Harman Kardon MS 150 User's Manual
Contents
1. 20Hz 20kHz lt 0 01 System frequency response 65Hz 20kHz 3dB Frequency response OdBr 0 5 Signal to noise ratio WTG 75dB Channel separation gt 65dB Channel separation gt 600 Signal to noise ratio A WTG gt 100dBr Crosstalk between sources gt 60dB 22kHz filter gt 100dBr Line level input sensitivity at 1kHz 1 0V RMS 1dB Weight 9kg 19 8 Ib Loudspeakers Video Outputs Low frequency transducers Two 125mm 4 15 16 felted paper drivers ported Composite video 1 0V pk pk 75 ohms negative sync High frequency transducers Two 19mm 3 4 titanium laminate domes Nominal impedance 6 ohms Sensitivity 2 83V 1m 87dB Frequency response 80Hz 20 34 FM Tuner Section Frequency range 87 5 108 0MHz S Video Y 1 0V pk pk 75 ohms negative sync C 0 286V pk pk 75 ohms General Power requirement DC 24V 4 9A 5V 1A power supply works with AC 230V 50Hz Usable sensitivity IHF 1 3pV 13 2dBf Power consumption lt 1W standby 123W maximum both channels driven Signal to noise ratio Mono stereo 70 65dB Operating temperature 0 C to 35 C 32 F to 95 F Distortion Mono stereo 0 15 0 3 Stereo separation 35dB 1kHz 100 deviation 65dBf Dimensions H x W x D 252mm x 488mm x 194mm 9 5 16 x 19 1 4 x 7 5 8 Weight 8 2kg 18 08 Ib Selectivity2. see Step 2 of the Installation section Use caution and dispose of batteries according to environmental requirements Never throw the batteries into fire and remove them from the remote if it will be unused for a long period of time OF O gop Setting the Clock While the unit is in the Standby mode set the clock Press the Clock Adjust Mode button on the remote and use the A V buttons to set the correct hour minute and 12 24 hour format setting when they flash To change between AM and PM increase or decrease the hour setting Use the 4 1 buttons to move the cursor to the previous or next position and press the Clock Adjust Mode button again when you are finished See Figure 1 below Figure 1 Setting the Clock COREE Lef alcam Operation Turning On the MS 150 To turn on the MS 150 press the Power On button on the remote or press the On Standby button on the MS 150 s front panel The FM Radio will begin to play Setting the Alarm For automatic turn on at a programmed time set the alarm First press the Standby but ton to put the unit into the Standby mode you cannot set the alarm while the unit is on Press the Alarm Adjust Mode button on the remote and use the A V buttons to set the alarm time hour minute and 12 24 hour format setting and alarm source FM ra
3. 150 see step 4 on page 7 snap in the correct adapter and install a compatible iPod iPhone see page 7 On Standby Source Volume Up Volume Down Play Pause Memory Skip Scan Forward Skip Scan Reverse Headphone Jack AUX Line In 2 Dock for iPod iPhone Ly Install Here CD Slot 5 150 DC Power Input After making all other connections plug in the power supply Plug the included region specific power cord into the included power supply and into an unswitched wall outlet Analog Optical Digital Auxiliary Audio Input 1 Connect either the stereo mini plug cable or the optical digital audio cable both cables included here and connect the other end of the cable to a source device such as a portable CD player Connect the stereo mini plug cable only to the player s line level analog audio output or headphone jack and connect the optical cable only to an optical digital audio output Select the Analog 1 or Digital Audio source Auxiliary Analog Audio Input 3 Connect one end of a stereo RCA type interconnect cable not included here and connect the other end to the analog audio outputs on a source device such as a tape deck ANALOG IN OPTICAL Rear Panel Connections Subwoofer Output Connect this full range output to a powered subwoofer not includ ed equipped with a low pass filter for improved low frequency bass reproduction
4. 300kHz 65dB Image rejection 80dB IF rejection 90dB Tuner output level 1kHz 50kHz Dev 500mV Number of presets Six RDS capability PTY program type PS program service Text radio text Features specifications and appearance are subject to change without notice Please register your product at www harmankardon com You ll need your product s serial number 11 harman kardon SPS Os HARMAN HARMAN Consumer Inc 8500 Balboa Boulevard Northridge CA 91329 USA www harmankardon com 2011 HARMAN International Industries Incorporated All rights reserved Harman Kardon is a trademark of HARMAN International Industries Incorporated registered in the United States and or other countries iPhone iPod iPod classic iPod nano and iPod touch are trademarks of Apple Inc registered in the U S and other countries Made for iPod and Made for iPhone mean that an electronic accessory has been designed to connect specifically to iPod or iPhone respectively and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards iPod and iPhone not included Part 950 0352 001 Rev A harman kardon by HARMAN www harmankardon com
