Harbor Freight Tools 94847 User's Manual
Contents
1. be built into this product but must be supplied by the operator SKU 94847 For technical questions please call 1 800 444 3353 Page 3 Unpacking When unpacking check to make sure the following parts are included Refer to the Parts List and Assembly Drawing located at the end of this manual If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual as soon as possible Regulator 11 Air Hammer 10 Screw 2 Hammer Head 3 Anvil 5 Adjustable Pole 7 Stopper Pin 9 Air Hose 12 i z 4 Range Adjust Block 6 i fs Switch Assembly 13 DE Mounting Holes Qty 4 Installation Mounting C Frame 1 Select a workbench in the shop area able to support the weight of the Planishing Hammer the metal being worked on and the vibration of the planishing process 2 Mount the C Frame 1 to the workbench using hardware not supplied The C Frame should be positioned so that the mounted Air Hammer 10 is extended slightly over the edge of the workbench This will accommodate various shapes of metals being planished Hardware should consist of nuts bolts flat washers and lock washers Note There is an entry hole on the side of C Frame 1 where sand can be inserted to reduce noise and vibration Air Connection 1 Attach a Union fitting not supplied into the Switch Assembly Inlet 13 fitt2. ACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 94847 For technical questions please call 1 800 444 3353 Page 7 Assembly Drawing SKU 94847 For technical questions please call 1 800 444 3353 Page 8 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint m
3. CENTRAL PNEUMATIC Sy PNEUMATIC PLANISHING HAMMER iooi 94847 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements actual product may differ slightly from the product described herein Distributed Exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com Copyright 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Specifications 875 1350 BPM Operating Air Pressure 50 to 100 maximum PSI 4 SCFM Air Inlet 1 4 18 NPT female Overall Dimensions 23 L x 5 1 2 W x 24 H inches C frame and Hammer Anvil to Hammer Opening 4 inches maximum Anvil Height Adjustment 2 position anvil shaft mount with lock pin 3 8 to 1 1 4 opening between head and anvil 4 position stepped anvil micro adjustment block 1 16 height difference between each level 1 Radius 2 Radius and 3 Radius Throat Depth 19 5 8 inches Foot Pedal 7 1 4 L x 4 W x 3 1 2 H inches Built in air filter Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manu
4. Frame is Unscrew Screw 2 so it is out of the way of the Air Hammer 10 when inserting it into the C Frame Do not remove Screw 2 See photo below right al _Air Hammer 10 aa n Hammer Head 3 C Frame Coil Spring Hammer Sleeve 4 Screw 2 Anvil 5 screw off the Coil Spring from the Air Hammer 10 and slip it off along with the Hammer Head 3 and Hammer Sleeve 4 See photo below left Slide the Air Hammer body into the C Frame mounting hole as shown below right Insert the desired size Anvil 5 onto the Adjustable Pole 7 Place the Hammer Head 3 through the Coil Spring then into the Air Hammer screw on the Coil Spring until it stops Retighten Screw 2 completely SKU 94847 For technical questions please call 1 800 444 3353 Page 5 Operation To change the height of the Anvil 5 to within 1 1 2 inches of the desired height pull out Stopper Pin 9 and move the Adjustable Pole 7 up or down to one of two Stopper Pin holes Replace Stopper Pin To adjust closer to the desired height move the Range Adjust Block 6 to the right or left to reach the desired height Turn on the Air Compressor and set its regulator to 90 PSI Before planishing test the operation by pressing down on the foot Switch Assy 13 with your foot Adjust the cycle speed of the Air Hammer by turning the Regulator 11 valve clockwise or counterclockwise Use both gloved hands to hol
5. al Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using tool basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using this tool 1 Keep work area clean Cluttered areas invite injuries 2 Observe work area conditions Do not use machines or power tools in damp or wet locations Don t expose to rain Keep work area well lighted Do not use electrically powered tools in the presence of flammable gases or liquids 3 Keep children away Children must never be allowed in the work area Do not let them handle machines tools or extension cords 4 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children 5 Use the right tool for the job Do not attempt to force a small tool or attachment to do the work of a larger industrial tool There are certain applications for which this tool was designed It will do the job better and more safely at the rate for which it was intended Do not modify this tool and do not use this tool for a purpose for which it was not intended 6 Use eye and ear protection Always wear ANSI approved impact safety goggles Wear a full face shield if you are producing metal filings T Dress properly Do
