Home

Hoover S3239 User's Manual

image

Contents

1. 000 c cee eee eee 12 1975 1978 1980 1992 The Hoover Company Important Safeguards e Read all instructions e Warning Electric shock could occur if used outdoors or on wet sur faces e Close supervision is necessary when any appliance is used by or near children Do not allow vacuum cleaner to be used as a toy or to run unattended at any time e Keep hands feet loose clothing and hair away from rotating agita tor Do not operate the cleaner in bare feet or when wearing open toe shoes or sandals e Don t run power nozzle over cord It may damage insulation e Do not use cleaner to pick up matches or live ashes and cigarette butts e Avoid picking up hard sharp objects with the cleaner They may damage the cleaner and the bag e Unplug cleaner when not in use Turn machine off at switch before unplugging e Always disconnect cord from electrical outlet before servicing the cleaner e Change bag frequently when picking up very fine materials such as powder e Grasp the plug to disconnect from wall outlet to avoid damage to cord plug prongs or receptacle e If cleaner has a cord reel hold onto the plug while cord is being re wound to prevent cord from whipping e The use of an extension cord is not recommended e If cleaner is in disrepair do not attempt to operate e Have repairs made by the qualified personnel at Hoover Factory Service Centers or Authorized Hoover Warranty Service Dealers e
2. Upright and Operating To lower handle to the Operating position place your foot on the grooved area located above the Agitator Control Pedal on the nozzle and push the handle down 7 Swiveling handle and wands The handle and wands conveniently swivel to the right for ease in clean ing under low furniture To swivel handle and wands twist handle to the right The handle and wands should click out of the original position To swivel handle and wands back to the original position twist handle to the left Carpet and rug cleaning When using the electronic power nozzle for carpet and rug clean FLOOR ing a green LED light on the con CARPET trol panel should indicate the CARPET position This setting provides the suction and agitator action necessary to deep clean carpets Step on the Agitator S N Control Pedal to change the set ting Hard surface floor cleaning The electronic power nozzle can be used for cleaning hard surface floors such as wood linoleum vinyl asphalt and rubber tile sealed cork concrete and terraz zo as well as carpet FLOOR CARPET To adjust the electronic power nozzle for hard surface floor cleaning step on the Agitator Control Pedal A green light will indicate the FLOOR position This setting provides suction but no agitator action The Wall Floor Brush may also be used for cleaning bare floors Agitator speed selection N
3. Use vacuum cleaner only for its intended use as described in the in structions The use of attachments not recommended by the appli ance manufacturer may cause hazards Save these instructions Quali Products thru O Employee Participation Unpacking Unpack the cleaner from the carton and identify the parts shown Remove and dispose of the cardboard packing A Canister cleaner nse C ITQ B Electronic power nozzle D je j C Throw away bag DER D Tools with tool storage rack extension wands Model 83237 has two sets of wands and hose Jeg The cleaner assembled will look like the drawing below 3 2 1 Furniture Guard is located around cleaner and electronic power noz zle Combination Carpet and Floor Electronic Power Nozzle contains agitator brush mechanism and automatically adjusts to different carpet heights The nozzle has both a NORMAL and a DEEP CLEAN agitator speed and a panel of four LED indicator lights 3 Headlight 4 Hose Cord Connection to Cleaner is made by plugging hose cord 10 11 12 13 14 15 16 17 18 19 20 into cleaner base at receptacle Large Wheels provide easier towing pull cleaner using hose to guide the cleaner easily over carpet area rugs and door sills Check Bag Indicator lights up when throw away bag should be checked to determine if changing is required Cord Rewind Control is
4. power nozzle The belt located under the nozzle cover should be replaced if the CHECK BELT light remains ON To service remove the nozzle cover see following section How to replace the belt Disconnect cleaner from electri cal outlet and disconnect elec tronic power nozzle from exten sion wands Turn nozzle over and unscrew the 2 Phillips head screws from the nozzle base 15 a ZT a MOTOR PULLEY AGITATOR PULLEY al i a Saag en A oe A H Zz YN Return nozzle to original position and lift up back of nozzle cover Then remove cover rotating it forward and lifting it off To remove the agitator position your hand underneath the nozzle base at the agitator opening and push up the belt end of the agita tor Remove agitator and old belt Place one end of new belt around the plastic agitator pulley with lettering on outside of belt Then slip other end of belt around motor pulley Position round projection on end of agitator opposite the belt into the opening in the wall of the nozzle base Slide belt end of agitator into place by pulling agitator forward and lining up metal projection on end of agitator with slot in wall of nozzle base Then push agitator down into position Roll agitator to make sure belt is positioned properly The cover attaches at the front of the nozzle Place the notched edge at the front of the co
