HP E5000 Quick Start Guide
Contents
1. The HP E5000 Messaging System for Microsoft Exchange ues ff flln ooo au Figure 3 E5300 Messaging System sample network HP E5000 Messag ING System is the general name for several E5x00 hardware software IMPORTANT Included with your messaging system cabling for Microsoft Excha nge Qu ick solutions for Microsoft Exchange Each messaging system is the Recovery DVD This DVD is used to restore features HP server blades and dense disk storage the system to factory defaults and should be kept in Sta rt Gu ide combined in a single 3U chassis as shown in a sate place Figure 1 page 1 and Microsoft Exchange setup utilities The Microsoft Windows Server operating system is preinstalled and activated on all systems Supporting documentation Figure 1 HP E5000 Messaging System all models For additional information see the following titles Q F gw x I lait ez ae REFS it gt Er ar Hh h AES gE gt t rf n J m e HP E5000 Messaging System for Microsoft Exchange Administrator Guide e HP StorageWorks 3U Storage System Rail Kit Installation Instructions in the rail kit e HP StorageWorks 2U Storage System Rail Kit Installation Instructions to rack expansion disk es S M 1 Disk drawer enclosures 1 Client MAPI network 2 Server blade 1 Bay 1 e HP Integrated Lights Out 2 User Guide 2 Replication network mei OOE Payee For messaging system titles browse to www hp2. com go eile ee ne E5000 Select HP Support amp Drivers and your product 4 Domain controller The instructions in this quick start guide apply to all Then select Manuals The localized versions of this Quick messaging system models unless otherwise noted Start Guide are also located on the Manuals page Figure 4 E5500 and E5700 Messaging Systems sample Refer to Figure 2 page 1 to locate components network cabling referenced elsewhere in this guide Figure 2 E5000 Messaging System rear view Install the messaging system hardware Copyright 2011 Hewlett Packard Development Company L P A WARNING The messaging system is heavy Always use at least two people to move the storage system into the rack edition 1 January 2011 The information in this document is subject to change without notice Printed in Puerto Rico 1 If you ordered the messaging system without the rack install the rail kit and messaging system chassis by following the HP StorageWorks 3U Storage System Rail Kit Installation Instructions packaged with the rail kit 2 Install any expansion disk enclosures a Add expansion disk enclosures to the rack by www hp com following the HP StorageWorks 2U Storage 1 Client MAPI network 2 port Ethernet module server blades 1 and 2 2 System Rail Kit Installation Instructions packaged 2 Replication network 2 SAS I O module 2 with the rail kit 3 File share witness b Cable t
3. the EMU addressing to DHCP type set ipconfig dhcp at the command line prompt NOTE Changing the network configuration of the EMU and iLO 2 management processor makes them inaccessible unless you connect the EMU to the network you contigured them for Access the messaging system Connect to the messaging system using either the remote console iLO 2 described above or a direct KVM connection as shown in For direct access page 2 The iLO 2 remote console is the recommended method For instructions on using each access method see the HP E5000 Messaging System for Microsoft Exchange Administrator Guide or the HP Integrated Lights Out 2 User Guide Contigure the messaging system The messaging system should be powered up and the network ports cabled for your network configuration including the EMU port Complete the following steps first on server and then on server 2 Do not start on the second server until you have completed the steps on server 1 1 Enter your locale information in the Windows setup dialog and accept the license terms The Windows setup will complete in approximately 15 minutes and the HP E5000 Messaging System Configuration Wizard will start 2 Enter the EMU Administrator password as instructed in the E5000 Configuration Wizard window ha HP E5000 Messaging System Configuration Wizard E Enclosure E5000 1 EM nas lab at 16 78 91 70 Please enter the Administrator password for the E5300 En
