s se adecvtieeatesdeusgs ol Cueva a boca dasuns dare Grd oe oaadouite 227 The fax does not respond ssiscsaacceissvsects ssh teapaae ceeded Gactvoctaeeteatinn eieveds 227 The fax has a dedicated phone line ccceeeceeeesseeeeetteeeeeees 227 An answering machine is connected to the product 60000 227 xii ENWW A telephone handset is connected to the product csseeeeteees 228 The Answer Mode setting is set to the Manual setting 00 228 Voice mail is available on the fax line cceeceeeeeesteeeetteeeeeees 228 The product is connected to a DSL phone service ccceeeeeees 229 The product uses a fax over IP or VoIP phone service 0000e 229 An error message displays on the control panel ccceeesceeeeestteeeeeeeaes 229 The No fax detected message appears ececeeseessee
231. page only The Effects tab contains the following controls e Resizing Options Document preview image e Watermarks 78 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW Resizing Options The Resizing Options group box consists of the following controls e Actual Size default e Print Document On e Scale to Fit e of Actual Size Actual Size Actual Size is the default setting It prints the document without changing the document size Print Document On Click the Print Document On option to format the document for one paper size and then print the document on a different paper size with or without scaling the image to fit the new paper size The Print Document On control is disabled by either of the following conditions e The of Actual Size value is not 100 e The Pages per Sheet value on the Finishing tab is not 1 When Print Document On is selected the drop down menu shows the paper sizes on which you can print The list contains all of the standard paper sizes that the selected paper source supports and any custom sizes that you have created When Print Document On is selected Scale to Fit is automatically selected Clear this check box if you do not want your document reduced or enlarged to fit on the selected paper Scale to Fit The Seale to Fit option box specifies whether each formatted document page image is scaled to fit the target paper size By default
232. path gt where lt path gt is the location where the print ready file was downloaded from the Web For example type the following put username desktop P3010FW PDF NOTE If the file name or path includes a space you must enclose the file name or path in quotation marks For example type put user name desktop P3010FW PDF To ensure that the entire path to the print ready file is placed in the put command type put and a space and then click and drag the printready file onto the terminal window The complete path to the file is automatically placed after the put command Press Enter The download process begins and the firmware is updated on the product This can take about five minutes Let the process finish without further interaction with the product or computer The product automatically turns off and on again to activate the update Print ready printing by using a local Windows port To print directly by using a local Windows port follow the instructions for your operating system 240 Chapter 7 Engineering Details ENWW Windows 2000 Service Pack 3 Windows XP Windows Server 2003 Windows Server 2008 or Windows Vista The printready file can be sent directly to the product by typing a copy command at a command prompt or in an MS DOS window 1 At a command prompt type copy b lt FILENAME gt lt PORTNAME gt where lt FILENAME gt is the name of the print ready file including the path and lt PORTNAME gt is
233. pear in the Font s to be Added window Select the fonts that you want to add and then click Add The fonts are installed and the file names appear in the Installed Font s window Click OK to close the HP Font Installer dialog box Removing external fonts 1 So ee eS UP 8 In Windows Vista and Windows 7 click the Start button click Control Panel click Hardware and Sound and then click Printers In Windows XP Windows Server 2003 and Windows Server 2008 click Start click Settings and then click Printers and Faxes Right click the name of the product Click Properties Click the Device Settings tab Click the External Fonts option The Properties button appears Click Properties The HP Font Installer dialog box appears The external fonts that are installed appear in the Installed Fonts window Select the fonts that you want to remove and then click Remove The fonts are removed Click OK to close the HP Font Installer dialog box Installable Options Items under Installable Options are automatically populated and their defaults set when the driver is installed 100 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW The HP LaserJet Pro CM1410 Color MFP Series product has printing options that you can install and configure in this section The following controls are available e Automatic Configuration e Allow Manual Duplexing e Job Separator Automatic Configur
234. phone handset is connected to the product Set the Answer Mode option to the Automatic setting ES From the Home screen touch the Setup button Open the Fax Setup menu 2 3 Open the Basic Setup menu 4 Open the Answer Mode menu 5 Select the Automatic setting The Answer Mode setting is set to the Manual setting e Touch the Start Fax button on the control panel Voice mail is available on the fax line e Add a distinctive ring service to your telephone line and change the Distinctive Ring setting on the product to match the ring pattern supplied by the telephone company Contact your telephone company for information Verify that the answer mode is set to the Automatic setting b From the Home screen touch the Setup N button c Open the Fax Setup menu d Open the Basic Setup menu 228 Chapter 6 Solve problems ENWW e Open the Distinctive Ring menu f Select the correct setting e Buy a dedicated line for faxing e Set the Answer Mode option to the Manual setting a From the Home screen touch the Setup amp button Open the Fax Setup menu c Open the Basic Setup menu d Open the Answer Mode menu e Select the Manual setting E NOTE You must be present to receive faxes The product is connected to a DSL phone service e Check the installation and features A DSL modem requires a high pass filter on the phone line connection to the product Contact your DSL service provider for a filter or
235. product setup From the Home screen touch the Setup button Open the Fax Setup menu c Open the Basic Setup menu d Open the Answer Mode menu e Select the setting that matches the product setup Set the Answer Mode option to the Fax Te setting to automatically receive faxes The Fax Tel setting automatically detects whether the incoming transmission is a fax or a voice call and routes the call to the appropriate device A phone line splitter is being used e If you are using a phone line splitter remove the splitter and set up the phone as a downstream phone e Make sure the phone is hung up e Make sure the phone is not being used for a voice call when faxing No dial tone e If using a phone line splitter remove the phone line splitter and set up the phone as a downstream phone Cannot send or receive a fax on a PBX line e If you are using a PBX phone line contact your PBX administrator to configure an analog fax line for your product 232 Chapter 6 Solve problems ENWW Solve general fax problems e Faxes are sending slowly e Fax quality is poor e Fax cuts off or prints on two pages Faxes are sending slowly The product is experiencing poor phone line quality e Retry sending the fax when the line conditions have improved e Check with the phone service provider that the line supports fax e Turn off the Error Correction setting a Open the Setup menu Open the Service menu c Open the Fax
236. product telephone cord from the wall plug in a telephone and try making a call Plug the product phone cord into a jack for another phone line e Try a different phone cord e From the control panel change the Fax Speed option to the Medium V 1 7 setting or Slow V 29 setting a From the Home screen touch the Setup N button b Open the Fax Setup menu Chapter 6 Solve problems ENWW No dial tone c Open the Advanced Setup menu d Open the Fax Speed menu e Select the correct setting Turn off the Error Correction option a From the Home screen touch the Setup amp button b Open the Service menu c Open the Fax Service menu d Open the Error Correction menu e Select the Off setting NOTE Turning off the Error Correction option can reduce image quality If the error persists contact HP See www hp com support CM 141 Oseries or the support flyer that came in the product box Make sure that the telephone cord is plugged into the correct port on the product Make sure that the telephone cord from the product is plugged directly into the wall telephone jack Check for a dial tone on the phone line by using the Start Fax button Unplug the product telephone cord from the wall plug in a telephone and try making a voice call Unplug the telephone cord from both the product and the wall and replug the cord Make sure that you are using the telephone cord that came with the product Plug the
237. r You can assign a form which defines the paper size and margins to each paper source When a form is matched to a source you can select the form when you print The product prints from the tray to which that form is assigned Network administrators can use the Form to Tray Assignment setting to specify in the driver the paper size that is loaded into each available input tray The use of forms constrains the choices that are available in the paper size list on the Paper Quality tab in the Printing Preferences driver tabs This constraint prevents or reduces the likelihood of tying up the product with paper mount messages that occur when users request sizes or types that are not available The trays listed in the Form to Tray Assignment setting include standard trays and optional accessory trays Generally items that are installed separately have a separate Installable Options setting The input trays listed here are also listed as paper sources on the Paper Quality tab Configuring the trays 1 Select the appropriate tray in the Form to Tray Assignment list 2 Use the drop down menu to select the paper size or form that is loaded in that tray 3 Repeat steps 1 and 2 for the remaining trays 4 Click OK to enable your settings or if necessary click Caneel to reconfigure all the trays and remove the size and type constraints that have been imposed on the Paper Quality tab Font Substitution Table Use the Font Substitution Ta
238. r the original ENWW Tools for troubleshooting 145 146 Menu item Sub menu item Sub menu item Description Paper Paper Size Specifies the paper size and type Paper Type NOTE The default paper size setting is determined by the choice of location during the initial product setup The default paper type setting is plain Multi Page Copy Off When this feature is on the product prompts you to load On another page onto the scanner glass or to indicate that the job is complete Collation On Specifies whether to collate copy jobs Off Draft Mode off Specifies whether to use draft quality printing for copies On Image Adjustment Lightness Adjusts the image quality settings for copies Contrast Sharpen Background Removal Color Balance Grayness Set as New Defaults Restore Defaults Saves any changes you have made to this menu as the new defaults Restores the factory defaults for this menu Fax Menu To open this menu touch the Fax button and then touch the Fax Menu button Menu item Fax Reports Sub menu item Fax Confirmation Sub menu item On Every Fax On Send Fax Only On Receive Fax Only Never Description Sets whether the product prints a confirmation report after a successful fax job Chapter 6 Solve problems Menu item Sub menu item Sub menu item Description Include First Page On Sets whether the product includes a thumbnail image Off of the
