Harman Kardon Drive+Play User's Manual
Contents
1. continued on next page Control Knob Cable Through 0 Base and Internal Mounting Plate INSTALLATION 7 drive Installing Components Installing the Control Knob continued 2 At the base below the cable using the 1 5mm hex key loosen but do not remove the hex setscrew 3 To install the Control Knob with adhesive tape perform the following steps or skip to step 4 a Insert the mounting plate rotate it 180 and tighten the hex setscrew Control Knob With 0 Base y Mounting Plate l Adhesive S i b At the site wipe the surface and exposed mounting plate with one of the enclosed alcohol pads Allow both to dry c Remove the protective tape from one side of one of the enclosed adhesive pads and press the pad against the mounting plate d Remove the remaining protective tape and press and hold the Control Knob to its site for 5 seconds 4 To install the Control Knob with mounting screws perform the following steps a At the proposed site place the mounting plate and rotate it so that the arrow will point toward the hex set screw at the back of the base after it s mounted b Holding the mounting plate in position fasten it to the surface with three enclosed mounting screws c Using the mounting plate s center hole as a template drill a hole through the mounting surface and pass the Control Knob s cable through the hole d Place the Control Knob on the mounting plate2. 180 from its final position and then rotate it a half turn to the final position Tighten the hex setscrew at the back of the base 8 INSTALLATION OPERATION Control Knob With 0 Base Mounting Plate 5 Route the attached cable to the Electronics Enclosure Installing the iPod Cable Route the iPod dock connector cable to the chosen iPod site e g the center console compartment or the glove box Be sure to leave enough cable exposed to make connecting and disconnecting the iPod easy Making the System Connections With all power off refer to the Wiring Diagram on page 5 and make only the power ground and audio signal connections that apply to the scheme you have chosen After verifying all connections including the iPod proceed to the next section Operating Drive Play OPERATING DRIVE PLAY Distraction Warning Do not connect or disconnect your iPod or program Drive Play while driving Always pull off the road and park in a position that you are absolutely sure presents no risk before browsing your iPod or adjusting the settings on your Drive Play Always obey all traffic laws while driving Overview Menu Press Once to Jump to Last Screen Scroll Ring Scroll Left Once to Last Menu Item Scroll Left and Hold to Jump Back In Now Playing Scroll Left to Fast Rewind Scroll Ring Scroll Right Once to Next Menu Item Scroll Right and Hold to Jump Forward In Now Playing Scroll Right to F
3. Output Voltage 1V Maximum Auxiliary Input Voltage 1V Audio Input and Output Jacks 3 5mm stereo mini plug All features and specifications are subject to change without notice Harman Kardon and Harman International are registered trademarks and Drive Play is a trademark of Harman International Industries Incorporated Apple and iPod are registered trademarks of Apple Computer Inc Information for the User This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for Class B Digital Device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protec tion against harmful interference in a residential installation This equipment generates and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following me
4. album OPERATION Now Playing Song Title Artist NOTE Now Playing Playlists Artists Albums Songs Genres or Composers will only appear in the Main Menu after they have been checked for display see the previous page Browsing Playlists Drive Play Menu gt Playlists gt select a playlist e g Favorites gt select a song NOTE The On The Go playlist will not be updated while using Drive Play Browsing Artists Drive Play Menu gt Artists gt select an artist gt select an album gt select a song Browsing Albums Drive Play Menu gt Albums gt select an album gt select a song Browsing Songs Drive Play Menu gt Songs gt select a song Browsing Genres Drive Play Menu gt Genres gt select a genre gt select an artist gt select an album gt select a song Browsing Composers Drive Play Menu gt Composer gt select a composer gt select an album gt select a song Shuffle Play You can set Drive Play to shuffle randomly play iPod songs or albums as follows Drive Play Menu gt Settings gt Shuffle gt select Off default Songs or Albums Repeat Play You can set Drive Play to repeat the current iPod song or all songs in a playlist or album as follows NOTE When browsing by Artists Genres or Composers select ing Repeat All will repeat the album containing the desired song Drive Play Menu gt Settings gt Shuffle g
