Hoover U5361950 User's Manual
Contents
1. Bend filter to open pleats Lay filter on top of pre filter Make sure T f filt til dust particles all filter pleats are inside the edges of eee cine aaa tiee EUSEPANN the pre filter Press on filter gasket F l until 4 tabs G 2 on either side of filter Do not tap the soft pleated part of the are set in the slots H on the pre filter ilter he filter l Mier Iicould camege tne tige Be careful not to press the filter gasket below the pre filter edge Slide pre filter assembly all the way to Replace dirt cup bottom of cup Pivot pre filter assembly and snap in place Replace dirt cup lid If lid will not close completely the pre filter assembly is not positioned correctly Secondary and final filters gt gt CE I SSS GA Gi GG A YW ZZ A GA Vy 27 4G Yy YH a Cleaning secondary filter Disconnect cleaner from electrical outlet The secondary filter G located under neath the retainer in the bottom of clean er cavity protects the motor from dirt particles If filter becomes dirty remove dirt cup Fig 3 2 Remove screw and pull retainer out Lift out filter Hand wash filter in cold water with mild detergent then air dry Reposition dry filter retainer and screw Replace dirt cup Should you want to replace this filter ask for HOOVER part No 38765019 Cleaning final filter The final filter assists in returning clean air to2. Fig 1 8 and 1 9 2 Clear out hose 13 3 Look into D and remove block age 5 Check connection at hose tube C remove any blockage Checking under bottom plate 6 Turn cleaner OFF and unplug 7 Remove bottom plate belt and agita tor see The belt section Look into opening E for blockages and remove 8 Remove agitator shield see Fig 3 21 and remove any loose debris which may have accumulated under it 14 Full One Year arrani Domestic Use Your HOOVER appliance is warranted in normal household use in accordance with the Owner s Manual against original defects in material and workmanship for a period of one full year from date of purchase This warranty provides at no cost to you all labor and parts to place this appliance in correct operating condition during the warranted period This warranty applies when the appliance is purchased in the United States including its territories and possessions or in Canada or from a U S Military Exchange Appliances purchased elsewhere are covered by a limited one year warranty which covers the cost of parts only This warranty does not apply if the appliance is used in a commercial or rental application Warranty service can only be obtained by presenting the appliance to one of the following Authorized Warranty Service outlets Proof of purchase will be required before service is rendered 1 Hoover Factory Service Centers 2 H
3. section Service To obtain approved HOOVER service and genuine HOOVER parts locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot by echecking the Yellow Pages under Vacuum Cleaners Household OR e checking the list of Factory Service Centers provided with this cleaner OR echecking the Service section of The Hoover Company on line at www hoover com OR e calling 1 800 944 9200 for an automated referral of authorized service outlet locations U S only Do not send your cleaner to The Hoover Company in North Canton for service this will only result in delay If further assistance is needed contact The Hoover Company Consumer Response Center North Canton Ohio 44720 Phone 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376 Always identify your cleaner by the complete model number when requesting information or ordering parts The model number appears on the bottom of the cleaner Hoover cleaning performance This Hoover Cleaning Performance Sys tem is for comparing the relative pro gressive performance of Hoover uprights only and not for comparison with any other brands The majority of this rating is based upon the ASTM International Carpet Cleaning Effective ness Test ASTM Test F608 Other per formance factors include Hose Power ASTM Test F558 Surface Litter Clean ing Hard Floor
4. tone 8485 900 120V 60Hz 120A Y BELT 38528 033 LO USE ONLY IGARERO BOLAMENTE POUR UN USAGE MENAIER UNIQUEMENT nRT h Carton Ohio 48729 LR baa y SE U A Fabrio aux U Important Safeguards When using an electrical appliance always follow basic precautions including the following READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE a a Warn ng m To reduce the risk of fire electric shock or injury Do not use outdoors or on wet surfaces e Close supervision is necessary when any appliance is used by or near children Do not allow vacuum cleaner to be used as a toy or to run unattended at any time e Keep hair loose clothing fingers feet and all parts of body away from openings rotating agitator and other moving parts Do not operate cleaner in bare feet or when wearing open toe shoes or sandals Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use to pick up flammable or combustible materials such as gasoline or fine wood sandings or use in areas where they may be present Avoid picking up hard sharp objects with the cleaner They may damage the cleaner Always turn off this appliance before connecting or disconnecting hose Do not use without dirt cup or filters in place Empty dirt cup and clean filters fre quently when picking up very fine materials such as powder e Use extra care when cleaning on stairs Do not put any o