239. r 6 Solve problems ENWW 3 Clean the scanner glass and the white plastic backing with a soft cloth or sponge that has been moistened with nonabrasive glass cleaner A CAUTION Do not use abrasives acetone benzene ammonia ethyl alcohol or carbon tetrachloride on any part of the product these can damage the product Do not place liquids directly on the glass or platen They might seep and damage the product 4 Dry the glass and white plastic backing with a chamois or a cellulose sponge to prevent spotting 5 Plug in the product and then use the power switch to turn on the product Clean the document feeder pickup rollers and separation pad If the product document feeder experiences paper handling problems such as jams or multiple page feeds clean the document feeder rollers and separation pad 1 Open the document feeder cover A ENWW Clean the product 191 2 Use a moist lint free cloth to wipe both pickup rollers and the separation pad to remove dirt ae 3 Close the document feeder cover b Clean the touch screen Clean the touch screen whenever it is necessary to remove fingerprints or dust Wipe the touch screen gently with a clean water dampened lint free cloth A CAUTION Use water only Solvents or cleaners can damage the touch screen Do not pour or spray water directly onto the touch screen 192 Chapter 6 Solve problems ENWW The product does not print or it prints slowly T
240. r LASERJET PRO CM1410 COLOR MFP SERIES Software Technical Reference r HP LaserJet Pro CM1410 Color MFP Series Software Technical Reference Copyright and license 2010 Copyright Hewlett Packard Development Company L P Reproduction adaptation or translation without prior written permission is prohibited except as allowed under the copyright laws The information contained herein is subject to change without notice The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein Edition 1 9 2010 Trademark Credits Adobe Acrobat and PostScript are trademarks of Adobe Systems Incorporated Corel is a trademark or registered trademark of Corel Corporation or Corel Corporation Limited Microsoft Windows Windows 7 Windows Vista and Windows XP are U S registered trademarks of Microsoft Corporation UNIX is a registered trademark of The Open Group ENERGY STAR and the ENERGY STAR mark are registered U S marks Table of contents 1 Document ond product basics siccicss cisco oe 1 PU OGG and Scope sisisi iniinis tared enina vi delaras tain aea aa a Ea aaan e aN aia aani 2 Documentation availability and localization cisssaccevas
241. r and use the remaining toner in the print cartridge past very low follow these steps 1 On the product control panel touch the Setup N button and then touch the System Setup button 2 Touch the At Very Low button and then touch the Color Cartridges button Touch the Continue button 140 Chapter 6 Solve problems ENWW ENWW Menu item Sub menu item Sub menu item Description When you choose to replace the very low print cartridge color printing resumes automatically User Defined Low Black Type the percentage of estimated life remaining at which the product alerts you that the print cartridge is low Cyan Magenta Yellow USB Flash Drive On Enables or disables the USB flash drive Off Color Copy On Enables or disables color copying Off Courier Font Regular Sets Courier font values Dark Tools for troubleshooting 141 Service menu In the following table items that have an asterisk indicate the factory default setting Menu item Fax Service Sub menu item Sub menu item Clear Saved Faxes Run Fax Test Description Clears all faxes in memory Performs a fax test to verify that the phone cord is plugged in the correct outlet and that there is a signal on the phone line A fax test report is printed indicating the results Print T 30 Trace Now Prints or schedules a report that is used to troubleshoot fax Never transmission issues If Error At End of Cal
242. references tabs Printing Shortcuts tab features 107 3 On the Printing Shortcuts tab click Save As The Printing Shortcuts dialog box appears 4 Type a name for the custom printing shortcut and then click OK The custom printing shortcut appears in the Printing Shortcuts list 5 To delete a custom printing shortcut click the custom shortcut then click the Delete button 108 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW About tab features NOTE The About tab is located on the Properties tab set For information about how to access these tabs see Properties driver tabs on page 63 The About tab provides detailed information about driver component versions It contains an overall build version number in parentheses after the model name together with specific information about each of the components The information varies according to the HP LaserJet Pro CM1410 Color MFP Series model number driver date and versions The About tab is shown in the following figure Figure 4 11 About tab amp HP LaserJet CM1410 Series PCL 6 Copy 1 Properties dg General Sharing Ports Advanced Color Management Security Device Settings About HP LaserJet CM1410 Series PELE 61 94 41 4 c Copyright 1996 2009 Hewlett Packard Development Company L P Driver Files a UNIDRY DLL 0 3 7600 16385 HPMDPO94 DLL 0 3 1542 133 _UNIDRV HLP 3 4 2010 amp Configuration Status
243. rely halted 222 The receiving product has answered a call buthas 1 Confirm that the sender is a fax product and been unable to detect the presence of a calling fax p g product for one of the following reasons e Typically this will be due to the receiving fax product answering a voice call e The sender canceled the fax transmission by touching the Cancel X button immediately prior to or just as the receiving product answered the call e The sending product automatically ended the call immediately prior to or just as the receiving product answered the call e The sending sending fax product determined there was a feature incompatibility between the two and disconnected immediately before transmitting any further fax tones or T 30 frames This is very rare not a voice caller typically you must rely on the sender informing the caller that the fax session is failing 2 Ifthe sending product ends the call just as the receiving product starts reception reduce the ring count after which the receiving product answers Alternatively suggest that the sender manually dials to the receiving product and then manually starts the fax session by touching theStart Fax button once fax tones have been heard from the receiving product 3 Confirm that the sender is not inadvertently attempting to poll transmit from the receiving product instead of transmitting to the receiving product 4 Reconfigure the receiving fax product
244. rensnsssenncersestnsaceentedanssuncenstseaunnese 54 Installat om OpHONS sirrien enai a EEEE EEEE ORE AEDA ES AREAREN ERT 54 General Windows installation instructions idissscsssesunsacerevdanennatssniesansabohiarstdusehassdontseoauboaseaniiebanlin 55 General Windows installation for direct connections cccccccceeeeeceeeeeeeteeeeeeeeetseeees 55 Windows installation instructions for direct connected USB products 55 Printer driver only installation instructions Microsoft Add Printer Wizard 55 General Windows installation for network connections ccccccccceceeseeeeeeeeseeeeeeteeees 57 Network Seth pinci e ae meee 57 Windows installation instructions for network connected products 00 57 Printer driver only installation instructions Microsoft Add Printer Wizard 58 Printer sharing disclaimer sises ssiserinasei iiaia a inii 59 Point and Print installation for Windows ccccccccceeeeeeseeeeceseeeeeeeeeseeeeeeeeeeeeeeettseeeeees 59 Modify a pre existing installation ssiaipnuscenesacivanseooeantonind spaneniemnausctued manaronameeuns 60 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ssssssssssssossssossssosse 61 ISAS acre ets cast a E E E E en ant naamNaeON eee hare 61 Access print driver saniser kinse ii date Are i eE i e e ae e S SNS 62 Printing Preferences driver tabs si lt saantsianssansewrdsrmniuoasennsralasivensansssncinseannenasparhiueieveadbaanne
245. res that are available over a network connection except for the Receive faxes to this computer feature which can only be enabled for one computer General Windows installation instructions 57 Use the following instructions to install the printing system software on a computer that is running Win 7 Windows XP or Windows Vista and is connected to the product through a network NOTE You must have administrator privileges to install the software 1 Quit all open programs 2 Insert the printing system software CD into the CD ROM drive NOTE Ifthe CD ROM does not start automatically click Start click Run and then browse to and double click the SETUP EXE file in the root directory of the CD 3 Click the appropriate installation type and follow the onscreen prompts 4 When the installer software prompts you to select how the product will be connected select Connect through a wired network Follow the onscreen prompts 5 If you are prompted to restart the computer click Yes 6 After installation of the printing system software a test page prints and dialog boxes appear that allow you to register the product over the Web and set up faxing Printer driver only installation instructions Microsoft Add Printer Wizard NOTE This printer driver only software solution provides print only functionality through a communications port that has already been created for this product USB or network connected
246. resolution images have fewer dots per inch and show less detail but the file size is smaller and the fax Superfine takes less ti akes less time to transmit Photo Lighter Darker Sets the darkness of outgoing faxes Fit to Page On Shrinks incoming faxes that are larger than the paper size set for the tray Off Glass Size Letter Sets the default paper size for documents being scanned from the flatbed scanner A4 NOTE The default setting is determined by the choice of location during the initial product setup Dialing Mode Tone Sets whether the product should use tone or pulse dialing Pulse Redial if Busy On Sets whether the product should attempt to redial if the line is busy Off Redial if No Answer On Sets whether the product should attempt to redial if the recipient fax number does not answer Off Redial if Comm On Sets whether the product should attempt fo redial the Error recipient fax number if a communication error occurs Off Tools for troubleshooting 137 Menu item Sub menu item Sub menu item Description Detect Dial Tone On Sets whether the product should check for a dial tone before sending a fax Off Billing Codes On Enables the use of billing codes when set to On A prompt appears where you can enter the billing code for an Off outgoing fax Extension Phone On When this feature is enabled you can press the 1 2 3 buttons on the extension phone to cause the product to Off answer an incoming fax
247. rget Use the Save as button to enter the name and location for the output package by browsing or typing it in The utility will create the package in the temp directory and then move it to the final location Create Package Click the Create Package button when you have entered all the above information This button will be disabled until you have entered the required information Once it is clicked the Cancel button and Progress bar will be enabled To stop the package creation click the Cancel button The executable file runs silently unless a user prompt is requested for a direct connect product If an error is encountered during execution an error dialog will appear To suppress the error dialog select the Suppress all end user error messages check box If you selected the Pre configure this driver checkbox the print driver configuration dialog will open when you click the Create Package button Once you have configured the print driver select OK to save the new configuration settings and continue creating the package Clicking Cancel will cancel the entire package creation process 48 Chapter 2 Windows software description ENWW Figure 2 8 HP DDU Driver Configuration settings Driver Configuration Configure the driver settings before installation Printing Preferences Device Settings Print on Both Sides Duplex False Orientation Portrait Print in Grayscale Disable Print Quality 600 dpi EconoMode False Paper
