Harbor Freight Tools 93496 User's Manual
Contents
1. CENTRAL PNEUMATIC Air Palm Nailer Mee 3193496 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com Copyright 2005 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Specifications Cast Aluminum Frame hi Construction Steel Air Inlet and Magnetic ver wall eenguiang a 8 gauge l Gauge nails not included Steel Nail Holder l l Driver Stroke and 1 4 stroke 1 7 I Air Inlet Dimensions 1 4 18NPT Female Inlet Impacts per Minute 1 000 Blows Per Minute Air Consumption Operating Air Pressure 70 125psi Overall Dimensions 3 W x 4 L x 5 14 H Net Weight 2 65 Lbs The air pressure setting must not exceed job site regulations restrictions The air pressure setting must not exceed 90 PSI when being used with work pieces that have a thickness of less than 1 3 4 Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for fut2. If you do not use a filter and in line oiler put a few drops of water displacement oil into the air line before each use After each use the Air Hand Nailer should be carefully drained of collected moisture and sprayed with a water displacement oil We recommend that you install a quick release nipple not included into the Air Inlet 23 Quick release connectors at all points in an air pressure system make your work easier Air Hose Line Valve Oiler G7 Filter AiR COMPRESSOR Air Palm f _ _ SL Nailer j 6 eb o Recommended Air Line Components Unpacking Air Hose on Reel Regulator When unpacking check to make sure the following parts are included Air Palm Nailer Tool Leather Cover 1 4mm Hex Key If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual REV 11 06 SKU 93496 For technical questions please call 1 800 444 3353 Page 5 Operation NOTE This tool is assembled when you receive it and may be used immediately However we recommend that you install a quick disconnect adapter not included to the Air Inlet 23 before use WARNING Do not put a nail into the Air Palm Nailer until you are ready to work WARNING Do not point the Air Palm Nailer toward any person or animal Severe injury may result in case of accidental ejection of a nail 1 Attach the air supply hose not included to the tool 2 Grip the base of the tool in o
3. TION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 93496 For technical questions please call 1 800 444 3353 Page 8
4. d based paints Crystalline silica from bricks and cement or other masonry products Arsenic and chromium from chemically treated lumber California Health amp Safety Code 25249 5 et seq WARNING The Brass components of this product contain Lead a chemical known to the state of California to cause birth defects or other reproductive harm Calif Health amp Safety Code 25545 5 et seq REV 11 06 SKU 93496 For technical questions please call 1 800 444 3353 Page 4 Warning The warnings cautions and instructions discussed in this instruc tion manual cannot cover all possible conditions and situations that may oc cur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Air Pressure Supply This tool is designed to operate with a maximum air pressure of 125 psi You must use an air regulator set at 125 psi or below Note Performance of this tool may vary depending on variations in local air pressure In use this tool will use 2 4 Cubic Feet per Minute of compressed air at 125 psi For satisfactory performance you must use an air compressor capable of deliver ing this volume of air at the stated pressure We recommend that you use both a filter and an in line oiler in your air Supply system as illustrated in the diagram below These components are not included with this tool but are available from Harbor Freight Tools
5. e tool and spray a small amount of water displacing oil into and on the tool Wipe clean 3 Store tool in a safe location out of reach of children and unauthorized persons Troubleshooting Tool will not operate 1 Possible cause Low or no air pressure Solution Check air compressor to be sure it is operating properly Check Air Regulator Check air lines for leaking or blockage 2 Possible cause Corroded Piston 8 Solution Spray light weight penetrating oil into the Air Inlet 23 If tool still won t operate take it to a qualified service technician for repair 3 Possible Cause Damaged Seals or O rings Solution Take it to a qualified service technician for repair Note A hex wrench is included for removing hex bolts when removing the Rear Cover 18 This work should only be done by a qualified service technician Parts List rs ra 10 fore n fors r2 omma 13 Gyinder Cover ra Rear Cover 19 Vane Packing forme a Joas o fie ok 2 farne 2a Hexwrerch 23 Leamer Cover ot shown ee NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 93496 For technical questions please call 1 800 444 3353 Page 7 Assembly Drawing PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTA
6. ger whether it is attached or not Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Do not use the tool if any switch does not turn On and Off properly Guard against electric shock when working on electrical equipment Prevent body contact with grounded surfaces such as pipes radiators ranges and refrigerator enclosures SKU 93496 For technical questions please call 1 800 444 3353 Page 3 16 17 18 19 20 23 24 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools Do not operate tool if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool Use proper size and type air pressure line and fittings The recomme
