Honeywell WT6500 User's Manual
Contents
1. 2 10 THWN 2 6 GND CONDUIT SEE TURBINE TO CONTROLLER SIZE MAX DISTANCE 3 FEET CHART ON SHEET 1 Figure 2 10 Power Wiring Diagram Turbine Wiring and Distances The HONEYWELL Wind Turbine and SMARTBOX Controller can be installed at a maximum distance of 200 feet apart The SMARTBOX Controller and battery enclosure can be installed at a maximum distance of 10 feet apart Turbine Current Rating and Wiring The turbine input is rated for 20 amps maximum Isc short circuit The recommended wire type is 10 AWG USE 2 RHW 2 or THWN 2 90 degrees C wire for a turbine to Smart Box distance of up to 150 feet The wire gauge should be increased to 8 AWG for a distance of 150 200 feet Due to the outside location of the turbine a 70 degree C ambient temperature correction is recommended HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Turbine Installation 20 o D BATTERY TURBINE L ES F IRE SIZE 24VDC BATTERY 77 BATTERY REFER INSTRUCTION MANUAL P RECAUTION Un 100 MAXIMUM D AMP RE LE FUSIBLE EXTERNE ET EXTERNE DEBRANCHE LE CHANGEMEN2. 20 Control WANING esL 21 nasaq YW 22 1217217 9 ANYA 23 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Table of Contents VI kw w 3 Specifications Technical Specifications 25 4 Warranty Information 27 5 Appendix Pole Mount Drawing 32 ROOFBOX Mount Drawing 33 ROOFBOX with QUADPOD Mount Drawing 34 Ballast Mount Drawing 35 One Line NP 36 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 1 Introduction Introduction Chapter 1 describes the HONEYWELL Wind Turbine For Information On See Product Description Shipping Contents Before Installation Lift Point Q N N N HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Introduction 2 IIC i si Product Description The HONEYWELL Wind Turbine is a novel electric generator Worldwide patents pending It consists as shown in the product detailed schematic of a central wheel made of aluminum rim stainless steel spokes and aluminum hub
3. Mew C 1907 90 01 QN93 90 2 ip SFI FUSE DYO 01 Nug LHM NYS AJ LHM NYD JOSLNOS ONIM SM adj c N LAA A e e e e yn y m 14 R 20 zi el ej HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Turbine Installation 22 EE ae Grounding PROFESSIONAL INSTALLATION A certified and trained electrician must install and commission this turbine using the National Electric Code NEC or if in Canada the Canadian Electric Code CEC and in compliance to the local permitting and zoning codes The SMARTBOX Controller is designed to work only with the HONEYWELL Wind Turbine The turbine uses a negative grounded electrical system Grounding for the turbine battery and AC circuits are provided inside the wiring compartment Each ground connection can accommodate up to 6 AWG wire size GFI A fuse rated at 250V accessible from the bottom of th
4. Controller Manual for full details Only a certified and trained electrician should install and maintain the Junction Box the attached Dump Load resistor housing and anemometer 1 in TIER Figure 2 7 Junction Box Enclosure HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 17 Turbine Installation r Junction Box Block Diagram WIND WIND SPEED WIND DIRECTION JUNCTION BOX DIVERSION LOAD CONTROL LOGIC WIND CONTROL TURBINE HV POWER OUTPUT TO SMARTBOX CONTROLLER Figure 2 8 Junction Box Block Diagram HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 18 Turbine Installation Turbine Wiring Overview 3SVHd 315NIS HOLIMS NIVW LndNi N H AINGNOD 9 2 dWVSL AOZL 3SVHd 5 HOLIWS 805 OL ANdLNO v AINGNOD ND 98 CNMHLCU O 4 9 seDed eulj euo xipueddy ees VNOLLdO NY 1333 1510 AInGNOD ND Z NMHLOLE Z ad 13
5. See page 32 in the Appendix for design and specifications e PROFESSIONAL INSTALLATION required The QUADPOD wind turbine mounting system is a novel design in that it can be used on a flat roof area or any roof angle due to its strong hinged design The QUADPOD when mounted according to its installation procedure always ensures that the wind turbine is in a vertical stand at various roof angles The QUADPOD installation on a roof should be approved by a local Professional Engineer PE All of the options listed have been rated by our Professional Engineer Please refer to the following designs and their included specifications See page 33 in the Appendix for design and specifications e PROFESSIONAL INSTALLATION required The HONEYWELL Wind Turbine may be mounted on the QUADPOD which be securely mounted onto a ROOFBOX The ROOFBOX design is shown below and certified by our Professional Engineer The ROOFBOX installation on a roof when selected should be approved by a local Professional Engineer PE All of the options listed have been rated by our Professional Engineer Please refer to the HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Turbine Installation 12 following designs and their included specifications See page 34 in the Appendix for design and specifications Ballast Mount See page 35 in the Appendix for design and specifications Turbine Wiring ELECTRIC SHOCK HA
6. Mount residential small commercial flat or pitched Ballast QUADPOD base weighed down commercial flat roof Poles Material Height concrete 20 ft steel 30 ft wood 40 ft HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Turbine Installation Pole Mount QUADPOD Mount ROOFBOX Mount Figure 2 3 Mounting Options Failure to follow proper installation practices for any of the mounting options could result in death personal injury and or property damage yN The vertical axis of the turbine must be level when installed WARNING Turbines installed with their vertical axis off level will see significant impact on performance IMPORTANT The ROOFBOX QUADPOD system is designed for pitched or flat roof tops As roof construction and roof lines vary pole mounted installations are recommended for residential environments for optimal cost flexibility and performance PROFESSIONAL INSTALLATION required The pole mount for the HONEYWELL Wind Turbine can be fabricated out of concrete steel or wood A detailed design is shown below of a direct burial pole that is certified for WindTronics Whichever pole design option is chosen it should be approved by a local Professional Engineer PE All of the options listed have been rated by our Professional Engineer Please refer to the following designs and their included specifications
