Harbor Freight Tools 95641 User's Manual
Contents
1. be used in either of the 120 volt outlets shown in the preceding illustration See Outlets for 2 Prong Plug EXTENSION CORDS 1 Grounded tools require a three wire extension cord Double Insulated tools can use either a two or three wire extension cord 2 As the distance from the supply outlet increases you must use a heavier gauge extension cord Using extension cords with inadequately sized wire causes a seri ous drop in voltage resulting in loss of power and possible tool damage See Table A 3 When using more than one extension cord to make up the total length make sure each cord contains at least the minimum wire size required See Table A 4 Ifyou are using an extension cord outdoors make sure it is marked with the suffix W A W in Canada to indicate it is acceptable for outdoor use 5 Make sure your extension cord is properly wired and in good electrical condition Always replace a damaged extension cord or have it repaired by a qualified electri cian before using it RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS 120 OR 240 VOLT NAMEPLATE EXTENSION CORD LENGTH AMPERES awe 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 20 8 8 ee ee E E E sso e e e 2 Coo e u 2 0 no a f e a t o T ea ef 0 SKU 95641 For technical questions please call 1 800 444 3353 Page 7 Symbology Double Insulated G p Canadian Standards Association Unde2. ATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO 07g SKU 95641 For technical questions please call 1 800 444 3353 Page 15 ASSEMBLY DIAGRAM Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not avail able individually as replacement parts sig SKU 95641 For technical questions please call 1 800 444 3353 Page 16 INTERIOR OF CABIN LAYOUT SKU 95641 For technical questions please call 1 800 444 3353 Page 17
3. Battery Pack 16 is properly connected to the Electronic Speed Controller 18 Refer to Figure 2 R C Electric Racing One or possibly both of the Propellers Turn off all power and check both Boat will not steer 4A and 4B are damaged or possibly Propellers 4A and 4B for damage or straight or follow fouled with debris fouling and if necessary replace one turning commands or both correctly REV 07f SKU 95641 For technical questions please call 1 800 444 3353 Page 13 Possible Causes Probable Solutions R C Electric Racing 1 Low Transmitter Batteries 1 Change the old 8 AA Batteries in Boat moves or Transmitter 20 for new ones turns without any 2 Someone else is operating a Radio 2 Change frequency crystals on your commands from your Controlled device in the area Transmitter 20 and boat transmitter SKU 95641 For technical questions please call 1 800 444 3353 Page 14 PARTS LIST Part Description y Part Description ay e MotorRetainer a PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEM BLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY ST
4. RADIO CONTROLLED ELECTRIC RACING BOAT ASSEMBLY AND OPERATION INSTRUCTIONS Due to continuing improvements actual product may differ slightly from the product described herein Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDER STAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 Manual Revised 08e SPECIFICATIONS Boat Battery 7 2 V 1800 mAh NiMH Transmitter Batteries Required 8 AA batteries sold separately 26 995 MHz 27 045 MHz 27 095 MHz 27 125 MHz 27 145 MHz 27 175 MHz Control Range up to 400 10 20 minutes per full charge Save This Manual Radio Control Frequencies You will need this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures parts list and assembly diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Write the product s serial number in the back of the manual near the assembly diagram or write month and year of purchase if product has no serial num
5. ber Keep this manual and invoice in a safe and dry place for future reference GENERAL SAFETY RULES AWARNING READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock fire and or serious injury SAVE THESE INSTRUCTIONS WORK AREA 1 Keep your work area clean and well lit Cluttered benches and dark areas invite accidents 2 Do not operate R C Electric Racing Boat in explosive atmospheres such as in the presence of flammable liquids gases or dust Radio Control electronics may create sparks which may ignite the dust or fumes 3 Keep bystanders and visitors away while operating Distractions can cause you to lose control Protect others in the area from rapidly spinning propellers Provide barriers or shields as needed ELECTRICAL SAFETY 1 Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances Never remove the SKU 95641 For technical questions please call 1 800 444 3353 Page 2 grounding prong or modify the plug in any way Do not use any adapter plugs Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded If the tools should electrically malfunction or break down grounding provides a low resistance path to carry electricity away from the user Double insulated tools are equipped with a polarized plug one blade is wider than the other This pl
