Hornet Car Security 563T User's Manual
Contents
1. HORNET gt Owner s Guide APPROVED By Mario Escamilla at 11 22 am 9 14 05 For a period of one calendar year from the date of purchase of this auto security device Directed Electronics Inc promises to the ORIGINAL PURCHASER to repair or replace with a comparable reconditioned model free of cost any electronic control module which proves to be defective in workmanship or material under normal use SO LONG AS THE SYSTEM WAS SOLD INSTALLED AND SERVICED BY A PROFES SIONAL AUTO INSTALLER AND REMAINS IN THE CAR IN WHICH THE SYS TEM WAS ORIGINALLY INSTALLED If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the follow ing page After the first calendar year from the date of purchase of this auto security device Directed Electronics Inc promises to the ORIGINAL PURCHASER to repair or replace with a comparable reconditioned model any electronic control module which proves to be defective in workmanship or material under normal use FOR A CHARGE OF 45 00 SO LONG AS THE SYSTEM WAS SOLD INSTALLED AND SERVICED BY A PROFESSIONAL AUTO INSTALLER AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the following page This warranty contains the entire agreement relating to warranty and supersedes all pre vious2. does not start in gear All installations must be performed by an autho rized Directed dealer OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPER ATION OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY YOU MUST IMMEDIATELY CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AUTHO RIZED DIRECTED DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS active arming 10 You can arm the system by pressing of your transmitter for one second When the system arms you will hear a short siren sound or chirp and see the parking lights flash once If the power door locks are controlled by the system the doors will also lock While the system is armed the status LED will flash approximately once per second indicating that the system is actively protecting your vehicle If you hear a second chirp after arming and note that the status LED is flashing in groups see the Diagnostics Section of this guide This extra chirp is called Bypass Notification 2005 directed electronics all rights reserved passive arming The system can be programmed to arm itself automatically called passive arming If the system is programmed for passive arming it will automatically arm 30 seconds after the ignition is turned off and the syst
3. even if the door is immediately closed gt Turning on the ignition key will trip the same progressive re sponse as opening a door gt The optional starter kill prevents the vehicles starter from cranking multi level security arming Multi Level Security Arming allows you to select which of the system s inputs or sensors will be active and which will be bypassed when the system is armed See Table of Zones section of this guide Pressing only in Standard Configuration again within five seconds of arming the system will activate the Multi Level Security feature Each time is pressed again a different security level is selected The different security levels are selected as follows a Press once The siren chirps once The system is armed Press a second time within five seconds The siren chirps twice followed by a long chirp Zone 2 is now bypassed gt Press a third time within five seconds The siren chirps three times followed by a long chirp Zone 4 is now bypassed gt Press a fourth time within five seconds The siren chirps four times followed by a long chirp Zones 2 and 4 are now bypassed 2005 directed electronics all rights reserved gt Press Ala fifth time within five seconds The siren chirps five times followed by a long chirp All input zones except the ignition are now bypassed note Multi Level Security Arming only applies to a sin gle arming cycle Once the syst
4. explanation of all the options available to you Audio Sensor Metal on glass glass cracking and breaking glass produce distinctive acoustic signatures The 506T audio sensor uses a microphone to pick up sounds then analyzes them with proprietary acoustic software to determine if the glass has been struck Backup Battery The 520T keeps the system armed triggers the alarm and keeps the starter interrupt active if main battery is dis connected Hood Lock Prevents the vehicle s hood from being opened without a key keeping thieves away from the system s siren the battery connections and other components under the hood Field Disturbance Sensor An invisible dome of coverage is estab lished by installing the 508D radar sensor Your system can react to any intrusions into this field with the full triggered 2005 directed electronics all rights reserved sequence Power Locks This system offers lock outputs that can control some manufacturers power door lock systems For other systems additional parts may be required Power Trunk Release The accessory output of the system can op erate a factory power release for the vehicle s trunk or hatch Although the on board relay can control most power trunk re leases sometimes an optional relay is required If the factory release is not power activated Directed s 522T trunk release solenoid can often be added Power Window Control Automatic powe
5. if any other shut down zones or the ignition becomes active the timer mode will cancel 1 Press Timer mode buttons 2 The vehicle will confirm with 4 parking light flashes 3 1 second delay will start O 2005 directed electronics all rights reserved 21 4 The system will start the car and will run for the specified duration unless shut down by the remote start button If shut down with the remote start button Ok the system will remain in timer mode 5 The system will start every 3 hours until canceled by the brake hood or neutral safety shut down wires important Timer Mode should be used only in open areas Never start and run the vehicle in an enclosed space such as a garage or carport To exit timer mode turn the ignition switch on any time the engine is running The parking lights will flash 4 times indi cating timer mode has been exited If the system is set up to start in temperature mode the vehicle will start at the specified elapsed time but only if the temperature is less than 0 degrees Fahrenheit note The low temperature start operation will automat ically exit after 18 hours safety features o o This system has several important safety features to ensure proper operation of the motor and prevent accidental damage to the engine or its components 22 2005 directed electronics all rights reserved starter anti grind circuitry Whenever the vehicle is remote