7. Two ceramic bearings are used to attach this wheel to the center shaft of the turbine Custom shaped glass filled nylon blades are attached to the spokes of this wheel Permanent magnets are affixed to the tips of these blades at the rim of the wheel The wind flows through this wheel with ease and it interacts with the aerodynamically designed blades to induce a rotational motion in the wheel around its center hub This rotational motion is THE indication that wind energy is being extracted from the flowing wind stream The magnets travel at a much higher speed for any given wheel rotation because they are located at the rim of the wheel This placement of the permanent magnets at the blade tips produces the needed high speed motion without the need of any gearing mechanism The elimination of gears in this wind turbine technology enhances wind energy extraction efficiency and prolongs its operating life The permanent magnets at the blade tips and wheel rim travel at high speed within a novel and custom built stator system This stator system converts the motion of these magnets into electricity A glass filled nylon aerodynamically shaped shroud covers the stator system An anemometer is attached to the HONEYWELL Wind Turbine that produces near instantaneous readings of wind speed and direction at the point of installation The electric output of the stator system is a variable direct current DC and is connected together with the anemome
8. may also minimize damage due to lightning strikes Grounding information is available from the National Electric Code NEC USA 2005 as well as the International Electrotechnical Commission IEC standard 60364 5 54 section Erection of Electrical Eguipment Earthing Arrangements Protective Conductors and Protective Bonding Conductors Please reference the NEC and IEC standards regarding full details of grounding this wind turbine Please also refer to 205 article 250 53 G regarding the grounding electrode installation Also refer to 2005 NEC article 250 66 A regarding conductor size where it stipulates that where a grounding electrode conductor is connected to a rod pipe or plate electrode that portion of the conductor that is the sole connection to the grounding electrode shall be a minimum of 6AWG copper wire or 4AWG aluminum wire HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 23 Turbine Installation Operation Personal Injury and Property Damage Hazard WARNING Do not touch revolving turbine blades or insert objects including sticks and screwdrivers into revolving turbine blades Failure to follow this may result in death personal injury or property damage PROFESSIONAL INSTALLATION A certified and trained electrician must e install and commission this turbine using the National Electric Code NEC or if in Canada the Canadian Electric Code CEC and in compliance to the local permitting an
9. service TIP The instructions in this section apply to a typical installation Installation procedures may vary according to your specific application For special ap plications consult a gualified electrician or your WindTronics certified dealer IMPORTANT Installation must be compliant with all local electrical codes Installation of this eguipment should only be performed by a gualified electrician by a Certified Renewable Energy System Installer le t b o BACK UP DOWN ENTER Honeywell Em ED ni gll Figure 2 5 The SMARTBOX Controller HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 15 Turbine Installation The Battery Box The Battery Box is a NEMA 3R type and must be mounted on the wall near the SMARTBOX Controller The Battery Box requires its own On Off switch and a 100 amp fuse Please refer to the SMARTBOX Controller Manual for connecting the Battery Box to the SMARTBOX Controller and also for maintenance and service D IMPORTANT Please read the SMARTBOX Controller Manual TIP Always c
10. 1 ILICE E TELE aee Eis EA E HF WEN Tl KT m Ti M ewon Puy iere a imm pom pukami ym ON yU D Tupana ha EE EW FED ym a U HE LLED A WLR pryn apo ee DD DT _ YT UI FN LEDD DADO LIO P TH LES 1 J Te PS4 PR ae eee ee UE ED TWYN TUR SE ee eS UN ee KER T Gell L R CR ee ee ee T ee ee HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 33 ROOFBOX Mounting ATTACH WINDTRONICS GUAD POD TO ROOF BOX WITH 4 1 4 3 2 GRK s EA PAD TYPICAL ROOF SHINGLES TO MATCH KE amp WATERSHELD FULL SURFACE V2 05B SHEATHNG OR FEQ ROOF ATERIALS SHINGLES TO MATCH amp WATERSHIELD FULL COVERAGE 2 OSB 5 2x4 TREAT 3 4 x 5 h 4 RIDGE HEATHNG 2x4 RAFTERS SPF 20 ED WD FURR LVL BD 1 40 RUF TER 6 12 PETH ROF AN ROOF BOX SIZE STING px ACHING RAFT ERS TO FURRING ATTACH FURRING TO TRUSSES w 2 V4 x4 GRK s PER TRUSS L 40 s ATTACHING RAFTERS TO LVL s 6 4 OVER 4 TRUSSES 3 0 HORIZ FROM TO L
11. 34 9 SDNVLSIG AINGNOD L QNO vt Z NMHL b 2 912103515 rn ms IHWME 1HW9uO THWNED 1HW NHE BUHIAA 6 c 1 133HS NO L8VH2 3215 2 OL INIBYNL 335 NI 2 51715 M04 s3apo GN 8758 HINAL AMALLVE NN ENTEN eL J9 04100 wXOPLYVWS ANIGYNL mg IHW NUS 1HNNuD atau AL NOLIONDF INISYAL P AVIS ri K Du r y Se 53104 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 19 Turbine Installation FF h Power Wiring TURBINE POLES C 23 TURBINE TO CONTROLLER WIRE SIZE CHART E TURBINE WIRE MAX _ INCH 8 4 GND 200 1
12. A at Max Power SOURCE CIRCUIT OUTDOOR WIRING TO INVERTER 10AWG USE 2 RHW 2 OR THWN 2 90DEG RATED TEMPERATURE CORRECTION FACTOR FOR 70DEG AMBIENT 0 58 TOTAL CURRENT CARRYING CONDUCTORS 3 FACTOR 1 CORRECTED 40A X 0 58 X 1 23 2 A gt 20 A OUTPUT CIRCUIT OVERCURRENT PROTECTION 15A 90 OF OVER CURRENT PROTECTION RATING 15 X 0 90 13 5A OUTPUT CIRCUIT CONTINUOUS CURRENT 12 9A lt 13 5A AC OUTPUT CIRCUIT MAX CONTINUOUS CURRENT 12 5A MAX INSTANTANEOUS CURRENT 14 37A 3 MIN CONTROLLER OUTPUT CIRCUIT OVERCURRENT PROTECTION 15 A BREAKER 90 OF OVERCURRENT PROTECTION RATING 20 X 0 90 13 5A OUTPUT CIRCUIT CONTINUOUS CURRENT 13 5A lt 15A CONTROLLER OUTPUT WIRING TO POINT OF INTERCONNECTION 12 THWN 2 90DEG C RATED TEMPERATURE CORRECTION FACTOR FOR 40DEG C AMBIENT 0 88 TOTAL CURRENT CARRYING CONDUCTORS 3 FACTOR 1 TOTAL INVERTER INSTANTANEOUS CURRENT 14 37A CORRECTED AMPACITY 25A X 0 88 X 1 22A gt 14 37A AC INPUT CIRCUIT MAX CONTINUOUS CURRENT 12 5A CONTROLLER OUTPUT CIRCUIT OVERCURRENT PROTECTION 15 A BREAKER 90 OF OVERCURRENT PROTECTION RATING 15 X 0 90 13 5A OUTPUT CIRCUIT CONTINUOUS CURRENT 12 5A lt 13 5A CONTROLLER OUTPUT WIRING TO POINT OF INTERCONNECTION 12 THWN 2 90DEG C RATED TEMPERATURE CORRECTION FACTOR FOR 40DEG C AMBIENT 0 88 TOTAL CURRENT CARRYING CONDUCTORS 3 FACTOR 1 TOTAL INVERTER INSTANTANEOUS CURRENT 12 5A CORRECTED A