5. when moving furniture 4 Keep your cleaner operating at peak performance level have in spection and service performed by a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer 22 V C M A VACUUM CLEANER MANUFACTURERS ASSOCIATION HOOVER AN ASSOCIATION MEMBER Service To The Consumer Since 19 13 Consumer information This information has been compiled by the Vacuum Cleaner Manufacturers Associa ation from Government and Private Sources concerned with product safety These basic guidelines are for your protection and convenience TO AVOID ELECTRIC SHOCK Never vacuum damp or wet surfaces or liquids Do not store machine outdoors Replace worn or frayed power cord immediately TO AVOID ACCIDENTS Never vacuum live ashes or cigarette butts Never run machine over or place sharp objects on the power cord Never let children use machine as a toy Use extra caution when cleaning on stairs Keep machine on floor not on chairs tables etc When machine is turned on never allow frngers eyes hair garments etc to come near intake suction ports or revolving brushes Never leave machine running or cord plugged in when unattended Turn machine off at switch before unplugging from wall outlet When unplugging machine grasp plug not cord guide cord and plug during wrapping or cord reel rewinding The use of an extension cord is not recommended Never vacuum in the presence of flammable or combu
6. HOOVER Celebrity QUIET Q SERIES pn Cleaner with Electronic Power Nozzle Fill in and retain The HOOVER vacuum cleaner you have just purchased is a combina tion cleaner It has an electronic power nozzle for carpet and floor cleaning and has cleaning tools for above the floor cleaning Your cleaner is a model no and has a serial number For your personal records please enter the model number and serial number in the spaces provided above and retain in a safe place The model number and serial number appear on the bottom of the cleaner Save Index Assembling Cleaner 022eeeeeeeeeees 5 7 Cleaner Description 2eeeeee eee eeeaee 3 5 Energy Saving Tips e cece cece eee eens 22 How To Use Check Bag Indicator 2 eeee eee eeee 7 Cleaning Tools s eeeeee cece eeeees 10 1 Electronic Power Nozzle 2ee0e0e 7 10 Two Speed Switch eeeseeee ee eeeees 7 If You Have a Problem 2020ee0eeuuee 21 Important Safeguards esee eee eee eee 2 LUBDNCAUON wongane baronies e ha yawkie ay Maintenance Cleaning Secondary Filter 2 055 15 Clearing Obstructions eee eee eee 14 Replacing Agitator Brushes and Brush Roll sseseeeeeeeeueeeuee 17 19 Replacing Bag see eee cece ee eens 13 14 Replacing Belt eeeeeeee eee e eens 15 17 Replacing Headlight se00 19 20 Storing Cleaner
7. ORMAL FLOOR GJ The electronic power nozzle offers Ca carrer two agitator speed settings The CHECK NORMAL speed is used for J Power most carpet cleaning and the GUARD DEEP CLEAN setting is availa ble for increased agitator action CHECK BELT light The electronic power nozzle auto matically monitors its belt condi tion When the belt needs replac ed the red CHECK BELT light will come ON and remain ON until the belt is replaced To replace belt refer to The belt section under Maintenance POWER GUARD feature The electronic power nozzle has a unique feature which warns of motor overload conditions The red POWER GUARD light will come ON and the nozzle will shut OFF if the motor is stalled or if an agitator obstruction causes a motor overload Before remov ing any agitator obstructions or opening the Suction Regulator see Automatic nozzle adjust ment the CAUTION statement below must be followed CAUTION If the POWER GUARD light is ON the agi tator may suddenly start while you are removing obstructions from the agitator area Therefore turn cleaner OFF and unplug before cleaning or servicing The elec tronic circuitry will be automati cally reset when the cleaner is turned OFF Brushed edge cleaning Brushed edge cleaning is provided on both sides of the nozzle to re move imbedded dirt in carpet