6. on the transmitter or press and release the optional momentary switch Then wait five seconds 2 Turn the ignition key to the OFF position The engine will stay running 3 The engine will run until the pre programmed time elapses or a shut down input is received See the previous Remote Start section for a complete list of shut down inputs note This feature will not work if the brake pedal is being pressed short run turbo 20 Short run turbo mode keeps the engine running after arriving at you destination for a programmable period of 1 3 5 or 10 minutes This allows the system s timer to conveniently cool down the turbo after you have left the vehicle 2005 directed electronics all rights reserved To activate 1 Park the vehicle and set parking brake 2 Remove your foot from the brake pedal and leave the engine running 3 Press and release the and buttons at the same time 4 lights will flash to indicate the remote start has entered short run turbo mode 5 Turn off the key the engine will keep running 6 Exit and secure the vehicle 7 The engine will turn off after the programmed run time timer temperature mode By pressing the remote A and ef buttons the parking lights will flash 4 times and then start the vehicle and run for the set duration in timer mode The remote start can be shut off by the transmitter by pressing the remote start button remain in timer mode but
7. rear defogger output OFE 1 Simultaneously press amp release the buttons on the remote control 2 The lights will flash 2 times 3 The rear defogger output will no longer activate when the vehicle is remote started note If the remote start is on the parking lights will turn off then flash 2 times before returning to their normal output and the defogger output if active will cease To turn the rear defogger output ON 1 Simultaneously press amp release the wx buttons on the remote control 2 The lights will flash 3 times The rear defogger output will once again activate when the vehicle is remote started note If the remote start is on the lights will turn off then flash 3 times before returning to their normal output and the defogger output will activate as programmed note If the temperature is greater than 55 at the time of remote start activation the rear defogger will not acti vate for that start 2005 directed electronics all rights reserved 19 valet take over The Valet Take Over feature allows the vehicle to remain running after the key has been removed from the ignition This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time but would like to leave the motor running and the climate controls on To perform Valet Take Over 1 Before turning off the engine press and release twice within 3 seconds
8. started advanced anti grind circuitry prevents the starter from engaging even if the key is turned to the start position This prevents damage to the starter motor if the key is turned to the start position during remote start operation disabling the remote start system This feature allows your system s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally This feature is useful if the vehicle is being serviced or stored in an enclosed area To disable the remote start move the shutdown toggle switch to the OFF position The switch can be installed in a location of your choice Check with your installer for recommended locations Location of Shutdown Switch over and under rev protection The system monitors the engine speed and will automatically shut the engine off if the RPMs rise above or fall below the programmed levels This feature prevents damage to the motor due to fuel delivery system failures or other problems which may cause the engine to race note The system uses a wire connected to the vehicle to sense engine speed This wire must be connected in order for over and under rev protection to work O 2005 directed electronics all rights reserved 23 shut down inputs This security system uses several inputs to shut down the remote start operation of the motor or prevent remote start if certain inputs are active The two most important are hood and brake in
9. A 92081 www directed com 2005 Directed Electronics All rights reserved G563T 09 05
10. AREA ADJACENT TO THE VEHICLE ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED These precautions are the sole respon sibility of the user gt Use of this product in a manner contrary to its intended mode of operation may result in property damage personal injury or death 1 Never remotely start the vehicle with the vehicle in gear and 2 Never remotely start the vehicle with the keys in the ignition The user must also have the neutral safety feature of the vehicle periodically checked wherein the vehicle must not remotely start while the car is in gear This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in the product installation guide If the vehicle starts in gear cease remote start operation immediately and consult with the authorized Directed dealer to fix the problem gt After the remote start module has been installed contact your authorized dealer to have him or her test the remote start module by performing the Safety Check outlined in the product installation guide If the vehicle starts when performing the Neutral Safety Shutdown Circuit test the 2005 directed electronics all rights reserved 9 remote start unit has not been properly installed The remote start module must be removed or the installer must properly reinstall the remote start system so that the vehicle
