Harbor Freight Tools 8 Channel Surveillance DVR with 4 Cameras and Mobile Monitoring Capabilities Product manual
Contents
1. Figure AM Item 61229 For technical questions please call 1 800 444 3353 Page 27 Local Area Network LAN Setup Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Note This setup allows you to connect to the DVR through the Internet within your home network This setup requires the use of a Windows PC sold separately with Internet Explorer an Ethernet Cable sold separately and a Router sold separately Network gt Network Use the chart below to record the information you will need to set up your LAN New DVR IP Address DVR s LAN Address Figure AN d Write the New DVR IP Address Display NEk Euverem EmaNmowie oons in the chart above FS a Record HCE om 8 a 4 On DVR go to Network gt Network a Change Type to Static i b Change Client Port to 3000 c Change HTTP Port to 3001 d Change IP Address to the New DVR Dera MRR ERT IP Address from the chart Figure AO e Change Subnet Mask and Default Gateway to the ones from the chart 1 Connect DVR to Router via Ethernet Cable f Change DNS1 to be the same as Gateway 2 OnPC go to Start menu then click Run g Click Apply then Exit DVR will a Type cmd then click OK A prompt restart Click OK DOS window will open a bee 5 After restart go back to Network gt b Type ipconfig then press2. Replay Time be GTECECOCCRILELCE M release fz 00 ot 02 03 04 05 oe oo tof v1 v2 19 14 16 Pe 17 18 19 20 21 22 29 Figure AC Search Click to populate Record State table Click to play selected recording Month shows all days in selected month where there are recordings Record State Green Normal recording Red Motion Detection recording Date Shows all hours in selected day where there are recordings Evant Search Go to Event Search See Backup Recordings section Figure AD Search by Date 1 Search Date Enter desired search date and click Search to populate table a Click on box for date to search b Click on box for hour to search This will bring up the channel list 2 Select Channel s Click on box es for channel s to view then click Play 3 The Playback Control Bar will pop up on bottom of screen Item 61229 For technical questions please call 1 800 444 3353 Note The Playback Control Bar will automatically disappear when the mouse stops moving To recall Playback Control Bar move the mouse Figure AE C aa Rewind xax OOOO gt Play 172 114 118 speed gt Playnormal speed TS gt gt Fast Forward X 4X 6X IX Volume Control Exit recording Figure AF Control volume if audio hooked up To exit recording click X on Playback Control Bar then click Exit to return to Record Search Search by Time To
3. including all text under subheadings therein before set up or use of this product This setup allows you to connect to the DVR from a remote computer or smartphone This is an advanced setup You may need to consult your Router s Manual and or call the manufacturer or Internet Service Provider for instructions on Port Forwarding 1 Set up Local Area Network first 2 Open Internet Explorer and type the Default Gateway Router s IP Address in the address bar and press Enter This will bring up your Router s Log in 3 Login to your Router and check your connection type a If Static the IP Address will not change and your connection will remain stable Proceed to Port Forwarding b If DHCP the IP Address will change at some point in time When it changes you will then need to use the new IP Address to connect to the DVR Other options are Contact your ISP and request a Static IP Address for which there may be a charge e Set up a Dynamic Domain Naming System This is outside the scope of this manual Settings can be accessed on the Network gt DDNS tab 4 Go to Port Forwarding or Applications and Gaming 5 Set start port to 3000 and end port to 3002 Set up both UDP and TCP protocols if the option is given 6 Open Internet Explorer and type in the Router s IP Address and HTTP Port a http XX XXX XXX XXX yyyy where x IP Address and y HTTP Port This is the DVR s Public IP Address writ
4. 2 Use supplied Power Adapter only 3 Do not expose the Power Adapter to rain or wet conditions Water entering the Power Adapter will increase the risk of electric shock Item 61229 Do not abuse the Power Adapter cord Never use the cord for unplugging the plug from the outlet Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock Handle Camera with care Camera could be damaged by improper handling or storage For technical questions please call 1 800 444 3353 Page 3 wn gt m m j lt DVR Safety Warnings 1 Maintain adequate airflow around DVR 5 Maintain labels and nameplates on the unit l These carry important safety information If 2 Use supplied Power Adapter only unreadable or missing contact Harbor 3 Do not expose the Power Adapter or DVR Poegi TOn Or A Teplacemenk console to rain or wet conditions Water 6 WARNING Handling the cord on this product will entering the Power Adapter or DVR console expose you to lead a chemical known to the State will increase the risk of electric shock of California to cause cancer and birth defects or other reproductive harm Wash hands after handling 4 Do not abuse the Power Adapter cord Never California Health amp Safety Code 25249 5 et seq use the cord for unplugging the plug from the outlet Keep cord away from heat oil sharp 7 The warnings precautions and instruct
