Hobart SLA-2 ML-44180 User's Manual
Contents
1. abels are not advancing When the sensor does not find a label edge in 5 seconds the message Out of Security Labels displays on the Ultima console and a beep sounds to alert the operator If used with an HSW or NSW Semi Automatic System the security label is automatically placed on the scale label but the Operator must hand apply the labels to the package Page 7 of 12 F33995 Rev A 6 06 Loading Labels F33995 Rev A 6 06 The SLA contains a label sensor to alert the operator when out of labels or when labels are not advancing When applicable the message Out of Security Labels displays on the Ultima console and a beep sounds to alert the operator Although when out of security labels the Ultima merchandising labels continue to print You may also receive this message if the SLA is turned off but you are still operating the Ultima printer Refer to the following procedures and diagrams to correctly load labels Be sure the SLA is powered off when loading labels If applicable remove the backing paper from the take up spool and label core from the label hub before you begin loading To load labels 1 Open the SLA label supply door 2 Turn off power at ON OFF power switch 3 Place the roll of labels on the label hub 4 If the label roll does not have a leader strip approximately 12 of labels off the backing paper to create a leader 5 Thread the leader between the label sensor guide and the label guide a2. el Applier ILA As a label is printed and expelled from the Ultima Printer the SLA attaches a security label to the adhesive side of the merchandising label The UWS CLA or ILA then places the label on the package As the label s barcode is scanned the security label is deactivated by the security provider s Checkpoint or Sensormatic equipment and will not be detected by the store security system a 1 Dwell arm 6 Peel bar 2 Tension arm 7 Take up spool 3 Label hub 8 Power on indicator 4 Label eject switch 9 ON OFF power switch 9 Label sensor assembly Page 3 of 12 F 33995 Rev A 6 06 Note If used with an HWS or NSW Semi Automatic System the security label is automatically placed on the Ultima scale label The Operator then hand applies the labels to the package There are two types of security labels available Depending on your store security system you will either use the Checkpoint label similar in size to the safe handling label or the Sensormatic label similar to what is used with audio CDs CHECKPOINT LABEL SAMPLE ae SENSORMATIC LABEL SAMPLE 16368 Note For label ordering information contact your security system provider Power runs to the SLA through a standard 110 VAC electrical Powering Up Powering connection Flip the switch located inside the unit or lower front Down to power up down The SLA can determine which packag
3. es receive a security label Setting Up the SLA by Minimum Unit Price Minimum Total Price and or PLU number Note Early model SLA was only configurable for minimum Unit Price F33995 Rev A 6 06 Page 4 of 12 HOBART 2006 1 At the Ultima Keypad PRESS SUPER MENU ON OFF If applicable enter your Secret ID The Supervisor Menu displays 2 PRESS F5 to select Scale Setup Menu Change product Memory free 1971 K Totals Menu Print repovts menu Eackup or Restore menu Scale setup menu Miscellaneous menu or enter the function code Return to Operate mode 16365 3 PRESS F3 to select Labels Menu Select special fields to print on a label Label text names Label information Label types Security labels HOBART 2006 Page 5 of 12 F33995 Rev A 6 06 5 From the Security Labels screen enter the minimum Unit Price and or the minimum Total Price A security label will be applied to any package with a Unit Price and or Total Price that is the same as or higher than the amounts entered If the Unit Price and Total Price are lower than the entered prices the security label will not be applied Security labels Enter the minimum Unit Price to apply a Security label Enter the minimum Total Price to apply a Security label 6 PRESS ESC to return to the Start a Run screen To set up the SLA to apply a label by PLU 1 Atthe Ultima Keypad PRESS SUPER MENU ON OFF If applicable enter your Secre
4. l Hobart Office Power ON indicator is illuminated and will not 1 Call local Hobart Office issue label motor does not run Issue label only when manual eject button is 1 Minimum Unit Price or minimum Total pressed Price is set too high in the Security label setup and or apply by PLU is not configured correctly in Change Product screen in Supervisor 2 Call local Hobart office Label does not peel off of backing paper 1 Verify labels threaded correctly Call local Hobart office F 33995 Rev A 6 06 Page 10 of 12 HOBART 2006 SYMPTOMS POSSIBLE CAUSES REMIDIES Multiple labels are issued followed by an 1 Verify labels threaded correctly audible beeping sound 2 Call local Hobart office No label is issued followed by an audible 1 Out of security labels beeping sound 2 Missing security labels on backing paper 3 Verify labels threaded correctly 4 Call local Hobart Office Security label placement on Ultima label is incorrect Verify that dwell control lever is resting against the backing paper on the take up spool Verify labels threaded correctly Call local Hobart office HOBART 2006 Page 11 of 12 F33995 Rev A 6 06 HOBART 2006 F33995 Rev A 6 06