11. Buttons The short run turbo mode is activated when these buttons are pressed simultaneously O 2005 directed electronics all rights reserved 7 and and Buttons When simultaneously pressed these buttons control the rear window defogger during remote starting and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously The auxiliary output controls using your system warning safety first The following safety warnings must be observed at all times gt Due to the complexity of this system installation of this product must only be performed by an authorized Directed dealer gt When properly installed this system can start the vehicle via a command signal from the remote control transmitter Therefore never operate the system in an enclosed area or partially enclosed area without ventilation such as a garage When parking in an enclosed or partially enclosed area or when having the vehicle serviced the remote start system must be disabled using the installed toggle switch It is the user s sole responsibility to properly handle and keep out of 8 2005 directed electronics all rights reserved reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING
12. Bypass Notification chirp Once the light turns off however the security system resumes normal monitoring note Bypass Notification does not occur when the sys tem is in Silent Mode or if the notification chirps have been programmed off by the installer disarming diagnostics Extra chirps that are heard when disarming the system are the Tamper Alert If four chirps are heard when disarming the system then the security system was triggered in your absence If five chirps are heard when disarming the system a zone was trig gered so many times that the Nuisance Protection Circuitry has bypassed that zone In either case the status LED will indicate which zone was involved see Table of Zones section The secu rity system will retain this information in its memory and chirp four or five times each time it is disarmed until the next time that the ignition is turned on system status chirps The siren will chirp when arming disarming the system The pattern of chirps will audibly report the system s status as described below O 2005 directed electronics all rights reserved Action Arm Arm Disarm Disarm Disarm Number of Chirps Description 1 System armed 1 3 second delay 1 System armed with Bypass Notification 2 System disarmed 4 System disarmed with Tamper Alert 5 System disarmed NPC active table of zones A zone is represented by the number of LED flashes used by the system to identi
13. STREAM OF COMMERCE THEREWITH THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLUSION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND OR ANY AND ALL WAR RANTY OF FITNESS FOR A PARTICULAR PURPOSE AND OR ANY AND ALL WARRANTY OF NON INFRINGEMENT OF PATENTS IN THE UNITED STATES OF AMERICA AND OR ABROAD NEITHER THE MANUFACTURER OR ANY ENTITIES CONNECTED THEREWITH SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMIT ED TO ANY CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES TOW ING REPAIR REPLACEMENT DAMAGES FOR LOSS OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON TROL MODULE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or con sequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state IMPORTANT NOTE This product warranty is automatically void if its date code or serial number is defaced missing or altered This warranty will not be valid unless you have completed the war ranty card and mailed it to Directed Electronics Inc within 10 days after purchase to the address listed on the warranty registration card Make sure you have all of the following information from your dealer A clear copy of the sales re
14. and contemporaneous representations or understandings whether written or oral IN ANY EVENT DIRECTED ELECTRONICS INC IS NOT LIABLE FOR THE THEFT OF THE VEHICLE AND OR ITS CONTENTS This warranty is void if the product has been damaged by accident unreasonable use neglect improper service or other causes not arising out of defects in materials or construction This warranty is non transferable and does not apply to any unit that has been modified or used in a manner contrary to its intended purpose and does not cover batteries The unit in question must be returned to the manufacturer postage prepaid This warranty does not cover labor costs for the removal diagnosis troubleshooting or reinstallation of the unit For service on an out of warranty product a flat rate fee by model is charged Contact your authorized deal er to obtain the service charge for your unit These systems are a deterrent against possible theft Directed Electronics Inc is not offer ing a guarantee or insuring against the theft of the automobile or its contents and dis claims any liability for the theft of the vehicle and or its contents Directed Electronics does not authorize any person to create for it any other obligation or liability in connec tion with this security system 2005 directed electronics all rights reserved i TO THE MAXIMUM EXTENT ALLOWED BY LAW ANY AND ALL WAR RANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE
15. be disabled To start the car it will be necessary to disarm the system with the trans mitter lt is also possible to disarm the AED feature by turning the ignition key to the RUN position and pressing the Valet button the programmed number of times AED is also disabled when the system is in Valet mode gt Siren tones and chirp volume The output of the Revenger Soft Chirp siren consists of six different tones in sequence Any of these tones can be eliminated by a dealer resulting in a unique easily identifiable siren sound The chirps can be either full volume or 6 decibels quieter than the full alarm blast gt 12 24 or 60 minute run time your system can be programmed to allow the vehicle to run for 12 24 or 60 minutes when remote started Can be set up to minute increments by your installer gt 3 6 9 or 12 minute timer mode run time Your system can be programmed to allow the vehicle to run for 3 6 9 or 12 minutes when remote started in timer mode Can be set up to 16 minutes by your installer 2005 directed electronics all rights reserved 33 34 gt While the remote start system is running the engine the parking lights of the vehicle can flash on and off or come on and light steadily gt Comfort closure is a programming option which closes the vehicle s windows after remote locking Listed below are some of the many expansion options available Please consult your dealer for a complete
16. cA Sie a 16 EMOTE A SS CA eR ae 17 rear defogger errot E GPG E E MOT AES 19 VAC TAKEOVER has enar Cie pa ra a Te ets O 20 Short ER boss sd da ds ta ada ia 20 timer temperature INOUE AE AAA 21 safety features AO 22 starter anti grind CCI Ve A e is at 23 disabling the remote start 23 over and under Proteo ie 23 Shutdown INDUIS td do A rte 24 nuisance prevention 24 diagnostics ses E SS A E EA E 25 arming diagnostics avi da anak ee MGA bare ws had Saeed a thew tan 25 disarming CIAO OSES ine ar das 26 o y s ek O 26 table OF ZONES sedate adh ates ce ad eke 27 interpreting zone diagnostics aia al Ea Dore os 28 code HOPPER AO ER AG SNe 28 O 2005 directed electronics all rights reserved 1 high frequent a A eA A ns 29 Ower LECORMMNON A IAN aes E 29 rapid resume los ios y totes 30 power saver mode icant OO programming options 31 security amp convenience expansions 34 glossary of terms ia AA AAA AAA raa ea 36 2 2005 directed electronics all rights reserved A controls the Arm and Panic On Off function Ej controls the Disarm and Panic Off function c
17. ceipt showing the following Date of purchase Your full name and address Authorized dealer s company name and address Type of alarm installed Year make model and color of the automobile Automobile license number Vehicle identification number All security options installed on automobile Installation receipts 2005 directed electronics all rights reserved table of contents limited lifetime consumer warranty i standard transmitter configuration 3 Whats included ins A ste ne E Bead Go 4 important informations 66 45 a Wee retirer rs 4 System MAINTENANCE fo sad eat ot ADA Sed ex eee das 5 yo r Waranty EM hee ees Soe oa hea 5 TEEN HOMES LEI ASA EAS ESAS mia de 5 CAUTION A ARAS IBAS AS AE A eed as 6 transmitter MUNCHONS ci A A AA A 6 standard con ena Nan die al 6 your A A 8 A A 8 A awe eMedia nate 10 Passive plane Mad dae 11 multi level security arming DAS uen AAA 12 arming is EA ARAS AA 13 A A ee 13 A reds Gay 14 disarming without a transmitter devise SAA 14 silent modes ies ii A aa a a e a da 15 pame modereren SS widens AAA CS 16 valet mode gr Kaew M
18. e system remains in Valet Mode the LED will come back on the next time the ignition is turned on and then back off Programming options control your system s normal operational set up Most options do not require additional parts but some may require installation labor The following is a list of the programmable options with the factory settings in Bold gt Active arming transmitter only or passive arming auto matic arming 30 seconds after the last door has been closed gt Arming disarming siren chirps on or off gt The ignition controlled door lock feature on or off When this feature is programmed on the doors will lock three seconds after the ignition is turned on and unlock when the ignition is turned off If your installer is programming the security system with the Directed Bitwriter ignition lock and unlock are independent features that can be programmed separately Passive door locking with passive arming or active door locking only when arming with the transmitter Passive locking allows the vehicle s doors to lock when the security 2005 directed electronics all rights reserved 31 32 system passively arms after the 30 second countdown This feature only works if passive arming has been programmed Panic mode enabled disabled when the ignition is turned on Some states have laws against sirens sounding in moving cars Forced passive arming on or off If your security
19. em detects that you have left the vehicle by opening and closing a door Whenever the system is in its 30 second passive arming countdown the status LED will flash twice as fast as it does when the system is armed At the 20 second point of the count down the siren will chirp to indicate that the system is about to arm At the 30 second point the parking lights will flash to indicate that the system is armed note If any protected entry point such as a door or a switch protected trunk or hood is open the system will not passively arm unless forced passive arming is pro grammed on See Programming Options section When armed your vehicle is protected as follows gt Light impacts trigger the Warn Away signal When trig gered the siren chirps and the parking lights flash for a few seconds gt Heavy impacts trip a Triggered Sequence The sequence consists of the siren sounding continuously and the parking lights flashing for a pre programmed period which can range in duration from 1 to 180 seconds gt If a door is opened the system will immediately start chirping the siren and flashing the parking lights Three seconds later the siren output changes to a continuous blast O 2005 directed electronics all rights reserved 11 This progressive response gives you time to disarm the sys tem with your transmitter if you inadvertently open the door while the system is armed while still providing instant re sponse