13. ALVANIZED OR 1 6 mm UNCOATED STEEL EXTENDED AT LEAST 150 mm BEYOND THE EQUIPMENT ON ALL SIDES MUST BE INSTALLED HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Turbine Installation Personal Injury and Property Damage Hazard Do not touch revolving turbine blades or insert objects including sticks and screwdrivers into revolving turbine blades Failure to follow this warning may result in death personal injury or property damage The supplied SMARTBOX Control Equipment Battery Box and batteries not included are installed next to the home s electrical switch box by a certified and trained electrician in accordance to installation directions explained in this Owner s Manual The certified and trained electrician will divert the grid from a pre selected household circuit such as lights see Electrical Manual recommendations to the SMARTBOX Control Equipment AC input terminals The SMARTBOX Control Eguipment AC output terminals are connected to the circuit breaker on the home s electrical switch board The HONEYWELL Wind Turbine captures energy that the SMARTBOX Control Equipment stores in the batteries located in the battery box The SMARTBOX Control Eguipment then manages the supply of electricity to the selected circuit breaker on the home s switch board automatically switches between the grid power and the wind power HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Turbine
14. CONC BALLAST 0844 x 4 43368 TOTAL WT 5308 LOAD PER SF OF ROOF AREA 566 695 3048 o PLAN SCALE 1 4 l 0 CONC BALLAST 24034 Ls y 268 210 C6 2618 2170 CG OD 43348 VERT LOAD 2 43341 VERT LOAD 2 2I6TH LEG 2I6T LEG SCALE V4 1 0 EXTENDED QUAD POD REQUIRES APPROXIMATELY 20 sf LOADING e ROO HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 36 Electrical One Line Drawing Part 1 SYMBOLS LIST EQUIPMENT TAG 1 SHEETNOTE M CIRCUIT BREAKER ROOF or POLE I ni 1 oo DISCONNECT WIND O_O FUSE GENERATOR 2 EARTH GROUND 1 4 GND STAKE SEE TURBINE TO CONTROLLER SIZE CHART ON THIS SHEET MAIN SWITCHBOARD 2 10 THWN 2 6 GND 74 CONDUIT MAX DISTANCE 3 FEET Ea E NN UTILITY St DC WINDTRONICS CHARGE CONTOLLER p INVERTER SYSTEM SMARTBOX Controller i AC 2 12 THWN 2 2 12 THWN 2 46 GND 6 GND CONDUIT 34 CONDUIT 2 4 THWN 2 4 GND 1 CONDUIT L _ 6 ic n i SUB SWITCHBOARD gt 15A 1P 2 12 THWN 2 6 GND 34 CONDUIT LOADS TURBINE TO CONTRO
15. G FROM LOSS OF CONFIDENTIAL OR OTHER INFORMATION OR BUSINESS INTERRUPTION OR ANY SPECIAL INCIDENTAL INDIRECT OR CONSEQUENTIAL DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO DAMAGES FOR LOSS OF PROFITS REGARDLESS OF THE FORM OF ACTION WHETHER IN TORT STRICT LIABILITY CONTRACT OR OTHERWISE ARISING OUT OF OR IN ANY WAY RELATED TO THE DEFECT REPAIR REPLACEMENT OR SHIPMENT OF THE PRODUCT EVEN IF WINDTRONICS KNOWS OF OR SHOULD HAVE KNOWN OF THE POSSIBILITY OF SUCH DAMAGES THE FOREGOING LIMITATIONS EXCLUSIONS AND DISCLAIMERS SHALL APPLY TO HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Warrantry 30 3 THE MAXIMUM PERMITTED BY APPLICABLE LAW EVENT SHALL WINDTRONICS AGGREGATE LIABILITY EXCEED THE AMOUNT ACTUALLY RECEIVED BY WINDTRONICS FROM THE PURCHASER FOR THE PURCHASE OF THE PRODUCT Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you No agent dealer Service Company or other party is authorized to change modify or extend the terms of this warranty in any manner whatsoever LEGAL REMEDIES This warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province CHANGES TO THIS LIMITED WARRANTY WindTronics may change this warranty from time to time When WindTronics makes
16. Honeywell HONEYWELL Wind Turbine Model WT6500 Owner s Manual The T trademark is used under license from Honeywell International Inc Honeywell International Inc makes no representations or warranties with respect to this product or service Thank You Thank you for your purchase of this award winning turbine and welcome to the Age of Renewable Energy Popular Mechanics AWARDS 2009 EDISON AWARDS Thank you for your purchase of the HONEYWELL Wind Turbine It is one of the most advanced wind turbine systems in the world We are proud to offer a cost effective renewable energy technology that will provide you with many years of electric generation from an available and abundant resource the wind Our technology has received the prestigious Gold Edison Award in 2010 and the Breakthrough Technology Award for 2009 from Popular Mechanics By purchasing and installing this product you have demonstrated your desire to reduce carbon dioxide emission and play a role in energy conservation Please take a moment to complete and return to us the Warranty Registration Card Serial Number Model Number Please note that the Warranty depends on the proper installation of the HONEYWELL Wind Turbine Please read this Owner s Manual carefully and always use licensed and trained personnel for its proper installation The HONEYWELL Wind Turbine is manufact
17. Installation 8 Turbine with Electrical Systems HONEYWELL Wind Turbine mounted on ROOFBOX Mount gt o o L x L1 eG 2 9 Typical SMARTBOX Controller connection next to house circuit breakers Figure 2 1 Complete Turbine System Site Selection The key objective of a site evaluation or study is to place the HONEYWELL Wind Turbine so energy generated from the wind is maximized while meeting the local zoning reguirements Key elements to focused on during the site evaluation include 1 High average wind speeds The turbine delivers its best energy performance in areas of high wind speeds This can best be determined by using simple anemometers at the installation site It is recommended that such wind speed data is recorded for as long a period as possible and even better if several seasons are considered When this is not possible rely on published wind data as an estimate for the average local wind speeds Published wind atlas
18. LLER WIRE SIZE CHART TURBINE WIRE MAX DISTANCE FT EMT CONDUIT INCH 10 6 GND 150 3 4 8 4 GND 200 1 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 37 Electrical One Line Drawing Part 2 SHEET NOTES 1 FOR ROOF MOUNT TURBINE LOCAL FIRE DEPARTMENTS MAY REQUIRE DC DISCONNECTS AT THIS LOACTION IF REQUIRED PROVIDE SQUARE D H221NRB 2 LOCATE BESIDE OR BENEATH CONTROLLER 3 LOCATE OUTSIDE OR IN WELL VENTILATED AREA N LOCATE AND BOLT FUSE ON BATTERY POSITIVE TERMINAL EQUIPMENT SCHEDULE TAG EQUIPMENT MANUFACTURE EQUIPMENT DESCRIPTION MODEL PART NO C WINDTRONICS WIND TURBINE NA WINDTRONICS TURBINE INTERCONNECT ENCLOSURE NA Sguare D H D 30AMP 250VDC FUSED DISCONNECT H221NRB 15 250VDC FAST ACTING FUSE CLASS RK1 NA 52 WINDTRONICS TURBINE CONTROLLER NA 6 NA BATTERY ENCLOSURE NA C NA BATTERY DISCONNECT NA LITTELFUSE 100AMP 24V BATTERY FUSE 0298100 2 12V DEEP CYCLE BATTERIES NA SOUARED G D 30AMP 240VAC UNFUSED DISCONNECT DU221RB GD ANY 14AWG 1 PAIR UNSHIELDED NA 2 ANY CAT5E COMMUNICATION CABLE CAT5E GROUND STAKE AND CLAMP ANY NEC CALCULATIONS ALL AMPACITIES CALCULATED AT 75DEG C FOR TERMINATIONS DC VOLTAGE TURBINE Voc 170VDC MAXIMUM DC VOLTAGE 170VDC TURBINE SOURCE CIRCUIT TURBINE Isc 20A Short Circuit TURBINE Imp 12 9
