Home Automation OMNITOUCH 53A00-1 User's Manual
Contents
1. INPUT SWITCH ai MEZZASMK New Hisvk RED BLACK YELLOW GREEN BLACK lt p RED GREEN YELLOW CONNECT ENDS OF SUPPLIED LE SP END OF THE POWER COMMUNICATION SUPPLIED CABLE CABLE FROM THE CONTROLLER PLUGS INTO J1 a wa Omni Ile Lumina OmniPro Il and Lumina Pro Connections CONNECTING TO OMNILT Connect the Yellow and Green wires from the touchscreen to the YEL and GRN terminals under the section marked CONSOLE on the controller respectively Connect the Red and Black wires from the touchscreen to the 12V and GND terminals under the section marked AUX on the controller respectively A maximum combination of 4 touchscreens and co2. USB UPDATE PORT Load the update file on a USB thumb drive Plug the thumb drive into the USB Update Port on the OmniTouch 5 7 Touchscreen When the USB drive is plugged into the port the touchscreen will read the files on the root directory of the drive and display any applicable update files Select the desired file from the list and then press the Next button Follow the instructions on the screen 12 SPECIFICATIONS Size Backbox cutout 5 625 W x 5 125 H Faceplate 6 W x 5 5 H LCD View Area 4 626 W x 3 492 H Voltage Operating Voltage 10 24 VDC Maximum Current Consumption at 12 VDC 300 mA based on Maximum Cable Length as defined in Table 1 Maximum Current Consumption at 24 VDC 200 mA based on Maximum Cable Length of 800 feet Maximum CAT 5 Cable Length AT 24 VDC 800 feet 13
3. Na HA Home Automation Inc Model 53A00 1 OmniTouch 5 7 Touchscreen with Video Installation Manual Document Number 53100 1 Rev A June 2007 FCC NOTICE This device complies with FCC Rules Part 15 Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Verified to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules Copyright 2007 Home Automation Inc ALL RIGHTS RESERVED PLANNING It is very important to plan where the OmniTouch 5 7 Touchscreen will be installed and the gauge type of wire you will use for the installation The touchscreen can be connected directly to the HAI controller if video is not being used However if video is being used the touchscreen must be connected to the HAI Touchscreen Hub The HAI Touchscreen Hub can also be used if you are connecting multiple touchscreens up to 8 In selecting a place to mount the touchscreen be sure to avoid an area where studs plumbing or electrical wiring may be located behind the wallboard It should be mounted so that the display is at or slightly above eye level Wiring to the HAI Controller When connecting the touchscreen directly to the HAI controller run the power communications cable as determined by Table 1 from the controller location to touchscre
4. have a unique address The default address setting of the touchscreen is 1 When power is first connected to the touchscreen if the touchscreen isn t addressed properly other consoles or touchscreens already occupy the touchscreen address or isn t communicating with the controller the following page is displayed NO CONTROLLER DATA if 3 6 9 ub To assign an address to the touchscreen press and hold the HAI logo for three seconds The Touchscreen Address page is displayed Touchscreen Address Brightness Contrast Video Disabled rk Oe Od Touchscreen t Address 1 v gt f This page allows the installer to adjust the brightness and contrast of the touchscreen enable or disable video and assign the touchscreen address 10 Brightness and Contrast Press the up arrow button to raise the current brightness or contrast setting Press the down arrow button to lower the current setting Video If the touchscreen is connected to the HAI Touchscreen Hub with Video Encoder press the up arrow button to enable video on the touchscreen If not press the down arrow button to disable video When Video is enabled the Video icon will be displayed on the Home page If it is disabled the Setup button will be displayed instead Touchscreen Address Use the up arrow and down arrow buttons to set the touchscreen address When complete press the exit button in the lower right corner to sav
