Harbor Freight Tools 98059 User's Manual
Contents
1. Adapter Keep the Cord away from heat oil sharp edges or moving parts Damaged or entangled Cords increase the risk of electric shock e When operating the Scale outdoors use an extension cord suitable for outdoor Page 2 use Use of a cord suitable for outdoor use reduces the risk of electric shock f If operating the Scale in a damp location is unavoidable use a Ground Fault Circuit Interrupter GFCI protected supply Use of a GFCI reduces the risk of electric shock Personal safety a Stay alert watch what you are doing and use common sense when operating the Scale Do not use the Scale while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating the Scale may result in serious personal injury b Use safety equipment Always wear eye protection Safety equipment such as ANSI approved safety impact goggles will reduce personal injuries c Prevent unintentional starting Ensure the Power Switch 11 is in the off position before connecting to power source and or battery pack picking up or carrying the tool Carrying battery operated equipment with your finger on the Power Switch or energizing equipment that have the Power Switch on invites accidents d Do not overreach Keep proper footing and balance at all times This enables better control of the Scale in unexpected situations Scale use and care a Do not force the Scale Use the correct Scale for2. 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Electrical Requirements Maximum Weight Capacity Minimum Weight Control Panel Button Indicators Red LED Indicators Additional Features Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference Important Safety Information In this manual on the labeling and all other information provided with this product This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates a hazardous situation which if not avoided will result in death or serious injury AWARNING WARNING indicates a hazardous situation which if not avoided could result in death or serious injury SKU 98059 For technical questions please call 1 800 444 3353 CAUTION used with the safety alert symbol indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE NOTICE is used to add
3. ANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 98059 For technical questions please call 1 800 444 3353 Page 9 Parts List amp Assembly Diagram ay 14 Bolt M3 x 16 Part Description Qty Bolt M6 x 25 6 seme feom oa 4 9 Bottom Housing 1 Foot 14 15 Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 98059 For technical questions please call 1 800 444 3353 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and
4. LENGTH AMPERES at full load Based on limiting the line TABLE A voltage drop to five volts at 150 of the rated amperes Volts Alternating Current no xooodimilni Mere Revolutions per Minute SKU 98059 For technical questions please call 1 800 444 3353 Page 5 Read the ENTIRE IMPORTANT SAFETY A INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product TO PREVENT SERIOUS AWARN INJURY FROM ACCIDENTAL OPERATION Turn off and unplug the unit before performing any inspection maintenance or cleaning procedures Scale Set Up 1 Always place the Scale on a clean dry flat level workbench capable of supporting the weight of the Scale and all objects to be weighed 2 The workbench area must be free of vibration strong air currents direct sunshine and high temperatures 9 To level the scale before use d Turn the scale upside down e Rotate the Leveling Feet 15 clockwise until they are fully recessed Then turn counterclockwise three full turns Hold each foot and rotate the locking nut two full clockwise turns or until the locking nut is not tightened on the foot f Turn the scale right side up and place on the work surface Use the built in leveling bubble at the front left hand side of the Scale to check if the scale is level Rotate the feet individually until the leveling bubbl
5. PITTSBURGH Bench Top Digital Scale Item 98059 33 LB Weight Capacity AWARNING Read this material before using this product Failure to do so can result in serious injury Not legal for trade or postage SAVE THIS MANUAL When unpacking make sure that the product is intact and undamaged any parts are missing or broken please 1 800 444 3353 as soon as possible Visit our website at http www harborfreight com Copyright 2008 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Manual Revised 11d ACAUTION Input 120 VAC 60 Hz Output 9 VDC 500mA Battery Type 6V4ah 20HR Battery Charge Time 8 10 Hours Adapter Plug 2 Prong Grounded Power Switch ON Off Rocker Switch 33 Pounds 15 Kilograms 7 ounces 200 grams Yellow Push Button Lb or Kg Blue Push Button Tare Blue Push Button Zero T Tare Z Zero LB Pound KG Kilogram AC AC Powered Four Plastic Feet for Leveling of Scale m This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions
6. ale 2 BATTERY REPLACEMENT A Battery that fails to accept a charge is an indication the Battery should be replaced To replace the Battery requires the use of a soldering tool and specific soldering expertise It is recommended that only a qualified service technician perform a Battery replacement procedure Note Battery must be fully discharged prior to any soldering d AFTER USE clean all external surfaces of the Scale with a soft clean cloth Do not use solvents Do not immerse the Scale in liquid 4 Awarninc If the Cord of the AC DC Adapter is damaged it must be replaced only by a qualified service technician SKU 98059 For technical questions please call 1 800 444 3353 Page 8 Troubleshooting DSPLAY meane ACTIONTO BETAKEN A long period display The ZERO position is Work area too windy or too damp Move Scale to Mid horizontal line unstable a calm dry work area The ZERO position is too high Have a qualified service technician service Scale Upper horizontal line Lower horizontal line The ZERO position is too low Have a qualified service technician service Scale LO Alarm sound Voltage is lower than 4 8 0 1V Recharge or change Battery OL Overoad Immediately remove object s being weighed Do Alarm sound i not exceed 33 LB maximum weight capacity Ng Circuit integrator faulty Have a qualified service technician service Scale Alarm sound PLEASE READ THE FOLLOWING CAREFULLY THE M