5. device e g cell phone or satellite radio see Wiring Diagram on page 5 connected to Drive Play s auxiliary input to your mobile audio system e To enable or disable automatic sensing and switching of audio signals on Drive Play s auxiliary input Drive Play Menu gt Settings gt select Auto audio sense check box to enable or to disable default it e To select Auxiliary input signals manually with iPod con nected 1 Drive Play Menu gt Settings gt AUX input 2 Go Back on will appear e To restore audio from the iPod manually with iPod con nected 1 Drive Play Menu gt Settings gt Go Back on 2 Audio from the iPod will be restored and the Settings Menu will appear e To enable disable AUX input manually when no iPod is connected 1 Turn on the Drive Play Aux is Disabled is highlighted 2 Press center Select button once to enable AUX input Listening to AUX message will appear 3 Press Select button again to disable AUX input Aux is Disabled message will appear Setting the Display You can customize Drive Play to display your viewing pref erences as follows e To enable or disable Large Fonts 1 Drive Play Menu gt Settings gt Display Settings gt select Large Font check box to turn it on or off default 2 To enable or disable Large Fonts press the top Menu button twice to return to the Drive Play menu NOTE When Large Fonts is disabled unchecked t
6. for the audio interface Text Display Location The Text Display shows current iPod information and is similar to the display on your iPod It comes with a three position pivot arm for virtually limitless viewing adjustment You can install the unit in a variety of locations as long as the pro posed site offers a direct view of the display For easiest view ing mount the unit near other instrument panel gauges or on top of the dashboard Control Knob Location The Control Knob allows you to control the iPod much like the iPod Click Wheel The unit comes with three interchangeable bases so you can choose the most comfortable operation angle Ideally you should install the Control Knob in a location that pro vides comfortable access while driving where you can easily feel and operate it without taking your eyes off the road continued on next page INSTALLATION 3 drive Choosing Installation Locations continued Electronics Enclosure Location The Electronics Enclosure contains the wireless FM transmitter and the power supply for the three components You can install it under a seat in the center console compartment or in the glove box If possible select a site that provides both conven ient access to the enclosure and easy cable routing Drive Play also provides an audio interface to a cell phone satellite radio or any other device that outputs a low level audio signal using the Aux In jack When using the Auxiliar
7. FM Settings can be accessed from the Main Menu or later within the Settings Menu e To turn FM Transmission on or off Drive Play Menu gt FM Settings gt FM Transmitter gt select On default or Off e To change the preset FM Frequency Drive Play Menu gt FM Settings gt FM Frequency gt select 88 1 default 88 3 88 5 88 7 88 9 or Custom default 91 7MHz or last setting NOTE If the preset FM frequencies are already assigned to FM stations in your listening area then use Custom FM Frequency below to select an unused frequency The default setting is 91 7MHz e To select a Custom FM Frequency 1 Drive Play Menu gt FM Settings gt Custom Frequency 2 The FM Frequency graphic display will appear Scroll to select a desired FM frequency Setting Shuffle You can set Drive Play to shuffle randomly play iPod songs or albums as follows Drive Play Menu gt Settings gt Shuffle gt select Off default Songs or Albums Setting Repeat You can set Drive Play to repeat the current iPod song or all songs in a playlist or album as follows NOTE When browsing by Artists Genres or Composers selecting Repeat All will repeat the album that contains the selected song Drive Play Menu gt Settings gt Shuffle gt select Off default gt One gt All continued on next page OPERATION 9 drive Initial Setup continued Setting AUX Input To route an audio signal from a
8. Play this product is designed for do it yourself installation as well especially when using the wireless FM transmission method see page 4 Although the enclosed instructions explain how to install the Drive Play in a general sense they do not show the exact methods for your particular vehicle After reading the manual if you feel uncomfortable in performing the necessary steps to install the product consider asking your car audio dealer about professional installation options INSTALLATION Parts List Drive Play includes the following components and parts Text Display With Universal Mounting Base and Attached Cable 3m Control Knob With 30 Mounting Base and Attached Cable 3m Electronics Enclosure the Brain 12 Volt Accessory Power Cable 2m With Cigarette Lighter Adaptor 12 Volt Power Harness 0 5m With In Line Fuse Holder for direct connection to the vehicle s electrical system Line Out Cable 1 6m Stereo 3 5mm M Plug to L R RCA M Plugs jPod Cable 3m 8 Pin Mini DIN M Plug to iPod Dock Connector 2 Control Knob Bases 0 and 60 2 Mounting Plates for Knob Base and Display Base 10 Mounting Screws 3 Knob Base 3 Display Base and 4 Electronics Enclosure 6 Cable Ties Black 2 Hex Keys 3mm and 1 5mm 2 Adhesive Mounting Pads 2 Alcohol Prep Pads Warranty Card Tools and Precautions To install Drive Play components we recommend using t