5. and service The MS 150 does not respond to remote commands The batteries in the remote control may require replacement The IR sensor may be blocked The sensor is located in the middle of the front grille about 25mm 1 in above the CD slot The tuner is buzzing intermittently Adjust the placement of the antenna to improve reception Check that the antenna is securely connected to the rear panel terminal No video image Check that the TV is securely connected to either the S Video or Composite Video output but not both The TV Out setting on the iPod iPhone must be turned on Video is available only when the dock for an iPod iPhone has been selected as the source and then only when a compatible iPod iPhone model that is capable of video browsing is docked The TV Out setting on the iPod iPhone must be turned on There must be photo or video content stored on the iPod iPhone Select the correct video input on the TV view photos press the button three times You can find additional troubleshooting information by clicking on the FAQs link on the Support page at www harmankardon com 10 MS 150 Technical Specifications Specifications System CD Section Power output 30 watts per channel 20Hz 20kHz THD Disc compatibility CD CD R CD RW enhanced CD lt 0 07 into 6 ohms both channels driven MP3 WMA Bandwidth 57Hz 27kHz 69
6. or connect it to an external amplifier or powered speakers Composite and S Video Outputs Connect either of these outputs to a TV or video display for viewing videos or photos stored on a compatible iPod iPhone that supports video browsing No other displays are available through these outputs FM Antenna Terminal Connect the included FM antenna wire here ANALOG OPTICAL AUXILIARY ANALOG SUBWOOFER S VIDEO VIDEO USB OUTPUT FM ANTENNA DC Power Inout DIGITADAUXIOMRYI AUDAUMIEE In 0 OUTRBUDWooferOUTRUVideo TERMINAM Antenna DC Power Input Digital Output Output Video Output Terminal AUX Line In 1 MS 150 Standby This button s function depends on the MS 150 s on Standby state When the MS 150 is on pressing this button powers it down to the Standby mode power is available only to the clock and alarm functions When the MS 150 is the Standby mode pressing this button toggles the display brightness between normal and dim When you turn the MS 150 on the display brightness will be at the new setting NOTE To power the MS 150 off completely unplug the power supply from the AC outlet Power On Press this button to turn the MS 150 on Skip Scan Forward Reverse These buttons functions depend on which source has been selected iPod iPhone or CD Press and release a button to skip to the next track or to the beginning of the current track Press the reverse button twice to skip t
7. Mo 150 High performance stereo music system harman kardon by HARMAN Made for 5 iPod HiPhone Ms 150 INTRODUCTION DESCRIPTION SUPPLIED ACCESSORIES FRONT PANEL CONTROLS REAR PANEL CONNECTIONS REMOTE CONTROL FUNCTIONS INSTALLATION OPERATION USING THE REMOTE CONTROL SETTING THE CLOCK TURNING ON THE MS 150 SETTING THE ALARM SETTING THE ALARM VOLUME SETTING THE EQUALIZATION EQ VOLUME CONTROL SOURCE SELECTION FM RADIO PROGRAM STATION PRESETS CD PLAYBACK CONTROL DATA DISCS AUXILIARY INPUTS DOCK FOR iPod iPhone PHOTO AND VIDEO PLAYBACK UNDOCKING THE iPod iPhone TROUBLESHOOTING GUIDE TECHNICAL SPECIFICATIONS TRADEMARK ATTRIBUTIONS oOo O O O MS 150 Introduction More than 50 years ago we sold the very first audio receiver a high perfor mance component that combined the functions of several products that had previously been available only separately Our mission was and is to deliver high fidelity sound in an easy to use package and we are confident that you will enjoy the quality and convenience of the MS 150 music system for many years to come The MS 150 is a complete high performance audio system with a CD player FM tuner dock for iPod iPhone devices not included auxiliary inputs for other audio products and built in loudspeakers for a complete audio solution To obtain the maximum enjoyment from your new syst
8. alization modes TABLE the default and WALL Use the TABLE setting when the MS 150 is free standing Change the setting to WALL if the MS 150 is located against a wall to reduce the bass and optimize audio quality co Left TAER PEEP EEL MS 150 To change the EQ mode place the MS 150 in the Standby mode Then press the Source button The SETTINGS menu appears in the MS 150 Message Display Press the but ton to toggle between the ALARM VOLUME and EQ menu options When EQ is displayed use the or button to toggle between TABLE and WALL Press the Source button to save your selection Volume Control Use the front panel or remote Volume controls to raise or lower the volume The default setting at turn on is 12 and the maximum setting is 30 Use caution with volume levels to avoid damage to your hearing or equipment The volume level appears in the Message Display when the Volume controls are used To silence playback temporarily press the Mute button on the remote or simultane ously press the front panel Volume Up and Down buttons Mute will flash in the Message Display Press the Mute button or either Volume control to resume normal volume Source playback will continue during muting Source Selection The first time the MS 150 is turned on it will default to FM Radio Each press of the Source Selector switches to the next source in thi
