Harbor Freight Tools 95141 User's Manual
Contents
1. are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS CONNECTING TO AN AIR SUPPLY 1 For best service you should incorporate an oiler regulator and in line filter as shown in the diagram below Hoses couplers oilers regulators and filters are all available at Harbor Freight Tools NOTE If an automatic oiler is not used put 3 5 drops of pneumatic Tool Oil not included in the tool s quick connector before each use See Figure A REGULATOR Psion gm PRT FD si O TTT ates Ap w VY FIGURE A OILER FILTER 706k SKU 95141 For technical questions please call 1 800 444 3353 PAGE 4 ASSEMBLY INSTRUCTIONS 1 Prior to use the Impact Wrench requires the attachment of a 3 8 18 NPT Quick Connector not included to its Air Inlet 45 To do so make sure the screen Air Filter 44 is properly seated in the Air Inlet Wrap approximately 3 of pipe thread sealer tape not included around the male threads of the Quick Connector Then firmly tighten the Quick Connector into the Air Inlet See Figure B QUICK CONNECTOR NOT INCLUDED FIGURE B OPERATING INSTRUCTIONS WARNING Use eye and hearing protection Always wear ANSI approved safety impact goggles when using this Impact Wrench Also wear ANSI approved hearing protection Other people in the work area must also wear appropriate ANSI approved safety equipment 2 Wh2. as soon as possible SAFETY WARNINGS AND PRECAUTIONS WARNING Use eye and hearing protection Always wear ANSI approved safety impact goggles when using this Impact Wrench Also wear ANSI approved hearing protection Other people in the work area must also wear appropriate ANSI approved safety equipment 2 Keep work area clean Cluttered areas invite accidents 3 Stay within air pressure capacity Never operate the Impact Wrench above 90 PSI 4 Observe work area conditions Keep work area well lit Do not use pneumatic SKU 95141 For technical questions please call 1 800 444 3353 PAGE 2 10 11 12 13 14 tools in the presence of flammable gases or liquids Keep children away Children must never be allowed in the work area Do not let them handle machines tools extension cords or air hoses Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children Use the right tool for the job Do not attempt to force a small tool or attachment to do the work of a larger industrial tool There are certain applications for which this tool was designed It will do the job better and more safely at the rate for which it was intended Do not modify this tool and do not use this tool for a purpose for which it was not intended Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protectiv
3. CENTRAL PNEUMATIC Professional HEAVY DUTY TWIN HAMMER 3 4 IMPACT WRENCH Model 95141 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements actual product may differ slightly from the product described herein Distributed Exclusively by a HARBOR FREIGHT a iy 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions please call 1 800 444 3353 PRODUCT SPECIFICATIONS O ltem Description _ 9600 SAVE THIS MANUAL You will need this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures parts list and assembly diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep this manual and invoice in a safe and dry place for future reference UNPACKING When unpacking check to make sure that all the parts and accessories listed on page 8 are included and the product is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual
4. L PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 95141 For technical questions please call 1 800 444 3353 PAGE 7 PARTS LIST Valve Bushing Trigger lade pring Washer crew lutch Housing 5 6 7 8 7 Rotor SS O ep Rotor Rear End Plate 10 TI 20 ALAR AIAI BR BR BR BR OUOU G01 Nw 1G G M M PPO PO BLO O O 0 N O 01 BR G M 1O O 00 N Oo 01 Part eee aa B 9 10 E Sold only as an assembly Sold only as an assembly SKU 95141 For technical questions please call 1 800 444 3353 PAGE 8 ASSEMBLY DIAGRAM i 2 34 6 i 8 9 1011 12 13 id 15 NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts WARRANTY XY SW WANS JN gt VMN NAN SVAN CENTRAL PNEUMATIC LIMITED 2 YEAR ENP gt e Read Professional WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards SLAW and warrants to the original purchaser that this product is free from defects in materials and workmanship for the K period of 2 years from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities or to lack of maintenance Y We shall in no event be liable fo
5. e electrically non conductive clothes and non skid foot wear are recommended when working Wear restrictive hair covering to contain long hair Do not overreach Keep proper footing and balance at all times Do not reach over or across running tools or air hoses Disconnect air hose and release any built up air pressure Never service the Impact Wrench or disassemble with the air hose attached Always release any built up air even after disconnecting hose Disconnect the Impact Wrench when not in use Avoid unintential starting Be sure the Trigger 27 is in the OFF position when not in use and before plugging in Do not carry any tool with your finger on the Trigger whether it is attached to an air source or not Stay alert Watch what you are doing Use common sense Do not operate any tool when you are tired or distracted Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Do not use the tool if the Trigger does not operate properly Replacement parts and accessories This product is to be repaired and serviced only by a qualified technician When this product is serviced only identical re