9. a different jump size as follows Drive Play Menu gt Settings gt Jump Size gt select 5 10 default 15 20 or 25 About Drive Play You can view information about Drive Play as follows Drive Play Menu gt Settings gt About Resetting All Settings NOTE Resetting all settings will erase all your custom set tings and replace them with default values To reset all Drive Play settings to their default values 1 Drive Play Menu gt Settings gt Reset All 2 After a few seconds you will see the Harman Kardon splash screen followed by the Now Playing screen At this point all Drive Play settings have been reset Browsing and Playing Songs Browsing and playing songs using Drive Play works much like an iPod Using the Control Knob see Overview on page 8 you can play songs in any playlist or play songs in categories such as Artists Albums Songs Genres or Composers NOTE Drive Play does not support chapter search when playing an Audiobook You may use the scroll wheel to move forward or backward manually Press the center Select Button to advance through menu items to locate and play songs Press the top Menu Button to go back to a previous menu When a song starts to play the Text Display will show the Now Playing screen see above right with Song Name Artist track number and the elapsed play time You can also set Drive Play to shuffle play or repeat play a song or
10. ast Forward Next Fast Forward Press Once to Play Next Track Previous Rewind lA Press Once to Play Last Track NN Play Pause Press Once to Stop or Resume Play of Current Track Select Press Once to Choose Highlighted Menu Item Drive Play operates much like the iPod itself The Control Knob mimics the iPod s Click Wheel and its software uses a similar menu select system Before you use Drive Play you ll need to set it up for the first time After you perform the Initial Setup using the Settings Menu controlling your iPod with Drive Play will be easy and intuitive To make selections on the Text Display you simply turn the Control Knob s Scroll Ring to highlight a desired menu item Turn the Scroll Ring to the right to scroll down and to the left to scroll up Press the center Select button once to confirm your selection Depending on your selection this display may show e alist of settings or menu operation or When in any of the settings menus e a highlighted setting with a choice of values or a highlighted setting with a check box or agraphic display which may be adjusted using the Scroll Ring Pressing the center Select button again will select the next highlighted setting to the right or go back to the beginning if all settings have been viewed or set the check box on or off i e check or uncheck If a graphic display appears use the Scroll Ring to adjust the setting After making yo
11. asures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment harman kardon drive 250 Crossways Park Drive Woodbury New York 11797 www harmankardon com 2005 Harman International Industries Incorporated All rights reserved Part No 950 0081 001 revB H A Harman International Company
12. check box to enable or disable default it Setting the Drive Play Main Menu You can set the Drive Play Main Menu to display your choice of menus as follows NOTE As a default the following eight menus will be displayed denoted by checked boxes FM Settings Now Playing Playlists Artists Albums Songs Genres and Composers If you want all these selections to display then Skip this section 1 Drive Play Menu gt Settings gt Change Main Menu 2 Scroll to a selection e g Composers you want to remove and press the center Select Button once to uncheck the box To add the menu again press the center Select Button once to check the box 3 Repeat step 2 for other menus you want to remove from or add to the Main Menu Setting the Sleep Timer Drive Play is equipped with a sleep timer that delays its power off by a default of 2 seconds after the ignition is turned off You can set a different delay time as follows NOTE Sleep Timer only works when the Drive Play s ACC wire is connected to the ignition switch s accessory terminal see Wiring Diagram on page 5 Drive Play Menu gt Settings gt Sleep Timer gt select 2 sec default 4 sec or 8 sec Setting the Jump Size When browsing a database songs albums artists etc you can scroll and hold to jump to a different position in the list skipping over undesired titles The default jump size is 10 percent of your database You can set
13. erface is required for a CD changer interface If your system has neither feature FM transmission is the only choice for the audio interface Choosing a Power Interface Referring to the Wiring Diagram on the next page you can connect Drive Play s power connections to your vehicle s electrical system in one of two ways Removable 12 Volt Accessory Power Cable With Cigarette Lighter Adaptor This power interface is the most convenient since the power cable can be simply plugged into the vehicle s cigarette lighter outlet No additional wiring is required The cigarette lighter adaptor is fuse protected and the fuse can be changed by removing the adaptor s end nut NOTE If your cigarette lighter works even when the car s ignition switch is in the off position you ll have to turn Drive Play on manually It can be turned off manually or it will shut off automatically after one hour of inactivity Wiring Diagram INSTALLATION iPod Text Display Coney Knob Audio Input Output Jacks Tip LEFT BIGHT IRing Sleeve GROUND iPod Cable Electronics Enclosure Fos oc or 12 Volt Power Harness 3 5mm Stereo Mini Plug Cable Head Unit Radio Wireless FM Transmitter or Antenna In t Line Out Cable Third Party Aux L R In or JP m CD Changer 2A Fuse 3 5mm Stereo Cable not included Interface opti