5. Cleaning Edge Clean ing Cleaning Width and Air Filtration problem If a minor problem occurs it usually can be solved quite easily when the cause is found by using the check list below Problem Cleaner won t run Possible cause Possible solution e Not firmly plugged in Plug unit in firmly No voltage in wall plug e Check fuse or breaker Blown fuse or tripped breaker e Replace fuse or reset breaker Thermal protector activated e Allow cleaner to cool for 30 minutes this will reset the thermal protector see pg 12 Problem Cleaner won t pick up Possible cause Possible solution e Broken or worn belt e Replace belt e Agitator brush roll worn Replace brush roll e Dirt cup full e Empty cup Incorrect carpet height setting Move nozzle control knob to lower setting Blockage in air flow passage e Clear blockage e Main filter clogged e Clean main filter by either tapping the side of the dirt cup or removing the filter as described in the Filter assembly section Pre filter clogged e Clean pre filter as described in Filter assembly section Dirt cup not properly installed e Position dirt cup properly and snap in place Fig 3 4 Dirt cup lid not positioned properly or missing Ensure that dirt cup lid is properly positioned Filter assembly not installed properly e Ensure that pre filter assembly and main filter are positioned properly
6. Figs 3 9 to 3 10 Problem Cleaner hard to push Possible cause Possible solution Incorrect carpet height setting Move nozzle control knob to a higher setting Problem Cleaning tools won t pick up Possible cause Possible solution Dirt cup not properly installed e Position dirt cup properly and snap in place Fig 3 4 e Blockage in hose e Clear blockage Problem Visible dirt leaking through final filter Possible cause Possible solution Filter assembly not installed properly e Ensure that pre filter assembly and main filter are positioned properly Clearing blockages Disconnect cleaner from electrical outlet Low suction or pick up may be due to a blockage in the system Refer to the fol lowing steps to check for blockages continuing with each step until the blockage is found Turn cleaner OFF and disconnect from electrical outlet 1 Check fullness of dirt cup and filter assembly empty cup and clean filters if needed D ANNDAN r Z 7 7 7 Z 7 4 7 77 7 Y Check dirt duct 2 Remove dirt cup look in duct A 3 Clear blockage from dirt duct Check airflow path 4 Plug cleaner in and turn ON Check for suction at end of hose B a If there is suction continue with step 5 b If there is no suction check for blockage in hose and dirt tube as follows 1 Disconnect hose from dirt duct D by reversing procedure for Attach hose
7. To turn cleaner OFF push toward back of cleaner marking furniture 12 Final filter exhaust voltage specified on data plate on bottom of cleaner This cleaner is intended for household use Handle positions The handle of your cleaner has three positions upright for storage and when using cleaning tools operating posi tion for general operation on carpet and floors low for reaching under low furniture Step on handle release lever to lower handle Continued 2 5 i UNIA Transporting cleaner Put handle in upright position Tilt cleaner back on rear wheels Push forward Carrying handle Use the carrying handle to lift the cleaner Carpet height adjustment The cleaning of carpet and rugs takes place at the nozzle A When it is necessary to raise and lower the nozzle for various carpet pile heights slide the nozzle control knob B to the desired setting Handie position For ease in sliding knob place handle in the upright position C The nozzle will not move into the adjusted position until the cleaner handle is lowered to the operating position D Settings For maximum cleaning performance the following carpet height settings are recommended e Lowest setting for all types of carpet and hard floors Note If the cleaner is difficult to push slide knob to the next higher setting Higher settings for very deep pile carpet where easier pushing effort
8. is desired while maintaining good cleaning performance Cleaning lightweight flexible rugs Stand on one end of rug and move cleaner toward other end or edge Before reaching edge push down on handle This will lift up the nozzle front of cleaner as shown and will prevent rug from clinging to cleaner Continue to lift up nozzle so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower nozzle and use only for ward strokes Edge cleaning Edge cleaning is provided on both sides of the nozzle to remove dirt in carpet near baseboards and furniture Guide either side of nozzle parallel to edge of carpet or furniture Stair cleaning A stair cleaning handle has been designed for ease in using your cleaner on stairs With handle in operating posi tion place fingers under edge of stair cleaning handle and guide cleaner with other hand on upper handle As an alternative you may use the hose and furniture nozzle for stair cleaning Clean from bottom to top When using cleaning tools the agita tor will continue to rotate CAUTION To avoid personal injury or unnecessary wear to carpet and to prevent the cleaner from falling always place it at the bottom of the stairs Cleaning tools Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas The cleaner is ready for tool use when handle is in upright positi