8. b is part of the electronic circuit and the elec tronic power nozzle motor will not operate if the bulb is burned out The bulb must be replaced with a 15 watt bulb Use Hoover part number 16113 or Sylvania 15T7DC bulb How to replace the headlight Disconnect cleaner from electrical outlet and disconnect electronic power nozzle from extension wands 19 Turn nozzle over and unscrew the 2 Phillips head screws from the nozzle base The cover attaches at the front of the nozzle Place the notched edge at the front of the cover into the groove in the nozzle base Return nozzle to original position and lift up back of nozzle cover Then remove cover rotating it forward and lifting it off Push bulb into socket and twist to remove Push new bulb into socket and twist into place Maintaining front connection ro tate cover over nozzle base and pull nozzle cord through opening in cover Turn nozzle over and replace screws 20 If you have a problem This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory If a minor problem develops it usually can be remedied quite easily when the cause is identified Accordingly this check list is provided for your convenience Problem Possible cause Possible solution A Cleaner 1 Not firmly plugged in 1 Plug unit in firmly won t run 2 No voltagein wall plug 2 Check fuse or breaker 3 Blown fuse trippe
9. d near the slots on the agitator Match the bar side of the bar brush assembly with the label on the agitator shell Slide the new assemblies into the slots while twisting the assemblies in a coun terclockwise motion Push in as far as possible tapping the other end lightly if necessary Be sure brushes and bars are aligned for full length of agitator 18 4 Line up locator on end sections with slot on agitator Push end sections into position Note The pulley end section has a U shaped locator that fits into the U shaped slot on the appro priate agitator end 5 Slide new brush roll onto pulley end section fitting in dented areas on brush roll over projections on end section Ar row in brush roll must point to ward agitator LOCATOR 6 Screw on end plates and tighten 7 Should you accidentally dis place any part of the agitator dur ing assembly reassemble as shown SHAFT goes through center of agitator METAL BEARING COVER END WASHER SECTION ROO PLASTIC DUST WASHER BRUSH ROLL END PLATE SHIELD o am 3 p 1o a SPACER i PLASTIC Locator DUST SLOT SHIELD FLAT METAL ENDPULLEY SENT LOCATOR SIDED BEARING SECTION ROUND oy PROJECTION COVER aes Replace belt agitator and nozzle cover The headlight The headlight located on top of the electronic power nozzle operates when the cleaner is turned on Note The headlight bul
10. d breaker 3 Replace fuse reset breaker B Cleaner 1 Bag full 1 Change throw away bag suction 2 Obstruction in hose wands 2 Remove foreign object low or nozzle connector 3 Secondary filter dirty 3 Clean filter 4 Bag not opening 4 Open bag by pulling folds 5 Suction regulator control 5 Close suction regulator open 6 Hose not properly connected 6 Insure hose properly to cleaner connected 7 Switch on LO speed 7 Turn switch to HI C Agitator 1 Hose power cord and or 1 Plug firmly into receptacle won t run power nozzle cord not firmly on cleaner base and under plugged in neath hose handle 2 Broken belt CHECK BELT 2 Replace belt and replace agi light ON tator brushes if severly worn 3 Motor overload POWER 3 Remove obstruction from agi GUARD light ON tator or motor pulley 4 Headlight bulb burned out 4 Replace bulb D Nozzle 1 Low cleaner suction 1 See Item B won t pick 2 Obstruction in nozzle 2 Remove foreign object up connector 3 Agitator not running 3 See Item C 4 Agitator brushes and 4 Replace brushes and brush roll worn brush roll If the problem persists check the Yellow Pages of your telephone book under Vacuum Cleaners Household for your nearest Hoover Factory Service Center or Authorized Warranty Service Dealer where approved HOOVER service and genuine HOOVER replacement parts may be ob tained The warranty provided with this p
11. foot operated To unwind cord pull to desired length Step on Cord Rewind Control to automatically re wind for storage Hold plug until cord is rewound Tool Storage Rack provides tool storage for crevice tool furniture nozzle wall floor brush and dusting brush Removable Furniture Nozzle Wall Floor Brush Dusting Brush Crevice Tool ON OFF Control is a convenient foot operated control on top of cleaner Two Speed Switch allows for HI or LO speed selction Spring Latch locks extension wands Extension Wands connect to hose and electronic power nozzle or cleaning tools Model S3237 use curved wand and straight wand with cord clips when using electronic power nozzle use extra set of wands with cleaning tools Cover Latch Carrying Handle LED Light Emitting Diode Indicator Lights show settings for FLOOR and CARPET cleaning and warnings for CHECK BELT and POWER GUARD Agitator Control Pedal is a foot operated control to set nozzle for CARPET or hard surface FLOOR 21 Suction Regulator should be opened for easy cleaning of some types of carpet lightweight flexible rugs and lightweight draperies 22 Cord Clips clip nozzle cord to extension wands 23 Nozzle Cord Connection to Handle is made by plugging nozzle cord into receptacle underneath the handle 24 Plastic Latch Ring rotates to connect handle to extension wand or to cleaning tools 25 Handle is on end of h