9. c is not compatible with the MS 150 or its data may be damaged Press the Eject button to remove it In normal operation the disc will automatically begin playing when you select CD as the source The Play icon will appear along with the current and total track numbers and the elapsed track time When the disc has finished playing the Stop icon will appear with the total number of tracks and total disc time Playback Control To pause playback momentarily for later resumption at the same point press the Play Pause Memory button Press the button again to resume play The Pause icon will be displayed Press and hold the Play Pause Memory button for two seconds to stop playback fully To search at 10x speed through the current track press and hold the Skip Scan Forward or Skip Scan Reverse button When the track s beginning or end is reached normal play will begin To skip to the next track tap the Skip Scan Forward button If the current track is the last one on the disc the MS 150 will skip to the first track To return to the beginning of the current track tap the Skip Scan Reverse button Tap it twice quickly to skip backwards to the previous track For repeat or random shuffle play press the Playback Mode button Each press changes the playback mode as follows Repeat 1 Track Repeat All Tracks Shuffle Shuffle with Repeat All and Normal Playback Data Discs When an MP3 or WMA disc is loaded the di
10. d iPhone source Playback will begin automatically with the first track stored on the iPod iPhone The transport controls work as they do for CDs To pause or restart play press the Play Pause Memory button To search forward or reverse through a track press and hold the Skip Scan Forward or Reverse button To skip forward or reverse through the tracks tap the Skip Scan Forward Reverse button Repeat and Random Play are available Each press of the Playback Mode button switches the mode as follows Repeat 1 Track Repeat All Tracks in the current playl ist Shuffle Aloums Shuffle Aloums with Repeat All Shuffle Tracks Shuffle Tracks with Repeat All and Normal Play Operation To navigate the menus on the iPod iPhone Press the 4 button to display the menu or return to the previous menu level Press the button to select the current item Press the A V buttons to scroll up or down During play the current track and total number of tracks in the current playlist will display alternately with the elapsed and total times If available the artist and track name will also appear Photo and Video Playback If the iPod iPhone supports video browsing navigate its menu system to select a video for viewing on a TV connected to one of the MS 150 s video outputs Make sure the TV Out setting on the iPod iPhone is turned on Press the gt button and the video will begin playing To view photos navigate
11. dio CD player iPod iPhone in dock as they flash To change between AM and PM increase or decrease the hour setting Use the lt P gt buttons to move the cursor to the previous or next setting arm the alarm use the A V buttons to change the Alarm message to Alarm On and press the Alarm Adjust Mode button again when you are finished The Timer indicator will appear in the Message Display when the alarm has been set See Figure 2 below At the set time the MS 150 will automatically turn on and begin playing the selected source If CD or iPod iPhone was selected and there is no disc loaded or iPod iPhone docked the MS 150 will switch to the FM radio source Play will begin at the set volume level for 10 minutes and then shut off automatically Press any button to place the unit in Snooze mode The alarm will remain off for 9 minutes then it will resume Press and hold the On button while the alarm is playing to turn it off and return to normal play Setting the Alarm Volume The default alarm volume level is 12 To change the alarm volume level place the MS 150 in the Standby mode Then press the Source button The SETTINGS menu appears in the MS 150 Message Display Press the button to toggle between the ALARM VOLUME and EQ menu options When ALARM VOLUME is displayed use the A V buttons to set the volume level 0 30 Press the Source button to save your selection Setting the Equalization EQ The MS 150 has two equ
12. em we urge you to read this manual and refer back to it to familiarize yourself with the MS 150 s features and operation If you have any questions about this product its installation or its operation please contact your retailer or custom installer or visit www harmankardon com Harman Kardon MS 150 High Performance Audio System Universal dock for iPod iPhone not included charges most docking iPod and iPhone models For the latest compatibility information please visit our Web site www harmankardon com Slot loaded CD player with CD CD R CD RW enhanced CD MP3 and WMA playback FM tuner with RDS text display and six presets Four auxiliary audio inputs front panel stereo mini jack 3 5mm rear panel stereo mini jack 3 5mm for line level or optical digital audio rear panel dual RCA jacks line level Two two way 125mm 4 5 16 built in bass reflex speakers Subwoofer output full range 3 5mm 1 8 stereo headphone output Composite and S Video outputs for photo and video capable iPod iPhone models that support video browsing Clock with alarm and memory backup iPod iPhone not included Introduction Description Supplied Accessories Supplied Accessories The following accessory items are supplied with the MS 150 If any of these items are missing please contact Harman Kardon customer service at www harmankardon com FM wire antenna 1m 39 3 8 male to male cable with 3 5mm 1 8 s