9. its belt guide N Secure agitator Replace bottom plate Grasp agitator firmly and fit it into posi Reposition bottom plate and 4 Phillips tion by first sliding end opposite the belt head screws Tighten screws securely into the rectangular slot O on side of cleaner Pull other side of agitator P into place Turn agitator making sure belt is not pinched between agitator and agitator shield Continued 2 11 The agitator brush roll When to replace When agitator brushes are worn the agitator should be replaced To check condition of brushes discon nect cleaner from electrical outlet Move edge of a card across bottom plate while turning agitator To maintain cleaning effectiveness replace agitator if brushes do not touch card What to buy Your cleaner requires either a 13 or 15 agitator When purchasing a new agita tor ask for one of the following 13 HOOVER part No 48414110 15 HOOVER part No 48414115 How to replace Disconnect cleaner from electrical outlet Remove bottom plate belt and agitator following directions in The belt section beginning with Fig 3 18 Discard old agitator Continue following the directions in The belt section to reposition belt new agitator and bottom plate Edge groomer replacement When to replace The edge groomers located on both sides of the nozzle should be replaced when they are worn What to buy When purchasing ed
10. the room To remove this filter when it becomes dirty remove dirt cup and pull down top of filter Removing and replacing filter Lift out filter H and hand wash it in cold water with mild detergent Let filter air dry and reposition it on the side of cleaner Reposition dirt cup Should you want to replace this filter ask for HOOVER part No 43613026 Do not operate cleaner without any of the filters in place Check agitator shield Because your cleaner picks up so well we strongly recommend you check for debris accumulation under the agitator shield each time you clean the filters Removing debris under the shield will help maintain your cleaner s excellent pick up and suction Remove debris as follows 1 Disconnect cleaner from electrical outlet 2 Check for dirt accumulation by remov ing bottom plate Fig 3 18 removing agitator Fig 3 19 and lifting agitator shield Fig 3 22 3 Remove any debris and replace shield agitator and bottom plate Figs 3 22 to 3 24 10 Headlight replacement What to buy This cleaner uses a 12 volt wedge base type 912 bulb HOOVER part No 27313101 N NC Remove lens Disconnect clean er from electrical outlet Using a screwdriver remove the two screws as shown and lift off lens Install bulb Pull old bulb straight out of socket Push new bulb straight into socket until locked in place Excessive force is not require
11. HOOVER Bagless Upright Thank you for your purchase This oe eit ct was designed for easy a sembly se e page 3 www hoo Review this manual before operating cleaner Thank you for choosing a HOOVER product Please enter the COMPLETE model and serial numbers in the spaces provided The numbers are located on the bottom of your cleaner Model Serial number Hint Attach your sales receipt to this owner s manual Verification of date of purchase may be required for warranty service of your HOOVER product Be sure to fill out and return the product registration card included with your cleaner see back cover Contents Assembling Cleaner sseseneee 3 4 HOW tO USEC ccecceseeeesseeeenseeeeneneeeneseeeenes 5 Cleaner Description scsseeee 5 Cleaning TOols csecescseeeeseeeee 7 8 If You Have a Problem ssscsseeen 13 Clearing Blockages cseceeeee 13 Important Safeguards csceeeeeees 2 Maintenance Authorized Service c sccseceeesee 12 Cleaning Filters escssseeeeee 9 10 Emptying Dirt Cup esceseeeeeeeee 8 Lubrication cceseeeseeeeeneeeeeneeeeeenes 12 Replacing Agitator Brush Roll 12 Replacing Belt cccsseeesseesscees 11 Replacing Headlight 08 10 11 Thermal Protector cscseseesseenes 12 Warranty csiscescerscssecersncsssetsarsedeacasnaesanae 14 2002 The Hoover Company www hoover com
12. bject into openings Do not use with any opening blocked keep free of dust lint hair or anything that may reduce air flow Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces Always disconnect cord from electrical outlet before servicing the cleaner Unplug cleaner when not in use Turn off all controls before unplugging Do not unplug by pulling on cord To unplug grasp the plug not the cord Never handle plug or appliance with wet hands The use of an extension cord is not recommended Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot Use vacuum cleaner only for its intended use as described in the instructions Use only attachments recommended by The Hoover Company others may cause hazards Save these instructions If you need any assistance Visit our website at www hoover com Click on the Service button to find the service outlet nearest you OR Call 1 800 944 9200 for an automated referral of service outlet locations U S only OR Call 1 330 499 9499 to speak with a representative in our Consumer Response Center Please do not return this product to the store 1 Cleaner As
