Harbor Freight Tools 93601 User's Manual
Contents
1. 6 over the Flexible Hose Slide the Flexible Hose 1 onto the dust port Slide the Wire Hose Clamp 6 so that it sits on both a section of Flexible Hose 1 and the dust port Thread down the screw on the Wire Hose Clamp 6 until the Flexible Hose 1 is tight on the dust port Open and close the Blast Gate 2 to control the air flow from the Power Tool s to the dust collector When this kit is attached to 2 power tools always close the Blast Gate 2 of an unused dust collector hose SKU 93601 For technical questions please call 1 800 444 3353 Page 4 Inspection Maintenance and Cleaning CAUTION Prior to performing any inspection maintenance or cleaning of the Dust Collector Accessory Kit make sure to turn OFF and then disconnect the power tool from the outlet BEFORE EACH USE inspect the general condition of the Dust Collector Accessory Kit Check for loose connections misalignment or binding of moving parts cracked torn or broken parts and any other condition that may affect its safe operation If abnormal noise or vibration occurs have the problem corrected before further use Do not use damaged equipment 3 DAILY With a soft brush cloth or vacuum remove all debris from the Dust Collector Accessory Kit If necessary you may use a mild detergent 4 Clean the hoses periodically by standing it on end and tapping it to remove dust and debris PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIB2. CENTRAL MACHINERY DUST COLLECTOR ACCESSORY KIT 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web Site at www harborfreight com Copyright 2005 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 THANK YOU for choosing a HARBOR FREIGHT TOOLS product For future reference please complete the owner s record below Model Serial No Purchase Date SAVE THE RECEIPT WARRANTY AND THESE INSTRUCTIONS It is important that you read the entire manual to become familiar with the unit BEFORE you begin assembly Technical Specifications Material ABS Thermoplastic low carbon steel clamps ply vinyl flex hose Hose Dimensions 2 4 diameter x 10 Also included 1 Table Saw Hood 12 square 1 Y Connector 2 Blast Gates 2 Jointer Hoods 6 square 10 Wire Hose Clamps Weight 13 Lbs IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT Safety Warnings and Precautions WARNING When using product basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using this product 1 Keep work area clean Cluttered areas invite injuries 2 Observe work area conditions
3. Keep work area well lighted 3 Store idle equipment When not in use the Dust Collector Accessory Kit must be stored in a safe and dry location to inhibit rust Always lock up products and keep out of reach of children 4 Use the right product for the job There are certain applications for which the Dust Collector Accessory Kit was designed Do not modify the Accessory Kit and do not use this product for a purpose for which it was not intended 5 Check for damaged parts Before using any product any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for any broken or damaged parts and any other conditions that may affect its operation Replace or repair damaged or worn parts immediately 6 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty 7 Do not operate product if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the product 8 Use eye and ear protection Always wear ANSI approved impact safety goggles Wear a full face shield if you are producing metal filings and wood chips Wear an ANSI approved dust mask or respirator when working around metal wood and chemical dusts and mists 9 Do not place the Hoses in walkways or i
4. UTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Parts List Part Description Quantity 1 Flexible Hose 4 x 10 2 2 Blast Gate 4 x 4 2 3 Jointer Hood 6 2 4 Y Fitting 4 x 4 x 4 1 5 Table Saw Dust Hood 12 x 12 1 6 Wire Hose Clamp 10 Parts Diagram PEAN 3 4 A a f a 5 ol DS F i a r y M M VA P ZC N MN 4 I f SKU 93601 For technical questions please call 1 800 444 3353 Page 5
5. ery to which the Dust Collector Accessory Kit may be attached it is recommended that only a qualified technician perform the assembly procedure SKU 93601 For technical questions please call 1 800 444 3353 Page 3 Assembly Though the Dust Collector Accessory Kit is designed to offer a wide variety of applications the following illustration depicts a typical assembly method to hook up one power equipment tool and two power equipment tools see Figure 1 below Note The Dust Collector Accessory Kit is designed to be attached to stationary power equipment tools and dust collectors having 4 diameter dust ports Depending on the diameter of the dust port of your power equipment tools and dust collector it may be necessary to attach size adapters not included to ensure a proper fit Figure 1 To Attach to One or Two Power Tools Attaching to One Power Tool Jointer Hood 6 square 3 a or 4 Diameter Blast Gate 2 Table Saw Dust Hood 12 square 5 4 Wire Hose Clamp 6 Beene ere fal 2 Flexible Hose 1 Collector Attaching to Two Power Tools Y Fitting 4 Check the length of Flexible Hose 1 needed to set up the Dust Collector Accessory Kit with your power tool It may be necessary to cut the Flexible Hose 1 To cut the Flexible Hose 1 cut the plastic on the hose in a straight line between one coil of wire Use a tin snip or wire cutter to cut the coil inside the hose Place a Wire Hose Clamp
6. hemicals are Lead from lead based paints Crystalline silica from bricks and cement or other masonry products Arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles California Health amp Safety Code 25249 5 et seq Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Unpacking When unpacking your Dust Collector Accessory Kit check to make sure all parts listed on page 5 are included If any parts are missing or broken please call HARBOR FREIGHT TOOLS at 1 800 444 3353 Product Overview The Dust Collector Accessory Kit is designed to be attached to one or two power tools and is used for the collection of wood dust wood chips sand and other light debris The Dust Collector Accessory Kit may be attached to table saws band saws sanders router tables shapers jointers and a variety of dust collecting machines all having a 4 dust port Due to the wide diversity of power machin
7. n any trafficked location Set up the Dust Collector Accessory Kit in a location where people or vehicles will not trip or run over the hoses SKU 93601 For technical questions please call 1 800 444 3353 Page 2 10 Always check hardware and assembled parts after assembling All connections should be tight and hardware tightened 11 Caution Avoid sharp edges during use and assembly 12 Beware of operating the power tool in explosive atmospheres such as in the presence of flammable liquids gases or sawdust Electrical products create sparks which may ignite sawdust released from the Dust Collector as well as other dust and fumes 13 Carefully inspect the condition of the accessory before use and check the accessory continually during use If any damage is noted stop immediately and replace the accessory with an undamaged one Harbor Freight Tools cannot be held responsible for damage caused by using a damaged accessory on this product 14 Keep the hoses away from sharp objects and excessive heat 15 Make sure to read and understand all instructions and safety precautions as outlined in the manufacturers manual of the power equipment to which the Dust Collector Accessory Kit will be attached WARNING Some dust created by power sanding sawing grinding drilling and other construction activites contain chemicals known to the State of California to cause cancer birth defects or other reproductive harm some examples of these c
Download Pdf Manuals
Related Search