20. em is disarmed and then re armed all the zones will be active again arming while driving Your security system can be armed while driving the vehicle Simply press on the transmitter for two seconds while the vehicle is running The siren will chirp once to indicate that the security system is armed and then once more to indicate that the ignition is on The system will not respond to any input except the door triggers and the starter kill relay if installed will not be activated Once you have arrived at your destination the system will disarm when the ignition is turned off The siren will chirp twice and the LED will then stop flashing The system can also be disarmed at any time by pressing disarming To disarm the security system press dl You will hear two chirps and the parking lights will flash twice If the power locks are controlled by the system the doors will also unlock The siren chirping either four or five times when disarming indicates Tamper Alert which is described in the Diagnostics Section of this guide O 2005 directed electronics all rights reserved 13 14 high security disarm This security system offers High Security Disarm High Security Disarm is a feature that makes it possible to silence and reset the system while it is triggering without disarming the system If the system is triggered and the siren has been sounding for longer than six seconds pressing on the remote transmitter will st
21. exit Valet Mode Turn the ignition on 1 2 Turn the ignition off 3 3 Press and release the Valet DRW 121 9 No button within 10 seconds The status LED will light solidly if you are entering Valet Mode and it will go out if you are exiting Valet Mode To enter or exit Valet Mode using the transmitter 1 Open any vehicle door 2 Press 2005 directed electronics all rights reserved 3 Press ma 4 Press again The status LED will light solidly if you are entering Valet Mode and it will go out if you are exiting Valet Mode remote start This feature allows you to remotely start and run your vehicle for a programmable period of time This makes it possible to warm up the engine as well as adjust the interior temperature of the ve hicle with the climate control system If interior heating or cooling is desired the climate controls must be preset and the fan blower must be set to the desired level prior to remote starting the vehicle important 1 Never remote start your vehicle when the keys are in the ignition except when performing Valet Take Over and 2 Never start the vehicle 1f it is not in either PARK or NEUTRAL To remote start the vehicle 1 Press on the transmitter twice within 3 seconds 2 The parking lights will flash to confirm that the vehicle will attempt to start 3 In gasoline vehicles the engine will start 4 seconds after the parking lights flash In die
22. fy a particular type of input Standard input assignments are listed in the following table along with spaces to write in any optional sensors or switches that have been installed ZONE Number of LED Flashes 1 2 DEALER INSTALLED DESCRIPTION OPTIONS Trunk Pin Instant trigger a heavier impact detected by the shock sensor Door switch trigger Instant trigger for optional sensors Ignition trigger Hood Pin 2005 directed electronics all rights reserved 27 interpreting zone diagnostics Warn Away responses are not reported by arming or disarming diagnostics If you receive a Bypass notification when arming or a Tamper Alert notification when disarming look at the LED Active or triggered zones will be indicated by a pattern of blinks by the LED Example If zone 3 was active or triggered the LED will blink three times with a two second pause Then it will blink three times again and repeat until the ignition is turned on note Your system stores the last two triggered zones in memory If your system has been triggered but the LED has been reset by turning on the ignition your dealer can still recall the last two zones that were triggered Contact your dealer for details code hopping 28 The receiver and transmitters use a mathematical formula called an algorithm to change their code each time the transmitter is used This technology has been developed to increase the secu
23. m battery that will last approximately one year under normal use When the battery begins to weaken operating range will be reduced and the LED on the remote will dim your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase Your product warranty will not be validated if your warranty registration is not returned Make sure you receive the warranty registration from your dealer It is also necessary to keep your proof of purchase which reflects that the product was installed by an authorized dealer fec id notice This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesirable operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device 2005 directed electronics all rights reserved 5 caution This product is designed for fuel injected automatic transmis sion vehicles only Use of this product in a standard transmission vehicle is dangerous and contrary the product s intended use f The receiver uses computer based Learn Routine to learn the transmitter buttons This makes it possible to assign any remote transmitter button to any receiver function The transmi
24. n the vehicle and designed to pick up impacts to the vehicle or glass Transmitter A hand held remote control which operates the various functions of your system O 2005 directed electronics all rights reserved Trigger or Triggered Sequence This is what happens when the alarm goes off or trips The triggered sequence of your system consists of the siren sounding and parking lights flashing for the programmed duration Valet button A small push button mounted at a discretionary location inside the vehicle It is used to override the starter inter rupt when a transmitter is lost or damaged or to enter or exit Valet Mode Warning Zone Response Lighter impacts to the vehicle will generate the Warning Zone response It consists of several seconds of siren chirps and parking light flashes Zone A zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone Often two or more inputs may share the same zone 2005 directed electronics all rights reserved 37 38 O 2005 directed electronics all rights reserved Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet A e P lt QUICK REFERENCE GUIDE Arming To arm press EY When the system arms you will hear a short chirp and the parking lights will flash once Arming while driving arm the system while driving press on you