7. e is centered 9 When the scale is level secure each foot in place by turning its locking nut counterclockwise until tight Re check the level and re adjust the feet if necessary The scale is now set for operation 8 Check that the Scale s Platform 1 will not come in contact with any object before or during the weighing process 9 Route the AC DC Adapter 25 Cord along a safe route to reach the workbench area without creating a tripping hazard or exposing the Cord to possible damage SKU 98059 FIGURE A BOTTOM VIEW ADAPTER CORD POWER SWITCH 11 k LEVELING FOOT 15 To charge the Battery 21 of the Scale insert the AC DC Adapter 25 Cord into the Charging Input Port located on the underside of the Scale Make sure the Power Switch 11 is in its OFF position throughout the charging process Plug the AC DC Adapter into the nearest 120 volt grounded electrical outlet IMPORTANT The charge time for the Battery is 8 to 10 hours Do not overcharge the Battery to avoid damage to the Battery and or AC DC Adapter When finished charging unplug the AC DC Adapter from its electrical outlet Then unplug the Cord from the Charging Input Port of the unit For technical questions please call 1 800 444 3353 Page 6 Operating the Scale Components and Controls FIGURE B TARE KILOGRAMS UNIT ZERO SCALE LEVEL TARE 26 WEIGHT WINDOW Refer to the above photos f
8. f returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state SKU 98059 For technical questions please call 1 800 444 3353 Page 11 PITTSBURGH 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
9. her Battery Pack b Use this Scale only with specifically designated Batteries Use of any other Battery may create a risk of injury and fire c When the Battery 21 is not in use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the Battery Terminals together may cause burns or a fire d Under abusive conditions liquid may be ejected from the Battery 21 If contact with liquid from the battery accidentally occurs flush with water If liquid contacts eyes additionally seek medical help Liquid ejected from the Battery may cause irritation or burns Service a Have your Scale serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the equipment is maintained Specific Safety Warnings 1 For technical questions please call 1 800 444 3353 Maintain labels and nameplates on the tool These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement This Scale contains a sealed lead Battery Do not dispose of an old Battery in fire to avoid explosion and possible personal injury Recycle old batteries according to local solid waste authority procedures Do not exceed the Scale s maximum weight capacity of 33 pounds Avoid unintentional starting Prepare to begin work before turn
10. hnical questions please call 1 800 444 3353 Grounded tools require a three wire extension cord Double Insulated tools can use either a two or three wire extension cord As the distance from the supply outlet increases you must use a heavier gauge extension cord Using extension cords with inadequately sized wire causes a serious drop in voltage resulting in loss of power and possible tool damage The smaller the gauge number of the wire the greater the capacity of the cord For example a 14 gauge cord can carry a higher current than a 16 gauge cord See Table A Page 4 3 When using more than one extension cord to make up the total length make sure each cord contains at least the minimum wire size required See Table A 4 If you are using one extension cord for more than one tool add the nameplate amperes and use the sum to determine the required minimum cord size See Table A 5 If you are using an extension cord outdoors make sure it is marked with the suffix W A W in Canada to indicate it is acceptable for outdoor use 6 Make sure the extension cord is properly wired and in good electrical condition Always replace a damaged extension cord or have it repaired by a qualified electrician before using it T Protect the extension cords from sharp objects excessive heat and damp or wet areas RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS 120 240 VOLT EXTENSION CORD NAMEPLATE
11. ing on the Scale Do not leave the Scale unattended when it s AC DC Adapter is plugged into an electrical outlet Turn off the equipment and unplug the AC DC Adapter from its electrical outlet before leaving The AC DC Adapter gets hot during use The Adapter s heat can build up to unsafe levels and create a fire hazard if it does not receive adequate ventilation due to an electrical fault or if it is used in a hot environment Do not place the Adapter on a flammable surface Especially avoid placing the Adapter on carpets and rugs they are not only flammable but they Page 3 SKU 98059 also obstruct air flow under the Adapter Place the Adapter on a stable solid nonflammable surface such as a stable metal workbench or concrete floor at least 1 foot away from all flammable objects such as drapes or walls Keep a fire extinguisher and a smoke detector in the area Frequently monitor the Adapter and Battery during use This product is not a toy Keep it out of reach of children People with pacemakers should consult their physician s before use Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure In addition people with pacemakers should Avoid operating alone Properly maintain and inspect to avoid electrical shock Any power cord must be properly grounded Ground Fault Circuit Interrupter GFCI should also be implemented it prevents sus