6. enever possible secure the workpiece in place using a vise or clamps not included 3 Make sure the Impact Wrench is disconnected from its air supply hose prior to installing or changing sockets not included on the tool 4 Select the proper 3 4 impact socket for the job at hand Then firmly insert the socket onto the Anvil 39 of the Impact Wrench See Figure C next page D The Impact Wrench features a Forward Reverse Valve 21 that allows you to change the rotational direction of the tool For a forward clockwise rotation move the Forward Reverse Valve to the left For a reverse counterclockwise rotation move the Forward Reverse Valve to the right See Figure C SKU 95141 For technical questions please call 1 800 444 3353 PAGE 5 6 Connect the air supply hose not included to the previously installed Quick Connnector of the Impact Wrench See Figure C 7 Turn on the air compressor and set its regulator at 90 PSI Do not exceed 90 PSI 8 Wait until the air compressor s regulator reaches 90 PSI Then insert the previously installed socket onto the nut that is to be loosened or tightened 9 Make sure to hold the Impact Wrench firmly with both hands as torque from the tool will cause the tool to twist Then squeeze the Trigger 27 to turn on the tool See Figure C 10 While the work is in progress you may need to change the directional rotation of the tool To avoid damaging the Impact Wrench al
7. il a qualified service technician repairs the tool INSPECTION MAINTENANCE AND CLEANING 1 WARNING Always wear ANSI approved safety impact goggles when performing any inspection maintenance or cleaning procedures 2 N WARNING Prior to performing any inspection maintenance or cleaning of the Impact Wrench make sure to disconnect the air hose from the tool Then squeeze the Trigger 27 again to release any compressed air in the system and tool 3 To clean the exterior of the Impact Wrench wipe with a clean damp cloth using amild detergent or mild solvent Do not immerse the tool in liquids 4 When storing always store the Riveter in a clean dry safe location out of reach of children 5 N CAUTION All maintenance service and repairs not mentioned in this manual must only be performed by a qualified service technician PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINA
8. placement parts should be used Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools SKU 95141 For technical questions please call 1 800 444 3353 PAGE 3 15 Do not operate tool if under the influence of alcohol or drugs Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs If there is any doubt do not operate the tool 16 Maintenance The maintenance outlined in the Maintenance section of this manual should be performed regularly For your safety this product should be serviced or repaired regularly only by a qualified technician 17 Compressed air only Use clean dry regulated compressed air at 90 PSI Never use oxygen carbon dioxide combustible gases or any other bottled gas as a power source for this tool 18 Always grip the Impact Wrench firmly with both hands when operating the tool 19 Industrial applications must follow OSHA requirements 20 Maintain labels and nameplates on the Impact Wrench These carry important information If unreadable or missing contact Harbor Freight Tools for a replacement 21 AN WARNING The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution
9. r death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS i A ZNE INS A To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of your warranty then you must bear the cost of returning the product NY Y AN A K N NAS This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 CARN NANT NST ANANN NANA NAO NANANA SKU 95141 For technical questions please call 1 800 444 3353 PAGE 9 TI
10. ways make sure the tool is ata complete stop before changing the rotational direction See Figure C 11 When finished release the Trigger 27 to stop the Impact Wrench See Figure C 12 Turn off the air compressor Squeeze the Trigger 27 of the Impact Wrench to release any remaining air pressure in the system and tool Disconnect the tool from its air supply hose Then remove the socket from the tool and store the socket in a safe location See Figure C 13 Make sure to store the Impact Wrench in a clean dry safe location out of reach of children and other unauthorized people SOCKET NOT INCLUDED FORWARD REVERSE VALVE 27 AIR SUPPLY HOSE NOT INCLUDED FIGURE C SKU 95141 For technical questions please call 1 800 444 3353 PAGE 6 TROUBLESHOOTING Possible Solution Impact Wrench does not turn on when Make sure to firmly squeeze the Trigger 27 Trigger is squeezed Make sure air compressor is on and its regulator is set at 90 PSI Make sure all air system connections are secure and that there are no leaks Make sure the air and oil filters in the air compressor are not plugged Make sure the Air Filter 44 within the Air Inlet 45 is not plugged Releasing the Trigger on the Impact Turn off the air compressor Release any remaining Wrench does not turn off the tool compressed air from the system and tool Disconnect the air supply hose from the tool Do not use the tool unt
Download Pdf Manuals
Related Search