Home Automation 62A12-1 User's Manual
Contents
1. Setting the Frequency of the IR Output When using the RIM to send IR data to source equipment there are Eq two different IR carrier frequencies in which the RIM can transmit the IR signal The default setting of 38 kHz is used for most audio sources However most cable and satellite converter boxes operate at a higher IR carrier frequency closer to 56 kHz Each RIM has a jumper that allows you to change the frequency of the IR output FREQUENCY when using such devices MBER To change the frequency setting remove the faceplate and insert from the RIM as described under Changing the Color of the RIM Once The Insert Has Been Removed Move The Frequency Jumper CN1 From The 38khz Position To The 56khz Position Page 2 IR Output Each RIM ships with an IR flasher 62A08 1 The IR flasher is used for sending IR data to the source equipment When you point your source equipment remote control at the IR receiver in the VSC and send a signal the IR data is routed to the appropriate RIM to which the source is connected which then sends the IR signal through the IR flasher to the source equipment IR OUT NX AUDIO IN Hi Fi RIM Remote Input Module RIM IR RECEIVER WINDOW IR FLASHER 4 b Rp SOURCE EQUIPMENT FRONT Installing Volume Source Control VSC Units The audio sources can be selected and controlled by any Volume Source Control VSC Additionally each VSC include an IR receiver that al2. connected directly to Remote Input Modules RIM in rooms that will have music sources Remote Input Modules connect directly to the Hi Fi Main Assembly using Cat 5 unshielded twisted pair UTP for communications Each end of the wire is terminated with an RJ45 connector The correct wiring scheme for the Cat 5 cable is standard EIA TIA 568A Properly terminating the Cat 5 cable is crucial for the operation of the system It is best that no single run of Cat 5 exceeds 500 feet Insert the 145 connector on one end of the cable to the respective source input jack 1 6 under Remote Audio In IR Out on the Hi Fi Main Assembly Insert the RJ45 connector on the other end of the cable to the jack labeled Remote Audio on the RIM Changing the Color of the RIM The color of the RIM may be changed to complement the interior d cor The RIM is supplied with a white faceplate and insert Additional colors are available contact your HAI distributor for more information Change the color of the RIM as follows Page1 1 Remove the faceplate 2 The insert attaches to the RIM with one latch on the right and one on the left Using a small bladed screwdriver gently depress the latch on one side while lifting up on the insert Once the latches are released on one side remove the insert from the other side 3 Align the latches of the new insert to the openings on the RIM and gently snap into place 4 Attach the new faceplate
3. side remove the insert from the other side 3 Align the latches of the new insert to the openings on the RIM and gently snap into place 4 Insert the new knob onto the volume control shaft Attach the new faceplate Setting the Zone Address Although the Hi Fi Main Assemble has separate RJ45 connectors for each zone each VSC must be configured to a specific zone address to establish its location This setting is made on the back of the VSC using a rotary switch To set the zone address place a small screwdriver in the slot on the rotary switch and turn it to the appropriate zone address number 1 8 Model 62A03 1 Volume Source Control Zone Control Page 4 Speaker Wiring When running the cables for speakers use 16 gauge two conductor or four conductor four conductor stranded is recommended for neater installation speaker wire Speaker cable is homerun from the speaker location to the location of the Hi Fi Main Assembly The Hi Fi System is designed to work with one pair of speakers per zone Terminating Speaker Wires Always observe proper orientation of the positive and negative signal for each speaker connection Typically when using two conductor speaker wire the red wire indicates positive and black wire indicates negative Another indication of positive is a dark line running through the insulation Four conductor wire can also be used and makes for a neater installation Four conductor wire
4. 62A12 1 Hi Fi Expansion Kit Installation Manual Music that can live anywhere Easy to operate Enjoy music regardless of where it lives anywhere in the house i e simply push the volume knob O select your living room CD player as a source of rnusic as you relax on your patio and then use your CD remote to control the song selection or volume without getting up rom your lawn chairl High Fidelity performance thatS affordable More power and lexibility than amplified Keypad systems at similar cost First built in unit with remote input module Your music can be located anywhere instead of in an audio rack Wiring to he main unit is hidden for a neat installation Document Number 62112 1 Rev A October 2006 Copyright 2006 Home Automation Inc All Rights Reserved Description This kit expands the HAI Hi Fi Whole Home Audio Distribution System from 4 Zones and 4 Sources to a full 8 Zone 6 Source system Features e Adds an additional 4 zones of audio and 2 audio sources throughout your home e Modular Zone Amplifier Cards plug into the Hi Fi Main Board Assembly e Remote Input Modules RIM and Volume Source Control VSC Units connect using Standard Category 5 Wiring Includes 4 Zone Amplifier Cards 2 Remote Input Modules RIM with 2 IR Flashers 4 Volume and Source Control VSC Units Power Supply that powers 4 zone amplifiers Manual Installing Remote Input Modules RIM All audio sources are
