Home Automation 38A00-3 User's Manual
Contents
1. Na HAI UPB Lumina Mode Controller MAI Installation and Operating Instructions For the following Model 38A00 3 HAI UPB Lumina Mode Controller READ THESE INSTRUCTIONS BEFORE INSTALLING DEVICE This HAI UPB Lumina Mode Controller is intended for installation in accordance with the National Electrical Code and local regulations It is recommended that a qualified electrician perform this installation Retain these instructions for reference This product is for indoor use only Connect only copper or copper clad wire to this device Important Notes Prior To Installation Be sure that all power to the load has been disconnected by turning off the circuit breaker Installing an HAI UPB Lumina Mode Controller with power on may expose you to dangerous voltage and may damage the device HAI UPB Lumina Mode Controller Overview The HAI UPB Lumina Mode Controller Figure 1 is used to easily change the mode before leaving your house going to bed arriving home going on vacation entertaining for the evening or any other special event It uses the UPB two way powerline communication technology to communicate with a Lumina controller to initiate programs for preset lights and temperatures The HAI UPB Lumina Mode Controller has six pushbuttons labeled AWAY HOME SLEEP VAC Vacation SPCL Special and PARTY Each pushbutton is slightly backlit so that the buttons can be seen in a dark room The pushbuttons of the curr2. pushbuttons simultaneously for at least 3 seconds 4 The LED indicators will stop blinking and the SLEEP and PARTY pushbuttons will illuminate to indicate that it has been reset SPECIFICATIONS Model Number 38A 00 3 Number of Backlit Pushbuttons with LED Indicators 6 Connections 18 GA Dimensions 4 1x1 7x 1 5 Weight 0 25 lb Mounting Standard J Box Input Power 120 12 VAC Input Frequency 60 3 Hz Operating Temperature 40 F to 104 F Note It is normal for this switch to make a slight buzzing sound during operation LIMITED WARRANTY HAI warrants this product against defects in material and workmanship under normal use and service for a period of two 2 years from the date of purchase During the warranty period HAI will repair or replace at its sole option if this product fails due to defect This warranty does not cover the cost of removal or reinstallation of any product This warranty does not cover failure caused by normal wear damage to the product while in your possession other than damage caused by defect or malfunction or by its improper installation including failure to follow the written installation and operation instructions alterations misuse or abuse The remedies provided for in this warranty are the sole and exclusive remedies thereof In no event shall HAI be liable for incidental expenses or consequential loss or damages For the complete HAI Warranty for USA policy see the HAI web site at www ho
3. To configure the HAI UPB Lumina Mode Controller using a Lumina keypad it must be put into Setup Mode as follows Step Operation 1 Press and hold the AWAY and HOME pushbuttons simultaneously for at least 3 seconds 2 All of the LED indicators will blink to indicate that the HAI UPB Lumina Mode Controller is in Setup Mode Configuring the HAI UPB Lumina Mode Controller from a Lumina Keypad HAI UPB Lumina Mode Controllers reside on the 8th unit in any Room Configure the HAI UPB Lumina Mode Controller on the 8th unit in a Room as follows Step Operation 1 Put the HAI UPB Lumina Mode Controller into Setup Mode as described above 2 On the Lumina keypad from the main menu or top level display press 6 STATUS and then press 1 CTRL 3 Enter the Unit Number of the HAI UPB Lumina Mode Controller followed by the key and then press 4 The display will provide you with step by step configuration status When complete the display shows COMPLETED Reset to Factory Default Settings To reset the HAI UPB Lumina Mode Controller to factory default settings Step Operation 1 Press and hold the AWAY and HOME pushbuttons simultaneously for at least 3 seconds 2 All of the LED indicators will blink to indicate that the HAI UPB Lumina Mode Controller is in Setup Mode 3 Press and hold the SLEEP and PARTY
4. configuration the HOME pushbutton will fade the UPB Wall Switch Dimmers to 0 off at each switch s default fade rate when pressed When the HOME pushbutton is double tapped the UPB Wall Switch Dimmers will snap to 0 When pressed or double tapped the HOME pushbutton will illuminate and any others are turned off The HOME pushbutton is also used to dim the last lighting scene that was turned on When the HOME pushbutton is pressed and held down the UPB Wall Switch Dimmers will slowly dim and then stop dimming when the HOME button is released In its factory default configuration the SLEEP pushbutton will brighten the UPB Wall Switch Dimmers to 80 at each switch s default fade rate when pressed or double tapped When pressed the SLEEP pushbutton will illuminate and any others are turned off In its factory default configuration the VAC pushbutton will brighten the UPB Wall Switch Dimmers to 60 at each switch s default fade rate when pressed or double tapped When pressed the VAC pushbutton will illuminate and any others are turned off In its factory default configuration the SPCL pushbutton will brighten the UPB Wall Switch Dimmers to 40 at each switch s default fade rate when pressed or double tapped When pressed the SPCL pushbutton will illuminate and any others are turned off In its factory default configuration the PARTY pushbutto
