HP Compaq TFT 1825 User's Manual
Contents
1. by this product The complete environmental criteria document may be ordered from TCO Development SE 114 94 Stockholm Sweden Fax 46 8 782 92 07 Email Internet development tco se Current information regarding TCO 99 approved and labelled products may also be obtained via the Internet using the address http www tco info com Environmental requirements Flame retardants Flame retardants are present in printed circuit boards cables wires casings and housings Their purpose is to prevent or at least to delay the spread of fire Up to 30 of the plastic in a computer casing can consist of flame retardant substances Most flame retardants contain bromine or chloride and those flame retardants are chemically related to another group of environmental toxins PCBs Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects including reproductive damage in fish eating birds and mammals due to the bioaccumulative processes Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur User s Guide 27 Agency Regulatory Notices The relevant TCO 99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine Flame retardants are allowed in the printed circuit boards since no substitutes are available Cadmiu2. from the outlet Never disconnect it by pulling the cord Unplug the monitor from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Slots and openings in the cabinet are provided for ventilation These openings must not be blocked or covered Never push objects of any kind into cabinet slots or other openings Do not drop the monitor or place it on an unstable surface Do not allow anything to rest on the power cord Do not walk on the cord User s Guide E Keep the monitor in a well ventilated area away from excessive light heat and moisture Keep the monitor away from high capacity transformers electric motors and other strong magnetic fields E Do not open the monitor cabinet or attempt to service this product yourself Adjust only those controls that are covered by the operating instructions If the monitor is not operating properly or has been dropped or damaged contact your authorized dealer reseller or service provider Cleaning the Monitor To clean the monitor follow these steps 1 Turn off the monitor and the computer 2 Dust the monitor by wiping the screen and the cabinet with a soft clean cloth If the screen requires additional cleaning use a clean cloth dampened with isopropyl alcohol CAUTION Do not use benzene thinner ammonia or any volatile substance to clean the monitor screen or cabinet These chemicals may damage the monitor Never use water to c
3. must connect the other end of the DVI D cable to the DVI connector on the computer 3 Connect the monitor signal cable to the back of the monitor 4 Connect the power cable to the back of the monitor 5 Connect the power cable to an electrical wall outlet User s Guide 6 Adjust the monitor as needed for your comfort using the monitor s tilt swivel and height adjustment capabilities You can change your monitor s viewing position to portrait To rotate your display to the portrait position you will need to install the Pivot software which is contained on the CD included with your monitor User s Guide p User s Guide WARNING To reduce the risk of electric shock or damage to your equipment Do not disable the power cord grounding plug The grounding plug is an important safety feature Plug the power cord into a grounded earthed electrical outlet that is easily accessible at all times Disconnect power from the monitor by unplugging the power cord from the electrical outlet Do not place anything on power cords or cables Arrange them so that no one may accidentally step on or trip over them Do not pull on a cord or cable When unplugging from the electrical outlet grasp the cord by the plug CAUTION Burn in image damage may occur on monitors that display the same static image on screen for a prolonged period of time To avoid burn in image damage on you
4. 0 K 0 31 0 329 9300 K 0 28 0 31 Gamma 2 2 Commission International d Eclairage 1931 Standard 20 User s Guide Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures E Reorient or relocate the receiving antenna E Increase the separation between the equipment and the receiver E Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio or television technician for help User s Guide 21 Agency Regulatory Notices Modifications The FCC requires the user to be notified that any changes or modifications made to this device t
5. 5 0 13 1280 x 1024 63 9 60 0 14 1280 x 1024 80 0 75 0 15 75 0 60 0 1600 x 1200 Entering User Modes The video controller signal may occasionally call for a mode that is not preset if You are not using a standard graphics adapter E You are not using a preset mode If this occurs you may need to readjust the parameters of the monitor screen by using the on screen display Your changes can be made to any or all of these modes and saved in memory The monitor automatically stores the new setting then recognizes the User s Guide new mode just as it does a preset mode In addition to the 15 factory preset modes there are four user modes that can be entered and stored Energy Saver Feature When the monitor is in its normal operating mode the monitor uses less than 60 watts of power and the Power light is green The monitor also supports a reduced power state The reduced power state will be entered into if the monitor detects the absence of either the horizontal sync signal and or the vertical sync signal Upon detecting the absence of these signals the monitor screen is blanked the backlight is turned off and the Power light is turned amber When the monitor is in the reduced power state the monitor will utilize less than 5 watts of power There is a brief warm up period before the monitor will return to its normal operating mode Refer to your computer manual for instructions on setting energy saver featu
