Harbor Freight Tools 93974 User's Manual
Contents
1. 1 Dirt on one side of the fluid tip Clean the fluid tip 2 Holes on one side of the Air cap are plugged Clean the Air cap with a non metallic point SKU 93974 For technical questions please call 1 800 444 3353 Page 18 Troubleshooting continued Cause Solution Sputtering Spray Low material level Cup tipped too far Clogged Air Vent Loose fluid inlet connections Dry or loose fluid needle Packing Nut Loose damaged fluid tip seat Refill Hold upright Clean vent hole Tighten Lubricate and or tighten Adjust or replace Will Not Spray No pressure at gun Fluid control not open enough Fluid too thick Check air hoses Open fluid control Thin fluid or increase pressure within Maximum range Overspray Improper application speed Improper distance from workpiece Too much pressure Move moderately and parallel Adjust distance Reduce air pressure Fluid Tip Leakage Dirty tip Tight Packing Nut Broken fluid needle spring Worn or damaged tip Clean Loosen Packing Nut Replace Replace tip and or needle Air Leaking from Air Cap Dirty air valve seat Sticking air valve Damaged air valve spring Worn damaged air valve seat Bent valve stem Clean Lubricate Replace Replace Replace Fluid Leaking from Packing Nut SKU 93974 Packing Nut loose Packing worn or dry For techni2. Disconnect from the air source After disconnecting be aware that air pressure may still remain in the Spray Gun Point the Gun into the spent solvent container and squeeze the Trigger again to make sure no air remains 3 Remove the Air Cap and soak it in solvent until it is clean Use an old toothbrush and toothpicks to remove any material Do not use metal objects to clean the Air Cap or you may damage the drilled passages Inspect the fluid needle and make sure it is not bent If itis bent have it replaced by a certified service technician Warning Do not immerse the Spray Gun Body in solvent 4 Use the appropriate solvent depending on the material sprayed to wipe down the Gun body 5 Always lubricate the Spray Gun after cleaning You may use a non silicon oil or a light lubricant on all threaded connections prior to storing the unit 6 Disposal After cleaning your Spray Gun properly dispose of your cleaning solutions according to the solution manufacturer s direction and local hazardous waste standards SKU 93974 For technical questions please call 1 800 444 3353 Page 12 Maintenance continued Disconnect from the air source Warning The Paint Cup and Spray Gun may still hold air pressure fire the Spray Gun toward scrap material until all of the pressure is expended Remove the Paint Cup N Pour residual paint into the paint container and seal it Pour non flammable paint thinner into the Paint Cup If water
3. Pattern Control Ass y Stem He oO W Needle 1 Locknut Air Inlet Assembly 41 47 Stem Locknut Siphon Tube 10 1 SKU 93974 1 12 O Ring 13 Pattern Control Knob 14 Washer Spindle 2 b d d d d t Cowhide Washer Fluid Needle Packing 1 Packing Nut 1 Body 6 1 27 Washer E ae 29 Fluid Controtknob 1 46 LidGasket 1 15 0S 30 Nut 31 Packing 48 Vent Tube Arm 44 Cup Locking Lever 45 Canister Lid Vent Cap i i i 2 NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts For technical questions please call 1 800 444 3353 Page 14 Assembly Diagram SKU 93974 For technical questions please call 1 800 444 3353 Page 15 Parts List Small Gun Note When ordering parts from this diagram add an A suffix For example Air Cap is part number 1A SKU 93974 DESCRIPTION DESCRIPTION Air Cap Air Inlet Inner Ring Needle Retainer Ring Lock Nut Fluid Nozzle Rear Nut Ring 10 Packing 11 Vol Adj Screw Receiver 1 Spring Fluid Control Knob Lever Yoke d a d ad Trigger Fluid Stem Lid ae 13 Gun Housing 14 15 Trigger Screw Lid Nut 16 Packing Cup 17 Nut 19 Packing 1 Val
4. Gun ile Remove the lid from the Paint Cup 47 or 34a Insert a Filter included into the top of the Paint Cup This will prevent dirt and debris from entering the Paint Cup 2 Fill the cup with material that has already been checked for viscosity Close the Paint Cup tightly to avoid leakage Mount the Paint Cup to the Spray Gun Make sure that the Paint Cup is securely attached a Connect the air source hose to the Air Inlet 40 or 23a Turn on your air compressor Do not exceed the maximum PSI 4 Squeeze the Trigger slowly and move the Spray Gun in parallel strokes to the object being painted Keep the distance from the object being painted at 6 to 9 This may slightly differ depending on the flow adjustment and the material being sprayed 5 Release the Trigger after each forward movement squeeze the Trigger again on the return movement 6 When using a vertical pattern move the Spray Gun in a horizontal motion with a hori zontal pattern move the Spray Gun in a vertical motion A round pattern requires a greater distance from the object being painted Note Gun adjustments on page 7 9 T When finished release the Trigger and disconnect the sprayer from the air source The Paint Cup and Spray Gun may still hold air pressure fire the Spray Gun toward scrap material until all of the pressure is expended 8 Immediately follow the Maintenance instructions on page 13 and 14 to avoid paint quickly drying in your Spray Gu
