Harbor Freight Tools 67802 User's Manual
Contents
1. 444 3353 Never attach or use any other form of optical device with this product Use as intended only Do not modify in any way as this may result in hazardous radiation exposure This product is not a toy Do not allow children to play with or near this item Inspect before every use do not use if parts are loose or damaged Maintain product labels and nameplates These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement SKU 67802 Battery Installation I Replacement Before first use or if the Battery Indicator shows empty then replace the battery 1 Slide the Battery Cover down and off the back of the Meter Remove the old connected Battery 3 Disconnect the old Battery Dispose of it properly or recharge if rechargeable 4 Reconnect new 9V Battery It will properly attach only one way 5 Insert connected Battery into compartment 6 Slide the Battery Cover closed SKU 67802 For technical questions please call 1 800 444 3353 Page 3 li 2 Laser Opening Laser light comes from this opening during use Point away from eyes Sensor This measures the location aimed at with the laser Do not cover during use Display ec om Foo O00 mm welt READ EA ME Lew REC ALL 4 lt a T yle Measure Frompmfere 5 Figure A Components Figure B Display Area Volume Sh2. Press MEM RECALL later to display stored memory and clear it MEM will disappear from Display MEM RECALL can be used in steps 1 or 3 of Addition instead of taking new measurements Area Volume Calculation Note Area volume calculation cannot be exited before calculation is complete 1 Press CO button to enter area calculation mode or press Qj button to enter volume calculation mode 2 The Lwill blink Take measurement for length as explained under Distance Measurement 3 Then the W will blink Take measurement for width as explained under Distance Measurement 4 For area calculation the H will blink Take measurement for height as explained under Distance Measurement 5 The area volume is displayed as Total Result at the bottom of the display 6 The Current Result will display the last measurement taken Press READ briefly to cycle through the measurements taken L L 7 Press w or Q button to take another area or volume calculation 8 Press and hold READ button for a few seconds to exit area volume calculation For technical questions please call 1 800 444 3353 Page 7 Record Serial Number Here Note If product has no serial number record month and year of purchase instead Note Replacement parts are not available for this item PITTSBURGH 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
3. EAD is pressed For a continuous measurement press and hold READ while moving Each measurement erases the previous one Measured distance is displayed as Current Result at top of the Display Unit automatically turns off after 30 seconds of inactivity TIPS There must be no objects in the measurement path For accuracy choose a target that is flat and large with hard surfaces or put a piece of cardboard in front of the target The meter will only measure up to glass but not through it Addition Note Addition can be used for distance area or volume measurements However those measurements are different units for example feet square feet and cubic feet and cannot be added together 1 Take first measurement as explained under Distance Measurement 2 Press button A will appear above and to the left of the Current Result 3 Take another measurement as explained under Distance Measurement 4 Press button again Combined measurement is displayed as Total Result at the bottom of the display 5 Steps 3 and 4 can be repeated to add more measurements For technical questions please call 1 800 444 3353 SKU 67802 SKU 67802 Memory Note Memory can be used for distance area or volume measurements Press MEM INPUT to store displayed Total Result in memory If only a Current Result is displayed it will be stored instead MEM will appear on Display
4. PITTSBURGH Laser Range Finder Item 67802 INSTRUCTIONS AND PRECAUTIONS Visit our website at http www harborfreight com AWARNING Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 800 444 3353 as soon as possible Copyright 2011 by Harbor Freight Tools All rights reserved No portion of this document or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this document may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included For technical questions please call 1 800 444 3353 Specifications Working Range 32 Accuracy Battery Product Label AVOID EXPOSURE Laser light is emitted from this aperture RANGE FINDER ITEM 67802 CAUTION LASER LIGHT DO NOT STARE INTO BEAM Max Output 1 mW Wavelength 650 nm CLASS Il LASER PRODUCT This product complies with 21 CFR 1040 10 and 1040 11 Laser Diode Mfr Sean amp Stephen Corp 4F NO3 Ln 335 Sec 4 Hsin Yi Rd Taipen China Manufacture Date z Page 2 Important Safety Information oa For technical questions please call 1 800
5. ows whether area or volume is being measured and what part is being measured Length Width or Height Addition A here means that the next measurement will be added to the current one Current Result The distance last measured or currently being measured Battery Indicator The estimated battery charge level See Battery Installation Replacement on page 3 Memory MEM means a measurement is stored in memory Total Result Total area volume or result of addition Page 4 For technical questions please call 1 800 444 3353 SKU 67802 4 Buttons 5 Measurement Base Rest this base against the surface you want to measure from b before taking a measurement SKU 67802 For technical questions please call 1 800 444 3353 Tim ae Figure C Buttons Read Takes a measurement MEM Input Stores current measurement to memory MEM Recall Displays stored measurement from memory then clears it from memory FT M Toggles between foot and meter units of measure L Volume calculation mode Ww Area calculation mode Toggles addition mode Page 5 Read the ENTIRE A IMPORTANT SAFETY INFORMATION section at the beginning of this document before set up or use of this product Distance Measurement 1 Page 6 Place measurement base against object to measure from Point at target and press READ Laser will show only while R
Download Pdf Manuals
Related Search