Home

Hi-Touch Imaging Technologies Mug Heat Press Kit User's Manual

image

Contents

1. adjustor to tight on the mug against the plastic roller With hand holding the mug holder rotate the mug counter clockwise and clockwise to squeeze any air between the mug and the photo Useful Tips 1 Start to bubble elimination process immediately after pre heating process in order to have the best result 2 Start from the center of the photography to eliminate the bubble Rotate clockwise and counter clockwise 5 times 3 Please wear a pair of glove to avoid burning 15 Hold on the mug holder and release the adjustor Remove the mug from the Bubble Eliminator 16 Place the mug in Mug Heat Press wrapper Hold on the mug holder and tighten the space between mug and the wrapper Press OK button to continue the heating process again Useful Tips 1 Due to silicon is been heating and it will increase the pressure to hold down the lever Please lose the lever knot to release the pressure 2 Press and hold down the lever to ensure the imprint quality 17 When heating process is completed machine automatically stops Press OK button to stop the alert tones hold on the mug holder and take out the mug from wrapper with extreme care CAUTION DO NOT TOUCH THE SURFACE OF MUG IT IS EXTREMELY HOT gt 18 Wait until the temperature of mug cools down then remove the mug locating tape Useful Tips 1 Peel the photo off immediately while heating completed can get ultimate output 2 Avoid burnin
2. appears during air pocket removing 8 Use mug locating tape to secure another side of the photo onto the mug s surface 9 Hold on the mug holder and release the adjustor Remove the mug from the Bubble Eliminator 10 Place the mug in Mug Heat Press wrapper Hold on the mug holder and tighten the space between mug and the wrapper WARNING Avoid the contact between plastic cover and mug handle ATTENTION Do not place the mug upside down 11 Flip down the plastic cover 12 Select lt RUN gt and press OK an the default setting would be applied for the heating process the default pre heating time temperature is 1 min 130 C and the default heating time temperature is 4 min 150 C You can also select Setting to adjust pre heating time pre heating temperature heating time heating temperature Then press Start to begin Set pre heating temperature Set heating temperature Set pre heating time E Set heating time Hl a 2 LE 13 When pre heating process is completed machine automatically stops Press OK button to stop the alert tones release the holder and proceed to Bubble Eliminator process Useful Tips 1 If smokes comes out from Mug Heat Press machine during the pre heating phase this is caused by the water in the silicon is evaporating 2 A Da Da will sound on machine if temperate reaches pre heating temperature of 1309C 14 Push the
3. void authority to use this equipment FEDERAL COMMUNICATIONS COMMISSION Declaration of Conformity DoC T s f llowing equipment Trade Masse HITI S T ModeMumber i JIEN n U i herewith conflemed to comply with tht requirements of FOC Part 15 Rules The operatian is subject to the Following tien conditions 1 This device many acd come barmit interference ace 1 Ti device must accept asy inierfesesec received including interference that may cane andere aperamon t 1 3 i g i 1 i f 4 i The reaulr a electromagnetic emission hes been evaluaced by ETC EMI Laboratory NV LAP LAS CODE 7001 334 and showed im the test H ii uzderstood that each urdt marketed zi identical 5o the device os iesind mi kay Changes bo the device whioh could adyessety affect the cussion chansc berisreca will eequire neat The following unparter eranufarturer d gessonsibls for this deciernilon Company Kame _ He Touch Imaging Technologies America inc Company Address 945 5 Greenwood Avg STE J Mantebella CA 90640 USA i i l i i L i 4 i i 4 Telephone UIT 323 788 9900 rime OETA L T 4 i i 5 i i L i 3 i DATS eS uL T EAdARAETGx umyrcoHkbkb qu Ree ete FCC Doc Label EF F A F gw IE ee T CPU Board amp Power Supply f 4e F Model Number Tested T
4. Hi Ti Photo Printer Mug Heat Press Kit User Manual ACKNOWLEDGEMENTS Microsoft MS MS DOS and Windows are registered trademarks of Microsoft Corporations Pentium is a U S registered trademark of Intel Corporation TrueType is a U S trademark of Apple Computer Inc Adobe and Acrobat a registered trademarks of Adobe Systems Incorporated Brands and product names are trademarks or registered trademarks of their respective companies COPYRIGHT The information contained in this document is subject to change without notice Hi Touch Imaging Technologies makes no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose Hi Touch Imaging Technologies shall not be liable for any errors or for incidental or consequential damages in connection with the furnishing performance or use of this material Reproduction adaptation or translation of this manual is prohibited without prior written permission of Hi Touch Imaging Technologies except as allowed under the copyright laws Hi Touch Imaging Technologies Hili HiTi company logo PhotoDesiree Digital mini lab just for you HiTi name written in Simplified Chinese or Traditional Chinese are trademarks or registered trademarks in Taiwan China and other countries of Hi Touch Imaging Technologies SAFETY INSTRUCTIONS 1 Read these instructions carefully Save these inst