5. TRUCTIONS 1 Be sure that all power at the wall box has been disconnected by turning off the circuit breaker 2 If applicable remove the faceplate from the existing device remove the existing device from the wall box and disconnect the wires from the existing device Identify the Line black and Neutral white wires 3 Remove 4 of insulation from each of the wires on the HAI UPB Lumina Mode Controller Install the HAI UPB Lumina Mode Controller by connecting wires per wiring configuration shown in Figure 3 4 After all connections have been made be certain that all wire connectors are firmly attached and there is no exposed copper 5 Gently place the wires and HAI UPB Lumina Mode Controller into the wall box with the AWAY pushbutton at the top of device Using the supplied screws attach the HAI UPB Lumina Mode Controller to the wall box 6 Before installing the faceplate restore power to the circuit for testing 7 After testing the HAI UPB Lumina Mode Controller for proper local operation install a Decora style faceplate over the HAI UPB Lumina Mode Controller MAIN 38A00 3 CIRCUIT 5 lt LUMINA BREAKER MODE PANEL CONTROLLER BLACK WHITE NEUTRAL 120VAC a 60Hz i LINE Figure 3 Wiring Diagram HAI UPB LUMINA MODE CONTROLLER OPERATION Although the HAI UPB Lumina Mode Controller will perform differently once it is configured by the Lumina controller the followin
6. ent Lumina Mode will be distinctly illuminated so that you can always tell which mode you are currently in just by glancing at the Lumina Mode Controller To change the current mode from a Lumina Mode Controller simply press the desired mode button The new mode button will illuminate and the lighting and temperatures in your home will be changed accordingly AWAY Vi S SLEEP N ee VAC SPCL A A PARTY AS la HOME Figure 1 HAI UPB Lumina Mode Controller 38100 3 Rev B Changing Switch Color The color of the HAI UPB Lumina Mode Controller may be changed to complement the interior d cor The HAI UPB Lumina Mode Controller is supplied with a white bezel Additional colors are available contact your HAI distributor for more information When changing the bezel make sure that the HAI UPB Lumina Mode Controller is disconnected from all power and proceed as follows 1 The bezel attaches to the HAI UPB Lumina Mode Controller with two small Philips head screws one on the upper right corner and one on the lower left corner Figure 2 2 Using a small bladed Philips screwdriver unscrew each of the two screws Remove the bezel from the back housing 3 Install the new bezel by aligning the mounting holes on the bezel with the installation pins on the back housing Secure bezel to back housing with the two ae Phillips screws that were removed in Step 1 Figure 2 Changing Switch Color INSTALLATION INS
7. g describes the operation of the HAI UPB Lumina Mode Controller in its factory default configuration The HAI UPB Lumina Mode Controller has six pushbuttons labeled AWAY HOME SLEEP VAC SPCL and PARTY which by factory default are used to control six lighting scenes When the pushbutton labeled AWAY is pressed the LED behind the AWAY pushbutton is illuminated and any other is turned off When the pushbutton labeled HOME is pressed the LED behind the HOME pushbutton is illuminated and any other is turned off When one of the pushbuttons labeled SLEEP VAC SPCL or PARTY is pressed the LED behind the respective pushbutton is illuminated and any other is turned off No more than one pushbutton is illuminated at a time Pushbutton Operation In its factory default configuration the AWAY pushbutton will brighten the UPB Wall Switch Dimmers to 100 at each switch s default fade rate when pressed When the AWAY pushbutton is double tapped the UPB Wall Switch Dimmers will snap to 100 When pressed or double tapped the AWAY pushbutton will illuminate and any others are turned off The AWAY pushbutton is also used to brighten the last lighting scene that was turned on When the AWAY pushbutton is pressed and held down the UPB Wall Switch Dimmers will slowly brighten and then stop brightening when the AWAY pushbutton is released In its factory default
8. meauto com Any implied warranties including warranties of merchantability and fitness for particular use or purpose are limited to a period of two 2 years from purchase date This warranty gives you specific legal rights and you may have other legal rights which vary from state to state Some limitations may not apply to you For warranty and repair service within the continental United States send defective unit carefully packaged postage prepaid along with description of trouble name return address and phone number to HAI Repair Department 4330 Michoud Blvd New Orleans LA 70129 HAI will pay return shipping charges via normal ground service Outside of the continental United States Contact an Authorized Distributor for repair replacement instructions c US LISTED
9. n will brighten the UPB Wall Switch Dimmers to 20 at each switch s default fade rate when pressed or double tapped When pressed the PARTY pushbutton will illuminate and any others are turned off CONFIGURING THE HAI UPB LUMINA MODE CONTROLLER The HAI UPB Lumina Mode Controller is designed to set the mode in a Lumina system but also has several configuration options Option Factory Default CONFIGURED AS LUMINA MODE CONTROLLER AWAY Pushbutton On Button Link 001 Sets the Lumina mode to Away HOME Pushbutton Off Button Link 002 Sets the Lumina mode to Home SLEEP VAC SPCL Scene Activator Links 003 Sets the Lumina mode to Sleep Vacation Special and Party and PARTY Pushbutton 004 005 006 respectively respectively AWAY HOME SLEEP Each LED Indicator is assigned When the Lumina mode is changed the LED indicator behind VAC SPCL and to its pushbutton s Link ID the respective pushbutton is illuminated and any other is turned PARTY LED Indicators off Each LED Indicator is mutually exclusive only one LED is on at a time UPB Transmission Attempts 2 No change UPB ID NID 255 The Lumina controller configures Network ID NID Unit ID UID 080 UID Network Password Network Name Room Name Device Name etc LED Brightness High No change LED Backlighting Enabled No change Setup Mode
Download Pdf Manuals
Related Search