6. d operating procedures before being allowed to use this product and must always be supervised by a responsible adult Never leave the R C Electric Racing Boat unattended when it is plugged into its charger Turn off the R C Electronic Racing Boat and unplug it from its electri cal outlet before leaving WARNING Always remove the Battery Pack 16 from the Battery Compartment when it is being charged Always wear work gloves if removing the Propellers 4A and or 4B The blades can be very sharp If the R C Electric Racing Boat has been recently used SKU 95641 For technical questions please call 1 800 444 3353 Page 5 let the Twin 380 Motors 8A and 8B as well as both Drive Shafts 6B and 6C cool at least 15 minutes before touching 15 Do not recharge the Battery Pack 16 if it is hot GROUNDING AWARNING Improperly connecting the grounding wire can result in the risk of electric shock Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded Do not modify the power cord plug provided with the tool Never remove the grounding prong from the plug Do not use the tool if the power cord or plug is damaged If damaged have it repaired by a service facil ity before use If the plug will not fit the outlet have a proper outlet installed by a qualified electrician GROUNDED TOOLS TOOLS WITH THREE PRONG PLUGS 1 Tools marked with Grounding Required have a three wire cord and thr
7. ded by the manufacturer for your model Accessories that may be suitable for one product may become hazardous when used on another SERVICE Product service must be performed only by qualified repair personnel Ser vice or maintenance performed by unqualified personnel could result in a risk of injury When servicing this product use only identical replacement parts Follow instructions in the Inspection Maintenance And Cleaning section of this manual Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury SPECIFIC SAFETY RULES Maintain labels and nameplates on the product These carry important infor mation If unreadable or missing contact Harbor Freight Tools for a replacement Maintain a safe working environment Make sure there is adequate surrounding workspace Always keep all electrical cords away from the propellers on this R C Electric Racing Boat SKU 95641 For technical questions please call 1 800 444 3353 Page 4 If two Boats with the same radio frequency are used both with the same numbers on the Transmitter and or Receiver they must be at least 1640 away from one another in order to maintain adequate transmission control Before using in the water perform a distance check to be certain that you can maintain radio control at least 25 from Transmitter to Boat with the Antenna collapsed NEVER run RIC Electric Racing Boat in swimming po
8. ee prong grounding plug The plug must be connected to a properly grounded outlet If the tool should electrically malfunction or break down grounding provides a low resistance path to carry electricity away from the user reducing the risk of electric shock See 3 Prong Plug and Outlet 2 The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool The green wire in the cord must be the only wire connected to the tool s grounding system and must never be attached to an electrically live terminal See 3 Prong Plug and Outlet 3 Your tool must be plugged into an appropriate outlet properly installed and ground ed in accordance with all codes and ordinances The plug and outlet should look like those in the following illustration See 3 Prong Plug and Outlet Noe 3 Prong Plug and Outlet Outlets for 2 Prong Plug SKU 95641 For technical questions please call 1 800 444 3353 Page 6 DOUBLE INSULATED TOOLS TOOLS WITH TWO PRONG PLUGS Note The Charger included with this R C Electronic Racing Boat has a 2 Pronged plug 1 Tools marked Double Insulated do not require grounding They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories Inc the Canadian Standard Association and the National Electrical Code See Outlets for 2 Prong Plug 2 Double insulated tools may
9. for complete idea of inside Hull layout CHARGING THE BATTERY 1 Plug the Charger 17 into a 120V wall outlet or into an extension cord that is con nected to a 120V outlet 2 After removing the Battery Pack 16 from the Battery Compartment under the Deck Cabin 1 plug the Battery Pack 16 into the Charger 17 Note Do not force the connectors as they will only connect one way Charge the bat teries only when they are cool 3 Charging time is approximately 3 5 to 5 Hours for totally discharged Battery Pack 16 but charging time may be reduced if the Battery Pack 16 is not fully dis charged 4 When Charging is completed re insert the Battery Pack 16 into the Battery Com partment and fasten down the Deck Cabin 1 using the two lock buttons at the back of the Deck Cabin 1 and one at the front AWARNING To prevent serious injury from fire or battery explosion DO NOT CHARGE FOR MORE THAN 5 HOURS The charger will not turn off or stop charging when the battery is fully charged Disconnect battery from charger when battery gets hot Overcharging can damage the Battery Pack and can pose a fire hazard REV 07e SKU 95641 For technical questions please call 1 800 444 3353 Page 10 OPERATION INSTRUCTIONS USING THE TRANSMITTER TO STEER Note See Figure 3 for Transmitter 20 layout 1 When you push the Throttle Lever on the Transmitter 20 forward the Twin Pro pellers will rotate at the same time and