13. ge will appear and you must erase an old preset before a new one can be stored If the currently tuned station has previously been programmed as a preset pressing the button for two seconds will erase the preset Message Display Front Panel Controls Skip Scan Forward Reverse These buttons functions depend on the current source iPod iPhone or CD Press and release the buttons to skip to the next track or to the beginning of the current track Press the Reverse button twice to skip to the previous track Press and hold a button to scan forward or reverse within a track FM Radio Press and release a button to tune to the next higher or lower station by one frequency increment Press and hold a button to scan quickly through the stations When you release the button in Auto tuning mode the tuner continues to scan until it finds a station of acceptably strong signal quality and then it stops In Manual tuning mode the tuner stops immediately at the current frequency Headphone Jack Outputs a stereo signal for private listening through most headphones that are equipped with a 3 5mm 1 8 plug AUX IN Jack Analog Input 2 Connect the included 3 5mm male to male cable to the headphone or line level output on a portable player or other device CD Slot Load compatible discs here Eject When a CD is loaded press this button to eject it Dock for iPod iPhone Gently insert the dock into the opening on the left side of the MS
14. ntenna the analog and digital audio cables the power supply and detachable cable the dock for iPod iPhone and inserts and the remote control and batteries 2 Install the batteries in the remote control following the and symbols in the battery compartment to maintain the correct polarity CAUTION There is danger of an explosion if a battery is incorrectly replaced Replace only with the same or equivalent type MANNA NNN NN NNN 3 Connect the FM antenna to its terminal 4 Plug the detachable dock for iPod iPhone into the connector on the left side of the MS 150 Snap in the adapter that matches your iPod iPhone referring to the table below DC IN 24 5A 120W To remove an adapter insert a flathead screwdriver into the slot at the rear of the adapter and pry it up Installation 5 The MS 150 features four audio inputs for other devices such as portable players This step is optional and may be skipped if you have no external devices If you have a player with 3 5mm 1 8 analog audio output or headphone jack Plug the included analog audio cable into the player s output or headphone jack and either the front or rear panel mini jack on the MS 150 Both inputs may be used simultaneously for different devices A second cable must be purchased Pair of RCA type analog audio out
15. o the previ ous track Press and hold a button to scan forward or in reverse within a track FM Radio See Tuning on this page Play Pause Memory This button s function depends on which source has been selected iPod iPhone or CD Each press of the button toggles between the Play and Pause functions Press and hold the button to stop playback fully FM Radio If the currently tuned station has not been programmed into a preset pressing the button stores the station as a preset If all of the preset positions have been used the Full message will appear and you must erase an old pre set before a new one can be stored If the currently tuned station has previously been programmed as a preset pressing the button for two seconds will erase the preset Source Select This button s function depends on the MS 150 s on Standby state When the MS 150 is on each press of the button changes the current source in this order FM CD AUX LINE IN 1 rear panel 3 5mm analog input AUX LINE IN 2 front panel AUX LINE IN 3 rear panel dual RCA jacks AUX DIGITAL IN iPod iPhone When the MS 150 is in Standby mode the SETTINGS menu is displayed in the Message Display Use the 4 1 buttons to toggle between the ALARM VOLUME and EQ options Use the A V buttons within each option to change the setting Press the Source button again to save your selection Tuning Mode When FM Radio is the selected source each press
16. of the button toggles between Auto and Manual tuning Playback Mode When iPod iPhone or CD is the selected source each press changes the repeat and random shuffle playback mode See page 9 for the modes available with each source When the MS 150 in the Standby mode or when the source is changed the playback mode returns to Normal Sleep Each press increases the time until turn off from 10 to 90 minutes in increments of 10 minutes The next press after the 90 minutes setting turns off the Sleep function Remote Control Functions Clock Adjust Mode With the MS 150 in the Standby mode press this button to adjust the clock Use the A V Navigation buttons to adjust the hour minute and 12 24 set tings To change between AM and PM increase or decrease the hour Press the lt gt buttons to move the cursor to the previous or next position Press this button again at any time when finished Alarm Adjust Mode With the MS 150 in Standby mode press this button to adjust the alarm Use the A V Navigation buttons to adjust the hour minute 12 24 and wake up source settings To change between AM and PM increase or decrease the hour Press the lt gt buttons to move the cursor to the previous or next position Press this button again at any time when finished Preset Search When FM radio is the selected source press this button to select the next or previous preset station if any have been programmed Eject When a CD is loaded pres