248. rints pages that have preprinted lines for writing music Landscape Tools for troubleshooting 135 Fax Setup menu 136 In the following table items that have an asterisk indicate the factory default setting Menu item Sub menu item Fax Set Up Utility Sub menu item Description This is a tool for configuring the fax settings Follow the on screen prompts and select the appropriate response for each question Basic Setup Time Date Settings for time format current time date format and current date Sets the time and date setting for the product Fax Header Enter your fax number Enter company name Sets the identifying information that is sent to the receiving product Identifies the fax sender optional Answer Mode Rings to Answer Automatic Manual TAM Fax Tel Sets the type of answer mode The following options are available e Automatic The product automatically answers an incoming call on the configured number of rings e Manual The user must press the Start Fax button or use an extension phone to make the product answer the incoming call e TAM A telephone answering machine TAM is attached to the Auxilary phone port of the product The product will not pick up any incoming call but only listen for fax tones after the answering machine has picked up the call e Fax Tel The product must automatically pick up the call and determine if the call i
249. rk Effects tab features 81 Watermark Message The Watermark Message is also the name that identifies the watermark in the Current Watermarks list except when more than one watermark has the same message For example you might want several different watermarks with the message DRAFT each with a different typeface or font size When this occurs the string is appended with a space a pound sign and a number for example Draft 2 When a number is added the number two is used first but if the resulting name is also in the list then the number increases until the name is unique Draft 3 Draft 4 and so on Message Angle Use the controls in the Message Angle group box to print the watermark in different orientations on the page All settings center the watermark string within the page the selection of a particular setting affects only the angle of the string placement The following settings are available e Diagonal This is the default setting Select this setting to place the text along a line that spans the lower left to upper right corners of the page e Horizontal Select this setting to place the text along a line that spans the mid left and mid right edges of the page e Custom Select this setting to place the text at the specified angle across the page Use the numeric spin box to select the angle Font Attributes Use the controls in the Font Attributes group box to change the font and the shading size and style of
250. rk Name Arial Varies by language Color Gray Gray Shading Very Light Very Light Effects tab features 83 84 Table 4 1 Font Attribute settings for new and preset watermarks continued Setting New watermark Preset watermark Size 80 Varies by language Style Regular Regular Click OK to accept all of the changes that have been made in the Watermark Details dialog box Clicking Cancel does not cancel all of the changes If you make changes to a watermark and then select a different watermark or click New all of the changes are saved and only the current unsaved changes can be canceled Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW Finishing tab features NOTE The Finishing tab is located on the Printing Preferences tab set For information about how to access these tabs see Printing Preferences driver tabs on page 62 Use the Finishing tab to print booklets and control the paper output The following figure shows the Finishing tab Figure 4 5 Finishing tab amp HP LaserJet M1410 Series PCL 6 Copy 1 Printing Preferences Advanced Printing Shortcuts Paper Quality Effects Finishing Color Services Document Options Print on both sides manually C Flip pages up Booklet layout Off Pages per sheet 1 page per sheet Print page borders Page ord Right then Down Orientation Portrait O Landscape C Rotate by 180 degrees
251. roduct firmware You can adjust the Neutral Grays setting independently for text graphics or photographs The following options are available e Black Only This option generates neutral colors grays and black by using only black toner This option guarantees that neutral colors do not have a color cast Black Only is the default setting for the Text and Graphics components e 4 Color This option generates neutral colors by combining all four colors of toner which produces smoother gradients and transitions to non neutral colors It also produces the darkest possible black 4 Color is the default setting for Photographs Color Themes The Color Themes group box contains the following RGB color options which determines how colors are rendered e Default sRGB e Photo sRGB e Photo Adobe RGB 1998 e Vivid sRGB e None Default SRGB Select Default SRGB for most printing needs This setting instructs the product to interpret RGB color as sRGB which is the accepted standard of Microsoft and the World Wide Web Consortium W3C Colors are matched to optimize the RGB colors on the screen and to provide vivid images and graphics Photo SRGB Select Photo SRGB to enhance documents in which the content is mainly bitmap images such as GIF or eps files This setting instructs the product to use the best color matching for rendering sRGB bitmap images This setting affects only raster data it has no effect on text or v
252. rough the installation process Software installation types for Windows The following printing system software installation types are available e Select the recommended software default e Select the minimum software Selecting Click here for more install options allows you to choose between the installation types and allows you to view the software components that are installed with each installation type The installer guides the installation whether you are configuring a direct connected or a network connected product The installer additionally detects hardware and network connections and helps guide the installation For example if the installer detects an HP LaserJet Pro CM1410 Color MFP Series it automatically configures the software connection to that product This saves several steps If the installer detects fax capabilities or a network it also guides setting up those features Installation options 54 The HP LaserJet Pro CM1410 Color MFP Series printing system software can be installed when the product is connected to the computer in the following configurations e on a computer that is directly connected to the product through a USB port Directly connected via a USB port e Connected via a wired or wireless network Chapter 3 Install Windows printing system components ENWW General Windows installation instructions e General Windows installation for direct connections e General Windows installation for net
253. rt V LEGAL STATEMENTS TRADEMARK NOTICES Adobe Acrobat and Adobe PostScript 3 are trademarks of Adobe Systems Incorporated ENERGY STAR and the ENERGY STAR mark are registered U S marks Microsoft Windows Windows XP and Windows Vista are U S registered trademarks of Microsoft Corporation UNIX is a registered trademark of the Open Group SOFTWARE WARRANTY LICENSE AND COPYRIGHT Warranty See the user guide for complete warranty and support information License See the user guide for complete information about HP software license terms Copyright 2010 Copyright Hewlett Packard Development Company L P Reproduction adaptation or translation without prior written permission is prohibited except as allowed under the copyright laws ENWW Installation notes 251 The information contained herein is subject to change without notice The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein 252 Chapter 7 Engineering Details ENWW Index Symbols Numerics 2ndary service menu 202 A accessories automatic configuration 20 administrator documentation 5 Adobe Acrobat Reader printing PDF files without 238 viewing documentation 3 advanced setup fa
254. s viewing 3 l ICM See Image Color Management Image Color Management color graphics printing 67 enabling 67 image quality HP ToolboxFX settings 130 repetitive image defects 187 Incompatible Print Settings messages See constraint messages information pages configuration page 132 initialization NVRAM 204 input trays See trays install notes 5 installation component languages 12 Macintosh printing system software 116 options 54 Point and Print 59 pre existing modifying 60 system requirements for Macintosh 112 troubleshooting Macintosh 117 Windows printing system software 54 J jams causes of 171 document feeder clearing 173 locating 172 output bin clearing 178 trays clearing 175 Jetdirect Guide 6 Jetdirect print server NVRAM initialization 204 L languages CD 9 driver 11 installer component 12 LEDs troubleshooting 123 local port command line printing Windows 240 localized CD 9 location setting 202 lockable features drivers 25 logs fax error 219 printing all 217 Lotus Notes 32 LPR commands printing PDF files 241 M Macintosh hardware requirements 112 Macintosh operating systems CD ROM 115 driver settings 114 HP LaserJet Utility 114 installing printing system software 116 removing software 118 software 114 software components 112 supported versions 112 Macintosh OS direct printing 238 troubleshooting setup 117 manuals See documentation media See paper Index 255 memory included
255. s Finishing tab 85 document preview image 76 80 90 95 Effects tab content 78 Factory Defaults setting Printing Shortcuts tab 106 Finishing tab contents 85 Flip Pages Up setting Finishing tab 88 Font Substitution Table settings Device Settings tab 99 Form to Tray Assignment setting Device Settings tab 98 General Everyday Printing setting Printing Shortcuts tab 103 Graphic setting Advanced tab 67 Help system 64 ICM options Advanced tab 67 incompatible print settings messages 64 installable options Device Settings tab 100 Internet Services options Services tab 97 Job Separator setting Device Settings tab 101 Layout Options setting Advanced tab 69 Manual settings Color tab 93 Neutral Grays settings Color tab 94 Orientation settings Finishing tab 91 Page Order settings Finishing tab 90 Pages per Sheet setting Finishing tab 90 Paper Options settings Paper Quality tab 70 ENWW Paper source setting Paper Quality tab 72 Paper type setting Paper Quality tab 73 Paper Output settings Advanced tab 66 Paper Quality tab contents 70 Print All Text as Black setting Advanced tab 68 Print on Both Sides settings Finishing tab 86 Print Optimizations setting Advanced tab 68 Print Quality settings Paper Quality tab 76 Printer Features setting Advanced tab 68 Printing Preferences tab driver access 62 Printing Shortcuts tab contents 102 Properties tab driver access 63 Raster
256. s 112 uninstalling Macintosh 118 software CD Windows 7 solve fax problems 220 solve problems fax 233 solving direct connect problems 196 network problems 196 walk up USB printing problems 195 sources paper See trays Special Pages covers 75 status alerts HP Toolbox FX 125 viewing with HP Toolbox FX 125 Status tab HP Toolbox FX 125 supplies status viewing with HP Toolbox FX 125 supplies status page printing 184 System Settings tab 129 System setup menu 139 T text files command line printing 238 touch screen clean 192 trays Alternative Letterhead Mode 69 included 243 jams clearing 175 media source commands 243 media type commands 244 settings 130 specify paper size 98 troubleshoot diagnostics 96 HP driver Diagnostic Printer Check Tool 26 troubleshooting checklist 120 control panel messages 151 control panel diagnostics 124 direct connect problems 196 fax error correction setting 219 faxes 204 jams 171 LED diagnostics 123 Macintosh setup 117 network problems 196 NVRAM initialization 204 paper feed problems 171 receive fax 227 receiving faxes 206 send fax 220 sending faxes 210 walk up USB printing problems 195 ENWW TWAIN driver 17 TXT files command line printing 238 types media HP ToolboxFX settings 130 types paper commands 244 U uninstall Macintosh software 118 UNIX OS direct printing 241 print ready printing 241 Update Now feature steps to activa