6. O invent User s Guide 1825 Flat Panel Monitor Document Part Number 305223 001 August 2002 2002 Hewlett Packard Company Compaq and the Compaq logo are trademarks of Compaq Information Technologies Group L P in the U S and other countries All other product names mentioned herein may be trademarks of their respective companies Hewlett Packard Company shall not be liable for technical or editorial errors or omissions contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material The information in this document is provided as is without warranty of any kind including but not limited to the implied warranties of merchantability and fitness for a particular purpose and is subject to change without notice The warranties for HP products are set forth in the express limited warranty statements accompanying such products Nothing herein should be construed as constituting an additional warranty This document contains proprietary information that is protected by copyright No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Hewlett Packard Company WARNING Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life CAUTION Text set off in this manner indicates that failure to follow directions could re
7. choice has provided you with a product developed for professional use Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products Why do we have environmentally labelled computers In many countries environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment The main problem as far as computers and other electronics equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture Since it is not so far possible to satisfactorily recycle the majority of electronics equipment most of these potentially damaging substances sooner or later enter nature There are also other characteristics of a computer such as energy consumption levels that are important from the viewpoints of both the work internal and natural external environments User s Guide 25 Agency Regulatory Notices Since all methods of electricity generation have a negative effect on the environment e g acidic and climate influencing emissions radioactive waste it is vital to save energy Electronics equipment in offices is often left running continuously and thereby consumes a lot of energy What does labelling involve This product meets the requirements for the TCO 99 scheme which provides for international and environmen
8. d can be found in picture tubes display screens solders and capacitors Lead damages the nervous system and in higher doses causes lead poisoning The relevant TCO 99 requirement permits the inclusion of lead since no replacement has yet been developed Bioaccumulative is defined as substances which accumulate within living organisms Lead Cadmium and Mercury are heavy metals that are Bioaccumulative Power Cord Set Requirements The monitor power supply is provided with Automatic Line Switching ALS This feature allows the monitor to operate on input voltages between 100 120V or 200 240V The power cord set flexible cord or wall plug received with the monitor meets the requirements for use in the country where you purchased the equipment If you need to obtain a power cord for a different country you should purchase a power cord that is approved for use in that country The power cord must be rated for the product and for the voltage and current marked on the product s electrical ratings label The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product In addition the cross sectional area of the wire must be a minimum of 0 75 mm or 18AWG and the length of the cord must be between 6 feet 1 8 m and 12 feet 3 6 m If you have questions about the type of power cord to use contact your Compaq authorized service provider User s Guide 29 Agency Regu
9. e CE Marking comply with both the EMC Directive 89 336 EEC and the Low Voltage Directive 73 23 EEC issued by the Commission of the European Community Compliance with these directives implies conformity to the following European Norms in brackets are the equivalent international standards E ENS55022 CISPR 22 Electromagnetic Interference E ENS55024 IEC61000 4 2 3 4 5 6 8 11 Electromagnetic Immunity mM EN61000 3 2 TEC61000 3 2 Power Line Harmonics mM EN61000 3 3 CEC61000 3 3 Power Line Flicker E EN60950 IEC950 Product Safety User s Guide 23 Agency Regulatory Notices Japanese Notice TOREA ARES ERS EMRE VCCI OR TEO 77 ABIGRETEE CT I ORB RERE CHATS PANMELTWETR COBRERIVARFUEY ay SIC LT MASNAL SMBS EITI HEVET Ba BIE TE LUO RW LT FAY T EPA Energy Star Compliance Monitors that are marked with the Energy Star Logo meet the requirements of the EPA Energy Star program As an Energy Star Partner Compaq Computer Corporation has determined that this product meets the Energy Star guidelines for energy efficiency Specific details on using the Energy Saving features can be found in the energy saver or power management section of the computer manual 24 User s Guide Agency Regulatory Notices TCO 99 Congratulations You have just purchased a TCO 99 approved and labelled product Your