12. he exten sion wands rotate the plastic latch ring on the handle to accept the button projection on the curv ed wand Push the handle over the wand so that the button projection fits into the slot Turn the latch ring to lock wand in place Connect nozzle power cord to receptacle underneath handle aaia eet ow 3 Attach tool storage rack To attach tool storage rack in To remove press front middle sert rear projections of rack into section and lift rack up the two rear slots on top of the cleaner Snap front middle sec tion into place How to use Two speed switch Your cleaner is equipped with a switch for Hi and Lo speed Use Lo speed when reduced suction is desired such as when cleaning throw rugs or when using the tools on delicate fabrics Position tools in appropriate sec tions on rack as indicated by symbols Use Hi speed for all cleaning tasks when maximum suction is desired Check bag indicator With the cleaner on Hi speed the Check Bag Indicator will light up when the bag needs replaced If powdery substances have been picked up the bag may need replaced even if it is not full Note The bag may not need replaced if the light comes on during tool use or if there is an obstruction in the hose wands or power nozzle See Maintenance Section Electronic power nozzle Handle adjustment The handle has two positions when used with the electronic power nozzle
13. ian blinds baseboards shutters and regis ters IMPORTANT USER INFORMATION This Electronic Power Nozzle features a reliable elec tronic circuit to control and protect the nozzle The headlight functions as part of this electronic protection system The headlight bulb should provide years of normal use however the motor will not operate if the bulb burns out For bulb replacement use a 15 watt lamp only Use Hoover part number 16113 or Sylvania 15T7DC bulb 11 82 Litho USA 54823 026 To connect and remove tools To use the cleaner with tools dis connect the nozzle from the ex tension wands For Model 3237 leave the nozzle assembl ed to the wands and only discon nect nozzle cord and curved wand from handle since two ad ditional wands are provided for use with tools To connect the tools insert end of tool into the extension wand and snap into position To dis connect press down on the cen ter of the white plastic spring latch and remove tool Tools may also be attached to the handle grip by rotating the plastic latch ring to accept the button projection on the tool Then turn the latch ring as shown to lock the tool in place To remove the tool reverse the above procedure Power cord To avoid damage to the power cord leave it connected to the receptacle on the cleaner at all times To clean stairs Clean stairs by standing the cleaner on its side as pictured in the illustration Clean
14. near baseboards and furniture Guide either side of the nozzle parallel to the edge of the carpet or furniture as shown C FLOOR C CARPET CHECK E BELT POWER wt ome GUARD Automatic nozzle adjustment The electronic power nozzle ad justs automatically to the correct cleaning height for all carpets from low pile to shag If the power nozzle is difficult to push or if the POWER GUARD activates due to heavy carpet load open the Suction Regulator Cleaning tools Removing and replacing tools To remove tools from tool storage rack grasp the top of the tool as shown in the illustration and lift up To replace tools position tool in appropriate section on the tool storage rack and snap into place Select the proper cleaning tool The cleaning tools have many uses Select the tool best suited for the cleaning task from the descriptions below Adjust the Suction Regulator to select the amount of suction appropriate to the cleaning task 2 IN arrrT Tri oe a Cr eae NaN 1 Crevice tool for radiators dresser drawers spaces between kitchen appliances 2 Wall floor brush for walls and very irregular hard surface floors such as brick and slate 3 Furniture nozzle for uphol stered furniture draperies tapes tries mattresses clothing auto mobile interiors and carpeted stairs 4 Dusting brush for carved fur niture table tops books lamps lighting fixtures Venet