5. an be display when the image is imprinted onto the ceramic mug The four effects are Normal Landscape Portrait and Artistic Portrait this will enhance the imprinted people image on the mug Landscape this will increase the color saturation imprinted on the Artistic this will double the color saturation imprinted on the mug Artisitc effect is good if image is text or logo Normal the imprinted image on the mug is the same as the original image The effect wasn t directly apply on the screen you could see the effect after the Mug was finished SAVE MM 16 Use Ed you can save the result of this editing 17 Page color setting and Print Increase or decrease the gamma of the image to achieve the optimal color balance when image is transferred onto the ceramic mug Print out the image Chapter 3 Mug Heat Press Standard Operation Procedure 1 You should have the following tools in hand Mug Heat Press Bubble Eliminator White Ceramic Mug Mug Locating Tape Dye Sublimation Photograph Mug Locating Coil Clean Towel recommend polyester fabric a pair of gloves and a bottle of methane 2 Pour an equivalent of 1 teaspoon of methane into the polyester fabric Carefully wipe the surface and remove any dirt or dust from the white ceramic mug Useful Tips 1 Use only the photograph that is just been printed out for mug imprint 2 Gently remove any dust from photograph a
6. ccording to the following procedure 1 lake out the cracked Teflon 2 Use new Teflon and fold the two sides along the folding lines The folding lines should be vertical to each other as the following illustration Two mark for both side 3 Put the Teflon inside the mug heat press as illustrated below Put it onto the Mug Heat Press 4 Wrap up the U part on both sides of the white Teflon to cover the white slicon the orange heater plate and the black rubber as illustrated below Cover the white orange and black components Chapter 5 Useful tips for Mug Heat Machine Maintenance Erros Message displays on Action Taken LCD COVER OPEN Flip down the plastic cover and press OK OVER HEAT Press OK and turn off the power first and then turn it back on 1 Turn off the power first and then turn it back on 2 Check if the connection is loose between heating pad and wire 3 Replace the heating pad if above steps fail to solve the problem Press OK and turn off the power first and then turn it back on If you are still unable to make the machine function properly please contact local distributor or regional HiTi offices Taiwan lesd hi ti com 886 2 8258 3060 Mainland China csd Qhi ti com 86 512 6760 1688 Europe jalesQhiti nl 31073 6450897 USA ewiceQhitouchimaging com 1 323 728 9900 Others csdQhiti com 886 2 8258 3060
7. g from touching please wear glove 3 Avoid double image don t stick the photo on the mug again 4 4 A photo only can transfer one Mug 19 The whole heating process is completed You can stop or start from the beginning and repeat the whole procedure to create a new personalized mug Note omokes may come out from the Mug Heat Press during the heating process The phenomenon is normal due to the water is been evaporating during the heating process Chapter 4 Consumable Replacement 4 1 Heater Plate Replacement 1 Turn off the power and wait for 20 minutes for machine to cool down 3 Pull the heater plate from machine you will see a semi sphere hole where a wire is connecting with heater plate Semi sphere hole 5 Make sure the wire and the new heater plate is properly reconnected 6 Put the connector through the semi sphere hole and put the heater plate into the original location Then put the black rubber and white Teflon onto the machine Make sure the heater plate black rubber and white silicon are wrapped by white Teflon Then push the white Teflon into the original location 110V and 120V Blue line 220V and 220V White line 4 2 Teflon Replacement The white Teflon on the surface of the heater plate is used for improving the image transferring effect onto the mug If you find any cracks on the surface of the Teflon please contact your local distributor and replace the Teflon a
8. nd ceramic mug 3 Use methane to clean the surface to avoid any dust been left out 4 4 Avoid direct finger contact with mug and photograph surface 3 Place the white ceramic mug into the mug locating coil Align the mug holder with the mug locating coil as illustrated below The zero of locating coil Useful Tips 1 Carefully cutting off excessive margin on top of photography 2 Place mug inside locating coil The bottom of the mug should be in parallel with locating coil 3 Left and right side of photograph should be in parallel with the edge of locating coil 4 4 Avoid any gap between mug and photography 4 Wrap the Dye Sublimation Photography on the mug with the image facing the mug and the bottom of photography is just above the mug locating coil Useful Tips 1 Remain the opposite position between photo and Mug surface before sticking the tape 2 Remove locating coil after photograph is firmly taped on mug 6 Place the mug up side down on the Bubble Eliminator with the mug holder facing outward 7 Push the adjustor to tighten the mug aginst the plastic roller With hand holding the mug holder rotating the mug counter clockwise to squeeze any air between the mug and the photo Useful Tips 1 Ensure no gap between photography and mug while using bubble eliminator to squeeze out air pocket 2 Tape the mug when bubble eliminator 3 Use finger to press the wrinkle while wrinkle
9. nsor and plastic cover design secure and accurate for useAutomatic power off design while abnormal activities appearBundled software MugDesiree to provide solution for Mug personalization d np bran e Ook l p MugD sir e Ca Chapter 2 MugDesiree Introduction 2 1 Mug Desiree Installation MugD iree i shift Histo ll es ng Techologies To Install 1 Insert MugDesiree CD into CD ROM 2 If CD ROM does not auto start please click Start Run and type D SETUP EXE where D is your CD ROM drive 3 Click OK Follow the instructions on the screen b Imaging E E 3 To start 1 Click Start Programs Go to the HiTi folder select the MugDesiree folder and click MugDesiree EE Professional j 2 2 Operation Procedure 1 Select Start Programes HiTi HiTi HitiMug MugDesiree or double click T to run MugDesiree 2 Press S button and import the images from computer 3 Press button and import images from HiTi printer 4 Press A button and import templates from computer You can edit the template format such as rotate color setting as the step 10 14 5 Press button and switch the file browser mode and templates browser mode 6 MugDesiree will automatically adjust any poor quality images if you set a n mark in i 7 You can select HiTi default setting Hi Ti provides three kind of lay