5. No SS IN N ae To take advantage of this warranty the product or part must be returned to us with transportation charges CA prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our X SY IXIA inspection verifies the defect we will either repair or replace the product at our election or we may elect to YZ A RLY refund the purchase price if we cannot readily and quickly provide you with a replacement We will return ney AA ly repaired products at our expense but if we determine there is no defect or that the defect resulted from NYX PSY causes not within the scope of our warranty then you must bear the cost of returning the product Ne lt A VIN CA This warranty gives you specific legal rights and you may also have other rights which vary from state to state ZA vA RS KG 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 NSA d D ez KATINAS OOS SARS SOOO SN AOS SOS NS IOS SS RES ZAN KANNIK AONIK ONNAN INKON SINS OSI INS SASS JA W AAN V DN V DN 7 IN F DN v DIN v ANN AN V NANNA NANSA NANANA IN PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
6. QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 93974 For technical questions please call 1 800 444 3353 Page 17 Troubleshooting Spray Pattern Diagnosis The Patterns below resemble symptoms of spray pattern problems Please refer to the accompanying possible problems if you are experiencing similar difficulties The solution to each problem follows the problem in parentheses Problem 1 Q 1 The Pattern Control Knob 13 or 12a is partially closed Open Pattern Control Knob 2 The material is too thick Thin material according to the manufacturer s instructions 3 The air pressure is too low Increase air pressure within the Maximum PSI 40 Problem 2 l 1 High air pressure Reduce air pressure 2 Not enough fluid Increase fluid 3 Pattern Control Knob 13 or 12a open too much Partially close Pattern Control Knob Problem 3 0 Q 1 Air Cap plugged Clean the Air Cap 2 Air cap loose or dirty seat Clean and tighten 3 Dried material on fluid tip Use a non metallic point to clean the Air Cap Problem 4
7. m tol Begin Squeeze Release Stroke Trigger FIGURE 6 Trigger Stroke Top View Note The speed of the stroke the adjustment of the Fluid Control Knob 28a or 29 and the distance from the workpiece will determine how much paint is being applied To get the best results try to apply two thin coats of paint versus one thick coat 3 Clean out the gun thoroughly after EVERY use according to the instructions found on the next page SKU 93974 For technical questions please call 1 800 444 3353 Page 10 Operation Paint and Materials Preparation Verify with the paint or materials supplier the percentage of thinning required for use with these Sprayers Try thinning a small amount and testing the spray action Thoroughly mix material before testing Viscosity Viscosity is the technical term used to indicate the liquidity thickness or thinness of the material being sprayed Viscosity is measured in the number of seconds required for the material to pass through the viscosity tester not included We recommend that you use a viscosity tester and follow all of the directions in the viscosity tester s safety and operations manual Preparing the area I Mask all objects you do not want sprayed 2 Lay a Paint Cloth not included on the floor and attach Paint Cloths not included to the surrounding walls Preparing and Operating both Spray Guns Note We recommend you practice on scrap material to adjust and become familiar with the
8. may cause the spray to come out too fine Reduce the air pressure or allow more material to come out by opening the Fluid Control Knob If the spray appears too thick you see globs of paint close down the Fluid Control Knob slowly checking the mix ture after each adjustment See FIGURE 4 below FIGURE 4 Too Coarse Correct Too Fine Tighten Loosen SKU 93974 For technical questions please call 1 800 444 3353 Page 9 Techniques Note Before spraying mask all objects you do not want sprayed and lay cloths not included on the floors il Always keep the gun at right angles to the workpiece See FIGURE 5 Pull the Trigger slowly and move the Spray Gun in parallel strokes to the object being painted Keep the distance from the object being painted at 6 to 9 This may slightly differ depending on the flow adjustment and the material being sprayed Do not stop the gun movement while spraying If you stop the gun for even just a slight pause while spraying the paint will build up and run down the workpiece FIGURE 5 Heavier coat on one side uneven coverage Incorrect Even coverage Correct 90 2 To ensure you don t allow paint to build up start moving the Spray Gun before you Squeeze the Trigger When you are finished spraying release the Trigger before you stop moving the Spray Gun Doing so will eliminate distinct overlaps producing a blended feathered affect See FIGURE 6 below m m