10. hat are not expressly approved by Compaq Computer Corporation may void the user s authority to operate the equipment Cables Connections to this device must be made with shielded cables with metallic RFI EMI connector hoods to maintain compliance with FCC Rules and Regulations Declaration of Conformity for Products Marked with FCC Logo United States Only This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For questions regarding your product contact Compaq Computer Corporation P O Box 692000 Mail Stop 530113 Houston Texas 77269 2000 Or call 1 800 652 6672 1 800 OK COMPAQ For questions regarding this FCC declaration contact Compaq Computer Corporation P O Box 692000 Mail Stop 510101 Houston Texas 77269 2000 Or call 281 514 3333 22 User s Guide Agency Regulatory Notices To identify this product refer to the Part Series or Model number found on the product Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Avis Canadien Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada European Notice Products with th
11. he monitor is operating in the DVI D digital mode Adjusting Monitor Settings On the front panel controls of your monitor once you press the menu button the On Screen Display OSD Main Controls window will pop up and you can now start making adjustments to your monitor s various features Use the left right up and down arrow keys in the menu window to make your adjustments User s Guide MAIN CONTROLS ADJUST POSITION BRIGHTNESS amp CONTRAST VIDEO NOISE ADJUST COLOR OSD SETTINGS PRODUCT INFORMATION RESET TO FACTORY SETTINGS INPUT SELECTION EXIT MAIN CONTROLS MOVE SELECTION THEN MENU Adjusting Screen Quality Allow the monitor to warm up for 20 minutes before performing the following procedures The Auto Adjustment feature automatically fine tunes the image quality each time a new video mode is utilized If additional improvement is desired select the Auto Adjust control on the front bezel For more precise adjustments use the adjustment pattern provided on the CD ROM and adjust the clock and phase settings accessed from the OSD menu as described in the following section User s Guide 13 Optimizing Digital Conversion D This monitor contains advanced circuitry that allows the flat panel screen to function like a standard monitor Two controls in the on screen display can be adjusted to improve image performance Clock and Clock Phase Use these controls only when the aut
12. justs settings User s Guide 9 Front Panel Controls No Control Function 4 Brightness e Adjust brightness up and down when the OSD is off e Use the up and down buttons to navigate through the OSD menus when the OSD is on Power LED llluminates green when the monitor is on and turns amber when the monitor is in a power saver mode 6 Power Switch Turns the monitor on and off User s Guide On Screen Display Settings The adjustments for screen settings are located in the on screen display OSD Press the menu button on the monitor s front panel to view the OSD menu in one of seven available languages The following table shows the menus and their functions at each level OSD Menu Levels Menu Level Menu Level Menu Level Menu Level 1 2 3 4 Adjust Position Horizontal Vertical Brightness amp Brightness Contrast Contrast Video Noise Phase Clock Adjust Color Original Panel Color 9300K for CAD CAM 6500K for Image Management User Preset Red Green Blue OSD Settings Horizontal Vertical Product Serial No Information Resolution User s Guide OSD Menu Levels Menu Level Menu Level Menu Level Menu Level 1 2 3 4 Video Input Reset to Factory No Setting Yes Input Selection Analog D Sub Digital DVI Analog DVI Exit Main Controls The Video Noise OSD selection is not available when t
13. lat front bezel down and that the base is set to the maximum base extension Attempting to remove the monitor from the base while upright in the minimum base extension may result in injury to the user 1 Disconnect and remove the signal and power cables from the back of the monitor User s Guide 7 2 Remove the four screws as shown in the following illustration CAUTION Ensure that the bottom of the monitor base is positioned over a table or desktop before removing the base from the monitor 3 Remove the monitor base from the monitor Mounting the Monitor 1 Remove the monitor base Refer to Removing the Monitor Base steps in the previous section When the base is removed four threaded mounting holes are exposed on the monitor panel to be used for mounting purposes These mounting holes are spaced 100 mm apart and are compliant with the Video Electronics Standards Association VESA standard for mounting flat panel displays 8 User s Guide 2 Mount the monitor to a swing arm or other mounting fixture by following the instructions included with the mounting fixture to be used Operating the Monitor rae Front Panel Controls No Control Function o Auto button Automatically adjusts the displayed image Input button Allows you to switch to and from the VGA and DVI I video signal inputs when the OSD is off Menu Navigates through the OSD option icons and ad
14. latory Notices A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it Particular attention should be paid to the plug electrical outlet and the point where the cord exits from the product 30 User s Guide