5. Cables CAUTION Route the Cables so as to avoid a tripping hazard b Choose locations high enough so that they are out of reach of children but still cover the desired viewing areas E Mount Cameras Using the Base as a template mark locations of mounting holes on mounting surface Note Route Cable through slot on Base to keep Base flush with mounting surface while marking holes Solid Surface c Verify that installation surfaces have no hidden utility lines before drilling or driving screws d To avoid mounting the Cameras upside down make sure the Hood is above the Lens e Make sure no strong light will shine directly into Camera Lenses Mounting Holes Cable Slot Figure F 1 Using a drill bit slightly smaller than the Screws drill pilot holes into the marked locations 2 Position Camera so that mounting holes align with pilot holes Hollow Surface Note Route Cable through slot on Base to keep Base flush with mounting surface 3 Drive Screws through mounting holes in Base and into pilot holes until the Camera is securely attached to the mounting surface 1 Using a drill bit slightly smaller than the Anchors drill holes in the marked locations 2 Tap Anchors into the holes until they are almost flush with mounting surface 3 Position Camera so that mounting holes align with anchors Camera Adjustment 1 Loosen Adjustment Wheel rotate Camera as needed then tighten A
6. Enter Network to view the settings c You will see the Local Area Connection of the Router 6 Open Internet Explorer and type in the IP Address and HTTP Port in the address bar d In the chart above write down the numbers corresponding to a http xxx xxx xxx xxx 3001 where x IP Address and 3001 HTTP Port e Subnet Mask Write this address on chart under e Default Gateway Router s IP Address DVR s LAN Address 3 Create a New DVR IP Address b Press Enter a Iflast 3 digits of Default Gateway c Allow ActiveX control to install z are 0 99 change last 3 digits to a Note Youm i y need to adjust the settings in m number between 100 and 255 Internet Explorer by adding the http address to b If last 3 digits of Default Gateway are Trusted Sites and modifying ActiveX controls re 100 or more change last 3 digits to a pa number between 200 and 255 7 After ActiveX Control installs Log in to DVR x f using User DVR s User Name and Password c New DVR IP Address will be xxx xxx xxx yyy where x first 3 sets of current Default 8 The DVR can now be controlled by a Gateway Router s IP Address and computer in your home network y new set created in 3 a or b Page 28 For technical questions please call 1 800 444 3353 Item 61229 Set up Remote Video Stream Network gt SubStream Select channels to export through network connection Set up Email Capability Network gt Email Net
7. For technical questions please call 1 800 444 3353 Page 9 Click Apply Main Menu and Password then OK In DVR Set User Name Select System Do you have a Windows PC with Connect DVR to Internet Explorer Router via and a Router Ethernet Cable Sold Separately STOP Ensure you have a Windows PC with Internet Explorer and a Router before proceeding N m cs Z 7 7 On PC go to Start Find the Router s LAN From DVR Main Men i u Menu click Run Write down select In DOS window 1 Subnet Mask Network gt Network type cmd click OK 2 Default Gateway Type Static type ipconfig Router s IP Address press ENTER Change last 3 digits to a number between Create New IP 200 and 255 Address Are last 3 digits of Default Gateway between 0 99 In DVR Network gt Network change settings 1 Client Port 3000 2 HTTP Port 3001 3 New IP Address 4 Subnet Mask you wrote down Change last 3 digits 5 Default Gateway you wrote down to a number between 6 DNS1 same as Gateway 100 and 255 Open Internet Explorer Click Apply then OK After restart In address bar type in o save changes on DVR go to DVR s IP Address and HTTP Port Glick Exit DYR will prompt Network gt Network http xxx xxx xxx xxx 3001 restart Click OK to view settings where x IP Address and 3001 HTTP Port Press Enter Allow ActiveX Control to install You may
8. Lock a Password Enter Password must be 6 numbers b Confirm Enter Password again to confirm Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes Set up additional Users 4 Select user then click Edit 5 User Enable Select Enable 6 User Name Enter User Name up to 8 characters 7 Password Enable Select Enable or Disable a Password Enter Password must be 6 numbers b Confirm Enter Password again to confirm Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes Page 20 For technical questions plea Select User that was just named and click Permission a Click in boxes to select specific permissions b Click All to select all permissions c Click Clear to remove all permissions SYSTEM General Users Version USER NAME 2 log Search Parameter Maintain Disk Manage Remote Login KA Rotate Control Z Manual Record Backup ial Figure Q Log Search Check entire system log Set all parameters Update version recover factory presets reboot and shut down Manage Hard Drives Disk Manage including deleting data Remote Login Log in remotely Rotate Control Manage Sequence Manual Backup recordings of selected channels View live images of Live selected channels Playback Playback recordings of select channels Perform PTZ o
9. Record Select Enable or Disable discard unsaved changes 3 Pack Duration Select continuous recording time for each pack recording segment Video Stream Record gt MainStream Set Resolution Frames Per Second Bitrate Audio 1 Resolution Select CIF D1 or HD1 ae 2 Fps Frames per second Set as desired 3 Bitrate Kbps Set as desired or ome aes o A Bre Pate 4 Audio Check box to record audio if microphone pepa E e sold separately has been connected etre tet et This is only available on Channel 1 5 Copy Copy parameters from one Figure Y caw Se CIF 352X240 224 768 HDI 704x240 80 448 D1 704x480 80 448 Figure Z Item 61229 For technical questions please call 1 800 444 3353 Channel to other Channels a Select Channel to copy from b Select Channel to copy to or select ALL c Click Copy then click OK Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes Page 23 Maintain Hard Drive Advanced gt Maintain Set up Reboot Cycle Update Software Manually b Every Week Enter day of week Restore Default Settings Reboot And Shut Down and time for reboot ADVANCED c Every Month Enter day of month and time for reboot a E oo 3 Update Used for updating firmware using a USB drive Do not update firmware ae Tose Dean Rabe SAAD SNA unless device is not working properly and Customer Service i