6. amaged should be properly repaired or replaced by a qualified technician Do not use the tool if any switch does not turn On and Off properly Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools Do not operate tool if under the influence of alcohol or drugs Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool Maintenance For your safety service and maintenance should be performed regularly by a qualified technician Compressed air only Never use combustible gas as a power source Protect hands and body from injuries Always wear leather gloves and body protection when handling metal for use on the Planishing Hammer Keep hands fingers and arms away from the hammer head and anvil during operation Install this product on a proper surface Locate on a flat level and solid surface that is capable of supporting the weight of the Planishing Hammer and the material being hammered Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot
7. d the material to be planished and place it between the Anvil 5 and the Hammer Head 3 Press down on the Switch Assy 13 on the floor with your foot to operate When finished planishing remove your foot from the Switch Assy and wait for the Air Hammer to stop completely Turn the Air Compressor off Press down on the Switch Assy 13 again to release any remain air pressure in the Air Hammer Changing Anvils 1 Unscrew Screw 2 so it is out of the way of the Air Hammer 10 when removing it from the C Frame Do not remove Screw 2 See photo on page 5 bottom right Screw off the Coil Spring from the Air Hammer 10 and slip it off along with the Hammer Head 3 and Hammer Sleeve 4 See photo on page 5 bottom left Slide the Air Hammer body out of the C Frame mounting hole Replace Anvil 5 with desired size onto the Adjustable Pole 7 Replace the Air Hammer into the C Frame Then attach the Hammer Head 3 through the Coil Spring then into the Air Hammer Screw on the Coil Spring until it stops Retighten Screw 2 completely Troubleshooting Probable Cause Planishing Hammer does not No air pressure in air line Check air line and compressor operate when Switch pressed Planishing Hammer operates Air pressure below normal Check regulator on at diminished pressure operating pressure compressor and Air Hammer SKU 94847 For technical questions please call 1 800 444 3353 Page 6 Mai
8. ing A Union fitting is necessary before a connection can be made to an Air Compressor 2 For easy connection or removal attach an Air Coupler not supplied to the Union fitting if quick coupling is desired Retighten all couplings and fittings 4 Attach the Air Hose not supplied from the Air Compressor not supplied to the Switch Assembly 13 Place Switch Assy on the floor next to the Planishing Hammer SKU 94847 For technical questions please call 1 800 444 3353 Page 4 Caution Do not turn on the Air Compressor at this time Oiler and Filter Connection Dirt water and the lack of pneumatic tool oil are major causes for tool wear Install an optional oiler filter not supplied as illustrated below for better performance QUICK QUICK REGULATOR i a i AIR COMPRESSOR Nags Woe wears 00 eG AR TOOL OR DEVICE aN lab AIR om LM HOSE QUICK QUICK COUPLER H AIR FILTER OILER COUPLER Connect the air tool air hoses filter and oiler to the Compressor Air Outlet as illustrated below Use pipe thread seal or Teflon tape on all threaded connections The filter and oiler not supplied are recommended but not mandatory for operation If the filter and oiler are not used connect the air hose directly to the 1 4 inch 18 NPT connector located at the Air Switch Assembly Inlet 13 fitting Also a few drops of pneumatic tool oil must be added through the air line before each use Mounting Air Hammer to C
9. not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically non conductive clothes and non skid footwear are recommended when working Wear restrictive hair covering to contain long hair REV 07j SKU 94847 For technical questions please call 1 800 444 3353 Page 2 10 11 12 13 14 15 16 17 18 19 Do not overreach Keep proper footing and balance at all times Do not reach over or across running machines Maintain tools with care Keep tools sharp and clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect tool cords periodically and if damaged have them repaired by an authorized technician The handles must be kept clean dry and free from oil and grease at all times Disconnect air supply Unplug tool from air supply when not in use Remove adjusting keys and wrenches Check that keys and adjusting wrenches are removed from the tool or machine work surface before operation Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is d
10. ntenance 1 After each use wipe all components of the Planishing Hammer with a clean cloth to remove any dirt and grease buildup 2 To maintain tool life always lubricate the air line by adding a few drops of pneumatic tool oil to the air line or Air Inlet before each use Or install the automatic oiler filter system as illustrated on page 5 3 Before each use drain water out of the air compressor tank and condensation from the air lines Refer to the Air Compressor Operation Manual 4 Cover the Planishing Hammer and keep in a clean and dry location Parts List Description _ 1 Cover S 1 1 1 1 1 1 1 Cover PVC Air Hose Hose Clamp Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPL
11. ust accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 SKU 94847 For technical questions please call 1 800 444 3353 Page 9
Download Pdf Manuals
Related Search