Harbor Freight Tools Bicycle Lift Product manual
Contents
1. SKU 95803 For technical questions please call 1 800 444 3353 Page 82. up See Figure 1 SKU 95803 For technical questions please call 1 800 444 3353 Page 4 Figure 2 4 Using the Wood Screws 6 provided mount each of the Lift Brackets 1 amp 2 to either the joists or the Mounting Board See Figure 2 5 Ensure that the Hook Pulleys 3A amp 3B line up with your Handlebar Seat measure ments See Figure 1 NOTE If you are planning to mount the Lift Brackets 1 amp 2 across the joists instead of parallel with them you will need to use a Mounting Board as seen in Figure 1 Figure 3 6 Push one end of the Nylon Rope 5 up through the square hole on the Rear Lift Bracket 1 and tie a double knot Thread the Rope down through the Rear Hook Pulley 3A then up through the Pulley on the Rear Lift Bracket 1A Lead the Rope through the rear pulley of the Front Lift Bracket 2 and then down through the Front Hook Pulley 3B Finish by taking the Rope up through the Pulley of the Front Lift Bracket 2A The remainder of the Rope 5 will now hang free and be used to raise and lower your bike Excess Rope will be tied off at the Rope Cleat 4 See Figure 3 SKU 95803 For technical questions please call 1 800 444 3353 Page 5 Using the final two Wood Screws 6 attach the Rope Cleat 4 to a stud or other secure surface located on the side wall If no stud is available you can use wall anchors not included Do not cut the Rope 5 Use the Rope Cleat to wrap the excess See Figure 4
3. BICYCLE LIFT WM Kexe 1 95803 ASSEMBLY AND OPERATION INSTRUCTIONS NOTE 46 Nylon Rope and Mounting Hardware included but not shown Due to continuing improvements actual product may differ slightly from the product described herein Distributed Exclusively by pig HARBOR FREIGHT lt ins TOOLS Wms 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2007 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 SPECIFICATIONS Construction material 18 gauge steel plate with steel Bike capacity One brackets Weight of Lift 3 4 Ib Nylon Rope length 46 Overall dimensions 4 L X 3 1 2 W X 1 H May vary due to size of Weight Capacity 44 Ib Bike being stored Front Lift Bracket size 10 L Hook Pulley size 2 2 1 4 L X 3 7 16 W X 3 1 4 H X 3 W X 9 1 4 H Rear Lift Bracket size Mounting Fasteners 10 10 L X 3 7 16 W X 3 1 8 H Phillips Head Screws Save This Manual You will need this manual for the safety warnings and precautions assembly oper ating inspection maintenance and clean
4. OPERATION INSTRUCTIONS RAISING THE BIKE FOR STORAGE Before first use test the Bicycle Lift by using small sandbags or similar items that weigh no more than 50 Ib and are evenly distributed between the front and back pulleys This will show if the Bicycle Lift is installed properly Lower Front and Rear Hook Pulleys 3A amp 3B as evenly as possible and to a height where you can comfortably lift the Handlebars and Seat onto the Front and Rear Hook Pulleys 3B amp 3A Tie off the Rope 5 on the Rope Cleat 4 to prevent slip page of the Pulleys as you lift the Bike onto the Hook Pulleys Once the Handlebars and Seat are securely hanging on their respective Hook Pul leys unfasten the Rope 5 from the Rope Cleat 4 and slowly and evenly pull the Bicycle to the height needed Anytime you release pressure on the Rope you will engage the Rope Lock located on the Front Lift Bracket 2 and the Bike will stay where it is suspended at the time After you have raised the Bicycle to the height you where you want it to be wrap the Rope 5 around the Rope Cleat 4 using a figure eight motion NEVER cut off excess rope SKU 95803 For technical questions please call 1 800 444 3353 Page 6 REMOVING THE BIKE FROM STORAGE L Unwrap the Rope 5 from the Rope Cleat 4 Even though the Bike should be held secure by the Rope Lock to prevent it from falling hang on to the Rope 5 securely as an added safety precaution 2 While maintaining
5. ing procedures parts list and assembly diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Write the products serial number in the back of the manual near the assembly diagram or write month and year of purchase if product has no serial number Keep this manual and invoice in a safe and dry place for future reference GENERAL SAFETY RULES WARNING READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock fire and or serious injury SAVE THESE INSTRUCTIONS WORK AREA 1 Keep your work area clean and well lit Cluttered benches and dark areas invite accidents 2 Always wear ANSl approved safety goggles when assembling and installing the Bicycle Lift 3 If using a power drill not included while installing be sure to follow all warn ings and instructions provided in the manual of the tool you are using SKU 95803 For technical questions please call 1 800 444 3353 Page 2 Do not store more than one bicycle at a time on the Bicycle Lift Do not exceed the weight bearing capacity of the surface this Bicycle Lift is attached to The surface must be able to support the 3 4 Ib weight of the Bike Lift as well as the weight of the bicycle which should not exceed 50 Ib Make sure the lift brackets are securely fastened during installation Harbor Freight Tools cannot be responsible for damage to your Bicycle or personal inj