10. o Comply With FOC Standards Trade Mame Model Humber Assembled ram Tested Components Carp parem bing Tope FOR HOME OR OFFICE USE FOR HOME OR OFFICE USE CE Declaration of Conformity of the Leva of the Member Sti relating to EN 55022 1998 Class B TEC 61000 4 3 1996 A1 1998 A2 2000 EN 1000 3 2 1993 A 1 A2 1998 A14 2000 EC 61000 4 4 1995 A2 2000 EN 61000 3 1 1995 A1 1998 IEC 61000 4 5 1995 42 2000 EN 55024 1998 IBC 61000 4 6 1996 A2 2000 IA TEC 61000 4 8 1993 A1 2000 TEC 61000 4 11 1994 A2 2000 a is responsible for this declaration Hi Touch Imaging Technologies KSushom Co Ltd 5 Company Name Mamefaccurer Na 18 QuaXing Rol Crue Sothen Indortrial Park Sazhura 215006 F R China Ab Yas Legal Signature Chapter 1 Welcome 1 1 Our Invitation to HiTi Photo Printer Family It is our pleasure to have you onboard as the member of HiTi Photo Printer family We thank you for your patronage and hope this is just the beginning of our long term ssociation Through our printer picture will be transformed into masterpieces HiTi Photo Printer offers tremendous creativity digital age will become full of wonderful memories and treasures e CI cover design Sec e Patented design Bubble Eliminator to eliminate all potential air pockets while heating 2 2 Other Features e Professional Locating coil design accurate for locating Dual temperature se
11. out as in illustration a b c L al 99mm x 74mm bf 120mm x 74mm cO 51 5mm x 74mm Wis PE a ape sss mm E d cda Mi munem a r3 ms s oe Lucil C negian Hamr New neue Page Intonation Page Name ni rl Paper Type anise CO Peeirail 8 After picking desire print layout press image templates into designated picturing area 9 The edit area is composed of three different layers image template and text layer which could be edited separately You could switch to different layers by use V EA Image layer E Template layer button to import the andes buttons to adjust the size of the image gene within picturing area Fits the image template vertically to the height Fits the image template horizontally to the width the mage Fits the image template horizontally to the width HORAM to the width 11 Use andl buttons to adjust the color effect Change the color by increasing or decreasing the color balance or brightness of the entire photo Increase or decrease the sharpness of the entire photo 12 Use button for text editing screen which allows you to input and adjust text Timer Slew Homan r B ry r rT rfl tbe a F a m ET x T 4m P 13 Use to adjust the location of the image 14 Use NE button for image rotation 15 MugDesiree also provides the four different effects that c
12. risks Refer all servicing to qualified service personnel FCC INFORMATION The Federal communication Commission Radio Frequency Interference statement includes the following paragraph This equipment has been tested and found to comply with the limits for a Class B Digital Device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates use and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communication However there is no guarantee that interference will not occur in a particular installation If these equipment doses cause harmful interference to radio or television reception which can be determined by interference by on or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Never push objects of any kind into these products through cabinet Openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product 4 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 5 The users should not modify or change this equipment without written approval from this company Modification could
13. ructions for future reference Follow all warnings and instructions marked on the product 2 Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 3 Do not use this product near water 4 Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product 5 Openings in the cabinet and the bottom are provided for ventilation to ensure reliable operation of the product and to protect it form overheating these openings must not be blocked or covered Placing the product on a bed sofa rug or other similar surface should never block the openings Theirs products should never be placed near or over a radiator or heat register or in a built in installation unless proper ventilation is provided 6 This product should be operated from the type of power indicated on the marking label If you are not sure of the type of power available consult your dealer or local power company 7 f an extension cord is used with this product make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating Also make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating 8 Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage points or other

Download Pdf Manuals

image

Related Search

Related Contents

スマートデバイス活用ネットワークソリューション - 日本電気        user manual - FuturaShop  Airstream 396 Automobile User Manual  User Manual  Venom SX Booklet.indd  Logiciel NorthEast Monitoring, Inc. Holter LX Analysis Mode d  Samsung HT-TP1200HHHH User Manual  

Copyright © All rights reserved.
Failed to retrieve file