14. harman kardon drive play Owner s Manual drive INTRODUCTION Thank you for purchasing Harman Kardon s Drive Play an elegant mobile audio solution that provides the driver with total iPod control including full music browsing capability We ve organized this manual to make installation and operation as simple and trouble free as possible Please read it thoroughly before you begin installing Drive Play Remember to keep your sales receipt with this manual in a safe place so both are avail able for future reference If you have any questions about the installation please contact us at 1 516 255 HKHK 4545 Or on the Web at www harmankardon com iPod Requirements Drive Play is designed to work with all iPods equipped with the following Apple hardware and software 1 iPod dock port iPod Dock Port 2 iPod software Model Description and Minimum Software Version Date 3G Buttons above touch wheel v2 2 2 04 As long as both of these requirements are met Drive Play can be easily added to virtually any mobile audio system for total control of your iPod 2 INTRODUCTION Drive Play Warnings Distraction Warning Do not connect or disconnect your iPod or program Drive Play while driving Always be careful and attentive to your vehicle and the traffic around you Always obey all traffic laws while driving Always pull off the road and park in a position you are sure p
15. he Now Playing screen can display up to 32 characters When Large Fonts is enabled checked the first 16 characters will be displayed and you can press the center Select button to display the next 16 characters and again to display the first 16 or use Auto Scroll see next item 10 OPERATION e When Large Fonts are enabled you can also enable or disable Auto Scroll which automatically scrolls a text message longer than 16 characters in the Now Playing screen Drive Play Menu gt Settings gt Display Settings gt Auto Scroll gt select On or Off default e To adjust the display s contrast 1 Drive Play Menu gt Settings gt Display Settings gt Adjust Contrast 2 The Contrast graphic display will appear Scroll to select a desired contrast e To adjust the display s backlight 1 Drive Play Menu gt Settings gt Display Settings gt Adjust Backlight 2 The Brightness graphic display will appear Scroll to select a desired brightness e You can set Drive Play s backlight to turn off after 10 seconds When it is off pressing any button on the Control Knob will turn it back on To turn the display s backlight timer on or off Drive Play Menu gt Settings gt Display Settings gt Backlight Timer gt select On default is always on or 10 sec e To enable or disable an inverted display i e white text on black background Drive Play Menu gt Settings gt select Display Settings
16. he following tools Electric or cordless drill with drill bit set Phillips screwdriver set Pencil Protective eyewear Before starting the installation please observe the following precautions Turn off all audio system power including the iPod before making any connections Always wear protective eyewear when using tools INSTALLATION Choosing Installation Locations IMPORTANT Drive Play should be installed according to these instructions and relevant regulations No part of this system should obstruct the driver s view of the road or vehicle controls or information displays necessary for safely operating the vehicle The text display should be positioned to eliminate glare and reflections and should be as close as possible to the driver s normal line of sight Install Text Display on dash on windshield glass on gauges panel on dash behind radio Install Gin glove Se Electronics hox Enclosure under seat Install Control Knob on console Drive Play Components Drive Play consists of three main components Text Display Control Knob and Electronics Enclosure They operate together as a system to make controlling your iPod easy and to route the audio signal to your mobile audio system All three components must be installed You can choose wireless FM transmission wired FM transmission adaptor sold separately or direct con nection of the line output audio signal
17. k of the base 5 Route the attached cable to the Electronics Enclosure Installing the Control Knob NOTE The Control Knob s cable can be routed differently for adhesive or screw mounting The default cable route is through the back of the base and should be used when mounting the base with the supplied adhesive pad For screw mounting the cable can be routed through the center of the base and through a hole that must be drilled in the mounting surface You may use the mounting plate as a template INSTALLATION Place the Control Knob at the site and check the operation angle with the default 30 base If it meets your needs then skip to step 2 Otherwise change the base as follows a Using a Phillips screwdriver remove the two screws from the bottom of the base and set the internal mounting plate aside Control Internal a Mounting y Plate t w While holding the base grasp the Control Knob and turn it to the right until you feel it release from the base Slide the base off the attached cable and put it aside Select another base 0 or 60 and thread the cable through the base to meet the Control Knob Place the new base against the Control Knob bottom and turn it to the left until it locks Route the attached cable through the base s opening Fasten the internal mounting plate to the base with the screw s from step a NOTE The 60 base uses two screws while the 0 base uses one screw