15. lean an LCD screen Shipping the Monitor Keep the original packing box in a storage area You may need it later if you move or ship your monitor 18 User s Guide Specifications 1825 Flat Panel Monitor Display 18 1 inches 46 cm Type TFT LCD Viewable Image Size 18 1 inch 46 cm diagonal Tilt 5 to 35 Swivel 35 to 35 Face Treatment Anti glare polarizer with hard coating Maximum Weight 22 9 Ibs 10 4 kg Unpacked unpacked Dimensions includes pedestal Height 19 9 inches 506 mm Depth 8 2 inches 208 mm Width 15 8 inches 402 mm Graphics Resolutions 1280 x 1024 75 Hz analog and digital modes 1600 x 1200 60 Hz analog mode only Text Mode 720 x 400 Dot Pitch 0 279 x 0 279 mm Horizontal Frequency 30 to 82 kHz analog mode Vertical Refresh Rate 56 to 76 Hz analog mode User s Guide 19 1825 Flat Panel Monitor Environmental Requirements Temperature Operating Temperature 32to 95 F O to 35 C Non operating Temperature 4 to 140 F 20 to 60 C Relative Humidity 20 to 80 Power Source 100 240 VAC 50 60 Hz Power Consumption lt 60 watts typical Input Terminals 15 pin D type connector with cable included DVI I connector with DVI D cable included Color Display Values CIE Chromaticity Coordinates x 0 030 y 0 030 Red 0 63 0 34 Blue 0 141 0 096 Green 0 295 0 600 White Chromaticity 650
16. m Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer displays Cadmium damages the nervous system and is toxic in high doses The relevant TCO 99 requirement states that batteries the colour generating layers of display screens and the electrical or electronics components must not contain any cadmium Mercury Mercury is sometimes found in batteries relays and switches It damages the nervous system and is toxic in high doses The relevant TCO 99 requirement states that batteries may not contain any mercury It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit There is however one exception Mercury is for the time being permitted in the back light system of flat panel monitors as there today is no commercially available alternative TCO aims on removing this exception when a mercury free alternative is available CFCs freons The relevant TCO 99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product CFCs freons are sometimes used for washing printed circuit boards CFCs break down ozone and thereby damage the ozone layer in the stratosphere causing increased reception on earth of ultraviolet light with e g increased risks of skin cancer malignant melanoma as a consequence 28 User s Guide Agency Regulatory Notices Lead Lea
17. o adjust function does not provide a satisfactory image The Clock must first be set correctly since the Clock Phase settings are dependent on the main Clock setting E Clock Increase decrease the value to minimize any vertical bars or stripes visible on the screen background E Clock Phase Increase decrease the value to minimize video distortion or video jitter When using the controls you will obtain the best results by using the adjustment pattern application provided on the CD ROM When adjusting the Clock and Clock Phase values if the monitor images become distorted continue adjusting the values until the distortion disappears To restore the factory settings select Yes from the Factory Reset menu in the on screen display Recognizing Preset Display Resolutions The display resolutions listed below are the most commonly used modes and are set as factory defaults This monitor automatically recognizes these preset modes and they will appear properly sized and centered on the screen User s Guide Factory Preset Display Modes Preset Pixel Format Horz Freq kHz Vert Freq Hz 1 640 x 350 31 5 70 0 2 720 x 400 31 5 70 0 3 640 x 480 31 5 60 0 4 640 x 480 37 9 72 0 5 640 x 480 37 5 75 0 6 800 x 600 35 2 56 0 7 800 x 600 37 9 60 0 8 800 x 600 46 9 75 0 9 832 x 624 49 7 75 0 10 1024 x 768 48 4 60 0 11 1024 x 768 60 0 75 0 12 1152 x 870 69 0 7
18. r monitor screen you should always activate a screen saver application or turn off the monitor when it is not in use for a prolonged period of time Selecting the Signal Connectors and Cables There are two signal input connectors one VGA connector and one DVI I connector The monitor will automatically determine which inputs have valid video signals The inputs can be selected via the On Screen Display OSD feature or by pressing the Signal Input Selection control on the monitor front bezel The video mode supported by the DVI I connector is determined by the video cable used For digital operation use the DVI D to DVI D signal cable provided For analog operation a DVI I to VGA signal cable must be attached to the DVI I input not provided with the monitor 6 User s Guide Removing the Monitor Base You can remove the monitor base to mount the monitor on a wall a swing arm or other mounting fixture To remove the monitor from the base read the caution and warning below before beginning the procedure CAUTION Before beginning to disassemble the monitor be sure the monitor is turned off and the power and signal cables are both disconnected Lay the front bezel down on a soft area to prevent it from getting scratched defaced or broken WARNING Do not remove the base from the monitor while the monitor is in the upright position Before removing the monitor from the base ensure that the monitor is lying f