9. CENTRAL PNEUMATIC _ SN lt i 37 PIECE SPRAY GUN KIT ASSEMBLY and OPERATING INSTRUCTIONS Distributed Exclusively by ail HARBOR FREIGHT Ai os TOOLS wih 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Specifications Operating PSI 50 70 PSI Large Gun 30 50 PSI Small Gun Air Consumption 16 SCFM Large Gun 8 SCFM Small Gun Spray Guns 1 Large Spray Gun with 32 oz paint cup 1 8mm nozzle 1 Small Spray Gun with 7 oz paint cup 1 5mm nozzle Air Inlet Both Guns 1 4 NPS Materials Cast Aluminum Gun Bodies Brass Nozzle amp Fittings Sheet Metal Trigger Large Gun Cast Zinc Trigger Small Gun Spun Aluminum Paint Cups Polyurethane Air Hose Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoic
10. based paint was used you can use water Secure the Paint Cup to the appropriate Gun and shake the liquid in the cup Connect to the air source and turn on the air compressor Spray the liquid onto a piece of scrap material until the spray material is free of paint Repeat if necessary o NOOO Ff After following the above procedure use the cleaning brushes and to further clean the Spray Guns 9 Allow the Spray Guns to dry completely before storage Accessories Description Extra 32 oz Siphon Feed Paint Cup Extra 8 oz Siphon Feed Paint Cup Round Bristle Brush Flat Bristle Brush Wooden Toothpick Cleaning Needle Paint Filter 25 Recoil Hose 19 64 OD 1 4 18 NPT IN OUT Mail Brass Fittings Blow Gun Nozzles Rubber Tapered Safety and Needle Male Connector Female Connector Female Coupler Male Nipple Female Nipple Pipe Thread Seal Tape SKU 93974 For technical questions please call 1 800 444 3353 Page 13 Part Description QTY 1S Air Cap Set 1 3 Parts List Large Gun 17S Air Cap Assembly 17 20 Wiper Part Description Part Description QTY 32 Body Valve N Screw Body b d b d t d d Housing Assembly 23 25 1 2 Lock Ring Retainer Gasket 3 Zinc Ring Sleeve Spring 4 Fluid Nozzle 20 Wiper Screw 5 Head 21 Gasket Stud 6 Trigger Screw
11. cal questions please call 1 800 444 3353 Tighten without restricting 2 Replace or lubricate non silicone Page 19
12. d the recommended operating pressure of the any of the parts i e hoses fittings gun of the Sprayer system Do not spray near open flames pilot lights stoves heaters the air compressor or any other heat source Most solvents and coatings are highly flammable particularly when sprayed Maintain a distance of at least 25 feet from the air compressor If possible locate the air compressor in a separate room Do not smoke while spraying SKU 93974 For technical questions please call 1 800 444 3353 Page 3 21 22 23 24 25 26 27 Read all of the information concerning coating products and cleaning solvents Chlorinated solvents e g 1 1 1 Trichlorethylene and Methylene Chloride also known as methyl chloride can chemically react with aluminum and may explode Many paint sprayers contain aluminum If you have any doubt about potential chemical reactions contact the solvent or coating manufacturer Materials used when painting or cleaning may be harmful or fatal if inhaled or swallowed Only use in an area with adequate ventilation Use a respirator or mask when painting or using cleaning solvents Never release the sprayer lid while the cup is pressurized Industrial applications must follow OSHA requirements Never point a spray gun at a person or animal Serious injury could occur Spraying hazardous materials may result in serious injury or death Do not spray pesticides acids corrosive materials fertilizers an
13. d toxic chemicals WARNING The brass components of this product contain lead a chemical known to the State of California to cause birth defects or other reproductive harm California Health amp Safety Code 25249 5 et seq Note Performance of the compressor if powered by line voltage may vary depending on variations in local line voltage Extension cord usage may also affect tool perfor mance WARNING The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be under stood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SKU 93974 For technical questions please call 1 800 444 3353 Page 4 Unpacking When unpacking check to make sure the parts listed on pages 14 and 16 are included If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual as soon as possible Air Connection Air Hose Line Valve 7 Filter Spray Gun wi 1 4 NPS Recommended Air Line Components AIR 1 COMPRESSOR Air Hose on Reel Regulator For best service you should incorporate a regulator and inline filter as shown in the diagram above Hoses couplers regulators and filters are all available at Harbor Freight Tools Note Compressor pumps discharge condensed water oil or other con