17. played Program Station Presets To program a preset for quick access to favorite stations tune to the station s frequency and press and hold the Play Pause Memory button for two seconds The preset will appear If no station has been programmed into the preset the current station will be stored If a different station was previously programmed it will be overwritten by the new station To select a new preset use the Preset Up Down buttons six presets are available If all six have been programmed you must overwrite or erase one to program a new station preset If the current station was stored in the preset position the preset will be erased Operation cD First press the Eject button to ensure that the CD slot is empty Then gently insert a CD CD R CD RW enhanced CD MP3 or WMA disc label side up partway into the slot The loading mechanism will detect the disc and pull it the rest of the way in Do not attempt to force the disc If the disc will not load turn off the MS 150 unplug it and bring it to an authorized Harman Kardon service center for inspection If another source is playing the MS 150 will not automatically switch to the CD Press the Source Selector button repeatedly until CD is selected The Reading message will appear for a few moments while the MS 150 identifies the disc type The correct indicator will appear in the Message Display NOTE If the Error message appears the dis
18. puts Plug one end of a stereo RCA type interconnect cable not included into the player and the other end into the Auxiliary Input jacks on the rear panel of the MS 150 Use the same color connector for each channel usually red for right and white or black for left Optical digital audio S P DIF output Plug one end of the included digital audio cable into the player and the other end into the Analog Optical input on the rear panel of the MS 150 Remember to select the digital input as the source 6 If you have purchased an optional powered subwoofer that is equipped with a line level input and a low pass filter crossover connect it to the Subwoofer output cable not included or connect this output to an amplifier s or powered speaker s line level input 7 If you will be viewing photos or videos stored on a compatible iPod iPhone that sup ports video browsing connect either the Composite or S Video output but not both to a display monitor 8 Plug the included power supply into the MS 150 s DC IN connector and plug its power cord into an unswitched AC outlet MS 150 Using the Remote Control Aim the remote at the front of the MS 150 The remote IR sensor is located in the middle of the front panel behind the mesh grille about 25mm 1 in above the CD slot Do not block the sensor The remote has a range of approximately 6m 20 ft up to 30 degrees off center If the batteries require replacement
19. s order FM CD AUX LINE IN 1 rear panel 3 5mm analog input AUX LINE IN 2 front panel AUX LINE IN 3 rear panel dual RCA jacks AUX DIGITAL IN iPod iPhone Subsequently when you turn the MS 150 on it will select the last source used before you placed it in the Standby mode FM Radio Press the Tuning Mode button to select Automatic or Manual tuning The AUTO indicator appears when Auto tuning is active In Auto tuning mode pressing the Tuning Up and Down buttons causes the radio to scan in the selected direction for a signal with acceptable strength then stop The radio will also stop if you press one of the Tuning buttons again In Manual tuning mode each press of the Tuning Up and Down buttons causes the radio to tune to the next frequency in the selected direction If a stereo signal is detected the STEREO indicator will light Monaural stations or weak stereo stations will be played in mono NOTE To cancel programming or erasing of a preset press any other key To select a preset station use the Preset Search buttons Ifthe station is broadcasting RDS Radio Data System information the information will be dis played The second line of the Message Display may show the station s call letters aname or other information depending on what the station broadcasts The third line indicates the Program Type PTY when broadcast When no RDS information is available only the station s broadcast frequency will be dis