5. the touchscreen by hanging the top of the faceplate on the top edge of the touchscreen then gently snapping the bottom onto the touchscreen REMOVING THE TOUCHSCREEN After installation if it is necessary to remove the touchscreen from the wall turn retaining flange screws 1 turn counterclockwise Note Do not turn the retaining flange screws more than 1 full turn counterclockwise otherwise the retaining flange may fall off into the wall CONNECTING TO OMNI Ile LUMINA OMNIPRO II AND LUMINA PRO Connect the Yellow and Green wires from the touchscreen to the A and B terminals under the section marked CONSOLE on the controller respectively Connect the Red and Black wires from the touchscreen to the 12V and GND terminals under the section marked AUXILIARY on the controller respectively A maximum combination of 8 touchscreens and consoles can be used with Omni IIe or Lumina and a maximum combination of 16 with OmniPro II or Lumina Pro NOTE Do not exceed the maximum current limitation of the controller If more than 2 touchscreens are used the additional touchscreens must be powered from an external power supply or HAI Touchscreen Hub THE EXTERNAL POWER SUPPLY MUST BE GROUNDED TO THE CONTROLLER EARTH GROUND TO AVOID DAMAGE TO THE TOUCHSCREEN TE CMT TUT ATT Bees e eeeweeseeeerieeei g
6. e the settings and exit Once the touchscreen is properly configured and communicating with the controller other configuration items may be configured using the Screen Setup page To access the Screen Setup page from the Home page if Video is disabled or the System page touch the Setup icon See the Touchscreen User s Guide 53R00 1 for additional information on these items Note In the event of an AC Power failure and the HAI controller is running on backup battery power the touchscreen display will be lowered to its lowest viewable setting Do not try to adjust the brightness and contrast levels When AC Power is restored the touchscreen display will automatically return to its correct settings RESETTING THE TOUCHSCREEN If for any reason the touchscreen needs to be reset remove the faceplate and press the reset button marked SW1 on the circuit board to the right of the LED 11 UPDATING THE TOUCHSCREEN The USB Update Port on the OmniTouch 5 7 allows you to update the touchscreen with the latest firmware and screens This allows you to take advantage of new touchscreen features and new screens that support features of updated controller firmware The Update Port is a USB port in the lower right section of the touchscreen OmniTouch 5 7 Update Utility Select Upgrade File HAI OT57S V 210 DEFAULT 57Z 4 HAI OT57S_ V 210 GOLD 57Z
7. een Hub Installation Manual for more details Connections When connecting a touchscreen to the HAI Touchscreen Hub insert the 8 position modular cable coming from the touchscreen into one of the RJ 45 connectors J1 J8 on the HAI Touchscreen Hub See the HAI Touchscreen Hub Installation Manual for complete installation instructions INSTALLATION 1 Make the cutout for the touchscreen Hold the template Installation Template 53A10 1 against the wall so the top edge is at the appropriate height and parallel to the floor Using a Punch or similar instrument punch through the center of each tick mark on the template Drill a 1 4 hole at each punch mark Using a pencil draw a line around the quadrant of each hole as shown as shown Carefully cut along the pencil line DO NOT OVERSIZE THIS CUTOUT Figure 1 2 Remove the faceplate Remove the faceplate from the touchscreen by grasping the top and bottom edges of the faceplate and carefully lifting it away from touchscreen backbox Note After installation the faceplate may be removed by placing a flat blade screwdriver in one of the slots on the bottom of the faceplate and gently lifting to release the latch on the respective side Repeat by using the slot on the opposite side f i FACEPLATE BOTTOM VIEW LATCH RELEASE SLOTS f Figure 2 3 Remove the touchscreen assembly from
8. en location A minimum of 4 wires is required for operation 2 for power and 2 for communications The required distance between the controller and the touchscreen will determine the wire gauge type you should use To prevent the touchscreen from drawing more than the specified maximum current from the controller s power supply do not exceed the Maximum Cable Length based on the wire gauge type per the table below Table 1 MAXIMUM CABLE LENGTH BASED ON WIRE GAUGE TYPE Wire Solid Number of positive Number of ground Maximum Cable Gauge Stranded conductors conductors Length feet 24 solid 1 1 113 24 solid 2 2 227 24 solid 3 3 340 22 solid 1 1 180 22 solid 2 2 360 22 stranded 1 1 166 20 solid 1 1 287 20 stranded 1 1 267 18 solid 1 1 456 18 stranded 1 1 420 16 solid 1 1 724 16 stranded 1 1 669 Table 1 If cable with multiple conductors is used such as Cat 5 cable it is possible to connect multiple conductors together to achieve greater distance For example using only one of the 24 gauge conductor in the Cat 5 cable for power 1 for positive and 1 for ground the maximum distance between the controller and the touchscreen is 113 feet If you were to connect 2 of the 24 gauge conductors together 2 for positive and 2 for ground the maximum distance between the controller and the touchscreen is then 227 feet If you were to connect 3 of the 24 gauge co