7. nded air line for this tool is 3 8 delivering no more than 125 psi Recommended air inlet size is 1 4 18 npt Maintenance For your safety service and maintenance should be performed regularly by a qualified technician Compressed air only Never use combustible gas as a power source 21 Do not put a nail into the Air Palm Nailer until you are ready to work Do not point the Air Nailer toward any person or animal Severe injury may result in case of accidental ejection of a nail 22 Disconnect air supply when done working Before storing or making any adjustments to the Nailer make sure that the compressed air is disconnected Fire fasteners into an appropriate work surface only Do not attempt to fire fasteners into surfaces too hard to penetrate Do not drive fasteners on top of other fasteners or at too steep of an angle Fasteners can ricochet causing personal injury Never fire the Nailer into the air or point it toward yourself or another person Always wear ANSI approved safety goggles during use maintenance and reloading Do not fire fasteners too close to the edge of a workpiece They may split the workpiece and fly free causing personal injury WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contain chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lea
8. ne hand Note that there is a hand strap and thumb strap on the Leather Cover 25 to facilitate holding the tool CAUTION Whenever using this tool wear ANSI approved safety goggles 3 When ready to work hold a nail by the shaft and place the flat head into the Hammer Tip 3 The nail will be held in place by the magnetic tip 4 Place the pointed end of the nail where desired on the workpiece Keep your free hand away from the tool and the nail 5 Press the tool straight down This will trigger the tool and cause it to hammer the nail Continue pressing down until the nail is driven all the way in 6 You can adjust the force of the tool s impact by adjusting the air pressure However do not operate the tool at more than 125 psi CAUTION Disconnect the tool from air pressure supply when not in use and before making any adjustments 7 During operation the Hammer Tip will hammer 1 4 up to 1 000 times per minute This tool is useful for driving nails in tight areas where a full sized air nail gun may not reach 8 When the nail is hammered all the way down the tool will stop operating To stop the tool release the downward pressure on the Hammer Tip REV 11 06 SKU 93496 For technical questions please call 1 800 444 3353 Page 6 Maintenance 1 Place afew drops of light weight air tool oil not included into the Air Inlet 23 each time before using the tool 2 After each use drain any accumulated moisture from th
9. onductive work clothes and non skid footwear are recommended when working Wear restrictive hair covering to contain long hair Always wear work boots and work gloves 7 Use eye and ear protection Always wear ANSI approved impact safety goggles Wear a full face shield if you are producing metal filings or wood chips Wear an ANSI approved dust mask or respirator when working around metal wood and chemical dusts and mists 8 Do not overreach Keep proper footing and balance at all times Do not reach over or across running machines Maintain tools with care Keep tools clean and in good condition for better and safer performance Follow instructions for lubricating and changing accessories Inspect tool fittings and hoses periodically and if damaged have them repaired by an authorized technician The handles must be kept clean dry and free from oil and grease at all times Disconnect Air Hose and release any built up air pressure Never service the Nailer clear jams or disassemble with the air hose attached Always release any built up air even after disconnecting hose Disconnect the Nailer when not in use Remove adjusting keys and wrenches Check that keys and adjusting wrenches are removed from the tool or machine work surface before connecting it Avoid unintentional starting Be sure the switch is in the Off position when not in use and before attaching to pressure source Do not carry any tool with your finger on the trig
10. ure reference Safety Warnings and Precautions Read all instructions before using this tool WARNING When using tool basic safety precautions should al ways be followed to reduce the risk of personal injury and dam age to equipment 1 Keep work area clean Cluttered areas invite injuries 2 Observe work area conditions Do not use machines or power tools such as air compressor in damp or wet locations Do not expose to rain Keep work area well lit Do not use electrically powered tools in the presence of flammable gases or liquids 3 Keep children away Children must never be allowed in the work area Do not let them handle machines tools or extension cords 4 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children 5 Use the right tool for the job Do not attempt to force a small tool or attachment to do the work of a larger industrial tool There are certain applications for which this tool was designed It will do the job better and more safely at the rate for which it was intended Do not modify this tool and do not use this tool for a purpose for which it was not intended REV 11 06 SKU 93496 For technical questions please call 1 800 444 3353 Page 2 10 11 12 13 14 15 Dress properly while working Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically non c
Download Pdf Manuals
Related Search