5. Power Rated Distortion 1 2 power Rated Impedance Damping Factor Frequency Response 20 20kHz Preamplifier Section Variable output Impedance Source Inputs 1 6 Input Impedance Input Sensitivity for rated power Input Overload Emitter Outputs Output Drive Current Output Drive Voltage System System On Page Mute input Power Requirements Power Supply Input each Power Supply Output each Power Consumption All channels driven to full rated power Average operating conditions No signal Physical Specifications Unit Size in enclosure Unit Size on mounting plate Unit Weight in enclosure Unit Weight on mounting plate 30W 15W x 2 Two channels driven 30 20kHz 1 THD 0 40 6 Ohms 50 2dB 0 600mV 600 Ohms 10K 300mV RMS 3V RMS 100mA 5V 5V 50mA Ring Ground Normally open close to activate 100 240VAC 50 60Hz 120W 30VDC 3 Amps 240W 30W Less than 10W 13 W x 13 H x 4 5 D 13 25 W x 8 5 H x 3 75 D 14 Ib 8 lb Page 9 Hi Fi by HAL HAI New Orleans LA USA
6. has four separate wires in one outer jacket making it possible to run a single speaker wire for a pair of zone speakers This type of wire typically uses red and black for one speaker and white as positive and green as negative for the second speaker Use 16 gauge speaker wire 4 conductor stranded is suggested for neat installation SPEAKERS SPEAKERS Page 5 Installing Zone Amplifier Cards Zone Amplifier Cards ZAC can be added at any time to increase the total number of zones to eight To install a Zone Amplifier Card X 1 Power down the Hi Fi system by OO CEE unplugging both Power Supply units if applicable from the inputs labeled slale Power on the Hi Fi Main Assemble t5 E 8 2 fe 8 8 HiFi uS E D www homeauto com 2 Pull upward on each of the 4 plungers wl until you hear them snap ON 3 Remove the cover from the Hi Fi Main Assembly by lifting it away from the Hi Fi circuit board Page 6 4 Install additional Zone Amplifier Cards in an empty connector CN5 CN8 by positioning the Zone Amplifier Card directly over the connector and gently but firmly pushing down on both sides of the card until the top and bottom are securely seated into the connector 5 Replace the cover by pushing down on each of the 4 plungers until you hear them snap 6 Reconnect each Power Suppl
7. lows you to remotely control the Hi Fi system and or audio sources from any zone in the house Volume Source Control VSC Units connect directly to the Hi Fi Main Assembly using Cat 5 unshielded twisted pair UTP for communications Each end of the wire is terminated with an RJ45 connector The correct wiring scheme for the Cat 5 cable is standard EIA TIA 568A Properly terminating the Cat 5 cable is crucial for the operation of the system The total distance of Cat 5 between the Hi Fi Main Assembly and the VSC units must not exceed 2000 feet It is best that no single run of Cat 5 exceeds 250 feet Insert the 145 connector on one end of the cable to zone input jack 1 8 under Zone Control IR In on the Hi Fi Main Assembly Insert the 145 connector on the other end of the cable to the jack labeled Zone Control on the VSC Page 3 Changing the Color of the VSC The color of the VSC may be changed to complement the interior d cor The VSC is supplied with a white faceplate knob and insert Additional colors are available contact your HAI distributor for more information Change the color of the RIM as follows 1 Remove the faceplate Firmly grasp the knob and pull straight outward until the knob is removed 2 The insert attaches to the VSC with one latch on the right and one on the left Using a small bladed screwdriver gently depress the latch on one side while lifting up on the insert Once the latches are released on one
8. y Page 7 Powering the Hi Fi System The Power Supply HAI Part Number 62A07 1 powers the Hi Fi processor and 4 Zone Amplifier Cards One Power Supply is needed to power Zones 1 4 and a second Power Supply supplied is used to power Zones 5 8 when connected to the Power jack on the right 1 Insert the connector for the Power Supply into the Power jack marked PJ1 jack to the left under the section labeled Power Zones 1 4 on the Hi Fi Main Assembly 2 Plug the power cord from the Power Supply into a 120 VAC outlet The POWER ON LED will illuminate The Hi Fi system will start Follow the instructions in the User s Guide for operation 3 Insert the connector for the Power Supply into the Power jack marked PJ2 jack to the right under the section labeled Power Zones 5 8 on the Hi Fi Main Assembly Plug the power cord from the Power Supply into a 120 VAC outlet The POWER ON LED will illuminate Zones 1 4 Zones 5 8 One 62A07 1 Power Supply is used to power Zones 1 4 A second 62A07 1 Power Supply is used to power Zones 5 8 POWER SUPPLY HAI Part Number 62A07 1 Universal Power Supply for Hi Fi For Zones 1 4 Supplied with 4 Zone 4 Source Kit x POWER SUPPLY HAI Part Number 62A07 1 Universal Power Supply for Hi Fi For Zones 5 8 Supplied with Hi Fi Expansion Kit Page 8 Specifications Zones 1 8 Power Amplifier Outputs Continuous Average Output
Download Pdf Manuals
Related Search