Harbor Freight Tools 95365 User's Manual
Contents
1. Figure 1 2 Slide the Bottom Support Assembly Brace 7 down over the Post 2 until it is at the adjustment holes Set the Bottom Support Assembly Holder 4 and the Bottom Support Assembly Brace 7 so that they line up on each side of the desired hole Thread the Handle Wheel 13 into the Bottom Support Assembly Brace 7 Slide Washer 5 onto the threaded end of the Handle Wheel 13 and thread on Nut 6 to secure it in place see Figure 2 SKU 95365 For technical questions please call 1 800 444 3353 Page 3 Bottom Support Assembly Brace 7 Bottom Support Assembly Holder 47 Nut 6 f e Handle Wheel 13 Washer 3 Attach the Top Support Assembly 15 to the top two holes on the Post 2 Secure in place using two Screws 3 see Figure 3 Top Support Assembly 15 Screw 3 Figure 3 OPERATION INSTRUCTIONS 1 Position the Workstandin a location where it will not be an obstruction to passersby Place it on a smooth flat and level surface capable of supporting the Workstand and the weight of the bicycle and components 2 The Bottom Support Assembly Holder is adjustable Set the Bottom Support As sembly Holder 4 to the desired height With the bicycle upside down set the top tube flat horizontal tube nearest the seat of the bicycle onto the Bottom Support Assembly Holder 4 Rest the bottom of the bicycle in the Top Support Assembly 15 INSPECTION MAINTENANCE AND CLEANING 1 BEFORE EA2. BICYCLE WORKSTAND 150 LB CAPACITY ASSEMBLY AND OPERATION INSTRUCTIONS Due to continuing improvements actual product may differ slightly from the product described herein Distributed Exclusively by i re HARBOR FREIGHT 7 i3 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http Awww harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 SPECIFICATIONS Maximum Weight Capacity 150 Lbs Overall Dimensions 13 5 8 L X 12 1 8 W X 23 H 14 gauge steel support bracket steel tubing with Material black enamel finsh thermoplastic hardware caps rubber support bracket cover Seven Adjustment Positions 18 5 8 17 3 17 16 1 4 15 1 2 14 5 8 distance from the ground 14 You will need this manual for the safety warnings and precautions assembly oper ating inspection maintenance and cleaning procedures parts list and assembly diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Write the product s serial number in the back of the manual near the assembly dia gram or write mon
3. CH USE inspect the general condition of the tool Check for loose screws misalignment or binding of moving parts cracked or broken parts and any other condition that may affect its safe operation Do not use damaged equip ment SKU 95365 For technical questions please call 1 800 444 3353 Page 4 PARTS LIST Part Description Q ty Part Description _ Q ty 1 cover 4 9 flegassembya 2 5 Washer e 13 Hanewnei 1 6 iN eju w i 7 Bottom Support Assy Brace 1 15 Top Support 1 Assembly PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEM BLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS SKU 95365 For technical questions please call 1 800 444 3353 Page 5 ASSEMBLY DIAGRAM SKU 95365 For technical questions please call 1 800 444 3353 Page 6
4. embled parts after assembling All connections should be tight and hardware tightened Do not exceed the Bicycle Workstand maximum weight capacity of 150 Lbs evenly distributed Never allow anybody to tamper with a bicycle while it is being supported on the Workstand SKU 95365 For technical questions please call 1 800 444 3353 Page 2 UNPACKING When unpacking check to make sure that the item is intact and undamaged If any parts are missing or broken see parts list assembly diagram please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible ASSEMBLY INSTRUCTIONS Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram on page 6 of this manual The Bicycle Workstand can be easily assembled by taking the following steps The Work stand will stand on its own and will hold up to 150 Lbs evenly distributed 1 Set one Leg Assembly A 9 and Leg Assembly B 11 on each side of the Post 2 so that the holes line up with the holes at the bottom of the Post 2 Through the lowest hole insert Screw 8 and thread on Nut 12 see Figure 1 Through the next hole up insert the Screw 8 from the opposite direction and thread on Nut 12 see Assembly Diagram Attach Leg Covers 10 to the end of each leg not shown in Figure 1 Post 2 lt Leg Cover 10 ut 12 Screw 8 a Nut 12 SE 8 ce os SNA Leg Assy B 11
5. th and year of purchase if product has no number Keep this manual and invoice in a safe and dry place for future reference 11 12 GENERAL SAFETY RULES Keep your work area clean and well lit Cluttered benches and dark areas invite accidents Keep bystanders children and visitors away while assembling and working with the Workstand Distractions can cause you to lose control Stay alert Watch what you are doing and use common sense when operating this product Do not use while tired or under the influence of drugs alcohol or medi cation A moment of inattention while operating this product may result in serious personal injury or property damage Dress properly Do not wear loose clothing or jewelry Contain long hair Loose clothes jewelry or long hair can be caught in parts of the Workstand and bicycle Keep proper footing and balance at all times Proper footing and balance enables better control of the Bicycle Workstand in unexpected situations Use safety equipment Always wear eye protection Always wear ANSI approved leather work gloves when working with the Workstand Store the Bicycle Workstand out of reach of children and other untrained persons This product could be dangerous in the hands of untrained users Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may become hazardous when used on another tool Always check hardware and ass
Download Pdf Manuals
Related Search