13. d Belt replacement The belt on your Hoover cleaner causes the agitator to rotate and is important for the effective operation of the cleaner The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition When to replace Replace lens Reposition lens and Disconnect cleaner from electrical How to replace secure with the two screws outlet Disconnect cleaner from electrical To check belt remove bottom plate as outlet shown in How to replace Replace belt Remove bottom plate if it is stretched cut or broken Place handle in low position and turn What to buy cleaner over so bottom side is up Remove the 4 screws as shown with a To assure effective operation use only Phillips screwdriver genuine HOOVER belts with your cleaner When purchasing a new belt Lift off bottom plate 1 ask for HOOVER part No 38528033 belt package part number 40201160 Remove agitator brush roll Install new belt Replace agitator brush roll Remove agitator and used belt With lettering on outside of belt and Insert agitator through belt and place Discard used belt positioned as shown in box on J slide belt in belt guide L on agitator new belt over motor pulley K Should the agitator shield M become dislodged while replacing the belt or the agitator reposition it as shown noting the placement of
14. debris will be seen collecting in the left side of the dirt cup The main filter will collect fine particles that have passed through the pre filter assembly screen When to empty It is recommended that the dirt cup be emptied before the dirt reaches the dirt opening on back of dirt cup Fig 3 1 or after every use if preferred CAUTION Very fine materials such as face powder or cornstarch may seal the filter and cause loss of suc tion When using the cleaner for this type of dust empty the cup and clean the filters often How to empty Disconnect cleaner from electrical outlet Do not use the cleaner without dirt cup or filters in place Remove cup Squeeze dirt cup latch Pull cup forward Empty cup Remove lid Note It is not necessary to remove the main filter or the pre filter assembly to empty the dirt cup Tap side of cup until no more dust parti cles fall from the main filter Replace cup Replace dirt cup lid Place bottom of cup into cleaner Pivot cup and snap into place Filter assembly How to clean filter assembly Pull up on pre filter assembly Slide it out Remove main filter from pre tilter of cup assembly The screen C can be cleaned with a soft brush or rinsed with water Do not rinse or wash the main filter Remove dirt cup and dirt cup lid as described in How to empty dirt cup Pivot pre filter assembly toward center of cup
15. ge groomers ask for HOOVER part No 39511004 How to replace Disconnect cleaner from electrical outlet Remove bottom plate as described in The belt section Fig 3 18 Installing groomers Lift off both old edge groomers and slide new edge groomers into position as shown Reposition bottom plate and secure with 4 Phillips head screws 12 Lubrication The motor is equipped with bearings that contain sufficient lubrication for the life of the motor The addition of lubricant could cause damage Therefore do not add lubricant to motor bearings The agitator brush roll is equipped with two ball bearings that should be lubri cated periodically by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer Depot Thermal protector An internal thermal protector has been designed into your cleaner to protect it from overheating When the thermal protector activates the cleaner will stop running If this happens proceed as follows 1 Turn the cleaner OFF and discon nect it from the electrical outlet 2 Check secondary and final filters for dirt accumulation 3 Refer to Clearing blockages section 4 When cleaner is unplugged and the motor cools for 30 minutes the thermal protector automatically resets and cleaning may continue If the thermal protector continues to activate after following the above steps your cleaner may need servicing see Service
16. nside one of the extension wands Place it inside a wand for storage on the cleaner as well Cleaner description Polarized plug To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way Handle Cord hooks wrap cord around hooks for storage The top hook rotates right or left for easy cord Carrying handle Stair cleaning handle located on lower edge of dirt cup 13 14 15 16 22 23 Dusting brush Crevice tool Furniture nozzle Long crevice wand stores inside wand release 17 Hose hook Hose 18 Dirt cup latch ON OFF switch located 19 Dirt cup lid on left rear corner of 20 Dirt cup cleaner body 21 Dirt cup handle Main filter inside cup Pre filter assembly inside cup 8 Headlight 7 Handle release lever step on lever to lower handle to operating or low positions 9 Nozzle control knob slide 10 knob to correct setting for height of carpet being cleaned Furniture guard helps prevent cleaner from Operate cleaner only at 11 Wands ON OFF switch Plug cord into electrical outlet To turn cleaner ON push switch A toward front of cleaner