19. res sometimes called power management features Q The above energy saver feature only works when connected to computers that have energy saver features By selecting settings in the monitor s Energy Saver utility you can also program the monitor to enter into the reduced power state at a predetermined time When the monitor s Energy Saver utility causes the monitor to enter the reduced power state the Power light blinks amber Care and Maintenance Use the following guidelines to care for and maintain your monitor during normal everyday use 16 User s Guide Protecting the Monitor To protect your monitor from overheating and other types of damage Use only a power source and connection appropriate for this monitor as indicated on the marking label back plate and the AC adapter If an extension cord or power strip is used make sure that the cord or strip is rated for the product and that the total ampere ratings of all products plugged into the extension cord or power strip do not exceed 80 of the extension cord or strip ampere ratings limit Do not overload an electrical outlet power strip or convenience receptacle The overall system load must not exceed 80 of the branch circuit rating If power strips are used the load should not exceed 80 of the power strip input rating Install the monitor near an outlet that you can easily reach Disconnect the product by grasping the plug firmly and pulling it
20. s two information files to be installed onto your computer an INF file and an ICM file E The INF file defines monitor resources and provides specifications used by most operating systems to install support software for certain hardware devices The INF file ensures monitor compatibility and optimization with your computer s graphics adapter INF files are downloadable by clicking on www hp com go support and selecting the desired monitor E The ICM file provides color matching consistency from monitor screen to printer and is activated from within graphics programs that have this feature To install these files on your computer insert the Software and Reference Library CD in your computer CD ROM drive When the CD menu launches select Install INF and ICM Files and follow the on screen instructions Setting Up the Monitor To set up the monitor ensure that the power is turned off to the monitor computer system and other attached devices then follow these steps 1 Place the monitor in a convenient well ventilated location near your computer 2 Connect the monitor signal cable to the video connector on the rear panel of the computer 2 User s Guide Qi The DVI D cable supplied with this monitor is for digital to digital connection only Your computer must have a DVI compatible graphics card installed for use with this cable When connecting the DVI D signal cable to the DVI connector on the monitor you
21. sult in damage to equipment or loss of information User s Guide 1825 Flat Panel Monitor First Edition August 2002 Document Part Number 305223 001 Product Features The 1825 Flat Panel Display has an active matrix thin film transistor TFT liquid crystal display LCD The monitor features include Large 18 1 inch 45 9 cm viewable area display 1280 x 1024 native resolution plus full screen support for lower resolutions Wide viewing angle to allow viewing from a sitting or standing position or moving side to side Tilt and swivel adjustment capabilities Removable base for flexible mounting solutions Multiple video inputs supported LY VGA Analog LY DVI I supports either Analog or Digital signal input VGA analog and DVI Digital signal cables included Plug and play capability if supported by your system On Screen Display OSD adjustments in English French German Italian Spanish and Simplified Chinese for ease of set up and screen optimization Software and Reference Library CD includes an information file INF Image Color Matching file ICM and product documentation Energy Saver feature for Energy Star compliance AssetControl Compliant with the following regulated specifications LY EPA ENERGY STAR LY European Union CE Directives User s Guide T Swedish MPR II 1990 d Swedish TCO 99 Installing the Information Files The CD ROM included with this monitor contain
22. tal labelling of personal computers The labelling scheme was developed as a joint effort by the TCO The Swedish Confederation of Professional Employees Svenska Naturskyddsforeningen The Swedish Society for Nature Conservation and Statens Energimyndighet The Swedish National Energy Administration Approval requirements cover a wide range of issues environment ergonomics usability emission of electric and magnetic fields energy consumption and electrical and fire safety The environmental demands impose restrictions on the presence and use of heavy metals brominated and chlorinated flame retardants CFCs freons and chlorinated solvents among other things The product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered to in each country where the company implements its operational policy The energy requirements include a demand that the computer and or display after a certain period of inactivity shall reduce its power consumption to a lower level in one or more stages The length of time to reactivate the computer shall be reasonable for the user 26 User s Guide Agency Regulatory Notices Labelled products must meet strict environmental demands for example in respect of the reduction of electric and magnetic fields physical and visual ergonomics and good usability Below you will find a brief summary of the environmental requirements met
Download Pdf Manuals
Related Search