257. s also provided in this STR Additional detailed information about the printing system software is published in an addendum to this STR The following information is available in the addendum e _ Lists of installed files e System modification information such as files added or modified Chapter 1 Document and product basics ENWW Documentation availability and localization NOTE For information about language support for the HP LaserJet Pro CM1410 Color MFP Series ENWW product see CD versions and language support on page 9 The following table lists the availability of HP LaserJet Pro CM1410 Color MFP Series printing system documentation by operating system Table 1 1 Documentation availability Document Windows XP Server Macintosh 2003 Server 2008 Vista 7 HP LaserJet Pro CM1410 Color MFP Series User Guide PDF file x x HP LaserJet Pro CM1410 Color MFP Series Install Notes x Access to HP LaserJet documents depends on the type of document and its location e Some documents can be opened from the Installer e Some documents are available on the Web through links in the Installer Documents are available in the following file formats e Portable Document Format PDF The HP LaserJet Pro CM1410 Color MFP Series printing system software CD includes Adobe Acrobat Reader for viewing online documentation e Compiled HTML CHM When you click a documentation link to a CHM document a Microsoft HTML
258. s 62 Propertiesdriver fabs acresannaien nnn aE E a E ann 63 Help syslen eE E A E A E A EE E 64 Whats this Hel presaneniei nreno E e EE a 64 Incompatible Print Settings messages ivscsascsnssseversecnerersveniavsacesieddvevedsuvbbeasvesatdanuntiietbes 64 Advanced tab features ica cisiviriistensainja dvastasneibeirtedletinea ated jusinoauaindceltaltedidieaalajasiontalanoneonbaiaiteaieanitadiens 66 iv ENWW PE SiO E T teats ayy G5 x icv as very Maes oi eon oh aa en 66 Copy Count i s eneee a a sates e eaaa ea a eee ti 67 ETE E E AEE A uaa iwolghes aU RRA TNS 67 Image Color Management siciuiiise darian ey dtihue otitis ir taddeus 67 True Type FONTS teaccnavavisvaasetsedecsag tate hdeesemdated N 67 Document Options aie sia sate hueh A veces A A Aged aia ation a levees 68 Advanced Printing Features burs Sev cancer rncecadutadyarevaaratnudeubaa nde eeae tu cuundvetialins 68 Print OptimiZations scccseccceede ccacecsnsacivassieecavacacsescscacess ae stanedsvaedeasadevaaseas 68 Primer REGIURES rangi tus Seu ecg a S cateseneicn gadis E A tment late 68 layout Options petet E E cane E lana naan hes Geatsed Meow AE 69 Paper Quality tab features swayed weiss autor oe event en RR Ee 70 Paper OPtions sseicastsiasegeresingonrvebessveanvoeend a aa To o Sobis Goan ETOT A E Saeed 70 Paper Sizes re n a E a E E O E E a BE 71 Custom Paper Size itn een eaten Pe ae a en 71 N To aae AAE E EA T E 71 PODER Size a a a a a a 72 Units eseina tvnin nn A e EA EE
259. s RGB color as if it were printed as a photograph using a digital mini lab The product renders deeper more saturated colors differently than with the Default sRBG theme Use this theme when printing photos Photo Adobe RGB 1998 Use this theme with printing digital photos that use the AdobeRGB color space rather than sRGB Turn off color management in the software program when using this theme None Change the color options Change the color options settings for the current print job from the color tab of the printer driver 1 On the File menu in the software program click Print 2 Click Properties or Preferences 3 Click the Color tab 180 Chapter 6 Solve problems ENWW ENWW 4 Click the Automatic or Manual setting 5 e Automatic setting Select this setting for most color print jobs e Manual setting Select this setting to adjust the color settings independent from other settings NOTE Changing color settings manually can impact output HP recommends that only color graphics experts change these settings TARGET NOT FOUND Click the Print in Grayscale option to print a color document in black and white Use this option to print color documents for photocopying or faxing 6 Click the OK button Improve print quality 181 Use paper that meets HP specifications Use different paper if you are having any of the following problems e The printing is too light or seems faded in areas e
260. s a voice or fax call If the call is a fax call the product handles the call as usual If the call is a voice call an audible synthesized ring is generated to alert the user of an incoming voice call Sets the number of rings that must occur before the fax modem answers The default setting is 5 Chapter 6 Solve problems ENWW Menu item Sub menu item Distinctive Ring Sub menu item All Rings Single Double Triple Double and Triple Description If you have distinctive ring phone service use this item to configure how the product responds to incoming calls e All Rings The product answers any calls that come through the telephone line e Single The product answers any calls that produce a single ring pattern e Double The product answers any calls that produce a double ring pattern e Triple The product answers any calls that produce a triple ring pattern e Double and Triple The product answers any calls that produce a double ring or triple ring pattern Dial Prefix On Specifies a prefix number that must be dialed when sending faxes from the product If you turn this feature on the Off product prompts you to enter the number and then it automatically includes that number every time you send a fax Advanced Setup Fax Resolution Standard Sets the resolution for sent documents Higher resolution images have more dots per inch dpi so they show more Fine detail Lower
261. s error appears on the control panel The scanner motor is obstructed Scanner reserved for PC scan Description A computer is using the product to create a scan Recommended action Wait until the computer scan has finished or cancel the scan from the computer software or touch the Cancel X button Scanning error Cannot connect Description The product cannot transmit scan information to a computer Recommended action Verify that the connection cable is not loose or damaged Replace the cable if necessary and try the scan again Settings cleared Description The product has cleared job settings Recommended action Re enter any appropriate job settings Used color installed to accept press OK Description A used color printer cartridge has been installed or moved Recommended action Touch the OK button to return to the Ready state Yellow Cartridge Low Description The print cartridge is nearing the end of its useful life 166 Chapter 6 Solve problems ENWW Recommended action Printing can continue but consider having a replacement supply on hand Yellow in wrong position Description The print cartridge is installed in the incorrect slot Recommended action Make sure that each print cartridge is installed in the correct slot From front to back the print cartridges are installed in this order black cyan magenta and yellow Yellow Very Low Description The print cartridge is at the end of its useful life
262. s slowly Solve walk up USB printing problems Solve connectivity problems Solve wireless network problems Service mode functions Solve fax problems Product updates 119 Problem solving checklist Follow these steps when trying to solve a problem with the product 6 Step 1 Check that the product power is on Step 2 Check the environment where the product is installed Step 3 Check the control panel for error messages Step 4 Test print functionality Step 5 Test copy functionality Step 6 Test the fax sending functionality Step 7 Test the fax receiving functionality Step 8 Try sending a print job from a computer Step 9 Test the walk up USB printing functionality Check that the product power is on Make sure the product is plugged in and turned on Make sure the power cable is connected to the product and the outlet Check the power source by connecting the power cable to a different outlet If the product motors do not rotate make sure the print cartridges are installed and that the doors are all closed The control panel displays messages to indicate these problems If the document feeder motor does not rotate open the document feeder cover and remove any packing material or shipping tape If the scanner bulb does not light during copying scanning or faxing contact HP support Step 2 Check the environment where the product is installed Is the product install
263. s software description ENWW Table 2 7 Available scan settings Option Resolution NOTE Scanning at higher resolution requires longer scan times and more memory Scan settings 75 dpi 100 dpi 150 dpi 200 dpi 300 dpi 600 dpi 1200 dpi Image type bit depth Black and White 1 bit Grayscale 8 bit Color 24 bit File type Portable Network Graphics png Adobe PDF pdf Searchable PDF pdf JPEG ipg ipeg GIF gif Windows Bitmap bmp TIFF tiff tif Rich Text rtf Text txt Size to scan Entire Scan Area Letter 8 5 x 11 inches Legal 8 5 x 14 inches Document Feeder Only A4 210 x 297 mm 3 5 x 5 in 9 x 13 cm 4x 6in 10 x 15 cm 5 x 7 in 13 x 18 cm 8 x 10 in 20 x 25 cm Custom Scan Size Scan drivers e WlAdriver Scan software 33 WIA driver E NOTE The WIA driver does not support duplex scanning Use any of the following methods to open the Windows Image Acquisition WIA scanning feature for Windows XP Start WIA scanning through a WIA compliant software program Right click on the scanner icon in the My Computer folder and then click Sean Right click on the scanner icon in the My Computer folder and then click Scanner Wizard Right click on the scanner icon in the Scanners and Cameras folder in the Control Panel and then click Sean Right click on the scanner icon in the Scanners and Cameras folder in the Control Pane
264. sc amp n Wdpapertype where n is the number of characters in the paper type plus 1 For example in the sequence Esc amp n6 WdPlain Plain has 5 letters plus 1 for a total of 6 Table 7 3 Media type commands Esc amp n Wd Paper type Esc amp 6 Wd Plain Esc amp 11 Wd Preprinted Esc amp 11 Wd Letterhead Esc amp 13 Wd Transparency Esc amp 11 Wd Prepunched Esc amp 7 Wd Labels Esc amp 5 Wd Bond Esc amp 9 Wd Recycled Esc amp 6 Wd Color Esc amp 11 Wd Cardstock Esc amp 6 Wd Rough Esc amp 9 Wd Envelope 1 You must spel out the word Transparency in the string although it is abbreviated as TRNSPRNCY on the contro panel 2 The correct command for cardstock is Esc amp n11WdCard Stock with a space between the d and the S and with an uppercase S Parameter settings fax data store parameters E NOTE Refer to the service manual for your HP LaserJet all in one product for information about changing the fax data store parameters 244 Chapter 7 Engineering Details ENWW Installation notes INTRODUCTION Il INSTALLATION INSTRUCTIONS Ill LATE BREAKING INFORMATION IV TECHNICAL ASSISTANCE V LEGAL STATEMENTS I INTRODUCTION PURPOSE OF THIS DOCUMENT This file provides specific installation compatibility and troubleshooting information For additional information about product and driver features see the product user guide and the o