20. s this button to eject it Tuning When FM radio is the selected source press and release this button to tune to the next higher or lower station by one frequency increment Press and hold this button to scan quickly through the stations When you release the button if Auto tuning mode is active the radio continues to scan until it finds a station of acceptably strong signal quality and then it stops In Manual tuning mode the radio stops immediately at the current frequency A lt gt Navigation buttons These buttons are used with an iPod iPhone to navi gate its menus or in Standby mode to adjust the clock or alarm The A V buttons are used for scrolling Press the button to select the current item and the 4 button to display the menu or return to the previous menu screen Mute Press this button to silence the speakers temporarily Press the button again to restore audio Powering down the MS 150 to the Standby mode cancels the muting Volume Controls Momentarily press these buttons to increase or decrease the volume Press and hold either button to change the volume more quickly STANDBY Standby Power On Play Pause Memory Track Skip Scan Tuning Mode Tuning Up Down Source Select Playback Mode Clock Adjust Mode Sleep Alarm Adjust Mode Eject Preset Search Tuning lt gt Navigation Mute lt Volume Controls oe harman kardon MS 150 MS 150 1 Carefully unpack the MS 150 the FM a
21. sc type indicator will light up and the number of folders and tracks in the current folder will be displayed Play will begin automatically If the disc has both and WMA tracks both indicators will light For MP3 discs the track name and artist will alternate in the display For WMA discs the album and track number will alternate in the display For both disc types the Skip Scan Repeat and Random play functions are the same as for audio CDs JPEG discs are not compatible with the MS 150 and the display will indicate that they have no files and no folders Auxiliary Inputs The MS 150 is equipped with three analog audio inputs and one digital audio input If you have connected a compatible device such as a portable audio player or a cassette deck select the corresponding auxiliary input as the source and use the device s own controls AUX LINE IN 1 Analog rear panel 3 5mm jack shared with Digital Input AUX LINE IN 2 Analog front panel 3 5mm jack AUX LINE IN 3 Analog dual rear panel RCA type jacks DIGITAL LINE rear panel 3 5mm jack MS 150 Dock for iPod iPhone The MS 150 dock is compatible with most docking iPod and iPhone models For the latest compatibility information please visit our Web site www harmankardon com Install the detachable dock and appropriate adapter as described in the Installation sec tion on page 7 then dock the iPod iPhone Use the Source Selector to select the iPo
22. tereo mini plug Mini 3 5mm optical digital External power supply 24V 4 9 5 1A audio cable 1m with detachable power cord System remote control with Detachable dock for iPod iPhone two AAA batteries with five adapters 0 MS 150 Message Display The time and messages are displayed on top of the unit On Standby Press this button to turn the MS 150 on or to place it in the Standby mode Press and hold the button for two seconds to disarm the alarm To power off the unit completely unplug the power supply Source Each press of the button changes the currently playing source in this order FM CD AUX LINE IN 1 rear panel 3 5mm analog input AUX LINE IN 2 front panel AUX LINE IN 3 rear panel dual RCA jacks AUX DIGITAL IN iPod iPhone Volume Controls Press the buttons to increase or decrease the volume Press and hold the buttons to change the volume more quickly Press both buttons together to mute Play Pause Memory This button s function depends on which source has been selected iPod iPhone or CD Each press of the button toggles between the Play and Pause functions Press and hold the button to stop playback fully FM Radio If the currently tuned station has not been programmed into a preset pressing the button stores it as a preset If all of the preset positions have been used the Full messa
23. to the desired library or image and press the button three times After a few moments a slideshow of the images in the selected library will appear on the TV Undocking the iPod iPhone You may undock the iPod iPhone at any time as long as playback has been stopped To remove the dock adapter e g to switch adapters for a different iPod iPhone model insert a flathead screwdriver into the slot at the rear of the adapter and pry it up Refer to the illustration in the Installation section on page 7 Troubleshooting Guide Symptom Unit does not function when the Power On button is pushed Solution Make sure the AC power cord is securely plugged into a unswitched outlet If the PROTECT message appears turn off the MS 150 and unplug it Do not use it without first bringing it to an authorized Harman Kardon service center for inspection The display lights up but there s no sound Press the Mute button to make sure the system is not muted Turn up the volume Check that the correct source was selected If the source is an external device make sure it is plugged in turned on and playing and that it is properly connected to one of the auxiliary inputs headphones are in use unplug them There is sound on only one side or the sound is distorted There may be a problem with one of the built in speakers Bring the MS 150 to authorized Harman Kardon service center for inspection
Download Pdf Manuals
Related Search