Harbor Freight Tools 92188 User's Manual
Contents
1. ITEM 92188 Angle Drill With Keyless Chuck Operating Instructions 3491 Mission Oaks Blvd Camarillo CA 93011 Distributed exclusively by Harbor Freight Tools Copyright 2004 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Thank you for choosing a Harbor Freight Tools product For future reference please com plete the owner s record below Model Purchase Date Save the receipt and these instructions It is important that you read the entire instruction sheet to become familiar with this product before you begin using it Technical Specifications Angle Drill includes 3 8 Shaft Attachment Spindle Thread 3 8 24 Hex Shaft Size 5 16 Maximum Speed 6000 RPM A Safety Warnings and Precautions WARNING When using tool basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using this product 1 Do not exceed 6 000 RPM maximum speed Avoid working alone If accident happens an assistant can bring help Keep work area clean Cluttered areas invite injuries Keep children away Children must never be allowed in the work area Do not let them handle chines tools or ex2. UALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THE ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 92188 For technical questions please call 1 800 444 3353 Page 4
3. itch does not turn On and Off properly 12 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty 13 Do not operate tool if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool 14 Use proper size and type extension cord If an extension cord is required it must be of the proper size and type to supply the correct current to the tool without heating up Otherwise the extension cord could melt and catch fire or cause electrical damage to the tool This tool requires use of an extension cord of 0 to 10 amps capability up to 50 feet with wire size rated at 18 AWG Longer extension cords require larger size wire If you are using the tool outdoors use an extension cord rated for outdoor use signified by the jacket 15 Take caution as some woods contain preservatives such as copper chromium arsenate CCA which can be toxic When drilling these materials extra care should be taken to avoid inhalation and minimize skin contact 16 Maintenance For your safety maintenance should be performed regularly by a qualified technician 17 Read and understand all warnings and instructions provided in the instruction manual of the drill being used to power this Angle Drill attachment Warning The warnings ca
4. nd test its operation Make sure the Angle Drill is properly aligned for maximum leverage Check that the drill bit is properly inserted 6 The Angle Drill is now ready to be used Align the drill bit on the workpiece While firmly holding the power drill and the Angle Drill turn on the power drill and begin drilling Caution Always unplug the power drill or disconnect the air hose on air powered drills before changing bits or making adjustments to the Angle Drill Parts List Description Needle Bearing Spindle Case1 Clutch Pin Ball Bearing Bevel Gear Ball Bearing Angle Head Key Bevel Gear Bearing Cap Chuck Casing Chuck Screw Shaft 1 2 3 4 5 6 8 9 Note Some parts listed and shown for illustration purposes only and not available individually as replacement parts SKU 92188 For technical questions please call 1 800 444 3353 Page 3 Parts Diagram GO Oo La MSS Sy 9 sim SOE R os A 5 AES EE ANS v f SSS SIS PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS Q
5. tension cords REV 09b Safety Warnings and Precautions continued 5 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children 6 Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protec tive electrically nonconductive clothes and nonskid footwear are recommended when working Wear restrictive hair covering to contain long hair 7 Use eye and ear protection Always wear ANSI approved impact safety goggles 8 Do overreach Keep proper footing and balance at all times 9 Use the right tool for the job Do not attempt to force a small tool or attachment to do the work of a larger industrial tool There are certain applications for which this tool was designed Do not modify this tool and do not use this tool for a purpose for which it was not intended 10 Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired 11 Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Do not use the tool if any sw
6. utions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that com mon sense and caution are factors which cannot be built into this product but must be supplied by the operator Unpacking When unpacking verify against the Parts List and Parts Diagram on the next page that all parts are included If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual SKU 92188 For technical questions please call 1 800 444 3353 Page 2 and Operating the Angle Drill Unplug the electric drill or disconnect the air hose on the air powered drill before attempting to attach the Angle Drill The drill used to power the Angle Drill should also be turned OFF 2 Insert the Shaft 13 of the Angle Drill into the chuck of the drill being used to power this attachment Properly align and tighten the Shaft in place read instructions provided with the drill being used to power this attachment 3 Insert the bit of choice into the Chuck Casing 12 of the Angle Drill and tighten in place the chuck is keyless 4 Properly grip the Drill Angle Drill Attachment One hand will operate the power drill and the other hand will wraparound the Spindle Case 2 of the Angle Drill attachment to support the tool while it is being used 5 Before using the Angle Drill on the workpiece turn on the drill a
Download Pdf Manuals
Related Search