Harbor Freight Tools 99621 User's Manual
Contents
1. Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates 4 DANGER a hazardous situation which if not avoided will result in death or serious injury AWARNING WARNING indicates a hazardous situation which if not avoided could result in death or serious injury with the safety alert symbol indicates a hazardous situation which if not avoided could result in minor or moderate injury SKU 99621 For technical questions please call 1 800 444 3353 NOTICE is used to NOTICE address practices not related to personal injury CAUTION without CAUTION the safety alert symbol is used to address practices not related to personal injury READALL INSTRUCTIONS Personal Safety CAUTION To prevent injury 1 Read ATV mower manual before installation 2 Wear ANSI approved safety goggles and heavy duty work gloves during installation and use Use of face or dust mask is recommended if opera tion is dusty 3 Keep clear of Turning Plate 16 dur ing use 4 Keep out of reach of children 5 Secure Spreader attachment before use 6 Replace fuse only with same type and rating 7 Use for intended purposes only Do not use for hauling 8 Dress Properly Do not wear loose clothing or jewelry They can be caught in moving parts Wear protec tive hair covering to contain long hair Page 2 9 Wear thick jeans and steel toed work boots t2. Rail 21 to the Hopper Assembly 8 using Screws M5 x 35 14 3 Position the Gauge Assembly 22 to either Frame Rail 21 based on whether the Hopper Assembly 8 is to be mounted on the front or rear rack of the ATV If mounted on the rear rack the Control Handle 25 should be on the right Frame Rail 21 If mounted on the front rack place the Control Handle 25 on the Left Frame Rail 21 See Figure 1 below Turning Plate 16 f er aaa Moret 1 Adjustment Plate 13 Handle 25 Gauge Assembly 22 Figure 1 Switch Box Installation WARNING To prevent serious injury make sure the ATV is OFF before install ing The Switch Box Assembly 31 1 Attach the Switch Box Assembly 31 to your ATV Route cable ties through the two slots located on the Switch Box Assembly 31 and connect them onto the ATV Frame NOTE Make sure the Switch Box As sembly 31 is secure before proceeding 2 Connect the ATV Battery Terminals 31 3 to battery Connect the white wire to the battery s positive pole connect the black wire to the battery s negative pole 3 Connect the Motor Terminal 31 4 to the Electric Motor 3 terminal 4 Connect the ATV Battery Terminals 31 3 to the Motor Assembly using the Harness Connector See parts list and assembly diagram page 7 and 8 REV 08g 09a SKU 99621 For technical questions please call 1 800 444 3353 Page 4 SKU 99621 How to Attach to your ATV
3. Place the ATV Spreader assembled centered on the front or rear luggage rack of your ATV Use the J Bolts 34 Press Plate 33 and Hex Nuts 32 to connect Frame Rail 21 to the luggage rack cross bar closest to the seat or handlebars Use the J Bolts 34 Press Plate 33 and Hex Nuts 32 to attach the Spreader to the luggage rack securing it to the outer most rail on the luggage rack WARNING Prior to each use inspect the mounting hardware and the ATV Spreader to ensure the tightness of the mount If any hardware is loose tighten securely before using the unit Functions This ATV Spreader can be used to spread grass seed fertilizer pellets sand ice melt and any other type of seed or loose pellet type lawn care products NOTE Not for powdered lawn prod ucts which are hard to adjust spread rates or for heavy mulch type prod ucts which will clog the Turning Plate 16 OPERATING INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product A Before operating the ATV Spreader put on ANSI approved safety goggles and other safety gear not supplied 2 For technical questions please call 1 800 444 3353 An Adjustable Solid Stop is provided to allow the operator to adjust the Gauge Assembly 22 to the desired opening allowing the correct amount of material to fall ont
4. load capacity of the vehicle to be loaded Be sure to account for the weight of this Spreader and the weight of the material being spread 6 Maintain labels and nameplates on the appliance These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement 7 The warnings precautions and in structions discussed in this instruction manual cannot cover all possible con ditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS SPECIFICATIONS 80 LB Weight capacity 1900 cu in Storage capacity Hopper Assembly alai 12V Electric Page 3 UNPACKING When unpacking check to make sure that the item is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible SET UP INSTRUCTIONS SAFETY INSTRUCTIONS section at the beginning of this manual including all text under subheadings therein before set up or use of this product f Read the ENTIRE IMPORTANT Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near the end of this manual Assembly 1 The ATV Spreader comes partially assembled 2 Mount the two sides of the Frame
5. 12 VOLT 80 LB ATV SPREADER SET UP AND OPERATING INSTRUCTIONS 4 Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2008 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included For technical questions or replacement parts please call 1 800 444 3353 SAVE THIS MANUAL Keep this manual for the safety warn ings and precautions assembly operat ing inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference IMPORTANT SAFETY INSTRUCTIONS In this manual on the labeling and all other information provided with this product This is the safety alert symbol It is used to alert you to potential personal injury hazards