10. changes 2 Name Set Channel name up to 8 characters 8 Copy Copy parameters from one 3 Position Select position where Channel Name will appear on the screen a U L Upper Left b D L Lower Left c U R Upper Right d D R Lower Right e Close No name will appear 4 Color Click Setup to adjust Hue Brightness Contrast and Saturation Item 61229 For technical questions please call 1 800 444 3353 Channel to other Channels a Select Channel to copy from b Select Channel to copy to or select ALL c Click Copy then click OK Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes Page 21 Display Output Display gt Output We Rotate Time pos Transparency Volume Figure U 1 Rotate Time Amount of time in seconds that each Channel will display in Live View when Start SEQ is activated from the Pop Up Menu 2 VGA Resolution Select resolution 3 Init DEV Select Video Output port wn m j Z wn Privacy Zones Display gt Privacy Zone 4 Transparency Select Transparency of the Menus 5 Volume Press Volume button to open Volume Control Volume 4 31 MUTE Figure V a Set Volume if audio hooked up b Check Mute box to turn off sound c Click save icon on right to save settings then click OK d Right click to return to Output Changes wil
11. need to adjust the settings in After ActiveX Control installs Internet Explorer by adding the http Log in to DVR address to Trusted Sites and modifying with User Name and Password ActiveX controls to allow installation Page 10 For technical questions please call 1 800 444 3353 Item 61229 See Page 30 Wide Area Network WAN Setup FOR ADVANCED USERS Internet Setup for Remote Use PORT FORWARDING Set up LAN according to instructions above Open Internet Explorer In address bar type in Default Gateway from LAN Setup above Example XXX XXX XXX XXX Press Enter Set start port to 3000 and end port to 3002 Set up both UDP and TCP protocols if the Log in to the Router and go to Port Forwarding or Applications and Gaming Find the Router s IP Address by going to whatsmyip com SETTINGS tae Write it down option is given On remote computer Open Internet Explorer In address bar type in Router s IP Address CEOE and HTTP Port from LAN Setup above ACCESS http xx xxx xxx xxx 3001 where x IP Address and 3001 HTTP Port Press Enter Allow ActiveX Control to install You may need to adjust the settings in Internet Explorer by adding the http address to Trusted Sites and modifying ActiveX controls to allow installation After ActiveX Control installs Log in to DVR with User Name and Password from LAN Setup above OPERATION In DVR Main Menu SMARTPHONE Select Network ACC
12. t interfere with cracked or broken parts and visibility such as overgrown bushes any other condition that may affect its safe operation Item 61229 For technical questions please call 1 800 444 3353 Page 33 Troubleshooting Possible Causes Likely Solutions Controls stop Lost connection Press REW button on front of DVR until beep sounds working on DVR with DVR 1 Loose or incorrect 1 Check that all connections are secure Monitor does not connections and in the correct location display image 2 Monitor needs 2 Adjust the image settings on the monitor adjustment Poor quality images Setting s are incorrect Adjust settings for Video Stream on page 23 Error codes when __ Incompatibility with Check System Requirements on page Video Client DvrClient trying to install Operating System on page 32 to make sure your Operating System is supported DvrClient software Password not Incorrect password Contact Customer service 1 800 444 3353 working for instructions on resetting password Page 34 For technical questions please call 1 800 444 3353 Item 61229 Parts List Part Description Qty DVR Console 2 Power Adapter 2 Input 100 240V 1 5A Max 50 60 Hz p Qty ze Power Splitter ze 7 Camera Mounting Hardware 1 3 6 mm Lens Camera 10 Output 12VDC 2A BNC to RCA Cable T Remote Control Record Serial Number Here Note If product has no serial number record Note So
13. ESS then Mobile Set User Name Set Mobile Port Click Apply and Password to 3002 then OK Insert supplied CD into computer and look in Mobile Software folder for instructions NETWORK Item 61229 For technical questions please call 1 800 444 3353 DVR Equipment Connections Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Check federal state and local surveillance laws before installing video and or audio surveillance equipment Connect and test all equipment and camera locations before installing cameras Use a surge protector sold separately to protect equipment INITIAL SETUP m Physical Connections C7 Connect Connect Connect Connect Mount d m Monitor Cameras Mouse Power Cameras 9 d2 Video Output A ad fe ad ad Note Monitor and Surge Protector D sold separately Page 12 For technical questions please call 1 800 444 3353 Item 61229 Designate Location for DVR and Monitor When planning location for DVR and Monitor 3 Take into consideration the length of the Camera Cables 1 Choose a clean dry location indoors with a 120V outlet nearby CAUTION Route the Cables so as to avoid a tripping hazard 2 For network viewing make sure the DVR is located close to a router 4 Make sure location will remain within Operating Temper
14. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference Bunker Hill Security 8 Channel Surveillance DVR Visit our website at http www harborfreight com Email our technical support at tech harborfreight com ITEM 61229 When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 800 444 3353 as soon as possible Copyright 2013 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Table of Contents Se reia aaa neces yspadezen en seadecaten ics 3 DVR Operating Instructions 2 Specifications 0 e