6. issing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible SKU 95803 For technical questions please call 1 800 444 3353 Page 3 ASSEMBLY INSTRUCTIONS NOTE For additional information regarding the parts listed in the following pages refer to the Assembly Diagram on page 8 NOTE Tools required Phillips Head Screwdriver not included or Power Drill Screwdriver not included Figure 1 Mounting Board 1 For best results mount the Lift Brackets 1 amp 2 so the Hook Pulleys 3A amp 3B are directly above the Bicycle s seat and handlebar See Figure 1 NOTE If you wish you may attach the entire assembly to a Mounting Board not included then mount the board to the ceiling joists See Figure 1 2 Measure the distance between the handlebars and the back of the seat This is where the Hook Pulleys 3A amp 3B will be attached to the bike See Figure 1 3 Use a stud finder not included to locate a ceiling joist If your ceiling is covered with drywall look for nails irregularities or attached fixtures These are clues to lo cating joists Use a small nail not included or a screwdriver not included to run a pilot hole into the ceiling to insure you have located a joist Once a joist is located measure from the sidewall to the joist Transfer your seat handlebar measurement along the length of the joist so Front and Rear Lift Brackets 1 amp 2 will line
7. n strands If any damage is pulleys found Immediately replace the 3 Pulleys may need some lubricating neg DO NOT try to repair with ape Lubricate Pulleys with a drop or two of light oil not included SKU 95803 For technical questions please call 1 800 444 3353 Page 7 PARTS LIST Part Description Q ty Part Description Q ty 6 Wood Screws 10 a eens eee ASSEMBLY DIAGRAM Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEM BLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUY ER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO
8. tension on the Rope 5 pull it towards the Rear Lift Bracket 3A This will release the Rope Lock and the Bike can then be lowered slowly to a height where it is comfortable for you to lift the Handlebars and Seat away from their re spective Hook Pulleys Before removing the Bike from the Hook Pulleys secure the Rope 5 around the Rope Cleat 4 fo prevent the Bike from suddenly dropping 3 After removing the Bicycle from the Bike Lift raise the Hook Pulleys 3A amp 3B to a height where they will not be at risk to anyone walking beneath them Tie off the excess Rope 5 by wrapping it around the Rope Cleat 4 INSPECTION MAINTENANCE AND CLEANING 1 BEFORE EACH USE inspect the general condition of the tool Check for loose screws misalignment or binding of moving parts cracked or broken parts damage or frayed strands on the Rope 5 and any other condition that may affect its safe operation If anything abnormal should occur have the problem corrected before further use Do not use damaged equipment MAINTENANCE CHART Before Every 6 Maintenance Type eee e Weekly Monthly Months Inspect tool for damage Wipe off with clean moist enseres o xo o d TROUBLESHOOTING Rope 5 binds or will 1 Rope has somehow slipped off of a 1 Check Rope 5 make sure it is on not pull smoothly pulley each pulley 2 Rope is frayed and broken strands 2 Check the Rope 5 for fraying or are imbedded around one of the broke
9. ury if this Bicycle Lift is not properly installed NEVER allow children to play with or use this Bicycle Lift Maintain labels and nameplates on the tool These carry important information If unreadable or missing contact Harbor Freight Tools for a replacement When lowering a Bicycle do not let children or anyone else stand directly underneath the Bicycle Lift Maintain a safe working environment Make sure there is adequate surrounding workspace Do not use this product in a damp or wet location Do not use the Bicycle Lift to support anything except a bicycle Do not let people or animals hang from the Bicycle Lift Regularly check all pulleys and brackets for tightness Do not use Bicycle Lift if the rope begins to fray or if any part is chipped or broken After installing and before first use test the Bicycle Lift by using small sand bags or similar items that weigh no more than 50 Ib and are evenly distributed between the front and back pulleys This will show if the Bicycle Lift is installed properly before a bicycle is stored on the unit The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator UNPACKING When unpacking check to make sure that the item is intact and undamaged If any parts are m
Download Pdf Manuals
Related Search