Heath Zenith SL-4180/84 User's Manual
Contents
1. Dual Brite Motion Sensing Coach Light Models SL 4180 84 A Features e Light comes on when motion is detected e Automatically turns light off e Dusk Accent lighting e Photocell keeps the light off during day light hours This package includes Mounting screws and wire connectors A Tail Assembly p Candelabra Lantern amp Coach Requirements e The Light Control requires 120 volts AC e If you want to use Manual Override the control must be wired through a switch e Some codes require installation by a qualified electrician Questions Call 1 800 858 8501 8 00 AM to 4 45 PM Eastern Time weekdays Lo sentimos pero no podemos contestar preguntas en espa ol por tel fono Heath Company OPERATION Works Day Night On Time 5 Sec 1 5 or 10 Min To Dawn 3 6 Hr to Dawn Test Auto Manual Accent resets to Auto Mode at dawn For TEST Set the ON TIME switch onthe bottom of the cover plate to TEST TEST 1 5 10 MIN For AUTO Set ON TIME switch to 1 5 or 10 minutes TEST 15 10 MIN For MANUAL OVERRIDE Flip the light switch off for one second then back on E Second OFF then Manual override works when the ON TIME switch is in any position Manual override only works at night because daylight n returns the sensor to A2. the shut off feature Do not point other lights at the sensor 150 6 ft ft Maximum Coverage Angle Maximum Range from bottom of 4 Screw fixture Z decorative a nut back on The detector is less sensitive to motion directly towards it Sensor Least Sensitive Most Sensitive g Walkthrough the coverage area noting where you are when the lights turn on Rotate the sensor head maximum Of 45 left or right to change the coverage area a 457 Maximum Sensor 45 Rotatation Maximum Aiming Range Set the amount of TIME you want the light to stay on after motion is detected OFF 3 6 DUSK TO TEST 1 5 10 MIN HOUR DAWN g Set the amount of time after dusk you want the lights on accent level SPECIFICATIONS Up to 30 feet varies during daylight hours Up to 150 240 aimable 3 60 W candelabra 400W 3 3 A total Power Requirements 120 VAC 60 Hz Operating Modes TEST AUTO and MANUAL OVERRIDE Sensing Angle Electrical Load Time Delay 1 5 10 minutes Accent timer Off 3 6 Hrs to dawn Sensitivity Adjustable The Heath Company reserves the right to discontinue products and to change specifications at any time without incurring any obligation to incorporate new features in products previously sold TROUBLESHOOTING GUIDE If you experience a problem follow
3. UTO ar a back on Mode Switching Summary TEST __ ON TIME Switch at 1 50r10 Turn E minutes light AUTA Flip light switch switch off for 10 off for 1 seconds L MANUAL OVERRIDE second then then on back on Wait one minute for sensor to warm up Dusk Accent Mode Light comes on half bright for selected time after dusk Off 3 hr 6 hr until dawn If motion is sensed the light turns on full bright for the ON TIME 1 5 or 10 minutes then returns to dim mode Printed in Hong Kong 595 5578 INSTALLATION O Turn power off at circuit breaker 2 Remove 1 Remove Mounting Plate two dase a One Motion Light S ii OPTIONAL WIRING BLACK BLACK 3 Set sensitivity range LIN on fixture back Two Motion Lights BLACK REDto BLACK Junction 4 Screw in mounting Box plate to junction box Standard Wiring to Motion Light amp Standard Fixture Horizontal Junction Boxes Only When wiring to additional standard A a fixture only Strip the motion sensor s Ls Ground red wire and connect to the standard Screw light s black wire Connect all white wires Fixture hi x Screw Ho Notch l So ais together Total fixture ratings must not a Jf Screw exceed 400W 3 3 A NS Junetion JJ X A sor
4. es Remove ground screw and 2 fixture screws i from the mounting plate Flip plate over and m a rotate 90 Re insert ground screw Insert the 2 fixture screws in the holes near the junction box screws holes Route wires through notch in adaptor plate f Slide the fixture onto the mounting screws m and tighten nuts er 1 Connect Bare wire to ground screw O Caulk fixture and mounting surface with silicone weather sealant J Install three 60W bulbs in candelabra style lights 2 White to white 3 Black to black Adding Decorative Tail 3g 2 Screw in exten sion bar 3 Add tail piece and 1 Remove LE decorative nut Xx TESTING Turn on the circuit breaker and light switch There is a one minute warm up before the sensor will detect motion prop erly g Switch the on time to TEST position and Dual Brite switch to the off posi a TEST 1 5 10 MIN OFF 3 6 DUSK TO HOUR DAWN Avoid aiming the control at e Pools of water or objects that change temperature rapidly such as heating vents and air conditioners These heat sources could cause false triggering e Areas where pets or traffic may trigger the control e Nearby large light colored objects re flecting daylight may trigger
5. not apply to you
6. s defined in the U S Consumer Product Warranty and Federal Trade Commission Improvement Act This warranty gives you specific legal rights and you may also have other rights which vary from state to state For a period of five years from the date of purchase any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you Light bulbs are not covered To obtain a refund or a replacement return the product to the place of purchase Not Covered Repair service adjustment and calibration due to misuse abuse or negligence light bulbs and other expendable items are not covered by this warranty Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety This warranty does not include reimbursement for inconvenience installation set up time loss of use or unauthorized service This warranty covers only Heath Zenith assembled products and is not extended to other equipment and components that a customer uses in conjunction with our products SUCH REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF HEATH FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS WHETHER OR NOT FORESEEABLE Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may
7. this guide If the problem persists call the assistance at 1 800 858 8501 8 00 AM and 4 45 PM EST weekdays Lo sentimos pero no podemos contestar preguntas en espa ol por tel fono SYMPTOM POSSIBLE CAUSE SYMPTOM POSSIBLE CAUSE Light will not 1 Light switch is turned off ff Light stays on 1 The sensor is pointed at come on Bulbis loose or burned out continuously nearby objects that cause Fuse is blown or circuit heat to trigger the sensor breaker is turned off Aim the sensoraway from Daylight turn off is in effect nearby objects recheck after dark The sensor is pointed Incorrect circuit wiring if toward a heat source like this is a new installation an air vent dryer vent or Re aim the sensor to cover brightly painted heat desired area reflective surface Re aim Light comes 1 Light Control may be in sensor on in day stalled in a relatively dark Light flashes 1 Heatbeingreflectedfrom light location on and off other objects may be Light Controlis in Test Set affecting the sensor Re control switch to an ON aim sensor Light comes 1 LigHE estiemay be sens Light Controlisinthe Test on for no ing small animals or automo mode and warming up apparent bile traffic re aim sensor Flashing is normal under reason Sensitivity is set too high these conditions Reduce sensitivity YOUR HEATH ZENITH FIVE YEAR LIMITED WARRANTY This is a Limited Warranty a
Download Pdf Manuals
Related Search