15. ose for use with extension wands or cleaning tools Operate cleaner only at voltage specified on data plate on bottom of cleaner How to assemble 1 Connect hose To connect hose insert hose into opening of cleaner lining up the arrow on the hose with the dot on the cleaner Turn the hose clock wise until the arrow lines up with the bar on the cleaner and latch locks into place When the hose is attached prop erly the hose cord plug will reach to the receptacle on the cleaner Insert the plug firmly and as deep into the receptacle as possible To disconnect hose first remove hose cord plug from receptacle Then depress latch away from hose connection opening in clean er While holding latch turn the hose counterclockwise until the arrow lines up with dot on the cleaner Remove hose NOZZLE CONNECTOR 2 Attach electronic power nozzle Note For most convenient use with electronic power nozzle connect curved and straight wand with cord clips to nozzle Attach the electronic power noz zle at the end of the straight wand by fitting the button projection on the nozzle connector into the opening at the end of the wand Be sure the nozzle is locked in place To release press down on the center of the spring latch Attach the curved wand to the straight wand Position cord into cord clips on extension wands placing excess cord between nozzle and bottom cord clip To attach the hose to t
16. re to give the model number of your cleaner What bags to buy Use HOOVER bag type H with this cleaner To assure that your HOOVER cleaner operates at peak performance it is imperative that you use only genuine HOOVER throw away bags made by The Hoover Company HOOVER bags can be y identified by the trademarks Replacing the throw away bag Disconnect cleaner from electri cal outlet Open the cleaner by lifting up on the latch to release the cover Push used bag away from holder and lift out Grasp edges of collar section and push opening of collar section of new bag onto holder Make sure collar is pushed completely up to the ridge on the holder 13 Adjust bag around the motor housing and open the folds of the bag to allow the bag to properly fill Make sure all four folds are open Note A bag that does not ex pand properly may restrict air flow In this event check the bag making sure all the folds are open High suction on some carpet surfaces can cause the nozzle to hug the carpet and also restrict air flow When this oc curs reducing the suction with the Suction Regulator or swit ching to LO speed may be helpful Clearing obstructions Removing larger items from car pet and floor surfaces before vac uuming will help prevent obstruc tions in the hose wands or nozzle connector and maintain the cleaning effectiveness of your cleaner To check for obstructions firs
17. roduct has a listing of the Hoover Factory Service Centers If you are unable to obtain the informa tion you need from the Yellow Pages contact a Hoover Factory Service Center to find your nearest Authorized Warranty Service Dealer For service under warranty follow the instructions in the Warranty provided with this product Do not send your cleaner to The Hoover Company in North Canton for service as this will result in delay Always identify your cleaner by model number when requesting informa tion or ordering replacement parts The model number appears on the bottom of the cleaner If further assistance is needed contact The Hoover Company Con sumer Affairs Department North Canton Ohio 44720 216 499 9200 21 Lubrication The motor is equipped with one ball bearing and one roller bearing These bearings contain sufficient lubrication for the life of the motor The addition of lubricant could cause damage Therefore do not add lubricant to either motor bearing The agitator is equipped with two ball bearings that should be lubricated periodically This should be done by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer T saving tips Replace throw away cleaner bag promptly before overfilled Use a genuine HOOVER bag made for your model cleaner 2 To maintain effective cleaning replace agitator brushes brush roll and belt when necessary 3 Turn off cleaner when not in use such as
18. stairs from bottom to top 4 To clean hard to reach areas The tools attached to the curved wand as shown will enable you to clean many hard to reach areas especially crown moldings tops of drapery rods shelves and pic ture frames Storing cleaner Your cleaner can be stored on end as shown in the illustration Store the electronic power nozzle with the handle in the upright position The hose extension wands elec tronic power nozzle and tool stor age rack can be stored separately from the cleaner if desired Maintenance The following sections are concerned with proper maintenance of the cleaner Familiarize yourself with these home maintenance tasks and keep this owner s manual in a convenient place where you can refer to it when needed Proper use and care of your cleaner will assure continued cleaning effectiveness The bag When to replace When the Check Bag Indicator light is on the bag should be checked for fullness and replaced if necessary CAUTION Very fine materials such as face powder cornstarch fire place ashes or fireplace soot may seal the throw away bag and may cause it to burst even though it is only partially full of dirt When the cleaner is used to remove material of this nature the bag should be changed frequently 12 Where to buy bags Bags may be purchased from your local Authorized Hoover Dealer or from a Hoover Factory Service Center When ordering bags be su