4. atic addresses which need to be contigured to either DHCP or appropriate static addresses for your network environment The preconfigured static addresses are e EMU 10 0 0 10 e Server bladel iLO 2 10 0 0 11 e Server blade2 iLO 2 10 0 0 12 e Subnet mask 255 255 255 0 NOTE blades The EMU must share a LAN with the server 1 Connect a system in the environment or a laptop to the EMU port as shown in Figure 2 page 1 Use an Ethernet cable connected directly to the system or through a switch Configure the NIC on your system to a static address of 10 0 0 20 with the subnet mask detined above 2 Open a web browser and log into iLO 2 for each server blade using the addresses listed above and the Administrator password from the blade pullout tab in the front of the messaging system 3 Configure the iLO 2 networking settings using the tools under the Administration tab in the web browser instance for each server Optionally change the Administrator password before changing the network settings 4 Using a secure shell application putty for example log in to the EMU using the address listed above The Administrator password is on the label attached to the messaging system Configure the following a Change your EMU password by typing set password at the command line prompt b To change the static IP address type the command set ipconfig static atthe command line prompt and follow the instructions c To change
5. closure Manger EMU The default EMU Administrator password is printed on a label attached to the underside of the EMU module and a copy of the label was attached to the rear chassis but should be torn off and stored in a safe place Password The wizard automatically runs a diagnostics program to ensure that the messaging system is correctly configured An error message appears describing any configuration errors and how to fix them When the configuration is correct the E5000 Configuration Wizard resumes 3 Step through each menu option in the wizard to complete the minimum required configuration a Set time zone b Set Administrator password c Set network configuration d Identify computer name e Review report and complete installation contiguration 4 Click Finish This completes the system configuration for one server Next you will configure the server for Microsoft Exchange 5 Run the Quick Deployment Tool and configure Exchange Server 2010 on the server configured in the previous steps For instructions on running the Quick Deployment Tool see the HP E5000 Messaging System for Microsoft Exchange Administrator Guide When you have completed the E5000 Configuration Wizard and the Quick Deployment Tool for server 1 and server 2 the messaging system is ready for use Cabling expansion disk enclosures If your product includes expansion disk enclosures be sure to rack and cable the expansion disk
6. enclosures before powering on the messaging system for initial configuration The following figures show the correct cabling of expansion disk enclosures to the messaging system chassis Figure 5 Cabling two additional expansion disk enclosures i VEN Ly PSE U E ak Osea tal i THE I Ipc g i _ j r on i ia 3 ESF Cs EE alr Page 2 Figure 6 Cabling four additional expansion disk enclosures jie aan ee z Ne Ly Wi 4 ie AEA j O Fas eee 5 A O JA B ty jo 3J ee 1 T 1 1 ayer I RS Numbers represent the order of attachment For direct access To use a direct KVM connection for the initial configuration follow these steps 1 Attach the SUV cable supplied with the messaging system to the port on the front of the server blade as shown in Figure 7 page 2 2 Connect the following cables not supplied to the free ends of the SUV cable in this sequence a keyboard b mouse c monitor cable d power cable Figure 7 KVM console connections
7. he expansion disk enclosures to the messaging system chassis For recommended cabling see Figure 5 page 2 and 3 Power button 4 Domain controller 4 Power supply 2 For more information about connecting the messaging Pore edb a server blades 1 and 2 2 on E5500 and Figure 6 page 2 sysienr oyournehvetk 6rioeeblenourneived models only a EE Se differently from these examples see the HP E5000 6 Management port for iLO 2 and Enclosure Manager IMPORTANT Ensure that cabling in the back y te of the rack does not interfere with system Herne i System P Microsoft Exchange operation or maintenance Bind cables loosely Administrator Guide with cable ties and route excess out of the way 4 Connect the messaging system power cords to the along the side of the rack rack power supply using standard procedures 3 Connect the messaging system network cables See the following cabling examples Use the short a n that en system ns H or the replication network connection lurn on any expansion disk enclosures en Power on the messaging system Page 2 Turn on the messaging system by pushing the power button on the back of the chassis as shown in E5000 Messaging System rear view page 1 Once the messaging system power is on turn on the server blades if they do not automatically power on Configure the EMU and iLO 2 network ports The EMU and iLO 2 ports come preconfigured with st
Download Pdf Manuals
Related Search