18. onal CD Changer L R In Leer Wired Auxiliary FM Adaptor Device optional Antenna Cable optional i ii 12 Volt disconnect from 12Vdc yellow i Fi 7 Accessory Head Unit Radio Cell Phone Satellite Radio etc ACC red GND black Power Cable Direct Connection of the 12 Volt Power Harness With In Line Fuse Holder Use this method when you want a permanent power connec tion to the vehicle Also by connecting the harness s red wire to the ignition switch s ACC terminal Drive Play will turn on or off with the vehicle s ignition ACC switch An in line fuse holder provides protection for the unit IMPORTANT Replace the in line fuse only with one of the same type and rating INSTALLATION 5 drive Installing Components Installing the Electronics Enclosure At the selected site install the Electronics Enclosure Use either the enclosed cable ties or mounting screws as shown below harman kardon Installing the Text Display 1 Temporarily place the Text Display at the proposed site and check the default viewing angle while adjusting the pivot arm If it meets your needs then skip to step 2 Otherwise change the viewing angle as follows a Using the 3mm hex key loosen the recessed hex screw inside the display base until the pivot arm is free from the display assembly The hex screw will remain captive Recessed Hex Screw 6 INSTALLATION b Select ano
19. resents absolutely no risk before browsing your iPod or adjusting the settings on your Drive Play Connecting the iPod Always hold the Drive Play s iPod dock connector by its sides and gently insert or remove the dock connector Never use excessive force to insert or remove the connector or damage to your iPod may occur Lost Data Harman Kardon is not responsible for any lost data on your iPod when using the Drive Play Be sure to back up the audio data files on your computer Loud Music and Hearing Playing loud music in a vehicle can permanently damage your hearing as well as hinder your ability to hear traffic The max imum volume levels achievable with this product combined with high power amplification may exceed safe levels for extended listening We recommend using low volume levels when driving Harman Kardon accepts no liability for hearing loss bodily injury or property damage as a result of use or misuse of this product Headphones and Driving Do not use headphones while operating a vehicle This practice is illegal in some areas Always be careful and attentive to your vehicle and the traffic around you Always obey all traffic laws while driving Drive Play s audio output is not suitable for driving headphones and is intended to output a signal appro priate for an audio system s line level input jack About Installation Although we recommend professional installation for your Harman Kardon Drive
20. t select Off default One or All OPERATION 11 drive TROUBLESHOOTING Problem Message iPod Disconnected Solution e Check that the iPod Connection Cable is connected between the Electronics Enclosure and the iPod Problem Message AUX is Disabled Solution Check AUX Input see page 10 Check the connection between the Electronics Enclosure and the auxiliary device Problem Hearing static when playing the iPod with wireless FM transmission Solution Interference from an FM station at the same frequency Try another FM frequency see page 9 Consider installing the optional Wired FM Adaptor see page 5 Problem Drive Play won t turn on Solution Replace the in line fuse with one of the same type and rating Problem Message Please update your iPod software Solution Download and install the latest software version for your iPod see Apple com Technical Support If you are having other problems with Drive Play please contact us at 1 516 255 HKHK 4545 Or on the Web at www harmankardon com 12 TROUBLESHOOTING TECHNICAL SPECIFICATIONS Dimensions of Electronics Enclosure 6 152 0mm x 1 1 4 32 4mm x 2 5 8 66 4mm W x H x D Maximum Mounting Diameter of Text Display 113 16 46 2mm Maximum Mounting Diameter of Control Knob 113 16 45 9mm Fuse Rating 2A Nominal Current Requirement with iPod Connected 500mA Line