19. stible liquids or fumes Always unplug power cord from wall outlet before servicing machine or attaching accessories Store machine promptly after each use to prevent accidents from tripping over power cord or machine Use machine and accessones only n manner Intended by manufacturers FOR BEST PERFORMANCE Keep your machine and all accessories clean and in good operating condition Change or clean bags and or filters as recommended by manufacturer to maintain optimum cleaning efficiency after unplugging the power cord Periodically check revolving brush for build up of lint hair or other foreign material and remove as necessary after unplugging the power cord Adjust or replace cleaning brushes when worn after unplugging the power cord Have machine checked periodically by manufacturer s authorized service center Use only manufacturer s authorized service center for parts or service Store machine carefully in a dry area For optimum cleaning performance and safety study and follow your Owner s Manual keep it in a handy and safe place for future reference THE HOOVER COMPANY NORTH CANTON OHIO 44720 R3 9 83 3237 39 Litho USA 56513 194
20. t disconnect power nozzle cord and wands from cleaner base Turn cleaner ON and check hose end for suction Remove any obstructions Remove power nozzle from wands and attach wands to hose Check for suction and remove any obstructions Before attaching power nozzle to wands check nozzle connector While holding nozzle push noz zle connector down to lowest po sition Look into nozzle connector and remove any obstructions 14 Secondary filter To clean secondary filter Disconnect cleaner from electri cal outlet The secondary filter protects the motor from dirt particles If the filter becomes dirty either clean or replace it To remove secondary filter open cover of cleaner and lift filter off of motor housing Clean filter by rinsing it in water When dry position filter around motor hous ing with notched edge at the bot tom and to the back of the motor housing The belt The belt in your electronic power nozzle drives the agitator It has been designed specifically for use in this cleaner and is important for effective operation There are other belts manufactured that are similar in shape and size but are not designed for the HOOVER electronic power nozzle Such belts do not operate the agitator correctly and may create stress which could damage your electronic power nozzle Use only a genuine HOOVER Belt No 38528 011 when a belt replacement is necessary When to replace the belt on electronic
21. ver into the groove in the nozzle base While maintaining front connec tion rotate cover over nozzle base and pull nozzle cord through opening in cover Turn nozzle over and replace screws Agitator brushes and brush roll When to replace brushes Disconnect cleaner from electri cal outlet before checking brushes To check condition of brushes place edge of a card on the bot tom of nozzle base across agita tor opening Rotate agitator by hand If brushes do not touch edge of card all four brushes and brush roll should be replaced to maintain cleaning effectiveness When replacing agitator brushes and brush roll ask for HOOVER part No 48445017 and part No 48418 001 END SECTION BAR BRUSH ASSEMBLY How to replace agitator brushes and brush roll Disconnect cleaner from electri cal outlet and disconnect elec tronic power nozzle from exten sion wands Remove nozzle cover agitator and belt following directions in How to replace belt section 1 Hold agitator as shown Turn end plates in opposite directions until one end plate comes off 2 Pull or pry out end sections as shown in illustration Note Remove brush roll and then pulley end section by pulling straight out 3 Note position of bar brush as semblies to assure correct re placement Remove bar brush assemblies by pulling them from agitator slots Use pliers if necessary The word BAR is stampe

Download Pdf Manuals

image

Related Search

Related Contents

Installation EPLAN platform 2.4  Gateway Five iPod, USB, Bluetooth User Manual Opel  ユーザーズガイド - バーコードリーダー  MANUAL DE INSTRUÇÕES Isolador Analógico: KD - 7172HT  JOURNAL DU COLLEGE  Assembly Manual for RevC Board  航空事故調査報告書 個 人 所 有 ウィードホッパー式 JC3ーC型超軽量重  Samsung ES9 Vartotojo vadovas  iso-tech idm 17 crayon-multimetre manuel d`instructions  UMC800 User Utility Benutzerhandbuch  

Copyright © All rights reserved.
Failed to retrieve file