265. scosvaupuestneannriugudentovavassuigeaneunreoinaasceensvuennainet 3 User AGC eMC ccssaiseizouiis psanaibiniccers ee a T 4 HP LaserJet Pro CM1410 Color MFP Series User Guide 0 cccccceceeeeseeeeeees 4 HP LaserJet Pro CM1410 Color MFP Series Install Notes cceeceeeeeereeees 5 Help and Learn Center iors ueinstecezauesvesnesesied onchuara nevte seine benign eunsuancnaadnenedenanatatate 5 Administrator documentation a cnssastonsoduanraxiesuelierobdnasselonseintuanscteduaedainnbcasscbesunebienibn 5 HP Driver Configuration Utility User Guide eccceeeeceeeseeeeeneeeeeneeeeseeeeteeees 6 BAGCAN CEE 6 Software availability and localization a recsies erseerdeediaeshe mreiabieretin neo ees neans 7 Printing system software on the Web sccccesseeeseeeenreeeeneeeeeneeecseaeeessneeeseneeeseaeeeneas 7 In box printing system software CD s sssssssseseisseerssessrtsssetssreretrssersssrrssrerser 7 HP LaserJet Windows software CD cccccesseeeeeestteeeeeseneeesseeees 7 CD versions and language support ccceesceeeesseeeeeteeeenteeeeeses 9 2 Windows software descriptions 4 ciiscisisesssccsssscssssosssennsessasesecesnessovesssvoossvecseseissonovesestoadsens 15 Inirod ctio n ecto deat reheated a dee whet ace ined e eran en eaten 15 Windows printing system software 6 cinesscunicrasumscsanexeveguosdsinprieideneoiudaprenineasuabduaubiiedguonhandzananeardint 16 Windows printing system software iicisccacncdsinias
266. shooting Sets all settings to the factory default values 143 Network Setup menu In the following table items that have an asterisk indicate the factory default setting Menu item Sub menu item Wireless Menu wireless models only Wireless Setup Wizard Description Guides you through the steps to set up the product on a wireless network Wi Fi Protected Setup Run Network Test If your wireless router supports this feature use this method to set up the product on a wireless network This is the simplest method Tests the wireless network and prints a report with the results Turn Wireless On Off Enables or disables the wireless network feature TCP IP Config Automatic Automatic The product automatically configures all the TCP IP settings via DHCP BootP or AutolP Manual Manual You can manually configure the IP address subnet mask and default gateway The control panel prompts you to specify values for each address section As each address is completed the product prompts for address confirmation before moving to the next one After all three addresses are set the network reinitializes Auto Crossover On Enables or disables the use of a standard 10 100 network cable when the product is directly connected to a computer Off Network Services IPv4 Enable or disable the IPv4 and IPv protocols By default each protocol is enabled IPv6 Link Speed Automatic Sets the link speed manually
267. site offers an option for automatic e mail notification about new software releases NOTE This STR describes drivers that are shipped with the printing system software CD This STR does not describe any drivers that might be released for use by support personnel To view the product support web site from the CD follow these steps 1 In the main screen of the Installer click More Options and then click Web Support 2 Click Product Support printing system software CD The software CD for the HP LaserJet Pro CM1410 Color MFP Series product contains a variety of files for installing the printing system software on the computer This section describes the files that are available on the software CD and provides additional information about support and availability The HP LaserJet Pro CM1410 Color MFP Series comes with two printing system software CDs one for Windows operating systems and one for Macintosh operating systems The files on each CD include documentation files and files that are required in order to install and uninstall the printing system components HP LaserJet Windows software CD ENWW NOTE For information about the contents of the Macintosh CD see Macintosh software and utilities on page 111 The root directory of the Windows software CD contains the AUTORUN EXE file the SETUP EXE file and the following directories e Installer e Languages e Prerequisites e Setup e Utilities Softw
268. sktop to open the installer browser screen 3 In the HP LaserJet installer browser screen double click the product dmg icon then double click the pkg icon This begins the printing system installation NOTE In the HP LaserJet installer browser screen double click the Documentation icon to gain access to the manuals Select a language folder and locate the available guides which are in PDF format The user guide is a PDF file that is named LICM1130 M1210_use_xxww pdf where xx is a language abbreviation 4 The Introduction screen appears Click Continue and then follow the onscreen instructions to complete the printing system software installation E NOTE When the printing system software is installing be patient The installer must perform an initial search of the computer which can take up to 1 minute During this time the installer might appear to be stalled 5 When the printing system software installation is complete click Close 6 Continue with the steps for setting up a product Setup instructions This section contains information about the following topics e Setting up a printer with Mac OS X v10 5 and v10 6 e Troubleshooting the product setup 116 Chapter 5 Macintosh software and utilities ENWW Setting up a printer with Mac OS X v10 5 and v10 6 Complete these steps after completing the printing system software installation 1 If you are installing the product using a USB
269. software The following editable text file types are supported in Readiris e BMP e DCA e DOC e DW e HTM e MM e PDF e RIF e IXTI e WP e WPS e WS e WS2 ENWW Scan software 29 The HP Scan software uses a simple user interface with a list of shortcuts a Restore Defaults button a Advanced Settings button and a Sean button Figure 2 2 HP Scan dialog box HP LaserJet CM1410 Series PCL 6 Scan mw Save as PDF _ m Save as JPEG P o 7 JPEG 4 N E mail as PDF E mail as JPEG Save as Editable Text OCR uy Everyday Scan Restore Defaults Save as PDF Save as JPEG E mail as PDF E mail as JPEG Save as editable text OCR if Readiris software is installed Everyday Scan Select a shortcut adjust settings and click Scan Or create a new shortcut Save as PDF Scan size Letter 8 5 x 11 inches Output type Color Resolution 200 dpi File Type PDF pdF Show scan preview Advanced Settings Create New Shortcut Cancel The list contains any user defined destinations and the following default destination options After you select a destination click Sean to start the scan Click Advanced Settings to open the Advanced Settings dialog box where you can create change or delete the destination options that are available in the list and specify the destination options that are available when you press the Scan button on the product contro
270. stem administrators INSTALLING SOFTWARE amp NOTE Connecting the product to the computer using a USB cable before installing software also called Plug and Play is not recommended See the installation guide for more information NOTE Administrator privileges are required to install the printing system on all Windows operating systems 1 Quit all programs 2 Insert the CD ROM 3 If the HP printing system installer program has not started after 30 seconds complete steps 4 through 8 4 Click Start and then select Computer or My Computer from the right hand Start menu 5 Browse to the root directory for the CD ROM drive ENWW Installation notes 247 6 Double click the AUTORUN EXE file 7 When the main menu appears click Install button to start the software installation 8 Follow the onscreen instructions instructions to complete the software installation Printing system installation from the CD or Internet download for network and USB connections E NOTE Ifyou download the printing system or driver from the Internet you might need to first run the EXE file s If SETUP EXE does not run automatically browse to its root location double click the file and follow the onscreen instructions Port selection When the installation process is complete you might need to assign the product to a port on your network if you did not assign a port during setup Perform one of the following procedures
271. sure that the printer driver is installed correctly General Windows installation for network connections e Network setup e Windows installation instructions for network connected products e Printer driver only installation instructions Microsoft Add Printer Wizard Network setup E NOTE Set up turn on and connect the product to the network before installing the software To connect a product to a network use the following instructions 1 Connect the product to the network 2 Turn on the product NOTE You must complete the power up sequence in this order or the installer discovery utility fails to recognize the product It might take a few minutes for the product to obtain a TCP IP address 3 To print a configuration page from the product control panel touch Setup Use the arrow buttons to select Reports and then touch OK Use the arrow buttons to select Config Report and then touch OK 4 Install the printing system software Use the information from the test pages to specify the network variables during installation amp NOTE A second page prints On that page the Fax Settings and Imaging Settings sections provide details about the product fax settings Windows installation instructions for network connected products E NOTE Complete the network setup before completing this procedure ENWW Each computer that has the printing system software installed can use all of the product featu
272. t 72 Chapter 4 HP PCL 6 print driver and HP PS Universal Print Driver for Windows ENWW e Manual Feed in Tray 1 e Tray 1 100 sheet multipurpose tray The default setting is Automatically Select When this setting is selected the HP LaserJet Pro CM1410 Color MFP Series uses the source tray that supports the paper size that you have selected If you select a source tray other than Automatically select make sure that the correct paper size is loaded in the source tray Paper type ENWW The Paper type drop down menu shows the first few paper types that the HP LaserJet Pro CM1410 Color MFP Series supports and an entry for More Clicking More opens the Type Is dialog box Click the next to Type Is and its subcategories to view all of the paper types that the product supports listed in the following categories e Everyday lt 96g o Unspecified gt Plain gt HP LaserJet 90g Light 60 74g Bond o Recycled e Presentation 96 130g gt HP Color Laser Matte 105g o gt HP Premium Choice Matte 120g o Mid Weight 96 110g gt Mid Weight Glossy 96 110g e Brochure 131 175g gt HP Color Laser Brochure Matte 160g gt HP Superior Laser Matte 160g gt HP Color Laser Brochure Glossy 160g gt HP Tri fold Color Laser Brochure 160g gt HP Superior Laser Glossy 160g e Photo Cover 176 220g gt HP Cover Matte 200g gt HP Matte Photo 200g Paper Quality tab features 73 gt HP Color Laser Photo Glossy 220g gt HP Color Laser Photo
273. t more computers to the wireless product ccccceeeceeeeeeeetteeeeeeeeeeeeees 200 The wireless product loses communication when connected to a VPN cceceeeeetteeeees 200 xi The network does not appear in the wireless networks list cceeeeeeesteeeeeeeeeteeeees 200 The wireless network is not functioning ccccceecccceseceeeseeceeeseceeeceeeeeceeeeeeseeeeeneaeees 201 Service mode funchons donerer sta sede ra evden tibet ns oun chaser emcee ames 202 Secondary service Menu adiecwcones washer aanndevnns ndecn Ui Uaredadene acai ern wiputasOna lanes 202 Open the secondary service MENU cccceseeeeseceeeeesesneeeeeesseenteeeeeeesnnaaees 202 Secondary service Menu structure ecceeeeeecceeeeeeteeeeeeeeseeeeeeeeeeeeteeeeeeees 202 Product reselsne sese Seceundte tied nections dina Mian ced dedi oah os arena ada e 203 Restore the factory set defaults ccccceeececeeesteeeeeeeneeeeeeenseeeeeesteeeneaes 203 NYRAM initialization ecese i eE OE EE nee eneeis 204 SOIVE TER 01o EMIS EEA T TE A E OatenSutaikaans 204 Fax troubleshooting checklist xciccortejipoty vaio vas ayaa neta arena ee 204 Troubleshoot fax codes and trace reports cccceecceeeeseceeeseeeeeeeeseeeeeeeeeeseeseeeseeeees 206 View and interpret fax error codes cccccceeseceeeseceeeeeeneeeeneeeeeeeeseeeeensaes 206 Fax trace report e orea a es etag eet eee Gwe A e 217 Fax l gs and repons meraes e Aa EEA E EAE O E OE ootinua