17. oards It can also be used for extra reach with the dusting brush and or extension wand G Extension wands are used to give extra length to your hose Use it with any of the above tools 7 Attach wand and tools Attach tool or wand to the hose H by pushing it firmly into hose Attach second wand or tool to the wand in the same manner Twist wand or tool slightly to tighten or loosen the connection Extra reach hose available at additional cost The extra reach hose provides you with a 20 foot reach to allow easier cleaning of stairs and hard to reach places Follow the steps below for attaching and detaching hose Push ON OFF switch to OFF position Remove regular hose from cleaner Align end of extra reach hose with projec tions I over slots J in dirt duct Slide hose into slots K and twist hose to lock it into place To detach hose reverse procedure Attach wands or tools to the other end of hose 3 Maintenance Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure contin ued cleaning effectiveness Dirt cup The dirt cup assembly consists of the following parts Lid A Dirt Cup B Pre filter Assembly C Main Filter D behind pre filter Dirt Opening E While the cleaner is in operation the pre filter assembly screen will stop arger debris from entering the main filter chamber This larger
18. on CAUTION Agitator continues to rotate while cleaner handle is in upright position Avoid tipping clean er or setting it on furniture fringed area rugs or carpeted stairs during tool use How to clean tools To clean the hose wipe off dirt with a cloth dampened in a mild detergent Rinse with a damp cloth Cleaning tools may be washed in warm water with a detergent Rinse and air dry before using Remove hose When using cleaning tools cleaner handle should be in the upright posi tion Also turn cleaner OFF before disconnecting and connecting hose to hose tube A To use hose lift hose end as shown Lower cover B onto hose tube When you are finished cleaning with the tools be sure to lift cover from hose tube and reposition hose end into tube Select proper tool C Dusting brush may be used for carved furniture table tops books lamps lighting fixtures venetian blinds baseboards shutters and registers D Furniture nozzle may be used for upholstered furniture draperies mat tresses clothing automobile interiors and carpeted stairs E Crevice tool may be used in tight spaces corners and along edges in such places as dresser drawers uphol stered furniture stairs and baseboards F Crevice wand stores inside exten sion wand can be used in tight spaces corners and along edges in such places as dresser drawers upholstered furni ture stairs and baseb
19. oover Authorized Warranty Service Dealers Depots For an automated referral of authorized service outlets in the U S A phone 1 800 944 9200 OR visit The Hoover Company on line at www hoover com This warranty does not cover pick up delivery or house calls however if you mail your appliance to a Hoover Factory Service Center for warranty service transportation will be paid one way While this warranty gives you specific legal rights you may also have other rights which vary from state to state or province If further assistance is needed or if there are questions concerning this warranty or the availability of warranty service outlets write or phone the Consumer Response Center The Hoover Company 101 East Maple St North Canton Ohio 44720 Phone 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376
20. sembly Carton contents Empty carton Find the parts shown before disposing of packing materials A Handle section B Cleaner body C Hose cleaning tools and wands D Handle bolts and nuts packet in bag with owner s manual leaner body Push bolts into holes on back of handle O O Remove tape and remove dirt cup from Slide handle ont cleaner body Switch A should be in OFF position Continued gt 3 PaaS aa Z TES Se Place nuts in recessed areas on front of handle Hold each nut in place while tightening each bolt securely with a Phillips screw driver Place bottom of cup into cleaner Pivot cup and snap in place Position cord on back of cleaner as shown and press cord into clip Attach hose Align end of hose with projections A over slots B in dirt duct Note Hose must be connected as shown for all operations Slide hose into duct B and hose to lock it into place twist Lift hose tube cover C Position hose over hose hook D and into hose tube E Position tools Place smaller unridged end of wand into bottom of rack Snap wand into clip Repeat with other wand Snap ends of dusting brush A crevice tool B and furniture nozzle C into clips as shown The crevice wand is packed i
Download Pdf Manuals
Related Search