Home
Harbor Freight Tools Motorized Rotary Laser Level Kit Product manual
Contents
1. a as Specifications 1 Loosen the Battery Cover Knob 5A and remove the Battery Cover 2A See Figure 1 below NOTE The Knob will NOT come all the way out Battery Cover 4 AA Batteries Battery insert Cover 2A Rotary Laser Level batteries here Instructions for Putting Into Use Read the ENTIRE IMPORTANT A SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Figure 1 2 Install four AA Batteries making sure to follow AWARNING the polarity marked in the Battery Compartment TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION Turn the Power Switch to Off before adjusting Level 3 Replace the Battery Cover and turn Battery Cover Knob until Cover is secured into place Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram on the last page SKU 69247 For technical questions please call 1 800 444 3353 Page 3 Mounting To Tripod 3 1 If mounting the Laser Level with the Tripod 3 position the Tripod on a flat and level ground surface Extend Tripod Legs to the desired height using the Bull s Eye Vial 15 located on the Tripod Head 4 See Figure 2 below Figure 2 Tripod Head 4 Bull s Eye Vial 15 2 Once the Tripod is level lock the legs in place using the clamps on each leg 3 Then thread Wall Bracke
2. PITTSBURGH MOTORIZED ROTARY LASER LEVEL KIT Item 69247 AWARNING Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 800 444 3353 as soon as possible Visit our website at http www harborfreight com Email our technical support at tech harborfreight com Copyright 2011 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference IMPORTANT SAFETY INFORMATION In this manual on the labeling and all other information provided with this product This is the safety alert symbol It is used to alert you to potential persona
3. an interior Operating Instructions PATEE APOR MANON SECHNON al me wall first mark the desired height of the rail beginning of this manual including all text under subheadings therein 2 Align the Laser Level with that point and check to before set up or use of this product make sure the Vial Levels 9A are level with the floor Initial Leveling 3 Shine laser beam on the adjoining wall and have an assistant mark that location 1 When the Laser Level is properly positioned activate the Laser by turning the Power Rotation Control Switch 11A clockwise Then recheck the Level Vials 9A to make sure 5 This technique can be used to install the Laser Level has not been bumped or moved vertical or 45 degree angle objects 4 Then install the chair rail in a direct line between the two points 2 The rotation speed of the Laser Head Cover 6A can be set by adjusting the Rotation Control Switch Checking a Slope Turn clockwise to make the beam rotate faster Turn counterclockwise to slow the beam down 1 For example to determine the slope of a floor place the Laser Level at one end 3 Mark the desired measurement s of the floor using the Tripod 3 Then turn off the Laser Level by turning the Rotation Control Switch counterclockwise all the way Check to make sure the Vial Levels 9A are level 3 Measure the vertical drop from the Equalizing Height Of Laser Lens to the floor surface Distant Objects 4 Shi
4. do not drop or jar the Laser Level If installing on a wall surface without the Tripod 3 verify that installation surface has no hidden utility lines before drilling or driving screws Keep work area clean and well lit This product is not a toy Keep it out of reach of children Keep children and bystanders away while operating Laser Level Inspect before every use do not use if parts are loose or damaged Stay alert watch what you are doing and use common sense when operating Laser Level Do not use Laser Level while you are tired or under the influence of drugs alcohol or medication Dress properly Do not wear loose clothing or jewelry Keep your hair clothing and gloves away from moving parts Maintain labels and nameplates on the tool These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement WARNING The brass components of this product contain lead a chemical known to the State of California to cause birth defects or other reproductive harm California Health amp Safety code 25249 5 et seq The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS SKU 69247
5. e listed and shown for illustration purposes only and are not available individually as replacement parts Parts not shown to scale REV 11d SKU 69247 For technical questions please call 1 800 444 3353 Page LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifi
6. es the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state PITTSBURGH 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