10. g parts cracked or broken parts damaged electri cal wiring and any other condition that may affect its safe operation If abnormal noise or vibration occurs have the problem corrected before further use Do not use damaged equipment 2 AFTER EACH USE inspect the Racing Boat s transmission shaft and bearing for water Water may accumulate after each use resulting in rust or blocked trans mission shaft Dry the transmission shaft by taking the propeller down unscrew ing and removing the shaft struts and drying the shaft and strut bearings Adding lubricant to the shaft and bearings will also help prevent rust Once done reinstall all pieces Changing Boat Frequency a Turn off the boat and the remote control b Open the tabs of the boat cover and unscrew the electric speed controller hous ing c Lightly hold down the circuit board and replace the crystal d Screw down the electric speed controller housing and lock the top cover of the boat with the tabs e Pull out and replace the crystal on the controller to match the crystal in the boat The controller will only control the boat if it has the same frequency Troubleshooting Possible Causes Probable Solutions R C Electric Racing 1 Low Transmitter Batteries 1 Change the old 8 AA Batteries in Boat will not start Transmitter 20 for new ones 2 Battery Pack 16 not connected to 2 Remove the Deck Cabin 1 the Electric Speed Controller 18 and make sure the
11. ols or bodies of water where people are swimming or playing NEVER recharge non rechargeable batteries Use only batteries of the type recommended Do not mix old and new batteries Remove batteries from both the R C Electric Racing Boat and the Transmitter if they will not be used for a long period People with pacemakers should consult their physician before using this product Electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker In addition people with pace makers should adhere to the following e Avoid operating this R C Electric Racing Boat alone e Don t use this product with the power switch locked on e If powered via a power cord be certain that the tool is properly grounded A ground fault interrupt GFCI system is also a good precaution This inexpen sive device is a good safety measure because it prevents a sustained electrical shock e Properly maintain and inspect all tools before use to avoid electrical shock Never pick up or lay down the R C Electric Racing Boat until its Propellers come to a complete stop Moving parts can grab the surface and pull the R C Electric Racing Boat out of your control and there is the possibility of damage or personal injury When handling this Racing Boat be sure to keep hands clear of propellers at all times This product is for supervised use by ages 6 and up Children must be prop erly trained in safety issues an
12. ore using the R C Electric Racing Boat Figure 2 Electric Speed Controller Receptacle from Electric Speed Controller Plug from Battery Pack Battery Pack i 4 Ifthe Battery Pack 16 is plugged into the Electric Speed Controller 18 unplug them and remove the Battery Pack 16 from the Battery Compartment so it may be charged completely See Figure 2 SKU 95641 For technical questions please call 1 800 444 3353 Page 9 Note The Rechargeable Battery should be charged fully before its first use in order to get maximum run time for your R C Electric Racing Boat See Charging Instruc tions on page 10 5 After fully charging the Battery Pack 16 replace it into the Battery Compartment and plug it into the Electric Speed Controller 18 6 Replace the Deck Cabin 1 and lock it into place with the two Lock Buttons at the rear 7 install the Antenna Tube 3 over the string Antenna that dangles from the right rear of the Hull 2 See assembly diagram on page 15 8 Make sure the Power Switch on the Transmitter 20 is in the OFF position Open the Battery Compartment located on the bottom of the Transmitter 20 Insert new 8 AA Batteries not included making sure positive and negative ends are facing in the correct direction Replace the Transmitter Battery Compartment cover 9 After reading the Operation Instructions carefully you may launch your R C Electric Racing Boat Note See photo on page 16 of this manual
13. r to keep Boat on straight path if Steering Lever is not being used h Power Switch On Off button Make sure it is always in the OFF position before picking up the R C Electric Racing Boat USING THE RADIO CONTROLLED ELECTRIC RACING BOAT 1 With the Transmitter Power Switch and the boat power switch both in the OFF po sition place the Racing Boat in the water pointed away from the edge of the water space 2 Move the Power Switch to ON and gently push the Throttle Lever forward to move the Racing Boat forward 3 At first using low speeds practice turning and making the Racing Boat react to the commands of the Transmitter 4 Set the Throttle Trim and the Steering Trim before increasing speeds 5 Be aware of the time Do not run out of power while the Racing Boat is located far away from the launch area Once the power is depleted the Racing Boat will stop 6 Always make sure you are away from others while using your R C Electric Racing Boat in order to prevent accidents and or personal injury SKU 95641 For technical questions please call 1 800 444 3353 Page 12 INSPECTION MAINTENANCE AND CLEANING AWARNING Make sure the Power Switch of the R C Electric Racing Boat is in its OFF position and it is unplugged from its electrical outlet before performing any inspection maintenance or cleaning procedures 1 BEFORE EACH USE inspect the general condition Check for loose screws misalignment or binding of movin