19. MPACITY 25A X 0 88 X 1 22A gt 12 5A BATTERY INPUT CHARGE CIRCUIT MAX CONTINUOUS SOURCE INVERTER CURRENT 72A MAX CONTINUOUS CHARGER CURRENT 50A 60A PEAK 5 minuets BATTERY CIRCUIT OVERCURRENT PROTECTION 100 A FUSE 80 OF OVERCURRENT PROTECTION RATING 100 X 0 80 80A BATTERY CIRCUIT CONTINUOUS CURRENT 72A lt 80A BATTERY CIRCUIT TO CONTROLLER 4 THWN 2 90DEG C RATED TEMPERATURE CORRECTION FACTOR FOR 40DEG C AMBIENT 0 88 TOTAL CURRENT CARRYING CONDUCTORS 2 FACTOR 1 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 38 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 The Honeywell Trademark is used under license from Honeywell International Inc and makes no representations or warranties with respect to this product WindTronics Honeywell International Inc 621 Sprucewood Avenue Windsor Ontario 083 Tell 877 946 3898 www honeywell com Honeywell
20. R 5F OF UPLIFT ON ROOFBOX COMPRESSION LOAD VERTICAL VECTOR 3248 LOAD CARRIED ON 6 33 x 3 OF ROOFBOX TllW s ROOFBOX AREA 6 2 SHOWN WINDTRONICS CORP WIND TURBINE ROOF BOX dryer architectural group ROOF BOX TO BE 6 4 l PLACED OVER 4 TRUSSES LOAD 3248 LOAD VERTICAL TOP CHORD LOADED ONTO 4 TRUSSES m ddd LOAD TO EACH TRUSS 512 VERTICAL LOAD TO ROOF e ROOF BOX architecture interiors design consul tent 220 1 2 washington grand haven michigan 49417 616 846 5400 dryererchezulstar com HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 35 Ballast Mounting A EXTENDED GUADPOD CALCULATIONS ROOF LOAD CALCULATIONS AMERICAN CANYON 44503 I4Omph WIND 4 6O HT dryer architectural group erchitecture interiors design consul tents 220 1 2 washington rand haven michigan 616 846 54 DRAWING INFORMATION N ddd Checked ddd 818 24 0 REVISIONS eet ate 48348 VERT LOAD lt 43348 VERT LOAD gt 4334 VERT LOAD 2 216 1 LEG 2618 2TO 0844 PAD REG D 1084 120 cf 4 03cF OF CONC x BALLAST AREA 1054 5 CONC BALLAST EACH PAD 2 ROOF AREA UNDER PADS 8 8 64st z WT OF TURBINE QUAD POD 8008 W i WT OF
21. T DOIT ETRE RACCORDE LA BATTERIE FAITES ALLUSION AU MANUEL D INSTRUCTION CAUTION DO NOT CONNECT BATTERY NEGATIVE TO GROUND DOING SO WILL BYPASS THE GFI CIRCUIT P RECAUTION NE RACCORDEZ PAS DE BATTERIE NEGATIVE POUR FONDER L ACTION EVITERAAINSI LE CIRCUIT GFI Figure 2 11 Turbine Connection Location in SMARTBOX Controller Turbine Over Current Protection The NEC CEC requires the turbine circuit to be protected with a device rated for 125 of the rating of the circuit The DC rated fuse or circuit breaker between the turbine and the SMARTBOX Controller must have a maximum size of 15 the maximum current rating of the Smart Box Smart Box from short circuits and to provide a means of disconnecting the it REVERSE POLARITY DAMAGE Before making the final DC connection or closing the DC breaker or disconnect check cable polarity at both the battery and the Smart Box Positive must be connected to positive Negative must be connected to negative A WARNING SHOCK OR FIRE HAZARD A WARNING Over current protection must be installed to protect the HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Turbine Installation 21 Control Wiring 91 210351 2 04u09 DHO ng LHM NYD 621 O3 53000
22. VL WINDTRONICS CORP WIND TURBINE ROOF BOX dryer architectural group architecture interiors design consultants 220 1 2 washington grand haven michigan 49417 616 646 5400 dryerercheazulstor com DRAWING INFORMATION Drawn ddd Checked ddd Date 12 14 04 PROJ No 04 54 REVISIONS Sheet ROOF BOX DOMETRU HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 34 ROOFBOX with QUADPOD Mounting 084 EXTENDED QUAD 20 84 01017 ROOF BOK METEEAMET UNS MORE THAN 218 MAST SET VERTICAL DIAGONAL LEG SET 45 TO MAST PREVAILING WIND TURBINE ROOF BOX MATERIALS SHINGLES TO MATCH EXISTING 4 WATERSHIELD FULL COVERAGE V2 OSB SHEATHNG 2x4 RAFTERS SPF 20 2x4 TREATED WD FURRING 3 4 x 5 h LVL x4 RIDGE BD L 40 s ATTACHING RAFTERS FURRING ATTACH FURRING TO TRUSSES w 2 l 4 x4 GRK s PER TRUSS 4 5 084 3 00 8 94 08 3 06 3248 3248 COS 45 THE 1241 LOAD I5 DELVELOPED FROM THE FULL EXPOSURE 715095 OF THE TURBINE 22159 3 SECOND GUST OF WIND 45 2 B THE SECOND GUSTS DO NOT OCCUR WINTER 8 7 SNOW LOAD TURBINE LOAD DO NOT NEED TO BE CONSIDERED CUMULATIVE N UPLIFT LOAD 3248 LOAD 6 CARRIED ON 622 3 OF ROOF e 52 UPLIFT 6 ROOFBOX I
23. Wind Turbine HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 13 Turbine Installation Turbine Component Diagram circuit breaker grid AC disconnect o HONEYWELL Wind Turbine e SMARTBOX Controller AC output disconnect SMARTBOX Controller turbine disconnect FA SMARTBOX SS ControllerAC output gt a x 4 4 battery box with battery fuse 4 disconnect home outlet Figure 2 4 Turbine Components HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Turbine Installation 14 The SMARTBOX Controller The SMARTBOX Controller contains all the electronic controls needed to integrate to the home s electrical switch board circuits The SMARTBOX Controller is housed in a NEMA 3R enclosure and must be mounted on the wall next to the home s electrical switch board The SMARTBOX has an LCD display and four operational buttons Details of the function of these buttons is listed in the SMARTBOX Controller Manual Please read SMARTBOX Controller Manual and always consult and use a certified and trained electrician for connections and
24. ZARD WARNING Disconnect turbine and battery circuits before wiring Turn off all power before wiring Failure to follow safety warning could result in serious injury and or death Personal Injury and Property Damage Hazard STOP If you plan to connect the HONEYWELL Wind Turbine to any controller other than the SMARTBOX Controller immediately cease the installation of the WYS Geg HONEYWELL Wind Turbine Failure to follow this warning will void the HONEYWELL Wind Turbine warranty and may result in death personal injury or property damage including damage to the HONEYWELL Wind Turbine PROFESSIONAL INSTALLATION reguired Installations must meet all local electrical codes Installations for the eguipment should only be performed by a gualified electrician or a licensed and trained WindTronics installer The wiring connections between a mounted HONEYWELL Wind Turbine Battery Box and SMARTBOX Controller is relatively simple The following diagram details and specifies the wire gauges required in this installation It is strongly recommended that a certified and trained electrician performs all the electrical connection All electrical systems must be grounded in accordance to the National Electric Code or in Canada the Canadian Electric Code CEC and local standards Please refer to the SMARTBOX Controller Manual for full details on wiring connecting and commissioning of the HONEYWELL