21. ther viewing angle position middle or top Reassemble the parts in reverse order and tighten the recessed hex screw 3mm Hex Key Display Base Display Assembly At the base using the 1 5mm hex key loosen but do not remove the hex setscrew To install the Text Display with adhesive tape perform the following steps or skip to step 4 a Insert the mounting plate rotate it 180 and tighten the hex setscrew as shown below Hex Setscrew t z Mounting Plate t Adhesive CS Pad b At the proposed site wipe the surface and exposed mounting plate with one of the enclosed alcohol pads Allow both to dry c Remove the protective tape from one side of one of the enclosed adhesive pads and press the pad against the mounting plate d Remove the remaining protective tape and press and hold the Text Display to its site for 5 seconds 4 To install the Text Display with mounting screws perform the following steps _ Hex Setscrew q Arrow Mounting oe Plate a At the proposed site place the mounting plate and rotate it so that the arrow will point toward the hex set screw at the back of the base after it s mounted b Holding the mounting plate in position fasten it to the surface with three enclosed mounting screws c Place the Text Display on the mounting plate 180 from its final position and then rotate it a half turn to the final position Tighten the hex setscrew at the bac
22. ur adjustment or selection you may press the top Menu button to go to the previous menu If no but tons are pressed within 10 seconds the Now Playing screen will appear At this point pressing the Menu button will take you back to the screen of your previous selection Repeated Menu presses will take you back to the Drive Play Menu Initial Setup NOTE Please refer to Drive Play s display screen as you make initial settings Also refer to your iPod User s Guide for operation information Power On 1 With the main volume turned down on your audio sys tem power on your entire mobile audio system and then turn on Drive Play by pressing the bottom Play Pause Button If everything is operating correctly the iPod screen will display the following message OK to disconnect 2 Drive Play s Text Display will show the Harman Kardon splash screen first followed by the Now Playing screen What the Now Playing screen displays next depends on the following conditions OPERATION Drive Play will tell your iPod to play the same selection as when it was last turned off If you plugged your iPod into Drive Play while it was playing Drive Play will tell the iPod to play the current song without interruption However if nothing was playing when your iPod was last turned off or when it was plugged in Drive Play will tell the iPod to begin playing the first song in its Songs database Setting FM Transmission
23. with a pencil and continue with the installation Choosing an Audio Interface Referring to the Wiring Diagram on the next page you can interface the Drive Play s audio output to your mobile audio system in three ways 4 INSTALLATION Wireless FM Transmission This method is the most convenient and requires the least wiring After setup you simply tune your radio to the assigned FM frequency to listen to your iPod Drive Play has a built in FM transmitter and its software provides a choice of five fixed FM frequencies or a tunable frequency for areas where none of the fixed frequency selections are available See Initial Setup on page 9 for details Wired FM Transmission For better quality FM transmission performance consider purchasing our Wired FM Adaptor for direct connection via the Antenna jack on the Electronics Enclosure to your radio s antenna input see Wiring Diagram on the next page NOTE Depending on your vehicle model antenna plug adaptors may be required to connect the Wired FM Adaptor to your radio and antenna Connecting to Audio Out This method provides the best sound quality but involves more wiring After making the connections and setup you will select Auxiliary Input or CD Changer on your audio system to listen to your iPod See Initial Setup on page 9 for details NOTE In order to use the Audio Out your audio system must have an auxiliary input jack or a CD changer input A third party int
24. y Input feature select a mounting site for the electronics enclo sure that provides easy access to the Aux In jack Otherwise you will need to purchase a 3 5mm stereo extension cable for a longer cable run see Wiring Diagram on page 5 iPod Location With this system you can place your iPod in any location that allows you to conveniently connect it to the Drive Play iPod cable Since you don t have to view the iPod or use its controls you can place it inside the center console compartment the glove box or another hidden site NOTE Since an iPod can get hot during operation avoid tightly enclosed areas Review About Operating and Storage Temperatures in your iPod s User s Guide Planning the Installation IMPORTANT When routing wires from any of the compo nents to the electronics enclosure be sure to route them away from any moving parts such as the gear shift levers pedals parking brake and steering column Temporarily place the main components at their proposed sites and lay out their interconnect cables to judge the cable routes see Wiring Diagram on page 5 for wiring options If a cable comes up short try moving one or more components to find a better run Next inspect the vehicle s interior assembly and locate areas where cables can be hidden or tucked into seams e g under the center console housing along body panel etc Once you have found the ideal cable runs and component locations mark the sites
Download Pdf Manuals
Related Search