25. ontrols Silent Mode and Auxiliary channel 2 output AUX and pressed together control Turbo Short Run A and pressed together control channel 4 output N and pressed together control channel 5 output and and pressed together control the rear defogger 2005 directed electronics all rights reserved 3 and pressed together control channel 6 output A control module An HX receiver antenna Two four button transmitters A Stinger DoubleGuard two stage shock sensor A Revenger Soft Chirp six tone programmable siren A status LED indicator light A push button Valet button Your warranty registration VV VV VV A shut down toggle switch Congratulations on the purchase of your combination remote start alarm system Due to the complexity of this system it must be installed by an authorized dealer only Installation of this product by anyone other than an authorized dealer voids the warranty All dealers are provided with a preprinted dealer certifi cate to verify authorization By carefully reading this Owner s Guide prior to using your system you will maximize the use of this system and its features You can print additional or replacement copies of this manual by accessing our web site at www directed com 4 2005 directed electronics all rights reserved system maintenance The system requires no specific maintenance Your remote is powered by a small lightweight 3 volt lithiu
26. op the trigger and return the unit to the armed state The system will not disarm but rather reset This prevents you from disabling the system should you wish to disarm it without visu ally checking the vehicle Pressing after resetting the system will disarm the system pressing this button during the first six seconds of the triggered sequence will disarm the security system immediately The six second timer is provided for your conve nience in case the system is accidentally triggered disarming without a transmitter If your remote transmitter is lost or damaged you can manually disarm your vehicle security system To disarm the system without a transmitter you must have the vehicle s ignition key and know where the Valet switch is located Be sure to check with your installer at the time of installation for both the location and the preset response 1 5 presses of the Valet switch 2005 directed electronics all rights reserved To disarm the security system turn the ignition to the ON posi tion Press the Valet button the preset number of times one to five times within 15 seconds After five seconds the system will disarm If the system does not disarm you may have waited too long turn the ignition off and on and try again Location of Valet Button Number of Presses important The Valet button can be programmed to respond to 1 5 presses for the disarm function You must check with the installe
27. puts The hood input will prevent the motor from starting as well as shut it down any time the hood is opened The brake pedal will shut down the motor at any time during remote start operation as well as preventing the remote start from activating while it is being pressed nuisance prevention circuitry 24 Your system has Directed s Nuisance Prevention Circuitry NPC It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder jackhammers airport noise etc Example If the alarm triggers three times within a 60 minute period and each time the same sensor or switch triggers the alarm NPC will interpret those triggers as false alarms After the third trigger NPC ignores or bypasses that sensor or switch along with any other sensors or switches sharing the same zone for 60 minutes If the bypassed sensor tries to trigger the security system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that is continually being triggered will remain bypassed 2005 directed electronics all rights reserved The vehicle doors are protected by NPC differently If your secu rity system is triggered by an open door for three full cycles the system will bypass the doors until the trigger ceases note Arming and disarming the system does not reset this function The only ways to reset a bypassed zone are fo
28. r it to not trigger for 60 minutes or to turn on the igni tion If testing your system it is important to remember that the NPC programming can cause zones to be bypassed and appear to stop working If five chirps are heard when disarming NPC has been engaged If you wish to clear the NPC memory turn the ignition on The microprocessor at the heart of your system is constantly monitoring all of the switches and sensors connected to it It is designed to detect any faulty switches and sensors and prevents them from disabling the entire system The microprocessor will also record and report any triggers that occurred during your absence Refer to the System Status Chirps and Table of Zones sections of this guide for diagnostic information arming diagnostics If the security system is armed at the same time that an input is active such as a door opening or sensor triggering you will hear one siren chirp to indicate arming and a second siren chirp to indicate Bypass Notification Bypass Notification chirp means that the security system ignores the input that was active when 2005 directed electronics all rights reserved 25 26 the system was armed until that input ceases Three seconds after that input ceases the security system will resume normal moni toring For example if your vehicle has an interior light exit delay and you arm your security system before the interior light turns off you may hear a second