5. n Arm Label Side Label Sensor Guide Label Label Eject Eject Switch Switch Guide Guide Pins Pins er Label Guide Spool Pin Take up Spool Stripper Plate Te Stripper Guide Plate SLA WITH CHECKPOINT LABELS 16372 SLA WITH SENSORMATIC LABELS 16428 Fig 3 Fig 4 HOBART 2006 Page 9 of 12 F33995 Rev A 6 06 Maintain the SLA by regularly cleaning the paper dust from Cleaning and inside the unit Clean the SLA exterior surfaces with a cloth and Maintaining warm water detergent solution When cleaning be sure to protect the unit from direct water entry To clean the SLA 1 Dampen a soft cloth with mild detergent and water 2 Wipe the exterior surfaces Remove any adhered labels with an alcohol soaked cloth Do not use metal to scrape the labels or adhesive off of the unit Troubleshooting DISPLAY PROMPTS POSSIBLE CAUSES REMIDIES i Out of security labels Load security Out of Security labels labels or press escape to continue 2 Verify labels threaded correctly The Security label applier is either oat of sac ite labels 3 SLA power switch is OFF or it is turned off 4 Check power cord and power source 5 Call local Hobart Office Press ESCAPE to clear this message 16371 SYMPTOMS POSSIBLE CAUSES REMIDIES Power ON indicator is not illuminated and unit will 1 SLA power switch is OFF not function 2 Check power cord and power source 3 Call loca
6. s shown in Fig 1 and 2 On the early model SLA thread the leader between the label sensor guide and the 2 guide pins as shown in Fig 3 and 4 6 Continue threading the leader past the label guide pin as shown in Fig 1 4 7 For Sensormatic labels the leader should be threaded between the stripper plate and the stripper guide plate Loop the end of the leader and thread through the slit in the stripper plate as shown in Fig 2 or Fig 4 For Checkpoint labels the leader should be threaded around the stripper plate as shown in Fig 1 or Fig 3 8 Thread the leader thru the slots of the take up spool Wrap the leader counterclockwise around the take up spool as shown in Fig 1 4 9 Turn the take up spool counterclockwise a few times to be sure the backing paper winds securely 10 Turn on power at ON OFF power switch 11 Press label eject switch to position the label so that it is visible below the edge of the stripper plate This may require the label eject switch to be pressed several times 12 Close the SLA label supply door Page 8 of 12 HOBART 2006 Label Hub Tension Bar Label ide Tension Arm Label Label Sensor Guide Label Eject Switch Label Sensor Label Eject Switch Label Guide Take up Pin Spool Stripper Plate Stripper Guide Plate SLA WITH CHECKPOINT LABELS 16426 SLA WITH SENORMATIC LABELS 16427 Fig 1 Fig 2 apie Hb Tension Arm Label Side Tensio
7. security Label Applier Operator Manual Model SLA 1 SLA 2 ML 44180 SLA 2A ML 44197 SLA 3 ML 44192 701 S RIDGE AVENUE TROY OHIO 45374 937 332 3000 www hobartcorp com HOBART 2006 F33995 Rev A 6 06 Security Label Applier SLA SAVE THESE INSTRUCTIONS Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CAUTION Look At This To provide continued protection against risk of electric shock connect to properly grounded outlets only F33995 Rev A 6 06 Page 2 of 12 HOBART 2006 Security Label Applier HOBART 2006 The Security Label Applier SLA is designed to apply an Electronic Article Surveillance EAS label to a standard Ultima scale label The SLA works in conjunction with an Ultima with remote keypad and an Ultima Wrapping System UWS Compact Label Applier CLA or Indexing Lab
8. t ID The Supervisor Menu displays 2 Use the numeric keypad to enter 10 in the Function code box and PRESS ENTER Change product Memory free 1971 K Totals Menu Print repovts menu Backup or Restore menu Scale setup menu Miscellaneous menu or enter the function code Return to Operate mode 16365 F33995 Rev A 6 06 Page 6 of 12 HOBART 2006 Operating the SLA HOBART 2006 3 Use the numeric keypad to enter PLU number in the Product number and PRESS ENTER Pglof 4 hande another Broduc Bo sat ages Seoarity fabe Bore this grodu f EhuBpt 0 set type Change another field Z Change text tioii Next para 16360 4 PRESS F2 to select Apply Security Label Palof 1 Change another product Apply Security label Delete this product Seks Gansant type Change product Product number Description UPC number system UPC By count Unit price Percent off Tare Shelf life Product life Change product Product number Description SANDWICH UPC number system UPC Change another field By count Unit price Percent off Fe hange texi ia 16363 5 PRESS ESC to return to the Start a Run screen Tare Shelf life Product life Once set up the SLA runs with minimal operator intervention The labels are automatically generated combined and placed on the appropriate package The SLA contains a label sensor to alert the operator when out of labels or when l
Download Pdf Manuals
Related Search