15. ables better control in unexpected situations Use Precautions 1 This product is not a toy Do not allow children to play with or near this item 2 Use as intended only 3 Do not modify Electrical Safety 1 Power Adapter plugs must match the outlet Never modify the plug in any way Unmodified plugs and matching outlets will reduce risk of electric shock 2 Do not expose DVR unit to rain or wet conditions Water entering the DVR will increase the risk of electric shock Service Wear ANSI approved safety goggles during installation Keep installation area clean and well lit Keep children and bystanders out of the area during installation SAFETY Do not install when tired or when under the influence of alcohol drugs or medication Maintain product labels and nameplates These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock Have your DVR equipment serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the equipment is maintained Camera Safety Warnings 1 To prevent electric shock do not attempt to disassemble Camera There are no serviceable parts inside
16. ase call 1 800 444 3353 Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes 7 NTP Network Time Protocol Setup Click to open set up window Note This feature sets the internal clock from an Internet server The DVR must be connected to the Internet for this feature to work See Local Area Network LAN Setup on page 28 SYSTEM SETTINGS Enable time nist gov omar Dera oy Ea Figure M a Server Address Select server b Time Zone Select time zone c Click Update Now Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes 8 Language Select preferred language 9 Video Format Default is NTSC which is the standard in the United States Leave it set to NTSC 10 Menu Time Out Select how long menu will display Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes Page 17 6 bal Set Recording Mode Recording Schedule Record gt Schedule RECORD 00 06 12 18 23 J Normal Motion Copy Sun v To Al Copy OHI v To Moca a Ee Figure N wn m j Z Q wn 1 Channel Select Channel 2 Week Select day of week 3 Schedule Table a 00 23 represent 24 hours of the day b Two rows of boxes below represent corresponding hours Top row When selec
17. ate Controls Pause 13 13 Fast Forward Stop Start Manual Recording Open Menu Escape PTZ Left Menu Down PTZ Down Confirm Selection Edit Selected Setting PTZ Right Page 6 For technical questions please call 1 800 444 3353 RCA Audio Output VGA Port USB 2 0 Port RS485 PTZ Connector Item 61229 DVR Accessories Power Adapter BNC to RCA Cable BNC RCA to Power to DVR Monitor to DVR A Pa Remote Control Functions Remote Select Channel Toggle 4 and 9 Screen Displays Mouse MUTE SUBMENU Open Pop Up Menu Note _ MenuUp Yf 2AM O v MenuDom batteries P lt Menut O O o included gt Menu Right 2 Confirm Selected Operation P lt Rewind Z _ Play Search Records E gt Fast Forward Ww e Record i O o W Pause O y yO w Stop S Figure D Camera and Accessories Power Adapter Power Splitter Power Mounting Hardware Power from Adapter to Splitter J Screws Power Anchors o to Cables xN Cable 60 ft Camera Hood Cens Video to Cable a 4 Video a7 Sr from Camera Power Video to Camera to DVR Item 61229 N Power from Splitter For technical questions please call 1 800 444 3353 Power from Cable A Figure E Page 7 Quick Start Guide Flow Charts Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all tex
18. ature A Connect Monitor Connect TV or PC monitor sold separately to DVR using BNC to RCA cable included or VGA cable sold separately B Connect Cameras 1 Connect Video Yellow from Cameras to Cables 4 Connect Power from Cables to Splitter 2 Connect Power Red from Cameras to Cables 5 Connect Splitter to Camera Adapter 3 Connect Video Yellow from Cables to DVR C Connect Mouse Plug the Mouse in one of the USB ports D Connect Power SETTINGS Note Only use supplied Power Adapters 4 Plug Camera Splitter plug into surge protector and a surge protector sold separately 5 Plug surge protector into 120V outlet 1 Plug Monitor into surge protector CAUTION The Power Adapters MUST be 2 Plug DVR Adapter into Power Input on DVR plugged in indoors in a clean dry location 3 Plug DVR Adapter plug into surge protector 6 System will boot up Initializing 1 After boot up system will initialize 3 Press and hold the REW button until ee it beeps to activate the controls 2 Arter initialization is complete system will beep then display Main Interface 4 Make sure that all cameras are operating with live images from cameras Item 61229 For technical questions please call 1 800 444 3353 Page 13 wn m j Z o wn Cameras Before Mounting 1 Place Cameras in intended locations When planning mounting locations and angles a Take into consideration the length of the
19. cal questions please call 1 800 444 3353 Page 15 Main Menu Map 2 Live ToT N Display Output 2 N Privacy Zone p 2 Rec Para 2 oO Schedule 1 Record ae oO MainStream p 2 O Record Search p 2 Event Search p 26 Search O Backup p 2 wn m j Z Q wn 2 O Log ke Network p 2 Network DDNS 2 xe 3 ge 2 Ko Email ke Mobile 2 Ko 1 o Alarm Motion ToT HDD p 27 Device PTZ p 27 General p 17 System Users p 20 Version p 21 Maintain p 24 Advanced Events p 24 Figure J Page 16 For technical questions please call 1 800 444 3353 Item 61229 Set Date and Time Main Settings System gt General Set Date and Time Daylight Saving Time Network Time Protocol Language and Video Format SYSTEM C Dear Ay ee Figure K 1 Date Set current date System Time Set current time Date Format Select date format Time Format Select time format a e DN DST Setup Click to open setup window General Users Version mo Olsabie 9 s v 02 00 00 02 00 00 Figure L 6 Daylight Saving Time Select Enable or Disable a Time Offset Select 1Hour or 2Hour b Daylight Saving Time Mode e Week Set month week day of week and time for change to occur e Date Set date and time for change to occur Item 61229 For technical questions ple