25. changes to the warranty it will post them at www windtronics com The warranty that shall apply to a product shall be the warranty posted at the Website at the time the product is purchased It is the Purchaser s responsibility to check the Website to see if the warranty posted there is different than the warranty stated herein GOVERNING LAW If the Purchaser purchases the product in the United States of America this warranty is governed by the laws of the State of Michigan and the applicable federal laws of the United States If the Purchaser purchases the product in Canada this warranty is governed by the laws of the Province of Ontario and the federal laws of Canada applicable therein In either case the application of the United Nations Convention on Contracts for the International Sale of Goods is expressly excluded HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 31 Turbine Installation Drawings For Information on See Pole Mount 32 ROOFBOX Mount 33 ROOFBOX with GUADPOD TM 34 Mounting Ballast Mount 35 One Line Drawing 36 37 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 32 Pole Mount wyf ryu AL Doe AR pep SSS SS qa Py ER Rp m epe LIS ET o gu Fi EL ENYD EM _ GUESS T Les ae TH aL E Dos h n mon T i J
26. cs damage caused by severe weather or acts of God or any other act or event beyond the control of WindTronics and 4 Ifthe product has been exposed to winds exceeding 100 mph 160 km per hour has been subjected to abnormal physical thermal or electrical stress WARRANTY REGISTRATION The Purchaser must maintain proof of purchase or register the product for warranty coverage within sixty 60 days after purchase Purchaser can register the product for warranty coverage online at www windtronics com or by completing and returning the warranty registration card located the back of the owner s manual warranty claims made on a product that has not been registered will be denied unless proof of purchase can be provided DISCLAIMERS APPLICABLE TO ALL WARRANTIES EXCEPT FOR THE EXPRESS LIMITED WARRANTY SET FORTH ABOVE WINDTRONICS EXPRESSLY DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS WARRANTIES ADDITIONALLY TO THE EXTENT PERMITTED BY APPLICABLE LAW EACH AND EVERY IMPLIED WARRANTY THAT MAY APPLY TO THE PRODUCT INCLUDING WITHOUT LIMITATION THE WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND FREEDOM FROM ENCUMBRANCES ARE LIMITED IN DURATION TO THE FIVE YEAR LIMITED WARRANTY PERIOD WINDTRONICS EXPRESSLY DISCLAIMS ALL LIABILITY FOR BODILY INJURY OR DEATH THAT MAY OCCUR DIRECTLY OR INDIRECTLY BY USE OF THE PRODUCT LIMITATION OF LIABILITY EVENT SHALL WINDTRONICS BE LIABLE FOR ANY DAMAGES RESULTIN
27. d zoning codes Follow the electrical connections and commissioning procedures in the SMARTBOX Controller Manual for the wind turbine start up operations and maintenance The label below is provided to indicate the location of the AC POWER disconnect switch Please cut out and place near the SMARTBOX Controller where an electrician and service personnel can easily see it ATTENTION To Disable Wind Turbine Disconnect AC Power Note AC Power Disconnect Box is located at Disconnect amp Lock Out AC Power per NFPA 70E and OSHA Requirements before servicing and or maintance Windtronics Inc 621 Sprucewood Avenue Windsor N9COB3 Canada There are no parts in the HONEYWELL Wind Turbine that require lubrication or scheduled maintenance Please follow the manufacturer of the battery for its installation operation and maintenance Please contact WindTronics Service with any questions 1 877 946 3898 The SMARTBOX Controller has built in automatic software fail safe procedures that serve as automatic safety turbine shut down modes However the AC Power MUST be disconnected at the Disconnect AC Power Box as noted in the above label Furthermore the E Stop on this AC Power Disconnect must be in the OFF position whenever maintenance and any other mechanical or electrical work is to be performed on this turbine The HONEYWELL Wind Turbine is grounded to meet lightning surges If noise or vibrati
28. e wiring compartment grounds the negative conductor of the turbine and provides turbine ground fault protection Only a Littelfuse 0312 500HXP or equivalent fuse should be used as a replacement HAZARD WARNING DO NOT connect the battery negative to ground NEC reguirements specify that the battery negative ground must be done only through the 1A fuse Bonding the battery negative to ground will disable the turbine s ground fault protection and will result in improper operation The battery compartment should be grounded if made of metal SHOCK AND FIRE HAZARD WARNING Fuses must only be replaced by qualified service personnel such as a certified electrician or technician For continued protection again risk of fire replace only with the same type and rating of fuse Failure to follow this warning may result in death personal injury or property damage A SHOCK HAZARD A WARNING Disconnect wind and battery circuits before removing the grounding connections or before removing or installing the fuse Wait at least 5 minutes for the internal circuitry to dis charge before servicing the unit Failure to follow this warn ing may result in death personal injury or property damage Even though the wind turbine is grounded at the service manual it must also be grounded at the base of the mounting pole GUADPOD Mount or TriPod Grounding at these mounts may prevent electric shock and voltage surges Proper mount grounding