12. or the following instructions The function buttons Tare Unit and Zero are on the right side of the front of the Scale The indicator lights on either side of the Weight Window display information about the Scale s settings Turning on the Scale Turn the Power Switch 11 to its ON position The Scale will do a self check during which you can determine whether the Weight Window and Zero functions are working normally Reset Weight to Zero 1 The ZERO Indicator Light is located at the bottom left of the Weight Window See Figure B Once the Scale is turned on it will illuminate to indicate the Scale is at the ZERO position 2 If the Weight Window does not display 0 000 before you weigh an object and the zero range is less than 60g press the ZERO key Begin weighing when the Weight Window displays 0 000 SKU 98059 For technical questions please call 1 800 444 3353 Change Units of Measure 1 Press the UNIT button to switch between the measurement unit settings The Kg Kilogram and LB Pound indicator lights are located to the right of the Weight Window indicate which setting is current Set Container to Zero before Weighing The Tare button is used to reset the scale to zero when an empty container is set on the scale and the container is not included in the weight of the objects to be weighed Ti The TARE Indicator Light is located at the top left of the Weight Wind
13. ow See Figure B Once the Scale is turned on it will illuminate to indicate the TARE weight is cleared 2 To weigh objects in a container but not include the container weight place an empty container on the Platform 1 of the Scale Press the TARE button and wait for the Weight Window to display 0 000 indicating the Scale is ready for weighing Place the objects into the container and the Weight Window will display the weight of the objects Turning off the Scale 1 To turn off the Scale simply turn the Power Switch 11 to its position 2 Always make sure to store the Scale in a clean dry safe location out of reach of children and other unauthorized persons Note Disconnect charger Do not store the scale with anything on top of it Page 7 Maintenance Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION AWARNING Turn the Power Switch of the Scale to its OFF position and unplug the unit s AC DC Adapter from its electrical outlet before performing any inspection maintenance or cleaning procedures TO PREVENT SERIOUS INJURY FROM EQUIPMENT FAILURE Do not use damaged equipment If abnormal noise or erratic values are shown have the problem corrected before further use Inspection Maintenance and Cleaning 1 BEFORE EACH USE inspect the general condition of the Sc
14. ress practices not related to personal injury CAUTION CAUTION without the safety alert symbol is used to address practices not related to personal injury General Power Tool Safety Warnings WARNING Read all safety warnings and A instructions Failure to follow the warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference The term Scale in the warnings refers to your battery operated cordless Bench Top Digital Scale 1 Work area safety a Keep work area clean and well lit Cluttered or dark areas invite accidents b Do not operate the Scale in explosive atmospheres such as in the presence of flammable liquids gases or dust Battery operated equipment create sparks which may ignite the dust or fumes 2 Electrical safety a The AC DC Adapter plug must match the outlet Never modify the plug in any way Do not use any additional adapter plugs with the Scale Unmodified plugs and matching outlets will reduce risk of electric shock b Avoid body contact with grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is grounded c Do not expose the Scale to rain or wet conditions Water entering the Scale will increase the risk of electric shock d Do not abuse the AC DC Adapter Cord Never use the Cord for carrying pulling or unplugging the AC DC
15. tained electrical shock The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS AWARNING TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded Do not modify the Adapter Cord Plug provided with the tool Never remove the grounding prong from the Plug Do not use the Adapter if the Cord or Plug is damaged If damaged have it repaired by a service facility before use If the Plug will not fit the outlet have a proper outlet installed by a qualified electrician Double Insulated Tools Tools with Two Prong Plugs S S Outlets for 2 Prong Plug Tools marked Double Insulated do not require grounding They have a special double insulation System which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories Inc the Canadian Standard Association and the National Electrical Code See Outlets for 2 Prong Plug Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration See Outlets for 2 Prong Plug Extension Cords 1 For tec
16. warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost o
17. your application The correct Scale will do the job better and safer at the rate for which it was designed b Do not use the Scale if the Power Switch 11 does not turn it on and off Any equipment that cannot be controlled with the Power Switch is dangerous and must be repaired c Disconnect the AC DC Adapter Cord before making any adjustments changing accessories or storing the Scale Such preventive safety measures reduce the risk of starting the equipment accidentally d Store idle battery powered equipment out of the reach of children and do not allow persons unfamiliar with the Scale or these instructions to operate the equipment Battery powered equipment are dangerous in the hands of untrained users Maintain the Scale Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the Scale s operation If damaged have the Scale repaired before use Many accidents are caused by poorly maintained battery operated power equipment f Use the Scale in accordance with these instructions taking into account the working conditions and the work to be performed Use SKU 98059 of the Scale for operations different from those intended could result in a hazardous situation Battery tool use and care a Recharge only with the AC DC Adapter 25 specified by the manufacturer An Adapter that is suitable for one type of Battery may create a risk of fire when used with anot
Download Pdf Manuals
Related Search