20. dings on a MAC in H 264 format Insert supplied CD into computer open MAC_Record Player and follow instructions AVI Generator For converting recordings from H 264 to AVI format Insert supplied CD into computer open AVIGenerator and follow instructions Smartphone For connecting to the DVR from a smartphone To use this feature the WAN needs to be set up first 1 Insert supplied CD into computer Note The phone s Unknown Sources setting and open Mobile Software folder for MUST be enabled to allow installation Depending instructions according to phone type on Android version installed software and settings additional software may be required to allow installation of viewing software 2 Go to Network gt Mobile to view the Mobile Port settings you will need Z m j A A Page 32 For technical questions please call 1 800 444 3353 Item 61229 Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified A technician Camera Maintenance AWARNING TO PREVENT SERIOUS INJURY FROM ELECTRIC SHOCK Unplug the Power Adapter from its electrical outlet before inspection maintenance or cleaning 1 PERIODICALLY inspect the general 2 PERIODICALLY wipe external surfaces condition of the Camera Check for of Camera with clean cloth loose hardware 3 Maintain area surrounding Camera damaged cord electrical wiring making sure obstacles don
21. djustment Wheel 2 Loosen Adjustment Screw tilt Camera as needed then tighten Adjustment Screw Note Only loosen Adjustment Screw slightly do not remove it Page 14 For technical questions Note Route Cable through slot on Base to keep Base flush with mounting surface 4 Drive Screws through mounting holes in Base and into anchors until the Camera is securely attached to the mounting surface Adjustment Wheel Adjustment Screw Figure G please call 1 800 444 3353 Item 61229 DVR Settings Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Note In all of the following instructions the Mouse will be used for navigating all system menus Pop Up Menu To access Pop Up Menu right click anywhere on screen or hover over bottom of screen 4 way Record Split Stop PIP Screen PTZ Zoom Record x1 Volume E E E ORN Main 9 way Start Record Start PIP D Menu Split PTZ Search SEQ x2 2 Screen Cruise a W Figure H Tp Main Menu Shortcut To Main Menu__ Zoom Zoom PTZ Camera Stop Recording Images Stop Rotation PIPx2 Two Pictures In Picture Sound Level Main Menu To access Main Menu bring up Pop up menu then click on Main Menu icon MAIN MENU ee ee w SEARCH NETWORK P ALARM c DEVICE 7 F SYSTEM X saias Figure Item 61229 For techni
22. e it below b Press Enter c Allow ActiveX control to install Note You my need to adjust the settings in Internet Explorer by adding the http address to Trusted Sites and modifying ActiveX controls 7 After ActiveX Control installs Log in to DVR using User Name and Password 8 The DVRcan now be controlled by a remote computer or smartphone Page 30 For technical questions please call 1 800 444 3353 Item 61229 Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product The supplied CD contains the software needed to connect to the DVR and play back recordings on a computer or smartphone DVR Client For use with a local or remote PC to set up connection to the DVR For local computer the LAN needs to be set up first For remote computer both the LAN and WAN need to be set up first System Requirements Intel Pentium 4 or higher 3GHz Min 2GB Operating Windows XP Professional Windows System Vista Windows 7 Windows 8 Disk Space Min 10GB Installation 1 Insert supplied CD into computer open Video_Client and follow instructions to install the program 2 Create Administrator User Name and Password 3 Video surveillance client will open Figure AS Add DVR 1 Click Config to open Local parameter c Client Port Enter Client Port from configuration window Network
23. eam cccceceeeeesecceceeeeeeeeeeees 23 Parts List ic icccsiitieies Gtectieatiaecste 35 Maintain Hard Drive cece 24 Warranty oecccccicconccicmenciniaraei 36 POMS insana aaa 24 WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol Itis used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER Indicates a hazardous situation which if not avoided will result in death or serious injury AWARNING Indicates a hazardous situation which if not avoided could result in death or serious injury Indicates a hazardous situation which if not avoided ACAUTION could result in minor or moderate injury NOTICE CAUTION Addresses practices not related to personal injury IMPORTANT SAFETY INFORMATION AWARNING Read all safety warnings and instructions Failure to follow the warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference Page 2 For technical questions please call 1 800 444 3353 Item 61229 Installation Precautions 1 Check federal state and local surveillance laws before installing video and or audio surveillance equipment 2 Install only according to these instructions Improper installation can create hazards 3 Do not overreach when installing this product Keep proper footing and balance at all times This en
24. ens 5 Search Recordings ccceeeeeteeeeeneaee 25 Set up Before Use eeeeeees 6 Backup Recordings eeeeeeeees 26 Quick Start Guide Flow Charts 8 Format Drives c ccccceceeeseeseeeeeseeeeees 27 DVR Equipment Connectionse 12 PTZ Camera sinea adidas dhacees 27 DVR Settings 15 Local Area Network Setup 28 Pop Up Menu cccceccecceeeeeeeeeseeseeeeees 15 Set up Remote Video Stream 29 Main Menu ccccccceeeeeeeeeeeeseeteeeeees 15 Set up Email Capability ee 29 Main Menu Map cceeeeeeeeeeeeseeeeeees 16 Set up Smartphone Capability 29 Main Settings scire 17 Wide Area Network Setup 0 0 30 Recording Schedule ceeeeeeeeeeees 18 DOMWANG oecesiisccdectseierderviidecnvneeine 31 Motion Detection ceeeeeeeeeeeees 19 DVR CHOI cei dic caserderaateestivenniatiaecnanteness 31 USES nuca 20 Vid o Player cnrcencnmenrereaniaini 32 System Information 21 MAC Record Player 32 Display Settings eeeceeeeeeeeeeeees 21 AVI Generator o oo eect eeteeeeeeeeteeeeeeeee 32 Display Output enerne rennene 22 Smartphone cccccceceeeeeeeeeeseneeeaeeees 32 Privacy Z NES erraia a 22 Maintenance Instructions 33 Recording Parameters 23 Troubleshooting cccceceseeeeeeeeee 34 Video Str
