Harbor Freight Tools Solar Rope Light Product manual
Contents
1. Doar Rops Oht n E Item 68353 1 Verify that installation surface INSTRUCTIONS AND has no hidden utility lines PRECAUTIONS before drilling driving screws or digging to insert stake Important Safety Information Visit our website at http www harborfreight com 2 Place mount the LED Rope to prevent tripping or choking Keep out of reach of young AWARNING children and babies 3 Install only according to these instructions Improper installation can create hazards Read this material before using this product Failure to do so can result in serious injury 4 Wear ANSI approved safety SAVE THIS MANUAL goggles and heavy duty work gloves during installation When unpacking make sure 5 Keep installation area that the product is intact and clean and well lit undamaged 6 Keep bystanders out of the If any parts are missing or broken area during installation please call 1 800 444 3353 as soon as possible 7 Do not install when tired or when under the influence Copyright 2011 by Harbor Freight Tools of drugs or medication All rights reserved No portion of this document or any artwork contained herein may be 8 This product is not a toy reproduced in any shape or form without the Do not allow children to play express written consent of Harbor Freight Tools with or near this item Diagrams within this document may not be drawn l proportionally Due to continuing improvements 9 Use as2. Solar Panel 1 to the slots on the Panel Connector Stake Mounting 1 Select a ground location to insert the Stake 6 Make sure that there are no hidden obstacles or utility lines in the area If the ground is too hard to insert the stake dig a hole large enough for the stake refill the hole and slightly pack the ground to give some support Insert the Stake into the hole Attach the Stake Connector 4 onto the top of the Stake Attach the Panel Connector 2 to the top of the Stake Connector Attach the Solar Panel 1 to the slots on the Panel Connector LED Rope Mounting 1 For technical questions please call 1 800 444 3353 The LED Rope 1 can be left loose or can be mounted to an object Place mount the LED Rope to prevent tripping or choking Keep out of reach of young children and babies If wall mounting select a location without hidden cables or utility lines Also turn off all power in the wall for safety SKU 68353 4 a O gt Drill holes for the Rope Anchors 7c in the desired locations All 8 Rope Clips 7b should be used to reduce the length of loose sections Place the LED Rope through the Rope Clips Insert the Rope Anchors into the holes align the holes in the Clips with the Anchors and secure in place with the Rope Screws 7a Operation Instructions 1 N G9 N Y F S For best results allow light to charge with s
3. intended only actual product may differ slightly from the product described herein Tools required for 10 CONTAINS NICKEL CADMIUM installation and service may not be included BATTERY BATTERY For technical questions or replacement MUST BE RECYCLED OR parts please call 1 800 444 3353 DISPOSED OF PROPERLY Installation Instructions Read the ENTIRE A IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product Selecting a Location 1 Select a mounting location that will receive full sunlight as many hours in the day as possible 2 Even partial shade will greatly hinder charging and therefore limit operation time 3 Ifthe area has strong nighttime light sources these may prevent the light from turning on at night or may cause it to flicker instead of turning on completely Wall Mounting 1 Select a wall location without hidden cables or utility lines Turn off all power in the wall for added safety 2 Place the Wall Base 3 in the desired location and mark through the mounting holes 3 Set the Wall Base aside and drill holes in the marked locations appropriate for the Wall Anchors 5b Page 2 Insert the Wall Anchors into the holes align the holes in the Base with the Anchors and secure it in place with the Wall Screws 5a Attach the Panel Connector 2 to the Wall Base 3 Attach the
4. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Page 3 Parts List and Assembly Diagram Part Description _ Part Description _ 6 Stake S Page 4 For technical questions please call 1 800 444 3353 SKU 68353
5. witch in off position for at least 1 day before switching on Turn the switch underneath Solar Panel 1 to C for the light to illuminate constantly or to B for the light to blink instead Light will turn on at dusk and turn off at dawn Battery Replacement Turn the switch underneath Solar Panel 1 to OFF Remove the four screws under the Solar Panel 1 Open the Solar Panel Remove the old battery and recycle or dispose of it properly CONTAINS NICKEL CADMIUM BATTERY BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY KU 68353 For technical questions please call 1 800 444 3353 5 Install a new battery of same size and type in the Solar Panel 6 Close the Solar Panel and secure with the screws Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER
Download Pdf Manuals
Related Search