29. ecting to a local electric grid is not possible Its unique and high efficiency design enable it to work in very low wind areas starting at 2 miles per hour mph and much higher to 38 mph Please follow the Site Selection guidelines for optimal installation The HONEYWELL Wind Turbine is an electric generator Only licensed and trained personnel can perform the following installation and maintenance functions Open and work on the SMARTBOX Control Equipment Open and work on the Junction Box at the turbine Apply any torque to any of the turbine s fasteners The installation directions include recommendations of a variety of options Installation must be approved and certified by your local Professional Engineer PE and the installer must acguire all the necessary permits from the local authorities prior to installation Your installer must use only proper grounding methods as stipulated by the NEC or CEC if in Canada The HONEYWELL Wind Turbine is an electric generator Therefore high voltage is generated within the system Be sure to only use installers and maintenance professionals to perform work on this turbine Failure to complete and mail in the registration card will affect the Warranty Failure to use a licensed and trained installer or follow local codes will adversely affect the warranty coverage and possibly void your warranty Please contact WindTronics if there is any doubt or concern regarding this el
30. ectric generator or its installation 1 877 946 3898 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Introduction 4 Kw Lift Point The recommended lift point is shown in the photograph below Ar HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 5 Turbine Installation EEg Or i Turbine Mounting and Wiring Chapter 2 describes turbine installation mounting options and electrical wiring For Information on See Introduction 6 Site Selection 8 Mounting Options 10 Turbine Wiring 12 SMARTBOX Controller 14 Battery Box 15 Junction Box 16 Turbine Wiring Overview 18 Grounding 22 Operation 23 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Turbine Installation Turbine Mounting Introduction Hazardous voltages currents or other conditions that could cause serious bodily injury or death exist in this equipment or may be associated with its use Personal Injury and Property Damage Hazard STOP If you plan to connect the HONEYWELL Wind Turbine to any controller other than the SMARTBOX Controller immediately cease the installation of the 5 HONEYWELL Wind Turbine The HONEYWELL WI Wind Turbine can only be connected to SMARTBOX TM Controller or other controller pre approved writing by WindTronics Failure to follow this warni
31. ered Notice shall be in writing or by telephone Notices by telephone shall be made by calling 877 946 3898 and written notices shall be sent to WindTronics Inc 621 Sprucewood Avenue Windsor Ontario N9C 0B3 Attn Customer Service Warranties The Purchaser must provide WindTronics the following 1 the date the defect was discovered 2 evidence of the defect including without limitation photographs and a verbal written description of the defect 3 the serial number of the product 4 the original purchase date of the product 5 the location of the product and 6 the name address and phone number of the party making the warranty claim We reserve the right to an on site inspection by an authorized service representative The Purchaser is required to provide adequate access to the product for any such repair or inspection Subject to the terms and conditions contained in this document a Factory Authorized Dealer Service Center will repair the product For the first two 2 years there will be no charge for parts labor or the freight costs for parts necessary to repair the product After the second year the warranties will only cover replacement parts If it becomes necessary for the product to be shipped to the Factory Authorized Dealer Service Center the Purchaser shall be responsible for transporting the product to and from the Factory Authorized Dealer Service Center Additionally reasonable travel charges of the re
32. es can contain very useful HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 9 Turbine Installation s ey comparative data for a region or a specific location However be very careful when relying only on this information as such data quite often tends to be measured at very high altitudes and may not be useful at lower and more practical heights 2 As a general rule it is best to install the turbine at the highest permissible position and far removed in proximity to trees and other adjacent buildings or structures 3 Always take into consideration all possible safety conseguences of the turbine installation at the local site Wind Power Classification Wind Resource Wind Power Wind Speed Wind Speed Power Potential Density 50 m 50 at 50 Class Wim ms mph 3 4 14 3 15 7 4 0 7 15 7 16 8 5 16 8 17 9 6 J 17 9 19 7 7 J 19 7 24 8 25 NezL National Renewable Energy Laboratory Figure 2 2 Wind Map for USA There are several options for the installation of the HONEYWELL Wind Turbine The turbine may be installed using a pole aQUADPOD Mount on a flat roof with a ballast a QUADPOD Mount on a pitched roof with ROOFBOX Mount These are described in the next section Building codes and installation requirements vary considerably between various townships cities states and countries Make sure that all required local permits are obtained BEFORE begi
33. ipping Contents 2 Before Installing the HONEYWELL Wind Turbine 3 EL PT PETER 4 2 Turbine Mounting and Wiring Turbine Mounting 6 Turbine with 1121121 8 97 cu uuu u EUREN 8 Mo nting OP OT iirinn 10 Pole fn dene 11 GUADPODTM au vene onu a EEEE 11 ROOFBOXTM Montu 11 Balast Gyd 12 Turbine Wiring NY RS ENIM 12 The SMARTBOX Controller a 14 The Battery desea 15 Recommended Battery 15 Ti eJ nctuom Box NER 16 Junction Box Block 17 Turbine Wiring Overview Diagram 18 DC Power Wiring 19 Turbine Wiring and 19 Turbine Current Rating and Wiring 19 Turbine Over current Protection
34. ng will void the HONEYWELL Wind Turbine warranty and may result in death personal injury or property damage including damage to the HONEYWELL Wind Turbine e PROFESSIONAL INSTALLATION required After following the unpacking procedures included in the wind turbine package it is required that only licensed and trained personnel perform the installation and maintenance of the wind turbine In general the installation consists of mounting the turbine on suitable and approved mounting hardware The installation procedure include recommendations for the mounting options They must be approved and certified by your local Professional Engineer PE and a licensed and trained installer must acquire all the necessary permits from the local authorities prior to installation The following illustration shows the HONEYWELL Wind Turbine installation on a ROOFBOX Mount see details on page 14 The turbine is mounted to the ROOFBOX Mount using a QUADPOD Mount see details on page 14 The anemometer and the Junction Box are mounted by a certified and trained electrician to one of the support legs of the QUADPOD Mount Please be aware of the warning label on the HONEYWELL Wind Turbine shroud that states the following WARNING TURBINE BLADES ARE NECESSARY FOR THE PROPER OPERATION THEY ARE EXPOSED MOVING PARTS ACCIDENT HAZARD WHEN MOUNTING ON OR OVER A COMBUSTIBLE SURFACE A FLOOR PLATE OF AT LEAST 1 43 mm lt gt CAUTION G