25. find a specific event when the date and time of event are known 1 Search Date Enter the date of the recording 2 Replay Time Enter the time of the recording 3 Click Play to bring up the channel list Z O H lt aa Lu ou O 4 Select Channel s Click on channel boxes then click Play 5 The Playback Control Bar will pop up on bottom of screen See Figure AE and Figure AF above Note To recall Playback Control Bar move the mouse To exit recording click X on Playback Control Bar then click Exit to return to Record Search Page 25 e v m S e zZ Backup Recordings Search gt Event Search Playback and Back up recordings SEARCH Search Date CH A fy Search Time TYPE Al fy 01 Normal 11 08 30 09 14 4 27 102K O1 Normal 11 08 30 00 16 56 00 19 10 27 4M 7 03 Normal 11 08 30 00 16 66 00 19 10 27 3M 06 Normal 11 08 30 0 16 66 00 19 10 27 9M 07 Normal 11 08 30 09 16 56 00 19 10 274M gt mt Al Twerse so o Search Backup Exit Figure AG Enter date heck box for h I4 Goto first set of recordings lt Gotoprevious set of recordings gt Goto next set of recordings Goto last set of recordings and select opposite recordings Search Search for selected recordings Perform Back up Ext Go back to Record Search Figure AH Search gt Backup Search Date Set date to search CH Select Channel Searc
26. gt Network settings on DVR 2 Click on Device manage Channels Enter how many Cameras to view 3 Right click on Device List then click Add Device User Name Enter User Name for DVR This will open Manually add the device window Password Enter Password for DVR aq Oo A Auto Login Enable automatic log in to the DVR when DVR Client is launched Click OK the device will appear on the Device info list Manually add the device Device Info Device 101 Device IP 192 168 001 101 h Client Port 2051 Channels UserName admin Password Area Name Device list AutoLogin Disable ji 4 n Cance Fi AT 5 On Device List right click on the DVR icon the igure name you assigned to DVR and click Login then a Device Assign name to DVR right click again and click Open All channels b Device IP 6 The DVR can now be controlled e LAN computer use DVR s LAN through the software Address from chart on page 28 Exit out of Local parameter configuration window NETWORK Note For more instructions refer to DvrClient Remote computer use DVRs Public User Manual included on the supplied CD IP Address from page 28 Item 61229 For technical questions please call 1 800 444 3353 Page 31 Video Player For playing back recordings on a Windows PC in H 264 format Insert supplied CD into computer open Video_Client and follow instructions MAC Record Player For playing back recor
27. h Time Enter beginning search time in first box and ending search time in second box TYPE Select All Normal or Alarm recordings a Normal recordings are scheduled or manual recordings b Alarm recordings are recordings started automatically by motion detection Click Search to populate table Select recordings to backup a To mark all recordings for backup click ALL b To mark recordings for backup click on BAK box for each selection c Click Backup and click OK to backup selected recordings Back up recordings Search Date CH Al Search Time O00 fax69 TYPE Al Waring 3 44 gt WAP Therese Figure Al 1 Search Date Set date to search 2 CH Select Channel Page 26 For technical questions please call 1 800 444 3353 Search Time Enter beginning search time in first box and ending search time in second box TYPE Select All Normal or Alarm recordings a Normal recordings are scheduled or manual recordings b Alarm recordings are recordings started automatically by motion detection Click Search to populate table Select recordings to backup a To mark all recordings for backup click ALL b To mark recordings for backup click on BAK box for each selection c Click Backup and click OK to backup selected recordings Item 61229 Search gt Log e Log Type Select Log type LogType All x Search Start Time End Time TYPE CON TIME POINT RECORD Start Time Da
28. ions edges or moving parts Damaged or entangled discussed in this instruction manual cannot cords increase the risk of electric shock cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator A SAVE THESE INSTRUCTIONS AWARNING TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded Do not modify the power cord plug provided with the tool Never remove the grounding prong from the plug Do not use the tool if the power cord or plug is damaged If damaged have it repaired by a service facility before use If the plug will not fit the outlet have a proper outlet installed by a qualified electrician 1 The included Power Adapters do not require grounding The Power Adapters may be used in S e either of the 120 volt outlets shown in the preceding illustration See Figure A Figure A Outlets for 2 Prong Plug N Extension Cords Note Do not use an extension cord with the Power Adapters Symbology Double Insulated GR Canadian Standards Association m temato Current Underwriters Laboratories Inc Page 4 For technical questions please call 1 800 444 3353 Item 61229 Specifications DVR Hard Drive 500 GB Video Sta