14. e 6 Preparation IMPORTANT Before using for the first time the spray gun must be cleaned using a solvent based thinner If not removed the red oil used by the manufacturer for testing and corrosion protection may contaminate paint IMPORTANT The Spray Gun must be cleaned immediately after use Improper cleaning is a common reason for the Spray Gun not to work Note Proper paint material mixture helps to ensure less problems Be sure to follow the manufacturer s directions Most materials will spray readily if they are thinned properly General tips for Preparation 1 Mix and thin the paint materials thoroughly according to the manufacturer s directions 2 Carefully strain the paint material through a paint strainer or piece of cheese cloth Swing the Cup Locking Lever 44 or 35a out of the locked position to remove the Cup 47 or 34a from the Unit Fill the Cup 47 or 34a to approximately 3 4 full Place the Cup 47 or 34a back on the unit and swing the Cup Locking Lever 44 or 35a to the locked position 4 Start the air compressor To adjust the spray pattern set up a piece of scrap material to practice on While practicing on the scrap material check to see that the material you are spraying has the appropriate consistency If it appears to thin add a very small amount of thinner not included BE CAREFUL when thinning Proceed slowly adding very minimal amounts NEVER exceed the manufacturer s thinning recommenda
15. e in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using tool basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using this tool 1 Keep work area clean Cluttered areas invite injuries 2 Observe work area conditions Do not use these tools in damp or wet locations Don t expose to rain Keep work area well lighted Do not use electrically powered compressors in the presence of flammable gases or liquids 3 Keep children away Children must never be allowed in the work area Do not let them handle machines tools extension cords paint or air hoses 4 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children 5 Use the right tool for the job Do not attempt to force a small tool or attachment to do the work of a larger industrial tool There are certain applications for which this tool was designed It will do the job better and more safely at the rate for which it was intended Do not modify this tool and do not use this tool for a purpose for which it was not intended 6 Dress properly Protective electrically non conductive clothes and non skid footwear are recommended when working Wear restrictive hair covering to contain long hair T Use eye protection Always wear ANSI approved impact safety gog
16. gles Wear an ANSI approved dust mask or respirator when working around chemical dusts paints and mists 8 Do not overreach Keep proper footing and balance at all times Do not reach over or across running machines or air hoses SKU 93974 For technical questions please call 1 800 444 3353 Page 2 10 11 12 13 14 15 16 17 18 19 20 Maintain tools with care Keep tools clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect tool cords and air hoses periodically and if damaged have them repaired by an authorized technician The handles must be kept clean dry and free from oil and grease at all times Disconnect air supply Disconnect air hose when not in use Remove adjusting keys and wrenches Check that keys and adjusting wrenches are removed from the tool before connecting it to the air source Avoid unintentional starting Be sure the trigger is in the Off position when not in use and before attaching to the air source Do not carry any tool with your finger on the trigger whether it is attached to the air compressor or not Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of m
17. n making it difficult to clean SKU 93974 For technical questions please call 1 800 444 3353 Page 11 IMPORTANT The Spray Gun must be cleaned IMMEDIATELY after use Improper cleaning is a common reason for the Spray Gun not to work properly Materials dry quickly which will render the gun useless It is extremely difficult to remove dry paint from small passages within the Gun Maintenance SOLVENT SELECTION Always follow the paint manufacturer s recommendations for cleaning solvent type and disposing of used solvent Latex Paints Use warm soapy water IMPORTANT Do not use mineral spirits on latex paints or the mixture will congeal making it very difficult to remove Oil Based Paints Use mineral spirits IF A FLAMMABLE SOLVENT NEEDS TO BE USED ADHERE TO THE FOLLOWING 1 Follow all of the solvent manufacturer s clean up instructions and safety precautions at all times Always flush the Spray Gun a full hose length from the air compressor If collecting flushed solvents into a metal container transfer into a larger nonmetal container and flush the metal container Work far away from any ignition sources in a vapor free area After each use Ase Empty the Paint Cup and clean it with the solvent 2 Fill the Paint Cup with solvent and spray it through the Gun into a container while shaking the gun Once the Paint Cup is empty repeat the process until the solvent comes out clean