274. t the paper sensors Load Tray 1 lt TYPE gt lt SIZE gt Press OK to use available media Description Device is processing a job but the tray does not match Recommended action Load paper in the correct orientation Touch the OK button to use existing tray settings Load Tray 1 lt PLAIN gt lt SIZE gt Cleaning mode OK to start Description Cleaning mode paper prompt Recommended action Load a clean sheet of paper in the correct orientation then touch the OK button to begin the cleaning procedures Magenta Cartridge Low Description The print cartridge is nearing the end of its useful life Recommended action Printing can continue but consider having a replacement supply on hand Magenta in wrong position Description The print cartridge is installed in the incorrect slot Recommended action Make sure that each print cartridge is installed in the correct slot From front to back the print cartridges are installed in this order black cyan magenta and yellow Magenta Very Low Description ENWW Tools for troubleshooting 161 The print cartridge is at the end of its useful life and the At Very Low menu item in the System Setup menu is set to Continue Recommended action To ensure optimal print quality HP recommends replacing the print cartridge at this point You can continue printing until you notice a decrease in print quality Actual cartridge life may vary Once an HP supply has reached very low
275. tant Support Web site where you can find interactive tools and contacts for troubleshooting e Support and troubleshooting This is the main Web site for HP LaserJet Pro CM1410 Color MFP Series product support e Product manuals View or download HP LaserJet Pro CM1410 Color MFP Series product manuals e Check for driver updates Automatically check your print drivers to see whether the correct and most up to date print drivers are installed e Color printing access usage Find information about enabling and disabling color printing and tracking color printjob usage e Shop for supplies Shop online for HP LaserJet Pro CM1410 Color MFP Series product supplies If you have Internet access select any of these items and click Go to open the corresponding HP Web page Device services ENWW Click the Device and Supplies status icon to open the Device Status screen of the HP EWS which shows supply levels and control panel status Click the Print color usage job log icon to print a page that shows information about users print jobs and applications that have printed to the HP LaserJet Pro CM1410 Color MFP Series product Some enterprise customers want to disable the Services tab because it allows users to go to HP Web sites Use the HP Driver Preconfiguration Editor to disable the Services tab The HP Driver Preconfiguration Editor is available at the following Web site www hp com go dcu Services tab features 97 Device
276. te 22 USB menu 150 user guide HP Driver Configuration 6 viewing 4 v V 34 setting 220 version numbers print drivers 18 volume settings 139 W Web Jetadmin configuration plugin 24 Web sites download software 7 Internet Services options Services tab 97 WIA driver 17 34 Windows components software 16 drivers supported 17 software for 125 Windows operating systems Enterprise AutoConfiguration support 21 fonts supported 38 installation options 54 installing printing system 54 Point and Print installation 59 PS emulation fonts supported 40 ENWW Windows OS direct printing FTP 238 direct printing local port 240 direct printing networks 241 driver versions 18 HP Driver Preconfiguration support 25 HP PCL 6 Print Driver features 61 LPR commands 241 software CD 7 wireless configuring 144 Index 259 260 Index ENWW 2010 Hewlett Packard Development Company L P www hp com
277. tem the same printer driver version that is vended from the server to the clients in a Point and Print environment also runs and controls the print queue configuration on the server However in a mixed operating system environment one in which servers and clients might run on different operating systems conflicts can occur when client computers run a version of the printer driver that is different from the one on the print server In an effort to increase operating system stability Microsoft determined that starting with Windows 2000 and continuing with all future operating systems printer drivers would run as usermode processes User mode drivers run in a protected part of the operating system as do all of the normal General Windows installation instructions 59 end user processes and software programs A user mode printer driver that functions incorrectly can terminate or crash only the process in which it is running not the whole operating system Because access to critical system resources is restricted overall operating system stability is increased Modify a pre existing installation If an HP LaserJet Pro CM1410 Color MFP Series MFP Series has been installed the initial Installer screen on the printing system installation CD changes to the Welcome Back screen A pre existing installation also changes the sequence of installation screens Figure 3 1 Installer screen Welcome Back Ap HP LaserJet Professional CM1410 S
278. ternet access to upgrade firmware o Resend the fax Verify that the fax was set up when the product software was installed From the computer in the HP program folder run the Fax Setup Utility 4 5 6 Verify that the telephone service supports analog fax If using ISDN or digital PBX contact your service provider for information about configuring to an analog fax line If using a VoIP service change the Fax Speed setting to Slow V 29 or disable Fast V 34 from the control panel Ask if your service provider supports fax and for the recommended fax modem speed Some companies might require an adapter If using a DSL service ensure that a filter is included on the phone line connection to the product Contact the DSL service provider or purchase a DSL filter if you do not have one If a DSL filter is installed try another since these filters can be defective If the error persists find more detailed problem solving solutions in the sections that follow this one Solve fax problems 205 206 Troubleshoot fax codes and trace reports View and interpret fax error codes Use fax error codes from the fax activity log to solve problems with the product fax features Table 6 4 Fax receive error codes Error code Description Solution 200 The fax session has completed without errors N A 221 User has touched the Cancel X button causing Have the sender resend the fax the fax session to be prematu
279. terpret the Print Quality Page 1 On the product control panel open the Reports menu 2 Select the Print Quality Page item to print it This page contains five bands of color which are divided into four groups as indicated in the following illustration By examining each group you can isolate the problem to a particular print cartridge Section Print cartridge 1 Yellow 2 Cyan 3 Black 4 Magenta e If dots or streaks appear in only one of the groups replace the print cartridge that correlates with that group e If dots appear in more than one group print a cleaning page If this does not solve the problem determine if the dots are always the same color for example if magenta dots appear in all five color bands If the dots are all the same color replace that print cartridge e If streaks appear in multiple color bands contact HP A component other than the print cartridge is probably causing the problem ENWW Improve print quality 185 Inspect the print cartridge for damage 1 Remove the print cartridge from the product and verify that the sealing tape has been removed 2 Check the memory chip for damage 3 Examine the surface of the green imaging drum on the bottom of the print cartridge A CAUTION Do not touch the green roller imaging drum on the bottom of the cartridge Fingerprints on the imaging drum can cause print quality problems 4 If you see any s
280. tes product conditions such as a jam or an empty tray After you correct a problem click Refresh status to update the product status Supplies status View details such as the estimated percent of life remaining in the print cartridge and the number of pages that have been printed with the current print cartridge This page also has links for ordering supplies and for finding recycling information Device configuration View a detailed description of the current product configuration including the amount of memory installed and whether optional trays are installed Network summary View a detailed description of the current network configuration including the IP address and network status Reports Print the Configuration report and other information pages Color usage job log View color usage information for the product Event log View a history of product errors The event log is a table where the product events are logged for your reference The log contains codes that correspond to the error messages that appear on the product control panel display The number in the Page Count column specifies the total number of pages that the product had printed when the error occurred The most recent error is listed first Tools for troubleshooting 125 Fax Use the HP ToolboxFX Fax tab to perform fax tasks from your computer The Fax tab contains links to the following main pages Fax Receive Fax Receive Set the fax receive mode Fax Ph
281. the OK button to resume or by touching the Cancel X button to cancel the job With certain warnings the job might not complete or the print quality might be affected If the alert or warning message is related to printing and the auto continue feature is on the product will attempt to resume the printing job after the warning has appeared for 10 seconds without acknowledgement Critical error messages can indicate some kind of failure Turning off and then turning on the power might fix the problem If a critical error persists the product might require service Control panel messages 10 100X Supply Memory Error Description A specific print cartridge has a faulty or missing memory chip X indicates the cartridge O black 1 cyan 2 magenta 3 yellow Recommended action Check the memory chip If it is missing broken or damaged replace the cartridge Verify that the cartridge is installed in the correct location Reinstall the print cartridge Turn off and then turn on the product If the error persists replace the cartridge 49 Error Turn off then on Description The product has experienced an internal embedded software error Under most conditions the product automatically restarts Recommended action Turn off the power by using the power switch wait at least 30 seconds and then turn on the power and wait for the product to initialize If the error persists try the following solutions 1 Perform an NVRAM initialization
282. the computer has more than one USB port try a different USB port e Turn the product off and then back on e Turn the computer off and then back on e Ifyou are using a USB hub on the computer disconnect any other USB devices from the hub e Try forcing the product into USB Full Speed mode by using the control panel If the wrong PPD appears in the Kind column in the printer list after installation 1 Unplug the USB cable Delete the print queue with the incorrect type for example Generic PostScript Printer 2 3 Reinstall the printing system software 4 Turn the computer off and then on 5 Reconnect the USB cable from the computer to the product Macintosh install and uninstall instructions 117 If these steps do not resolve the problem delete the incorrect print queue click Add choose the product from the list and then browse manually for the product PPD Remove the printing system software from Macintosh operating systems 1 Open Finder 2 Navigate to Applications HP Laserjet Professional CM1410 MFP Series 3 Double click HP Uninstaller app The uninstaller will run and remove the software 118 Chapter 5 Macintosh software and utilities ENWW 6 Solve problems ENWW Problem solving checklist Troubleshooting process Tools for troubleshooting Menu map Paper feeds incorrectly or becomes jammed Improve print quality Clean the product The product does not print or it print