35. nning installation In all cases installation must be conducted by a licensed and trained professional contractor and electrician In some locations the local electric utility may have strict regulations about renewable energy technologies such as this wind turbine and other interconnect agreements and therefore it is highly recommended that they are also contacted BEFORE installation HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Turbine Installation 10 Mounting Options Personal Injury and Property Damage y AUAN Do not install the HONEYWELL Wind Turbine in a location that is accessible to children or pets Failure to follow this warning may result in death personal injury or property damage A Personal Injury and Property Damage Hazard rhe HONEYWELL Wind Turbine must be mounted by licensed and trained personnel only with the use of all appropriate hardware Failure to follow this warning will void the HONEYWELL Wind Turbine warranty and may result in death personal injury or property damage including damage to the HONEYWELL Wind Turbine The schematic below shows the installation options available for the HONEYWELL Wind Turbine Whichever mounting option is chosen should be approved by a local Professional Engineer PE All of the options listed have been rated by our Professional Engineer Please refer to the following designs and their included specifications QUADPOD
36. on is detected and if the turbine s blades rotate very slowly under extremely windy conditions turn turbine off and please contact WindTronics Service at 1 877 946 3898 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Turbine Installation 24 cc 1 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 25 Specifications kwa aww c b Y lD Dl iD ii Y i Specifications For Information on See Technical Specification 25 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Specifications 26 Technical Specifications Model WT 6500 Specification Rated Power Output 1500 W at 13 9 m s 31 mph Weight 79 5 Kg 175 pounds Rotor Diameter 1 82 m 6 feet Type Blade Tip Power System Constantly Facing Wind Dynamic Aerodynamic Deflectors Blades 20 Glass Filled Nylon 10 short and 10 long Rate Rotation 150 RPM Shut Down Speed 165 or 38 mph Tip Speed at 160 RPM 14m s 32 m s Generator Perimeter Tip Permanent Magnet Stator System Yaw Control Dynamic Grid Feeding Hybrid Braking System Electromagnetic Cut In Wind Speed 0 9 m s 2 mph Rated Wind Speed 13 9 m s 31 mph Survival Wind Speed 63 m s 140 mph Sound Power Lever Less Than 35 dB Added at 13 5 m s 30 mph DATA SUBJECT TO CHANGE WITHOUT NOTICE HONEYWELL Wind T
37. onsult and use a certified and trained electrician for connections and service i We only recommend using TWO 12V 100Ah flooded deep cycle marine grade batteries Recommended Battery Type HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Turbine Installation 16 E The Junction Box The HONEYWELL Wind Turbine is an electric generator As discussed in the technology description the electricity is generated at the stators due to the high speed traversing of the permanent magnets at the blade tip and wheel rim The electrical output of each stator is bused to the Junction Box that is mechanically attached to the mount section nearest the turbine The Junction Box contains the interface electronics of the stators to which all the wire connections are made in the field by a certified and trained electrician to the SMARTBOX Controller located near the home s electrical switch board The Junction Box is a NEMA 4X enclosure to which a steel enclosure that houses an 1900 W stainless steel resistor is attached The resistor is named the Dump Load and is used in various operating and safety regimes as defined by the controlling software of the HONEYWELL Wind Turbine An anemometer that measures the wind speed and direction is also attached to the Junction Box Please refer to the SMARTBOX
38. pair person may be assessed in cases where the product is in a remote location In the event the Purchaser is unable to obtain satisfactory service from a Factory Authorized Dealer Service Center the Purchaser should notify the WindTronics Customer Service Department If we determine that repairs are not feasible due to functional defect we reserve the right to provide a replacement part or product in lieu of repair We will replace with HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 29 Warrantry a part of value egual to the original purchase In such event reasonable costs for of the defective product and delivery and installation of the replacement product will be the responsibility of the Purchaser All replaced parts and products shall become the property of WindTronics on the date the part or product is replaced LIMITATIONS AND EXCLUSIONS ON LIMITED WARRANTY This limited warranty will not apply under any of the following circumstances 1 If any part of the product has been altered or modified by anyone other than an authorized representative of WindTronics 2 lf any part of the product has not been installed operated repaired or maintained in accordance with the product s instructions 3 If any part of the product has been the subject of misuse misapplication improper maintenance or repair damage caused by the fault or negligence of anyone other than an authorized representative of WindTroni