9. nductors together 3 for positive and 3 for ground the maximum distance between the controller and the touchscreen is then 340 feet Wiring to the HAI Touchscreen Hub When connecting the touchscreen to the HAI Touchscreen Hub a Cat 5 4 pair cable is required for operation The Cat 5 cable provides power communications and the video signal from the HAI Touchscreen Hub to the touchscreen Run the Cat 5 cable between the HAI Touchscreen Hub location and the touchscreen location The maximum distance between the controller and each touchscreen is 800 feet Terminate both ends of the Cat 5 cable with an 8 position modular connector as if to make a standard network cable Note When calculating the distance between the Touchscreen Hub and a touchscreen you must subtract the distance between the Touchscreen Hub and the HAI controller from the total distance For example if the Touchscreen Hub is 100 feet from the controller the maximum distance between the Touchscreen hub and each touchscreen is 700 feet CONNECTING TO THE HAI TOUCHSCREEN HUB When used each OmniTouch Touchscreen connects to the HAI Touchscreen Hub The HAI Touchscreen Hub provides power communications and the video signal to the touchscreen Each HAI Touchscreen Hub can support a maximum of 8 touchscreens Note When more than 8 OmniTouch Touchscreens are used a second HAI Touchscreen Hub with Video Encoder if video is being used is required See the HAI Touchscr
10. nsoles can be used with OmniLT NOTE Do not exceed the maximum current limitation of the controller If more than 1 touchscreen is used the additional touchscreens must be powered from an external power supply or HAI Touchscreen Hub THE EXTERNAL POWER SUPPLY MUST BE GROUNDED TO THE CONTROLLER EARTH GROUND TO AVOID DAMAGE TO THE TOUCHSCREEN T e HEHH Ld RED BRN HONE fa SMK o eM TBL TH A A 2 2 A 2 2 Z 2 2 2 2 A A H ij II HHHH j HHI END U RROT bert l ENSOLE cae n ik ciety Uor he E z x Zz a 2 i mi 3 w x xva gt o kaai BLACK _ EE RED GREEN YELLOW Sl CONNECT ENDS OF SUPPLIED CABLE TO CORRESPONDING ENDS OF THE POWER COMMUNICATION SUPPLIED CABLE CABLE FROM THE CONTROLLER Alls PLUGS INTO J1 S Z gt OQ OmniLT Connections ADDRESSING THE TOUCHSCREEN OmniTouch touchscreens are connected to the same communications bus as HAI consoles Each console and touchscreen must
11. the HAI Touchscreen Hub terminate the cable with an 8 position modular connector as if to make a standard network cable 6 Connect the communications cable to the touchscreen Insert the 8 position modular cable into the RJ 45 connector J1 on the touchscreen through the cutout in the touchscreen backbox see Figure 6 4 SH 200p kA Figure 6 7 Install the touchscreen assembly a Align the tabs on the touchscreen assembly with the slots on the backbox Figure 7 b Swing the touchscreen assembly in place and secure to backbox using screws that were removed in Step 3 lt Va y v v Lat y v y i J T H v J v v v y i v No v v J A y J v y 7 v 7 F l y J Ny ma J SES _ eee N NU lt v v y Le q dee v v X AS Se N J v i y 7 f y v y 4 7 r m v v E VE J v J 1 v l Vv y 1 y v l 7 I i I v v y l v J w i Pe A CH N Ny l aes J v Za W l f l A j 1 Z 1 oly J y A Ce I v y f i v y v J v l Vv Na Ng l J v 7 i y v l v Vv y y 7 y Figure 8 8 Install the touchscreen faceplate Before installing faceplate remove the protective film from the LCD area of the touchscreen Fasten the faceplate onto
12. the backbox a Remove the two screws as shown in Figure 3 DO NOT REMOVE THE SCREWS ON THE GREEN CIRCUIT BOARD Retain screws for reassembly b Remove the touchscreen assembly as shown in Figure 3 Figure 3 4 Install the backbox into the cutout in the wall a Insert the communications cable through the rectangular cutout in the touchscreen backbox b Locate the retaining flange screws in the upper right and lower left corners Turn the screws counterclockwise until the gap between the retaining flange and the housing flange is wider then the wall see Figure 4 TOUCHSCREEN BACKBOX TOP VIEW s a Lo Lo I Figure 4 c Place the assembled unit into the cutout in the wall d Turn the retaining flange screws clockwise until they are snug do not over tighten gt i 3 o f A a a 5 jl l J D S ag Z 1A Uy LY the i Wy Li wa L Figure 5 5 Terminate the communications cable a When connecting the touchscreen directly to the HAI controller use the supplied 8 position modular cable assembly Attach the wires coming from the controller to the supplied cable assembly using the supplied wire spice connectors b When connecting the touchscreen to
Download Pdf Manuals
Related Search