283. the following methods This utility does not communicate with the product to determine if the settings are valid but it does perform syntax ENWW HP Driver Deployment Utility 47 checking The administrator is responsible for identifying the product using either the correct IP address the Hardware address or the Hostname e IP Address enter the IPv4 or IPv address of the product e Hardware Address enter the hardware address of the product e Hostname enter the hostname of the product The following network settings are additional You may accept the default values pre entered or change any of them e Port Name This is the network port name that will be created If the name already exists a number will be appended to make it unique e Printer Name This is the product name that will appear in the printers folder If the name already exists a number will be appended to make it unique e Set this printer as default o Yes will make this product the default when printing from other applications o No will retain the current default unless this is the only product installed e Share this printer Yes will allow others to use this product e Share Name Share name for the product Only enabled if Share this printer is Yes If the name already exists a number will be appended to make it unique To exit the Network Settings dialog without saving use the Windows close button in the upper corner Package Ta
284. the name of the appropriate printer port such as LPT1 For example type the following C gt copy b c P3010FW PDF Iptl 2 Press Enter on the keyboard E NOTE If the file name or path includes a space you must enclose the file name or path in quotation marks For example type C gt copy b c My Documents P3010FW PDF The message Processing Job appears on the control panel and the job prints 3 At the command prompt type exit to close the command window Print ready file printing in a Windows network If the product is shared on a Windows network complete the following steps 1 From a command prompt or in an MS DOS window type copy b lt FILENAME gt lt COMPUTERNAME gt lt SHARENAME gt where lt FILENAME gt is the name of the printready file including the path lt COMPUTERNAME gt is the name of the computer from which the product is being shared and lt SHARENAME gt is the product share name For example type the following C gt copy b c P3010FW PDF your_server sharename NOTE If the file name or path includes a space you must enclose the file name or path in quotation marks For example type C gt copy b c My Documents P3010FW PDF your_server sharename 2 Press Enter on the keyboard The message Processing Job appears on the control panel and the job prints The message 1 file s copied appears on the computer screen Print ready file printing in UNIX systems For UNIX systems
285. tion occurs in the following circumstances e When a print driver is installed by using the installer e When using the Update Now feature for a driver that is already installed However as shown in the following table driver autoconfiguration and Update Now are not available in Windows XP Windows Server 2003 Windows Server 2008 Windows Vista or Windows 7 operating systems over a direct connection when the HP LaserJet Pro CM1410 Color MFP Series product is installed by using the Add Printer wizard Table 2 2 Automatic discovery and driver configuration through bidirectional communication Connection type Add Printer Wizard install Common installer Network Yes Yes Direct connection No Yes The table applies to Windows XP Windows Server 2003 Windows Server 2008 Windows Vista and Windows 7 Bidirectional communication In environments that support bidirectional communication the computer communicates with the product during installation determines the physical configuration and then configures the driver accordingly Bidirectional communication is the capability of the product to respond to data inquiries from the computer and report information back such as what type of print paper is available or what accessories are connected to the product Bidirectional communication depends on the network operating system and on the type of connection that exists between the computer and the HP LaserJet Pro CM1410 Color MFP Series If t
286. trator s Guide which includes network installation and epee eral Admin Software gt Color Printing Access and Usage Online Get Specialized Drivers Information on enabling disabling color printing and tracking color usage Web Support HP Driver Configuration Utility User Guide To view this guide from the software CD follow these steps 1 In the main screen of the Installer click More Options and then click Admin Documentation 2 Click HP Driver Configuration User Utility Guide HP Jetdirect Guide The HP Jetdirect Guide is a network administrator s guide in PDF format that contains information about connecting the product directly to a network To view this guide from the software CD follow these steps 1 In the main screen of the Installer click More Options and then click Admin Documentation 2 Click HP Jetdirect Guide Chapter 1 Document and product basics ENWW Software availability and localization This section provides information about the availability of the HP LaserJet Pro CM1410 Color MFP Series printing system software and related software and firmware Printing system software on a CD is available from HP fulfillment centers For more information go to the following Web site Printing system software on the Web In box All software that is contained on the installation CD is also available on the Web Web deployment is the preferred method for obtaining the latest software The Web
287. try a different type of USB flash drive Troubleshooting process Power subsystem Power on checks Turn on the power If the control panel LEDs do not illuminate perform the power on checks to find the cause of the problem 1 Verify that the product is plugged into an active electrical outlet that delivers the correct voltage 2 Verify that the power switch is in the on position 3 Make sure that the product makes the expected startup sounds 122 Chapter 6 Solve problems ENWW Tools for troubleshooting Component diagnostics LED diagnostics Network LEDs The onboard network solution has two network port LEDs When the product is connected to a properly working network through a network cable the yellow LED indicates network activity and the green LED indicates the link status A blinking yellow LED indicates network traffic If the green LED is off a link has failed For link failures check all of the network cable connections In addition you can try to manually configure the link settings on the onboard network solution by using the product control panel menus Touch the Setup N button 2 Scroll to and touch the Network Setup menu 3 Touch the Link Speed menu 4 Select one of the following options Setting Description Automatic The print server automatically configures itself for the highest link speed and communication mode allowed on the network 10T Half 10 megabytes per second
288. ts with incompatible sending versions sending diagnostic versions supported by the two products are incompatible 227 The sending product has attempted to initiate a fax Reconfigure the receiving product to receive at a session at a speed and modulation that is not slower speed supported by the receiving product 228 The sending product has attempted to initiate a 1 Confirm that polling by the sender is desired poll transmission from the receiving product even It is possible that the sender has inadvertently though the receiving product is not configured for attempted to poll If this is the case reattempt poll transmission a normal transmission from the sending product 2 If polling by the remote user was desired confirm that the receiving product was correctly configured for poll transmission 229 The sending product has attempted to initiate a If the sender is the desired recipient for the polled secure poll transmission from the receiving product document confirm that the sender has the correct but has not provided a valid password password and that the receiving product is configured with the same password 230 The sending product has attempted to initiate an Enable ECM on both the receiving product and the operation that requires error correction but has not sending product selected error correction for the session 231 The sending product has attempted to initiate a Ensure that the receiving product is capable of transmission to
289. tton to enter the network settings From Network Settings dialog a From the Required Settings section enter at least one way of identifying the product IP address Hardware address or Hostname b Make any changes to the Additional Settings section port name product name default printer sharing and share name You can leave the default settings if you don t need to make changes From Package Target section Select the output name and location Three files will be written here an EXE file a CAB file and an XML file with information about the package Chapter 2 Windows software description ENWW ENWW 5 From Create Package section a Ifyou want to suppress any error messages select the Suppress all end user error messages checkbox b Click the Create Package button c The configuration dialog will open and allow you to set configuration details for this print driver After accepting the configuration changes the package will be created 6 Run the new EXE file from the client computer You must have administrator rights to run the EXE file because it will be copying files into the Windows driver store A port and printer object will be created with the information provided above Common Problems I get a warning when I select the print driver If there are too many files in the driver directory or the directory is really large a warning appears so that the user doesn t accidentally package up something
290. tware starts with the document attached Add a cover page by selecting Cover Page Add pages scanned from the product document feeder by selecting Pages in Document Tray ENWW HP LaserJet Send Fax software 37 Font support The basic fonts listed here are included with Microsoft Windows software The additional PS fonts are available on the CD that came with the product Basic fonts Microsoft Windows software includes these basic fonts which can be used with any HP printing product e Arial e Courier New ltalic Times New Roman Italic Arial Italic Courier New Bold Times New Roman Bold Arial Bold Courier New Bold Italic Times New Roman Bold Italic Arial Bold Italic Symbol Wingdings Courier New Times New Roman Default fonts 38 The following default fonts are installed through a Full Installation of the HP LaserJet Pro CM1410 Color MFP Series printing system software Table 2 8 Default fonts Font name Font style File name Albertus Extra Bold Regular ALBR85W TTF Albertus Medium Regular ALBR55W TTF Antique Olive Regular OLVR55W TTF Antique Olive Bold OLVR75W TTF Antique Olive Italic OLVR56W TTF CG Omega Regular CGOR45W TTF Chapter 2 Windows software description ENWW ENWW Table 2 8 Default fonts continued Font name Font style File name CG Omega Bold CGOR65W TTF CG Omega Bold Italic CGOR66W TTF CG Omega It