6. erAssembly 1 27 _ Wood Screw m4 5X18 2 9 FlatWasher_ 4 28 AdjustmentWire H 17 Wood Screw m4 5x10 3 32 HexNutme 19 Philips Screws mex45 j1 34 J Bot l8 Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not avail able individually as replacement parts REV 08g SKU 99621 For technical questions please call 1 800 444 3353 Page 7 ASSEMBLY DIAGRAM REV 08g Page 8 For technical questions please call 1 800 444 3353 SKU 99621
7. fter use Clean then store indoors out of children s reach MAINTENANCE AND SERVICING Procedures not specifically explained in this manual must be performed only by a qualified technician TO PREVENT AWARNING SERIOUS INJURY FROM ACCIDENTAL OPERATION Turn the Power Switch of the vehicle to its OFF position before performing any inspection maintenance or cleaning procedures TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use Cleaning Maintenance and Lubrication 1 BEFORE EACH USE inspect the general condition of the ATV Spread SKU 99621 For technical questions please call 1 800 444 3353 er Check for loose screws misalign ment or binding of moving parts cracked or broken parts damaged electrical wiring and any other condi tion that may affect its safe operation 2 AFTER USE clean external surfaces with clean moist cloth 3 Clean out the Hopper Assembly and using a shop vacuum not supplied clear all leftover material from the Turning Plate 16 and other areas of the Spreader 4 Rinse the ATV Spreader with a hose and fresh clear water Let dry before storing indoors away from children 5 NOTE If the ATV Spreader is to be left outside between jobs always cover with the Rain Cover 1 to protect both the Spreader and any material that may be in the Hopper A
8. o help prevent injury caused by flying debris 10 Stay alert Watch what you are doing Use common sense Do not operate ATV Spreader when you are tired 11 Do not grasp the exposed Turning Plate 16 edges when picking up or hold ing the Spreader 12 Do not Use In Rain or damp loca tions 13 All visitors should be kept at a dis tance from work area 14 When servicing use only identical replacement parts 15 Store Idle ATV Spreader Indoors out of reach of children 16 Maintain ATV Spreader With Care Follow instructions for lubrication Check for damaged parts If anything irregular is found the damage should be properly repaired by a qualified technician unless indicated else where in this manual 17 Disconnect the ATV Spreader when not in use and or before servicing Specific Safety Rules 1 Care must be taken when lifting this ATV Spreader so as not to cause equipment damage and or personal injury 2 Remove any material in Hopper As sembly 8 before removing this ATV Spreader from the vehicle SKU 99621 For technical questions please call 1 800 444 3353 3 Never attempt to install this ATV Spreader to the ATV vehicle alone Have another adult assist when at taching or detaching 4 Refer to the material packaging or bag safety instructions when handling all materials to be applied with this Spreader 5 Before attaching this ATV Spreader consideration must be given to the
9. o the Turning Plate 16 for disbursement The Solid Stop will allow the operator to repeat the opening closing without having to look at the control while op erating the vehicle It is set by using the Thumb Wing Nut 24 located on the Gauge Assembly 22 Establish the correct opening then lock down the Thumb Wing Nut 24 Measure off a distance of 50 feet on the surface you will be working See number 9 below Weight out enough of the material to fill the Hopper Assembly 8 at least half full Record the weight for further use Set the Adjustable Solid Stop on the Gauge Assembly 22 to the desired opening and tighten the Thumb Wing Nut 24 NOTE Usually an approximate spreading rate is listed in material di rections or on the bag of the specific material you will use As you start driving the ATV through the work area open the Control Handle 25 till it stops against the Adjustable Solid Stop Continue to spread the material till you cross the end of the area you are working Close the Control Handle 25 to stop the flow of material onto the Turning Plate 16 Page 5 9 Empty the Hopper Assembly and re weigh the material By taking note of how much material you used and how wide the spreading area was you can figure the correct rate of spread This will help you maintain the correct spreading rate for your project 10 To prevent accidents turn off the ATV and disconnect the ATV Spreader a
10. ssembly 8 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Page 6 Troubleshooting Possible Causes Likely Solutions Control Handle will 1 Material clogging port of Gauge 1 Check both Gauge Assembly 22 not open close Gauge Assembly 22 and or Adjustment and Adjustment Plate 13 and clear Assembly Plate 13 debris if necessary Material not spreading 1 Wrong opening on Gauge Assembly 1 Loosen Thumb Wing Nut 24 and at proper rate 22 open close accordingly and re adjust if necessary appliance Turn off ATV and remove Spreader from vehicle before t Follow all safety precautions whenever diagnosing or servicing the service PARTS LIST 6 UnlockNut f2 25 ControlHandle 8 Hopp
Download Pdf Manuals
Related Search