14. rwriters Laboratories Inc Volts Alternating Current Amperes _ No Load Revolutions per Minute UNPACKING When unpacking check to make sure that the item is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover page of this manual as soon as possible Note Save the box and all Styrofoam packing that comes with this R C Electronic Rac ing Boat It is helpful for safe secure storage when it is not in use ASSEMBLY INSTRUCTIONS Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram on page 15 of this manual 1 AAWARNING Make sure the Power Switch of the Transmitter 20 is in its OFF position and that the R C Electric Racing Boat is unplugged from its electrical outlet before making any adjustments 2 Remove the R C Electric Racing Boat the Transmitter and all parts from the box Check to make sure everything is included as per the parts list on page 14 in this manual SKU 95641 For technical questions please call 1 800 444 3353 Page 8 3 Remove the Deck Cabin 1 by twisting the two Buttons at the back of the Deck Cabin 1 to OPEN This will expose the Battery Compartment See Figure 1 Note There is another Button for locking and unlocking the Deck Cabin 1 and it is located on the front section of the Deck Cabin 1 It is not shown in Figure 1 Be sure it is also locked bef
15. s Do not overreach Keep proper footing and balance at all times Proper foot ing and balance enables better control Use safety equipment Always wear eye protection Always wear ANSI ap proved safety goggles and work gloves when using or performing maintenance on this product SKU 95641 For technical questions please call 1 800 444 3353 Page 3 PRODUCT USE AND CARE Do not use the R C Electric Racing Boat if the Power Switch does not turn it on or off Any tool that cannot be controlled with the Power Switch is dangerous and must be replaced Disconnect the Power Cord Plug from the power source before making any adjustments changing accessories or storing the R C Electric Racing Boat Such preventive safety measures reduce the risk of starting accidently Always unplug from its electrical outlet before performing any inspection mainte nance or cleaning procedures Store out of reach of children and other untrained persons Never allow Chil dren to come in contact with this product Maintain with care and keep clean Properly maintained this product is easier to control Do not use if damaged in any way Tag and Do not use until repaired Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the R C Electric Racing Boat s operation If damaged have it serviced before using Many accidents are caused by poor maintenance Use only accessories that are recommen
16. speed pushing the Racing Boat forward 2 When you move the Steering Lever to the left the Right Propeller will rotate faster and the Racing Boat will turn left 3 When you move the Steering Lever to the right the Left Propeller will rotate faster turning the Racing Boat to the right Figure 3 Transmitter Antenna Battery Level Indicators s Throttle Trim Throttle Lever Steering Lever Throttle Inverter Steering Trim Crystal Steering Inverter Power Switch 4 The Transmitter layout is as follows a Battery Level Indicators Green light means Transmitter Batteries are strong If Red light is flashing and a beeping is heard replace the 8 AA Bat teries at once b Throttle Trim Adjusts the Throttle in small increments so the R C Electric Racing Boat will not move when the Throttle is at it s minimum position c Throttle Lever Controls the speed of the R C Electric Racing Boat and it s move ment forward d Inverter Buttons Used for changing direction for steering This boat cannot travel in reverse however REV 07e SKU 95641 For technical questions please call 1 800 444 3353 Page 11 e Crystal This shows the channel you are transmitting on You can order crystals in different channels in order to race with other boats without transmission interfer ence f Steering Lever Used to turn R C Electric Racing Boat to the left or right g Steering Trim Used to make slight adjustments in orde
17. ug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install a polarized outlet Do not change the plug in any way Double insulation E eliminates the need for the three wire grounded power cord and grounded power supply system Do not abuse the Power Cord Never use the Power Cord to carry the tools or pull the Plug from an outlet Keep the Power Cord away from heat oil sharp edges or moving parts Replace damaged Power Cords immediately Damaged Power Cords increase the risk of electric shock When operating a power tool outside use an outdoor extension cord marked W A or W These extension cords are rated for outdoor use and reduce the risk of electric shock PERSONAL SAFETY Stay alert Watch what you are doing and use common sense when operat ing this R C Electric Racing Boat Do not use while tired or under the influ ence of drugs alcohol or medication A moment of inattention while operating may result in serious personal injury Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in propellers Avoid accidental starting Be sure the Power Switch is off before plugging in Carrying this R C Electric Racing Boat with your finger on the Power Switch invites accident
Download Pdf Manuals
Related Search