291. uplex settings for the network New software programs might be causing compatibility problems The computer or workstation might be set up incorrectly The product is disabled or other network settings are incorrect Poor physical connection 1 2 3 4 Verify that the product is attached to the correct network port using a cable of the correct length Verify that cable connections are secure Look at the network port connection on the back of the product and verify that the amber activity light and the green link status light are lit If the problem continues try a different cable or port on the hub The computer is using the incorrect IP address for the product 196 1 Open the printer properties and click the Ports tab Verify that the current IP address for the product is selected The product IP address is listed on the product configuration page If you installed the product using the HP standard TCP IP port select the box labeled Always print to this printer even if its IP address changes Chapter 6 Solve problems ENWW 3 If you installed the product using a Microsoft standard TCP IP port use the hostname instead of the IP address 4 If the IP address is correct delete the product and then add it again The computer is unable to communicate with the product 1 Test network communication by pinging the network a Open a command line prompt on your computer For Windows click Start click Run an
292. uring phase three which occurs after V 8 before phase4 and before the first T 30 frames are exchanged The transmitting product is unable to send continuous ones at the end of the control channel prior to starting the primary channel This is a V 34 error This error may be associated with line conditions although it is more likely to be due to internal problems with the modem Reattempt the fax transmission at a different time when the receiving product was unable to correctly when telephone line conditions have improved Chapter 6 Solve problems ENWW Fax trace report Table 6 5 Fax send error codes continued Error code 431 440 445 Description The transmitting product has not received a response after aborting a transmission Depending upon when the session is aborted some sending products may not respond It should be noted that the receiving unit always attempts to abort the session in a way that allows the sending product to respond to the final PPS_EOP An error occurred during a V 34 transmission after one or more partial pages image data were transmitted using the primary channel The transmitting product was unable to restart the control channel in order to resume the T30 handshake This typically occurs when the receiving product prematurely disconnects during partial page reception although it is possible it may also be due to compatibility issues Solution N A Reattempt the fax recept
293. ver Deployment Utility Package Source Driver directory Driver found Install Type Silently preload the driver C Show a prompt to connect the printer direct connect only O Silently create network port and install driver Package Target Output Create Package C Suppress all end user error messages ca invent Driver Directory Use the Select Driver button to enter the directory where the print driver resides by browsing or typing it in You should only have one printer driver package in this directory because this utility will package all the files found in this directory and sub directories into the executable file If you have downloaded a compressed printer driver package you must expand it before using this utility In some cases you may have multiple printdriver INF files in the directory sometimes one is for color and another for mono products In this case an additional dialog will allow you to select which print driver to package You will also get a warning if the directory is large This is to help prevent packaging more than one print driver You can choose to continue or not at this point Once the printer driver directory is selected and one print driver has been found the printer driver information is displayed below the directory selection box 46 Chapter 2 Windows software description ENWW For print drivers that support preconfiguration the check box below will be enabled
294. vice is not blocked For example some phone services might prevent long distance calling e _ If an outside line requires a prefix turn on the Dia Prefix option or include the prefix in the speed dial number a From the Home screen touch the Setup amp button b Open the Fax Setup menu c Open the Basic Setup menu ENWW Solve fax problems 225 d Open the Dial Prefix menu e Select the On setting NOTE To send a fax without a prefix when the Dia Prefix option is turned on send the fax manually e Send a fax to an international number a Ifa prefix is required manually dial the telephone number with the prefix Enter the country region code before dialing the phone number c Wait for pauses as you hear the tones on the phone d Send the fax manually from the control panel Unable to send a fax when a phone is connected to the product e Make sure that the telephone is hung up e Make sure that the telephone is not being used for a voice call when faxing e Unplug the phone from the line and then try sending the fax 226 Chapter 6 Solve problems ENWW Solve problems receiving faxes The fax does not respond An error message displays on the control panel A fax is received but does not print Sender receives a busy signal No dial tone Cannot send or receive a fax on a PBX line The fax does not respond The fax has a dedicated phone line Set the Answer Mode option to t
295. vice menu structure Table 6 3 Secondary service menu Menu item Sub menu item Description Service Reports Cont Self Test This item prints a continuous configuration page Error report This item prints an error report that contains the last 5 instances of 49 Error Turn off then on or 79 Error Turn off then on errors Location A list of available locations appears This item sets certain product parameters that are dependent on the location such as the default paper size and the symbol set Scroll to the appropriate location and select Yes to set the location The product automatically restarts after you change the location 202 Chapter 6 Solve problems ENWW Table 6 3 Secondary service menu continued Menu item Sub menu item Description Display test This test verifies that the LEDs and characters on the control panel display function correctly At the beginning of the test each of the LEDs is turned on one at time Touch the OK button to continue to the next LED After the LED test is complete the character test begins by testing the pixels on each line Then each of the 255 characters is displayed in groups of 16 Touch the OK button to continue to the next group of 16 characters You can cancel the test at any time by touching the Cancel X button Button test This test verifies that the control panel buttons function correctly The display prompts you to press each button Color Cal Adjust
296. work connections e Printer sharing disclaimer e Point and Print installation for Windows e Modify a pre existing installation General Windows installation for direct connections e Windows installation instructions for direct connected USB products e Printer driver only installation instructions Microsoft Add Printer Wizard Windows installation instructions for direct connected USB products Use the following instructions to install the printing system software on a computer that is running Win 7 Windows Server 2003 Windows XP or Windows Vista and is directly connected to the product NOTE Set up and turn on the product before installing the software Do not connect the product to the computer until the software installation program prompts you You must have administrator privileges to install the software 1 Quit all open programs 2 Insert the printing system software CD into the CD ROM drive NOTE If the CD ROM does not start automatically click Start click Run and then browse to and double click the SETUP EXE file in the root directory of the printing system software CD 3 Click the appropriate installation type and then follow the onscreen prompts 4 When the installer software prompts you to select how the product will be connected select Directly to this computer using a USB cable and then click Next Follow the onscreen prompts 5 If you are prompted to restart t
297. x 137 alerts setting up 125 Alternative Letterhead Mode supported products 69 Apple Mac OS see Macintosh OS 18 autoconfiguration driver support for 20 autoconfiguration Enterprise about 20 Windows support 21 B bidirectional communication about 20 Enterprise AutoConfiguration 20 bins output jams clearing 178 blank or preprinted pages 75 booklet printing Booklet Layout settings 89 c calibrating color cartridges status viewing with HP Toolbox FX 125 130 203 ENWW CD documentation 3 languages 9 Windows 7 CD ROM installing Macintosh printing system software 116 Macintosh 115 chapter separator pages 76 checklist fax troubleshooting 204 checklists printing 135 CHM files viewing 3 clean touch screen 192 cleaning glass 190 paper path 182 190 Color Color Options settings 93 Color Themes settings 94 Default sRGB setting 94 features print drivers 92 Neutral Gray settings 94 None 95 Photo Adobe RGB 1998 setting 94 Photo sRGB setting 94 Vivid setting 95 color calibrating 130 203 change default settings manually 93 fine tune default settings 93 color alignment calibrating 133 183 color settings adjusting 180 command line printing Windows 238 commands paper source 243 type 244 comparison product models 1 components software Macintosh 112 Windows 16 configuration page 132 configuration driver 23 connectivity bidirectional communication support 20 solving problems 196
298. xt to Virtual printer port for USB 6 If you are using a personal firewall system on the computer it might be blocking communication with the product Try temporarily disabling the firewall to see if it is the source of the problem 7 If your computer or the product is connected to a wireless network low signal quality or interference might be delaying print jobs NOTE A blue LED on the product control panel is illumintated when the wireless function is enabled and available ENWW The product does not print or it prints slowly 193 The product prints slowly If the product prints but it seems slow try the following solutions 1 Make sure the computer meets the minimum specifications for this product For a list of specifications go to this Web site www hp com support CM 14 Oseries 2 When you configure the product to print on some paper types such as heavy paper the product prints more slowly so it can correctly fuse the toner to the paper If the paper type setting is not correct for the type of paper you are using change the setting to the correct paper type 3 If your computer or the product is connected to a wireless network low signal quality or interference might be delaying print jobs 194 Chapter Solve problems ENWW Solve walk up USB printing problems e The USB Flash Drive menu does not open when you insert the USB accessory e The file does not print from the USB storage accessory e Th
299. yellow 59 7000 Black developer motor startup error 59 7300 Yellow developer motor startup error 59 8000 Black developer motor rotation error 59 8300 Yellow developer motor rotation error 59 9000 Main motor start error Tools for troubleshooting 169 Menu map Use the following procedure to print a control panel menu layout map 1 From the Home screen touch the Setup button 2 Touch the Reports button 3 Touch the Menu Structure button 170 Chapter 6 Solve problems ENWW Paper feeds incorrectly or becomes jammed The product does not pick up paper The product picks up multiple sheets of paper Prevent paper jams Clear jams The product does not pick up paper If the product does not pick up paper from the tray try these solutions 1 2 3 Open the product and remove any jammed sheets of paper Load the tray with the correct size of paper for your job Make sure the paper guides in the tray are adjusted correctly for the size of paper Adjust the guides so they are touching the paper stack without bending it The product picks up multiple sheets of paper If the product picks up multiple sheets of paper from the tray try these solutions 1 Remove the stack of paper from the tray and flex it rotate it 180 degrees and flip it over Do not fan the paper Return the stack of paper to the tray Use only paper that meets HP specifications for this product Use paper that is not wrinkled folded

HP CM1415fn Reference Guide

Contents

Download Pdf Manuals

Related Search

Related Contents