Harbor Freight Tools 7 Pc 3/4 Oz. Quick_Change Airbrush Kit Product manual
Contents
1. for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MER CHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return re paired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 SKU 93506 For technical questions please call 1 800 444 3353 Page 72. AL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBU TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 93506 For technical questions please call 1 800 444 3353 Page 6 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability stan dards and warrants to the original purchaser that this product is free from defects in materials and workman ship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal ac tivity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or
3. CENTRAL PNEUMATIC TO o QUICK CHANGE AIR BRUSH KIT Model 93506 ASSEMBLY and OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2005 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Specifications Fluid Capacity 3 4 oz Air Inlet 1 4 NPT Working Pressure 15 to 50 PSI Fluid Jar Size Qty 5 1 3 8 Dia x 2 H Air Brush Dimensions 5 1 2 x 1 3 8 x 3 3 4 Note This Air Brush works with a regulated small air compressor with an air regulator none included The air pressure must not exceed 50 PSI Save This Manual You will need the manual for the safety warnings and precautions assembly instruc tions operating and maintenance procedures parts list and diagram Keep your in voice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using tool basic safety precautions should always be followed to reduce the risk of personal injury and damage
4. aint may dry and clog the Air Brush 3 Have a spare Jar 6 filled with thinner or water depending on the type of paint be ing sprayed 4 When finished spraying release pressure on the Lever 9 Immediately remove the paint jar from the Air Brush and attach the spare Jar 6 Continuously spray on scrap white paper until the paint residue in the Air Brush is sprayed out Cleaning 1 Remove excess paint from the Jar 6 and clean thoroughly 2 Spray thinner or water depending on the paint used through the Air Brush until it is entirely clean Plug up the Fluid Cap 1 with a soft cloth and force air and solu tion through the cap and tip Troubleshooting If the Air Brush becomes clogged disconnect from the air source and clean as stated above Next gently un thread counterclockwise the Fluid Cap 1 and Air Tip 7 Clean the parts in thinner and replace SKU 93506 For technical questions please call 1 800 444 3353 Page 5 Parts List and Assembly Drawing Description Fluid Cap O ring Jar Lid Tube Cover Gasket Jar 3 4 oz Qty 5 Air Tip 1 2 3 4 5 6 7 8 O ring Lever Body O ring Air Valve Pin O ring Air Valve Spring Air Inlet Air Hose 1 4 NPT Adapter Note 17 1 4 NPT Adapter not shown PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANU
5. are doing use common sense Do not operate any tool when you are tired 10 Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician 11 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools 12 Do not operate tool if under the influence of alcohol or drugs Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs If there is any doubt do not operate the Air Brush 13 Maintenance For your safety maintenance should be performed regularly by a qualified technician 14 Use compressed air from a small regulated air compressor Use clean dry regulated air at 15 to 50 PSI Never use oxygen carbon dioxide combustible gases or any other bottled gas as a power source for this tool Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations
6. ir supply 1 Fill the Jar 6 with strained paint Do not fill over 2 3 full 2 Carefully thread on the Jar Lid 3 3 Attach one end of the Air Hose 16 to the Air Inlet 15 on the Air Brush Attach the other end of the Air Hose 16 to the regulator not included which then attaches to the air supply using the 1 4 NPT Adapter 17 The air source must be adjustable between 15 and 50 PSI Thoroughly read the instructions and safety warnings provided with the air compressor and air regulator before using SKU 93506 For technical questions please call 1 800 444 3353 Page 4 Adjusting Paint Flow and Air Flow 1 Use the air regulator not included to regulate air flow You must purchase a regu lator that can be adjusted to between 15 and 50 PSI Since there is no pressure gauge you will have to test the Air Brush on a piece of scrap material to determine the desired setting 2 On the Air Brush turn the Fluid Cap 1 to adjust paint flow For maximum flow turn the cap counterclockwise For minimum flow turn the cap clockwise See FIGURE 1 on page 4 and the assembly drawing on page 6 Spray Painting 1 In a well ventilated area press the Lever 9 to test the spray on test material Hold the Air Brush six inches from the material and make the necessary adjustments 2 Practice spraying even strokes to avoid drips Note Since enamels and lacquer paints dry quickly do not leave the Air Brush for more than a few seconds or the p
7. that may occur It must be under stood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator WARNING The brass components of this product contain lead a chemical known to the State of California to cause birth defects or other reproductive harm California Health amp Safety code 25249 5 et seq Unpacking When unpacking check to make sure the parts listed on page 6 are included If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual as soon as possible SKU 93506 For technical questions please call 1 800 444 3353 Page 3 Operation FIGURE 1 Lever 9 Air Tip 7 Fluid Cap 1 Jar Adapter 3 Air Hose 16 Mixing and Thinning Paints Before attempting to spray any paints through the Spray Gun dilute them accord ing to the manufacturer s directions for use with Spray Guns General Rules 1 If mixing colors only mix together the same types of paints i e lacquer with lacquer or acrylic with acrylic 2 Thin paint according to paint manufacturer s directions Typically enamel and lac quer paints are diluted with one part thinner to one part paint 3 Before spraying make sure the diluted paint is thoroughly mixed 4 Mix the paint in a clean jar We recommend straining the paint before filling the Jar 6 Attaching the Air Hose 16 and the Jar 6 to the a
8. to equipment Read all instructions before using this tool 1 Keep work area clean Cluttered areas invite injuries 2 Observe work area conditions Don t expose to rain Keep work area well lit Do not use a propellant can in the presence of flammable gases or liquids Always spray in a well ventilated area 3 Keep children and bystanders away Children must never be allowed in the work area Do not let them handle machines tools extension cords or air hoses 4 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children 5 Use the right tool for the job Do not attempt to force a small tool or attachment to do the work of a larger industrial tool There are certain applications for which this tool was designed It will do the job better and more safely at the rate for which it was intended Do not modify this tool and do not use this tool for a purpose for which it was not intended 6 Use eye and nose protection Wear and ensure all people in the work area wear ANSI approved impact safety goggles and an ANSI approved dust mask or respirator 7 Maintain tools with care Keep Air Brush clean for better and safer performance Follow instructions for changing accessories 8 Do not overreach Keep proper footing and balance at all times SKU 93506 For technical questions please call 1 800 444 3353 Page 2 9 Stay alert Watch what you
Download Pdf Manuals
Related Search