29. r to verify the programming for your individual unit silent mode To temporarily turn off the arm or disarm chirps use Silent Mode Simply press for less than one second before arming or disarming and the confirmation chirp s will be elim inated for that one operation only If you want the arm disarm chirps turned off permanently your dealer can do this for you note The Warn Away response to lighter impacts is bypassed if the system is armed using Silent Mode This ensures that no chirps will be emitted by the siren in an area you want chirp free The system is still fully capable of triggering Only the Warn Away response is bypassed 2005 directed electronics all rights reserved 15 panic mode If you are threatened in or near your vehicle you can attract attention by triggering the system with your transmitter Just press for two seconds and you will enter Panic Mode The siren will sound and the parking lights will flash for the programmed siren duration To stop Panic Mode at any time press on the remote transmitter again valet mode 16 You can prevent your security system from automatically arming and triggering by using Valet Mode This is very useful when washing the vehicle or having it serviced In Valet Mode the security system will not arm even with the remote transmitter but all convenience functions door locks trunk release etc will continue to work normally To enter or
30. r transmitter while the vehicle is running The system will chirp once and then once more to indi cate that the ignition is on Disarming To disarm press You will hear two chirps and the parking lights will flash twice High security disarm For high security disarm press on your transmitter and the siren will stop sounding To completely disarm the security system press again and the system will chirp 4 or 5 times reporting the trigger Disarming without a transmitter Turn on the ignition Press the Valet button within 15 seconds The system should now disarm If it does not you may have waited too long so turn the ignition off and on and try again Silent Mode Pressing briefly before arming or disarming will eliminate the confirma tion chirp s for that one operation only Panic Mode Press for 2 seconds and you will enter Panic Mode The siren will sound and the lights will flash for 30 seconds stop Panic Mode at any time press on the transmitter again To remote start the vehicle twice within 3 seconds The parking lights will turn on if connected and the vehicle will start and run for the programmed period of time To disable the remote start system To disable the remote start move the shutdown toggle switch to the OFF position Location of Valet button Number of Valet button pulses for disarming O 2005 directed electronics all rights reserved 39 Valet Takeo
31. r window control is pro vided with the 529T and 530T systems These can operate power windows and can roll them up automatically when the system is armed roll them down or both up and down Mobile Video This system is compatible with Directed Videos MCB1000 Multi Channel Controller featuring on screen secu rity system programming and zone trigger information 2005 directed electronics all rights reserved 35 glossary of terms 36 Control Unit The brain of your system Usually hidden under neath the dash area of the vehicle The control unit houses the microprocessor which monitors your vehicle and controls all system functions Fault Proof Starter Interrupt An automatic switch controlled by your system that prevents the vehicle s starter from cranking whenever the system is armed The vehicle is never prevented from cranking when the system is disarmed in Valet Mode or if the starter interrupt switch itself fails Your system has feature ready circuitry for the starter interrupt however installation may require additional labor Input A physical connection to the system input can be provided by a sensor pinswitch or by existing systems in the vehicle such as ignition or courtesy lights LED A red light mounted at a discretionary location inside the vehicle It is used to indicate the status of your system Shock Sensor This system has a dual zone shock sensor This sensor is mounted i
32. rity of the unit The control unit knows what the next codes should be This helps to keep the transmitter in sync with the control unit even if you use the remote control out of range of the vehicle However if the remote has been pressed many times out of range of the vehicle or the battery has been removed it may fall 2005 directed electronics all rights reserved out of sync with the control unit and fail to operate the system a To re sync the remote simply press several times within range of the vehicle The alarm will automatically re sync and respond to the transmitters normally high frequency Your system transmits and receives at 434 MHz This provides a cleaner spectrum with less interference and a more stable signal Enjoy a phenomenal increase in range even in areas with high radio interference owner recognition Owner Recognition is a revolutionary new feature available only from Directed Using a Directed Bitwriter hand held program ming tool your dealer can program many of the system settings The programmer makes it possible to program different settings for each transmitter that is used with the system Then whenev er a specific transmitter is used the system will recall the settings assigned to that transmitter Owner Recognition lets up to four users of the system have different settings that meet their specific needs It is almost like having four separate alarms in