29. l not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes Allows selection of up to four areas to be blocked from being viewed or recorded Figure W 1 Channel Select Channel 2 Privacy Zone Toggles Privacy Zones 3 Area Setup Select up to 4 areas to block Page 22 For technical questions please call 1 800 444 3353 4 Mask Area Select Setup then click and drag green square s to move and resize areas to be blocked 5 Right click anywhere to return to Privacy Zone Click Apply then OK to save changes 6 Repeat steps above for other Channels 7 Copy Copy parameters from one Channel to other Channels a Select Channel to copy from b Select Channel to copy to or select ALL c Click Copy then click OK Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes Item 61229 Recording Parameters Record gt Rec Para SETTINGS 4 PreRecord Enable to start Motion Detection recordings immediately before motion is detected Keep this enabled in most circumstances 5 Copy Copy parameters from one Channel to other Channels a Select Channel to copy from Copy OMI v b Select Channel to copy to or select ALL c Click Copy then click OK Figure X Changes will not be saved unless you click Apply then OK 1 Channel Select Channel Click Exit to return to System and 2
30. me parts are listed and shown for month and year of purchase instead illustration purposes only and are not available individually as replacement parts Item 61229 For technical questions please call 1 800 444 3353 Page 35 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product To the extent that this product is used with software other than what is provided we shall in no event be liable for any damage to your computer or loss of data Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned
31. ndard NTSC PAL Video Codec H 264 Input 8 BNC Output 2 BNC 1 VGA Audio Codec G 711 Input 1 RCA Output 1 RCA Video I O Audio O CIF 352 x 240 Resolution HD1 704 x 240 Recording D1 704 x 480 Up to 30 fps each channel Recording Mode Manual Schedule Motion Detection Remote Motion Detection Selectable Area and Sensitivity Detection PTZ Interface RS485 Supports Pelco D P camera sold separately Network Interface RJ 45 10m 100m Ethernet Interface USB Interface USB 2 0 DVR Input Rating 12VDC 2A Operating Temperature 32 131 F SETTINGS Cameras Lens Types 2 Cameras with fixed 6 mm lenses 2 Cameras with fixed 3 6 mm lenses Horizontal Resolution 400 TVL Effective Pixels 648H x 488V Night Vision Type Infrared LEDs with Low Light Sensor Image Type Daylight Color Infrared Black amp White Cable Length Operating Temperature Item 61229 For technical questions please call 1 800 444 3353 Page 5 wn m j Z Q wn Set up Before Use A Components and Controls DVR Front Panel Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Bunker Hill Security 6 Previous Channel _ __ _ _ 8 Toggle 4 and 9 Screen Displays _ _ _ 9 MenuUp PTZUp O Note Controls for PTZ mode are italicized DVR Back Panel Rewind Activ
32. nstructs you to do so 4 Load Default Click to restore all system default settings Siar py Ea Figure AA 5 Reboot Click to manually reboot system 1 Auto Maintain Enables Auto Reboot 6 Shut Down Click to manually shut down system Changes will not be saved unless 2 Auto Reboot Select when to Reboot system you click Apply then OK a Everyday Enter time for Reboot Click Exit to return to System and discard unsaved changes wn m j Z Q wn Alerts Advanced gt Events Set up alerts for when the hard drive has no disk space 3 Show Message Check box to show a when there is a disk error or a camera loses video message or uncheck to not show a message 4 Buzzer Click drop down box to choose Buzzer duration or turn Buzzer off vi 5 Send Email Check box to send an email cea Seas or uncheck to not send an email a oo Note The DVR must be connected to the Internet for email function to work See Network gt Network on page 22 Changes will not be saved unless you click Apply then OK Te a E Figure AB Click Exit to return to System and 1 Event Type Select Event type discard unsaved changes 2 Enable Check box to Enable or uncheck to Disable Page 24 For technical questions please call 1 800 444 3353 Item 61229 DVR Operating Instructions Search Recordings Search gt Record Search SEARCH Record Search Event Search Backup Log
33. peration PTZ Contre PTZ camera sold separately Figure R Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes Repeat steps above for other Users Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes se Call 1 800 444 3353 Item 61229 System Information System gt Version View and Set Device Information Device Name Set Device Name up to 21 characters SETTINGS 2 Device ID Set Device ID number up to 6 numbers se 3 Device Type Cannot modify f 4 Hardware Ver Cannot modify i 5 Software Ver Cannot modify 6 IE Client Ver Cannot modify Figure S 7 MAC Add Media Access Control address MAC Address needs to be changed when multiple DVRs are on the same network Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes Display Settings Display gt Live Set how Camera information will display Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes 5 Covert Enable to conceal live image 6 Show Time Toggles date and time display 7 Record Time Enable to record date and time Changes will not be saved unless Figure T you click Apply then OK 1 Channel Select Channel Click Exit to return to System and discard unsaved
34. rm SETTINGS Figure O 10 Post Recording Select how long recording will 1 Channel Select Channel continue after motion is no longer detected 11 Copy Copy parameters from one 2 E le lect Enabl Di le ees een nee ee ete Channel to other Channels 3 Area Click to set area where motion is detected a Select Channel to copy from 4 Sensitivity Set sensitivity level b Select Channel to copy to or select ALL 5 Show Message Check box to show message c Click Copy then click OK on screen when Motion Detection is triggered Changes will not be saved unless i 6 Buzzer Check box to hear audible alarm you click Apply then OK when Motion Detection is triggered Click Exit to return to System and discard unsaved changes Item 61229 For technical questions please call 1 800 444 3353 Page 19 wn m j Z Q wn Users System gt Users The system supports one administrator and 8 six users The administrator has permission to perform all activities and is authorized to set up permissions for all other users SYSTEM General Users Version ope ree eon mp om e p a S o a foa oe 1 OCE oe TO ee ee r Sar Figure P Set up Administrator 1 Select admin and click Edit 2 User Name Set User Name up to 8 characters 3 Password Enable Select Enable or Disable Note When Password is Enabled a key icon will appear on Pop Up Menu Click on key to enable Menu