7. l injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death 4A DANGER DANGER indicates a hazardous situation which if not avoided will result in death or serious injury AWARNING WARNING indicates a hazardous situation which if not avoided could result in death or serious injury ACAUTION CAUTION used with the safety alert symbol indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE NOTICE is used to address practices not related to personal injury CAUTION CAUTION without the safety alert symbol is used to address practices not related to personal injury General Safety Warnings WARNING Read all safety warnings and instructions Save all warnings and instructions for future reference 1 Avoid direct eye exposure to laser light Do not direct the laser beam into the eyes of any person or animal Doing so may cause severe eye injury or permanent blindness Page 2 10 Ti 12 13 14 15 For technical questions please call 1 800 444 3353 Verify Laser Level is in the Off position before making any adjustments or changing the batteries Position batteries in proper polarity and do not install batteries of different types charge levels or capacities together Remove batteries if Laser Level is not to be used for a long period of time The Laser Level is a delicate instrument
8. ne the laser beam on a ruler held vertical at the other end of the floor The difference in these 1 For example if you wish to install cement measurements is the amount of slope in the floor footings for a storage shed first determine the desired height of any one of the footings 5 This technique can be used to design slope such as when constructing an outdoor 2 Align the laser beam with the top surface of the surface which will require a runoff slope reference footing and check to make sure the Vial Levels 9A are level with the ground 3 Direct laser beam toward each of remaining footing locations On reference stakes at those locations mark the spot the Laser illuminates This indicates desired top surface of that footing 4 This technique can be used for many similar applications i e to align pictures on a wall SKU 69247 For technical questions please call 1 800 444 3353 Page 5 Maintenance and Servicing Procedures not specifically explained A in this manual must be performed only by a qualified technician AWARNING TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION Turn OFF the Laser Level before performing any inspection maintenance or cleaning procedures TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use Cleaning Maintenance and Lubrication 1 BEFORE EACH USE in
9. spect the general condition of the Laser Level Check for loose hardware misalignment or binding of moving parts cracked or broken parts and any other condition that may affect its safe operation 2 AFTER USE wipe external surfaces of the tool with clean cloth Do not immerse the Laser Level in any liquids 3 Store the Laser Level indoors and out of children s reach Page 6 For technical questions please call 1 800 444 3353 SKU 69247 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUALAS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Parts List and Assembly Diagram Part Description _ Part Description _ 0 Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts ar
10. t 7A onto Tripod Head See Figure 3 below Wall Bracket 7A Height Adjusting Handle 13 Tripod Head 4 Height Locking Knob 14 Figure 3 4 Once the Wall Bracket 7A is secured on the head you can use the Height Adjusting Handle 13 to raise the Level Housing to the desired height Once the desired height is reached lock the height in place by turning the Height Locking Knob 14 See Figure 3 Page 4 For technical questions please call 1 800 444 3353 Mounting To Wall The Laser Level may also be installed on a wall surface without the Tripod To do so use the Wall Bracket 7A to secure the Laser Level to the wall First set the Level Housing against the part of the wall where you wish to install the Laser Level WARNING Verify that installation surface has no hidden utility lines before drilling or driving screws Use a pencil to mark drill holes through the Wall Bracket 7A See Figure 4 below Figure 4 Secure the Laser Level to the wall surface using screws and plastic anchors not included NOTE The mounting screws must be long enough to allow for the Wall Bracket frame to fit over them Once installed on wall level the Laser using the Leveling Knobs 8A located on each side of the Laser and the Level Vials 9A located at the top of the Laser SKU 69247 Installing Horizontal Or Vertical Objects T Read the ENTIRE IMPORTANT 1 For example to install a chair rail on
Download Pdf Manuals
Related Search
Related Contents
80_833_05--DBL-01-de Topaz KTS User Guide (Screen optimized) Disgo Tablet 8000 User's Manual Type Dynamics Indicator - TDI User's Guide Version Table of Contents USB Serial Adapter for MAC OS 8.6 Marantz SR7200 User's Manual AXU 台湾知的財産権関連事例と判決 2009 シ=アー熱風機プラジェット體 Copyright © All rights reserved.
Failed to retrieve file