33. sel vehicles the engine will start when the WAIT TO START indicator on the vehicle s dash goes out or the programmed delay has ended O 2005 directed electronics all rights reserved 17 18 4 Once the vehicle has started it will run for the pre program med period of time either 12 24 or 60 minutes see Programming Options section of this guide or until a shut down input is triggered important lt is unsafe to operate a vehicle s motor in a garage or other closed off area Breathing the exhaust from the vehicle is hazardous to your health Never acti vate the remote start in an enclosed space When you are ready to drive the vehicle 1 Insert the ignition key and turn it to the ON not START posi tion 2 Press the brake pedal OFF 2 note If the brake pedal is pressed before the key is in the ON position the engine will shut down While the vehicle is running during remote start operation the system will monitor the vehicle and will automatically shut down the engine if the system receives any of the following shut down inputs gt The brake pedal is pressed gt The hood is opened gt The shutdown toggle switch is put into the OFF position gt The pre programmed run time 12 24 60 minutes has elapsed gt Transmitter buttons is pressed twice within 3 seconds O 2005 directed electronics all rights reserved rear defogger To turn the
34. system is programmed for passive arming and the forced passive arming feature has been programmed on the system will passively arm after one hour even if a protected entry has been left open Forced passive arming ensures that the system will be armed if a door has accidentally been left ajar when leaving the vehicle note When the system passively arms after one hour the entry point that has been left open and anything con nected to the same zone is bypassed and cannot trigger the system However the remaining inputs to the system are fully operational Full trigger response 30 or 60 seconds This determines how long the full triggered sequence lasts Some states have laws regulating how long a security system can sound before it is considered a nuisance If your installer is programming the security system with the Directed Bitwriter the full trig gered response can be programmed for any duration ranging from 1 to 180 seconds Automatic Engine Disable AED on or off The purpose of this feature is to protect the vehicle from being stolen at all times regardless of whether or not the alarm is armed If 2005 directed electronics all rights reserved AED is programmed on the starter of the vehicle will be disabled 30 seconds after the ignition is turned off Once the key is turned off the LED will flash slowly one half its normal armed rate to indicate the AED arming cycle Thirty seconds later the starter will
35. tter initially comes programmed with Standard Configuration but may also be customized by an authorized dealer The buttons in all of the instructions in this manual correspond to a Standard Configuration transmitter standard configuration Button The arming and panic functions are controlled by pressing this button for one second Button The disarming function is controlled by pressing this button for one second Button Silent Mode and an optional auxiliary function are controlled by this button Silent Mode works by pressing this button for 6 2005 directed electronics all rights reserved less than one second before arming or disarming An optional auxiliary function such as trunk release can be controlled by pressing this button for 1 5 seconds The auxiliary output controls Button The remote start function of your system is controlled by pressing this button twice within 3 seconds and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously The auxiliary output controls and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously The auxiliary output controls and Buttons The remote start timer mode is controlled by pressing these buttons simultaneously
36. ver M Press and release on the transmitter twice in 3 seconds Turn the ignition key to the OFF position Once the vehicle has started will run for the pre programmed period of time 12 24 or 60 minutes Rear Window Defogger Press the A buttons simultaneously to turn the defogger on or off when remote starting When a remote start is initi ated the parking lights will flash 2 times if the defogger 15 set to off and will flash 3 times if the defogger is set to on Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet P DO 40 O 2005 directed electronics all rights reserved The company behind this system is Directed Electronics Since its inception Directed Electronics has had one purpose to provide consumers with the finest vehicle security and car stereo products and accessories available The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology Directed is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world Call 800 274 0200 for more information about our products and services Directed Electronics is committed to delivering world class quality products and services that excite and delight our customers VDiirected ELECTRONICS Vista C
37. your vehicle one for each user 2005 directed electronics all rights reserved 29 note Owner Recognition cannot programmed with out a Bitwriter and the necessary software Check with your dealer for more information id resume logi This Directed system will store its current state to non volatile memory If power is lost and then reconnected the system will recall the stored state from memory This means if the unit is in Valet Mode and the battery is disconnected for any reason such as servicing the car when the battery is reconnected the unit will still be in Valet Mode This applies to all states of the system including arm disarm and Valet Mode power saver mode _ _________ 30 Your system will automatically enter Power Saver Mode while armed or in Valet Mode after a period of time in which no oper ation has been performed This lowers the current draw on the vehicle s battery Power Saver Mode takes over under the following conditions gt Power Saver when the system is armed After the system has been armed for 24 hours the LED will flash at half its normal rate decreasing the system s current draw gt Power Saver in Valet Mode When the system enters Valet 2005 directed electronics all rights reserved Mode the LED illuminates steadily If the vehicle is not used ignition is not turned on for a one hour period while the system is in Valet Mode the LED will shut off If th
Download Pdf Manuals
Related Search