35. t under subheadings therein before set up or use of this product Use the following flow charts to help make the cable connections navigate the system and set up or change the unit settings Refer to the individual setup sections in this manual for detailed instructions on specific tasks INITIAL SETUP m Physical Connections gt See Page 12 Connect Connect Connect Connect Mount Monitor Cameras Mouse Power Cameras wn m j Z Q wn Video Output j r AA Lal ed E Lad La Note Monitor and Surge Protector sold separately Page 8 For technical questions please call 1 800 444 3353 Item 61229 Set Date and Time See Main Settings on Page 17 In DVR Main Menu Select System Select Set Date and Click Apply General Time then OK See Recording Schedule on Page 18 Set Date and Time above Which Press REC on Recording front of DVR mode red light will flash SETTINGS In DVR Select Channel Main Menu Brot and Day of select Record Week Scheduled Select boxes Repeat for all for Normal and Days and all Click Apply Motion Channels then OK Motion Detection Settings See Motion Detection on Page 19 CL Set Date and Set Recording Time above Mode above In DVR Main Menu Select Alarm Select Motion P S Set Sensitivity Select whieh Level will record Select Area Set Buzzer for Click Apply R R R audible alarm then OK Item 61229
36. te Enter start date End Time Date Enter end date E Devke 11 08 30 00 00 61 NO NO TEEN 11 08 30 00 01 01 6 System Ip Advanced Se Figure AJ Click Search to populate table a N Click Backup to backup log file then click OK when backup finished Format Drives Device gt HDD Note The drive will save recordings as long as possible before overwriting while in Auto mode If CH Close is selected the drive will not be overwritten fos fosse fen ejo fose fimo O 2 Format Hard Drive a Click Select box for drive to format Overwrite Awo O FERATOT FERNUSE b Click Format HDD c Click OK d When formatting is finished click OK A Hdd full overwrite laster Record file Siar ET ME Figure AK 3 Format USB Drive a Install drive into USB port No O ID number of drives state OK Hard drive installed be O PONAT HRE No disk No hard drive installed c Click OK Z Free total Free Space Total Space d When formatting is finished click OK O Be cofdlng ine svallable Changes will not be saved unless gt Figure AL you click Apply then OK fad L 1 Overwrite Select how long to save recordings Click Exit to return to System and A on Hard Disk Drive before overwriting discard unsaved changes fe PTZ Camera Device gt PTZSetings for PTZ Pan Tilt Zoom camera sold separately Input information according to PTZ camera manufacturer instructions
37. ted boxes will turn green to indicate Normal continuous recording This is the Default setting Bottom row When selected boxes will turn yellow to indicate recording will be triggered by Motion Detection c Copy Date Copy parameters from one Day to other Days d Select Day to copy from e Select Day to copy to or select ALL f Click Copy then click OK Copy Channel Copy parameters from one Channel to other Channels a Select Channel to copy from b Select Channel to copy to or select ALL c Click Copy then click OK Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes Page 18 For technical questions please call 1 800 444 3353 Item 61229 Motion Detection Setti Ale otion Detection oe Ings Motion Detection Alarm gt Motion Set up parameters for triggering 7 Send Email Check box to have email sent recordings by Motion Detection when Motion Detection is triggered Note The DVR must be connected to the Internet for this function to work See Wide Area Network WAN Setup on page 30 C a E 8 Full Screen Check box so that when Motion Detection is triggered the Camera s CEE view will display in full screen mode Record Channel Post Recording 308 v KEEA 9 Record Channel Check box to Enable Disable Gma eal O CME aa motion recording Highlight Channels to link Sar EN ar recording to this Channel s motion ala
38. to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state FCC STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Bunker Hill Security 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
39. work SubStream Email Mobile DDNS ox Wwe Foe Svan Ae o a o a A pa e aie el e e e CIEC fos e eT ie foo ene Te eet _ for erate ae eel _ oo ene eT eel _ Default Apply ET Figure AP Enables email to be sent when Motion Detection is triggered Note Follow instructions from email provider to set up this feature NETWORK as s Network SubStream Email Moble DONS onm pom am Sender Email reresal Pie ame Berar Apply Ext Figure AQ e Set up Smartphone Capability Network gt Mobile 1 Sender Email The email address that the notification will be sent from 2 Sender Pwd The password for the email account that the notification will be sent from 3 Receiver Email The email address that the notification will be sent to Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes NETWORK Powe fe Default Apply Ew Figure AR Item 61229 1 UserName Set User Name 2 Password Set Password 3 Mobile Port Set Port to 3002 Changes will not be saved unless you click Apply then OK Click Exit to return to System and discard unsaved changes For technical questions please call 1 800 444 3353 Page 29 NETWORK Z m j A A Wide Area Network WAN Setup Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual
Download Pdf Manuals
Related Search