18. oving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Do not use the tool if any trigger does not operate properly Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools Do not operate tool if under the influence of alcohol or drugs Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs If there is any doubt do not operate the tool Use proper size and type extension cord If an extension cord is required for the compressor it must be of the proper size and type to supply the correct current to the compressor without heating up Otherwise the extension cord could melt and catch fire or cause electrical damage to the compressor Check your compressor s manual for the appropriate size cord Maintenance For your safety maintenance should be performed regularly by a qualified technician and the unit must be thoroughly cleaned out after every use Improper cleaning of the Spray Gun is a common reason for the Spray Gun to jam or not perform properly Compressed air only Never use combustible gas as a power source Never excee
19. taminants along with the compressed air Condensation cause fish eyes to appear in paint patterns To avoid this problem install water oil removal filters and controls not included as close to the Spray Gun as possible If run through the Gun water and oil will cause damage 1 You will need to prepare a 1 4 air connector to connect to the air inlet on either the Large or Small Sprayers First wrap the Air Inlet 40 or 23a shown on next page with pipe thread seal tape before threading it into the 1 4 air connector Connect the 1 4 ID Air Source Hose to the Spray Gun 2 Set the air pressure on your compressor to the recommended pressure for the spray gun used as mentioned on page 2 Do not exceed the maximum recommended air pressure of 40 PSI for the large gun and small gun 3 Check the air connection for leaks and then disconnect the tool from the air source Note This unit comes with a 1 4 18 NPS IN OUT x 25 Recoil Air Hose which you may use to connect from the air inlet to the air hose compressor to give you more flexibility SKU 93974 For technical questions please call 1 800 444 3353 Page 5 Small Spray Gun Air Inlet 23a Fluid Control Knob 28a Air Cap 1a Paint Cup 34a Pe OEN Figure 1 Large Spray Gun Pattern Control Knob 13 Air Cap Set 1S Trigger 38 Fluid Control Knob 29 Air Inlet 40 Cup 47 SKU 93974 For technical questions please call 1 800 444 3353 Pag
20. tions SKU 93974 For technical questions please call 1 800 444 3353 Page 7 Fan Direction and Pattern Adjustment Note Always make sure the Vent 48 on the large spray gun is clear and unclogged Fan Direction To change the direction of the fan from horizontal to vertical loosen the Lock Ring and turn the Air Cap 1 or 1a 90 degrees After the adjustment tighten the Lock Ring by hand See FIGURE 2 below Lock Ring Horizontal Fan FIGURE 2 Vertical Fan Pattern Adjustment Warning Never exceed the Maximum Inlet PSI of 40 PSI 1 If you need to reduce the air pressure for specific areas adjust the air compressor 2 To set the pattern size specific to the job use the Pattern Control Knob 12a or 13 see FIGURE 1 on page 6 By turning it counterclockwise all the way open the pattern will flatten Turn the Pattern Control Knob clockwise for a round pattern See FIGURE 3 below FIGURE 3 9 O FlatOpen lt Q Round Closed SKU 93974 For technical questions please call 1 800 444 3353 Page 8 Fan Direction and Pattern Adjustment continued 3 Turn the Fluid Control Knob 28a or 29 clockwise until it is fully closed See FIGURE 1 on page 6 4 After setting up a piece of scrap material squeeze the Trigger in short bursts while turning the Fluid Control Knob counterclockwise and observe the spray patterns until you see the pattern you want Also look at the pattern for consistency Too much air
21. ve Nut 1 S Cup Locks Nozzle Assembly AD me od or Stem Assembly g s Volume Adjustment Assy Spring 24 S Needle Assembly For technical questions please call 1 800 444 3353 Page 16 Warranty Card gt LN YD LV VY LNW Y LN YD AN YD ay DY V IN CENTRAL x gt l RY ZA gt EA A PNEUMATIC LIMITED 1 YEAR i TA o WD H N WARRANTY R SY NY D ZA VIS CH Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards ya KN and warrants to the original purchaser that this product is free from defects in materials and workmanship for A N the period of one year from the date of purchase This warranty does not apply to damage due directly or Nes AN indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities or to lack of WX D maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent Ka A special or consequential damages arising from the use of our product Some states do not allow the exclusion Y DX ZO or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to WZ ey you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED S gt KY INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS
Download Pdf Manuals
Related Search