39. r attached to the HONEYWELL Wind Turbine Improper installation adjustment alteration service maintenance or use can cause fire electrical shock or other conditions which may cause death personal injury or property damage The use of a licensed and trained professional for the installation and maintenance of the HONEYWELL Wind Turbine is required HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 10 11 12 13 14 DO NOT CONNECT THE HONEYWELL WIND TURBINE TO ANY CONTROLLER OTHER THAN THE SMARTBOX Controller OR OTHER CONTROLLER PRE APPROVED IN WRITING BY WINDTRONICS WARNING Failure to follow this warning will void the HONEYWELL Wind Turbine warranty and may result in death personal injury or property damage including damage to the HONEYWELL Wind Turbine Choose a very calm nearly no wind day for the installation Follow the installation procedures contained within this Owner s Manual and all safety codes Follow the National Electric Code NEC and your local building zoning and zoning codes In Canada follow the Canadian Electrical Code CEC Only licensed and trained personnel should move and lift the HONEYWELL Wind Turbine The HONEYWELL Wind Turbine should only be moved using standard hoists and hydraulic lifts Appropriate protective personal equipment such as hard hat work gloves safety glasses and closed toe work shoes should be worn when installing
40. ter wind speed and direction outputs to the HONEYWELL Wind Turbine SMARTBOX Control Equipment The SMARTBOX Control Equipment contains custom electronic battery charging circuits an inverter and a transfer switch The SMARTBOX Control Equipment also employs a microprocessor which is programmed for optimal electric energy extraction from the wind battery charge management and automatically controls the transmission of electricity via the transfer switch from the Grid switch board or the attached battery Not included Shipping Contents 1 One HONEYWELL Wind Turbine 2 Two 2 Wind Deflectors with four 4 brackets attached and eight 8 20 S S locknuts 3 One 1 Deflector installation instruction manual 4 One 1 Wind Turbine inspection certificate Tag 5 One 1 Junction Box assembly including Wire harness connected to Wind Turbine which includes two 2 14 AWG Black wire and one 1 12 AWG Green wire Davis instrument anemometer model 7911 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 3 Introduction Before Installing the HONEYWELL Wind Turbine IMPORTANT Please take note that the HONEYWELL Wind Turbine is a proprietary wind driven electric generator It is designed to displace annual electric consumption by connecting it to the electric switch board in the proper procedures described in this Owner s Manual It may also be used on a stand alone installation where conn
41. the HONEYWELL Wind Turbine Only licensed and trained personnel can perform the following maintenance functions on this HONEYWELL Wind Turbine Open and work on the SMARTBOX Control Equipment Open and work on the Junction Box at the turbine Apply any torque to any of the turbine s fasteners The installation directions include recommendations of a variety of options Installation must be approved and certified by your local Professional Engineer PE and the installer must acguire all the necessary permits from the local authorities prior to installation Your installer must use only proper grounding methods as stipulated by the NEC or CEC if in Canada The HONEYWELL Wind Turbine is an electric generator Therefore high voltage is generated within the system Be sure to only use installers and maintenance professionals to perform work on this turbine Failure to complete and mail in the registration card will affect the Warranty Failure to use a licensed and trained installer or follow local codes will adversely affect the warranty coverage and possibly void your warranty NOTE TO INSTALLER This Owner s Manual should be left with the owner of the HONEYWELL Wind Turbine HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 V Table of Contents Table of Contents Safety Instructions I 1 Introduction Product Description 2 Sh
42. urbine WT6500 Owner s Manual Rev 10 27 Warranty Information HONEYWELL Wind Turbine WT6500 Owner s Manual Rev 10 Warrantry 28 5 Year Limited Warranty LIMITED WARRANT Y Subject to the terms below WindTronics Inc WindTronics warrants its products against defects in materials or workmanship under normal use consistent with product instructions for a period of five 5 years from the date the original purchaser the Purchaser purchases the product This warranty extends only to the Purchaser and cannot be assigned to any other party If warranted products contain defects covered under this warranty WindTronics obligation shall be limited to in WindTronics sole and absolute discretion repairing or replacing the defective parts Repaired or replaced parts are warranted for the remainder of the original warranty period WARRANTY CLAIMS No rights may be exercised under this warranty unless the Purchaser registers the product for warranty coverage within sixty 60 days after purchase or provides proof of purchase Purchaser can register the product for warranty coverage online at www windtronics com or by completing and returning the warranty registration card included with the product in which case the product will be considered registered as of the postmark date on the warranty registration card Notice of any defect covered under this warranty must be given within thirty 30 days of the date the defect is discov
43. ured by WindTronics Please contact WindTronics at 621 Sprucewood Avenue Windsor Ontario N9C 0B3 877 946 3898 The Honeywell Trademark is used under license from Honeywell International Inc Honeywell International Inc makes no representations or warranties with respect to this product HONEYWELL Wind Turbine WT6500 Owner s Manual Rev10 HONEYWELL Wind Turbine WT6500 Owner s Manual Rev10 Safety Information Safety Information PLEASE READ THESE INSTRUCTIONS AND THE ENTIRE MANUAL PRIOR TO INSTALLATION INSTALLATION OF THIS WIND TURBINE CAN ONLY BE PERFORMED ALICENSED AND TRAINED PROFESSIONAL Safety Icons The following symbols identify dangers associated with the installation use or ownership of the HONEYWELL Wind Turbine When you see the symbols be aware of the protocol for personal injury or property damage WARNING indicates a hazard that could result in death WARNING personal injury or property damage indicates a hazard that could result property a IMPORTANT PLEASE TAKE NOTE e PROFESSIONAL INSTALLATION REQUIRED Q TIP Helpful information to ease the installation Important Safety Instructions This Owner s Manual contains important instructions for HONEYWELL Wind Turbine installation and maintenance Please save it Read the entire Owner s Manual prior to installation and follow all warnings and cautions included in the Owner s Manual and o
Download Pdf Manuals
Related Search